Search Documents

By B. Madelin

Over the last ten years, Minemet Recherche and Metaleurop have used an approach in order to investigate and improve the operation of its Smelting furnace and its lead blast furnaces. This approach gives importance- to three complementary means of investigation : - Probing campains in the industrial furnace (temperature and gas analysis profiles), - Chemical and physical modeling (coke combustion, sinter reduction modes, flows patterns, ?.) , - Staged mass and heat balances or kinetic model. This allows to define the limits of operation of each blast furnace and to predict the influence of operating parameters on the furnace performances. For the zinc Imperial smelting furnace, the probing results show the existence- of both an Isothermal reserve zone at 1015ºc and a chemical equilibrium between ZnO and gas which makes possible the use of a practical model for heat and material balances. In particular, very good prediction on the influences of operating parameters can be made. On the contrary, for lead blast furnaces, the probing results show that the thermal and chemical equilibria are not reached. Consequently, classical models for staged heat and mass balances are not sufficient. The use of the other means allows then to characterize the specific influences of operating parameters on the thermal instabilities of these furnaces and their allowed limits.

Jan 1, 1990

By Walter E. Lewis

Ventilation-air-heating plants are in use at several iron mines on the Menominee Iron Range, Iron River, Mich. Many of the mines are exceptionally wet; during winter months, when fresh air is forced down the wet air shafts into the mine, it is usually necessary to heat the fresh air to above freezing so that the openings will not be closed by ice. The problem of ice closing air shafts has been solved by the practice of reversing the air current before the openings have become completely closed. This procedure involves drawing warm air from the mine up the usual down-draft air shaft. The M. A. Hanna Co. has found, at some of their mines on the Menominee Range, that it is more convenient to heat the below-freezing air rather than reverse the air current. Intermittent freezing and thawing of ice that has formed in the air shaft tends to loosen the wall rock, requiring major shaft repairs. The openings are kept free of ice the year around by heating the fresh air during periods of below-freezing weather. Table 1 shows the monthly minimum moan, maximum mean, and mean temperatures for the Iron River area. Under normal conditions of temperature, the furnaces are fired in November and usually are not allowed to go out until April of the following year.

Jan 1, 1951

By Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to melt residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-offgas handling system, and thermal oxidizer for final offgas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 lb/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kV?A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the offgas and serves as an acid gas scrubber. The clean offgas is heated to 1,800° F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 2010

By John Wellington Finch

THE- impression which the public has of northern Canada is that it is a' vast wilderness of forests; river's, and. lakes, sparsely inhabited by. a few Indians and `containing a few, scattered trading posts of the Hudson Bay Co. This is far from the facts. The building of the Canadian Pacific Railway led to the discovery, in 1883, of the nickel deposits of Sudbury, Ont.; these are the largest known nickel deposits in the world and produce about 90 per cent. of the world's output of nickel. The building of the Temiskaming and Northern Ontario Railway north, from North Bay, to open up farming lands along Lake. Temiskaming, resulted in the discovery and development of the great silver deposits of the Cobalt area, Ontario. Since the discovery of these deposits in 1903 to Dec. 31, .1923, Cobalt has produced a total of ' 327,301,897 oz. of silver, valued at $212,668,434, and paid in. dividends $88,338,185. In 1923 the production of Cobalt amounted to 10,285,247 oz. of silver. Just south of Cobalt, in South Lorrain,. a. new silver district has recently been developed and mills have started production. These deposits are of such extent that 'a branch railroad is under construction from Cobalt to that area. Northwest of Cobalt is the Gowganda silver area which is also a producer of silver ore and is now attracting outside attention. This area is not connected by railroad.

Jan 1, 1924

By P. Croney

Environmental monitoring requires major effort and expense but management of data receives less attention. A modem database system can manage hydrochemistry, water levels, meteorology, geology and downhole geophysics data and is flexible to allow the storage of ad hoc data. Reports can be customized by the user and derived data generated from input values. The production of high quality maps with contours and hydrochemical diagrams is an essential part of the reporting process. These maps integrate directly with the current site survey information. These facilities are best provided by storing the data in an industry standard database such as Oracle or Access to which customized AutoCAD and Microsoft Office routines make direct SQL calls.

Jan 1, 1997

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining Co.'s Granite Mountain shaft. How this insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the lire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest pro¬ducer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By C. L. Glorioso

As an introduction and credentials for our talk, let me take a moment to introduce you to Wimpey Worldwide and specifically to Wimpey Minerals, USA, Inc.

Jan 1, 1995

By P. Heald-Wetlaufer

Doubly polished sections (i.e., sections polished on both sides) allow insights into complex paragenetic relationships, the interpretation of which is essential to understanding ore-forming processes. Alternate viewing of these optically superior sections in transmitted and. reflected light facilitates the recognition and definition of growth zones in ore and gangue minerals and the interpretation of postdepositional changes, such as hydrothermal leaching and replacement. Many such observations would escape detection by conventional petrographic methods. Our procedure for preparing doubly polished sections has evolved during the past 20 years and incorporates many standard procedures. Studies from such diverse districts as Creede, Colorado, Hokuroku, Japan, and the Upper Mississippi Valley zinc-lead district, southwestern Wisconsin, demonstrate the value of observations from doubly polished sections in constructing genetic models. The advent of doubly polished sections represents a major advance in the study of ore deposits and they should be a standard tool in every ore petrology laboratory.

Jan 1, 1982

By S. Leong

This paper reports on research examining disclosures from mining companies regarding their water usage in the Macquarie and Lachlan catchment areas, both parts of the Murray-Darling Basin in New South Wales, Australia. The objective of the research was to assess whether this disclosure is sufficient to allow communities to determine whether mining companies are complying with mining conditions of consent and abiding by the requirements of their water licencing agreements. These requirements are then compared to the water reporting requirements of the Global Reporting Initiative (GRI) and the Water Accounting Framework for the Minerals Industry (WAFMI). Communities are concerned about whether the mining industry?s use of water will have impacts on their livelihoods and lifestyle and thus require information concerning the quantity of water that will be extracted, how much water will be left for other stakeholders and whether the mining will affect water quality. This is an archival study. It has involved examining relevant publically available information released by mining companies and government regulators and determining if this is sufficient to meet the needs of the local communities. Additionally, it has involved looking at information indirectly provided by mining companies, via the use of intermediaries. Further, information availability concerning basic water accounting and regulatory breeches and whether such information is available at the mine site level has been considered. It is found that while NSW legislation places very little reporting requirements on mining companies, the development consent conditions for new projects and extensions to existing projects are quite significant and should be sufficient to meet the needs of local catchment residents though such information is not always easily accessible for the layperson.

Aug 1, 2013

By J. E. Tiffany

A stick of explosive is a package of stored energy that can be released when needed to blast rocks, coal, and other materials; but, unlike fuels such as coal and gasoline, its potential energy is self-contained, there being enough oxygen within the package to complete the almost instantaneous reaction. When an explosive is ignited or detonated, the solid or liquid materials of which it is composed are converted rapidly into highly heated gases, which, if free to expand, would have a volume many times larger than that of the original explosive. At the instant of explosion these gases occupy only the volume of the shot hole and are therefore produced at a very high pressure, which causes the material that is being blasted to be broken or disrupted. In blasting coal efficiently the proper placement of the shot hole and the confinement of the explosive therein are both of prime importance. When these are not adjusted properly, only a small amount of the energy is expended in bringing down coal, consequently the balance of the energy tends to be expended by the emission of a flame into the working place that may lead to a gas or dust explosion. Permissible Explosives Defined The term "permissible explosive", as applied by the Bureau of Mines to explosives it has approved for use in blasting in coal mines, embraces not only the requirement that the explosive, when used, shall be similar in all respects to the basic sample that passed all the tests necessary for its admission to the published permissible list, but also that the explosive shall be used under certain prescribed requirements.

Jan 1, 1938

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995

By Michael A. Trevits

A mine fire represents one of the most dangerous and challenging safety issues facing underground mine operators. Given the right circumstances, a mine fire can occur at any location in the active or abandoned mine workings, can quickly grow beyond control, and threaten the welfare and livelihood of the entire underground workforce. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), has been conducting an in-depth program of research addressing mine fire prevention, early and reliable fire detection, and mine fire suppression technologies. One portion of this program is focused on understanding the characteristics of mine fire combustion products and flame spread through large scale deep-seated (firmly established) fire tests and use of computational fluid dynamics (CFD) modeling. In this study, two deep-seated fire tests were conducted; one fire consisted of coal material and the other utilized the two most abundant fuel sources found in a coal mine: coal and wooden cribbing blocks. The fires were burned to completion while the combustion products were collected and analyzed. In addition, an array of thermocouples was placed within the body of the material to measure flame spread rate. The coal fire test information was then used to develop a CFD model of the fire. This paper describes the fire tests, provides insight into characteristics of flame spread, and presents the CFD modeling work results.

Jan 1, 2009

By R. E. Heithecker

Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalk-rock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I. Although the field is divided into several districts which are more or less clearly defined and separated by unproved territory the term Zwolle field", as used in this report, includes the entire area from Blue Lake on the west side, through Zwolle proper, and eastward, including the Many or Eastern extension.

Jan 1, 1934

Although anion exchange resins are widely used for gold recovery in Russia and the former CIS, accounting for almost 50 percent of gold recovery in that part of the world, the technology has not been adopted in the West, apart from one small operation in South Africa. This situation is likely to change as the gold industry heads into the twenty first century. With gold prices having declined steadily through the 1990's, mining companies are under great pressure to reduce costs and improve gold recovery. Most studies on the use of resins for gold recovery from cyanide solution or pulp have shown that this technology has the ability to achieve both these goals. Resins can also be used to recover and recycle free and complexed cyanide in gold plant tailings, which has the potential to significantly lower operating costs, and latest developments in this area of technology are discussed. Finally, recent studies on thiosulphate leaching of gold have'shown that this process is very well suited to the treatment of carbonaceous, preg-robbing ores from the Carlin trend (Nevada, USA), and elsewhere in the world, because the gold thiosulphate complex does not load on to carbon. Whilst this obviously benefits the leaching process, it means CIP and CIL are ineffective in this situation, and the use of ion-exchange resins for gold recovery from thiosulphate leach solution are discussed.

Jan 1, 1998

By C. A. Rhoades

A major contributor to the problem of short life expectancy for blade-type conveyor belt cleaners is uneven wear along the blade edge. Uneven wear results in the formation of channels in the blade edge, which allow material to be carried back between the blade and the belt. In an effort to reduce the uneven wear problem, the U.S. Bureau of Mines has studied the mechanisms responsible for effective belt cleaning. From this study emerged a design for a cleaner blade that would greatly reduce uneven edge wear. The design consists of a standard cleaner blade incorporating air passages that allow for the expulsion of air along that part of the blade edge in contact with the conveyor belt surface. The results of 18-h tests indicated that the expulsion of air on the blade edge prevents scratches from developing into deep grooves. These tests showed that effective blade cleaning life can be extended 25 times using the pneumatic cleaning blade, compared with solid metal cleaning blades.

Jan 1, 1989

By Z. G. Li

The large-scale vibrating screen has been applied widely in coal industry and other industrial areas as a kind of important device. As vibration mechanical device, it works very hardly and works in very bad environment so that the structure of screen is damaged easily. Therefore, it is very important that how to detect the fault of structure as early as possible to make the repair schedule reasonably and economically and to avoid the body hurt and device damage. As a kind of important structure of vibrating screen, the lower crossbeam is the main carrying structure and it is easily damaged, so it is regarded as a researched object in this thesis and it is tested under the load in the laboratory. Based on the test, acoustic emission wave signals can be got-ten by modern acoustic emission testing technique. Then, the ?wavelet packet - energy? from the characteristics of acquiring signals is used as neural network input vector. In the BP network structure design, the design of a hidden layer with variable number of BP network is established. Based on the error by contrast, the best nerve number can be identified in the hidden layer. Through integrated analysis, using Levenberg-Marquard BP study algorithm, network-training errors are relatively small, the acoustic emission signal is used in BP neural network as a pattern of recognition. In Matlab6.5, neural network model identification is created and taking advantage of nonlinearity and the ability of learning and memory of Neural Network, this model is fixed by training structure of network with training samples. The work presented shows that acoustical emission signal processing and research on early fatigue fault diagnosis based on the wavelet and the neural network is viable.

Jan 1, 2014

By Karl J. C. Harries

"11.1. INTRODUCTIONA royalty is the most common form of interest retained by an owner who is disposing of his property or by a joint venturer who ceases, voluntarily or otherwise, to participate in the joint venture.1 Rarely does a non-participating party have a direct interest in the property and/or assets of a project, except during the period when a non-participating joint venturer may be having his interest diluted.2 In fact, it is most unwise to permit a non-participating party to have such an interest. It may give rise to significant problems that could prevent or substantially delay the development of an orebody and require a considerable amount of time, effort, and money to correct.3In negotiating a royalty, it is important to be aware that there is no law or convention that says, “You just don’t do that in a royalty agreement.” As with any agreement, inventiveness and flexibility on the part of the negotiator are not just assets, but virtual necessities. It is also for this reason that it is essential to read the royalty provisions, particularly the definitions, fully and carefully, especially if you are the recipient. On the other hand, if your inventiveness and flexibility cause your accountant to question the advisability of one of your ideas, pay close attention to him.4 He will, no doubt, have had experience with many royalties, and no competent professional adviser disparages a client’s ideas without good reason. Besides, he will probably be the person who will be determining the royalty or certifying the determination of it. At the very least, he will be auditing your general financial statements, which must, of course, reflect the royalty determination. Heeding his advice not only may make the determination easier but also will probably save you money in professional fees later on. Nevertheless, do not simply accept his comments or recommendations without understanding what they mean, why they have been made with respect to your royalty agreement (sometimes professionals have comments that they make as a matter of course and, even though they may be valid, you should require them to be justified to you), and how they will affect your royalty determination.It is surprising how many corporate payors insist that their standard royalty provisions5 be used as a matter of policy, thereby effectively tying the negotiator’s hands. It is even more surprising, and to professional advisers frightening, how many of the senior employees who insist that such a policy be adhered to, virtually without variation, do not know what is in the standard provisions and would be hard-pressed to explain them to a property owner. If standard provisions are appropriate, by all means use them, but do allow experienced and sensible negotiators some flexibility and make sure that everyone within the corporation who may have to use such provisions – negotiator and supervisor alike – knows what they contain and why they are as they are. For example, there are often good and convincing reasons to describe a deduction in a certain way or to include a certain specific type of deduction. On the other hand, quite often the answer to the question “why?” is that “it has always been there”; this is, or should be, an unacceptable answer. In any event, if you, as the negotiator, appear to know what you are talking about, are familiar and comfortable with your royalty provisions, and are backed up by your boss with the same words or reasoning, a property owner cannot help but be satisfied that you are knowledgeable, even if he still does not agree with your provisions. Finally, if you do use standard provisions, make sure that they are reviewed and updated regularly."

Jan 1, 2003

By Stephen M. Jasinski

This report describes the materials flow of mercury in the United States. It examines the mining and production of mercury and the manufacturing, uses, and ultimate disposal of mercury. Materials flowcharts were prepared for 1989 and 1990. An effort was made to include estimates for all major anthropogenic sources including fossil fuel combustion, waste incineration, and nonferrous metal mining operations. Mining and mineral processing released about 100 mt/yr of mercury to the environment in both 1989 and 1990. The combustion o ii fu1s released 175 mt/yr in the same years. The manufacturing, use, and disposal of products containing mercury accounted fix the release of 1,037 mt of mercury in 1989 and 938 mt in 1990. The manufacture of chlorine and caustic soda was a major source of recycled mercury, but it was all reused within the industry. Recovery from all waste products accounted for 36% of reported consumption in 1989 and 42% in 1990. The losses from manufacturing and end use have been declining, whereas mercury emitted from combustion sources has not been strictly regulated and will likely become the largest source of mercury releases to the environment.

Jan 1, 1994

By Mark Colwell

As per most other earth science engineering problems, the underground coal geotechnical environment and the way in which roof and rib support interacts with the rock mass are complex issues. While the problem should not be oversimplified (i.e., the dominant failure mechanisms or critical data input parameters should not be ignored), without question judicious simplification is at the heart of all good engineering design. Engineers play a vital role in supplying the world with solutions and products; however it is crucial that engineers make practical and readily useable contributions. One way to ensure this is to employ simplification in the engineering process.

By Mark Jolly, Xiaojun Dai

"Foundry engineers in the traditional foundry usually regard the quality of casting component as the most important issue and leave the energy saving or energy efficiency as the subsidiary one. This frequently causes disproportionate energy consumption as a result of the inefficient casting processes used and increases the production costs. This paper presents the novel CRIMSON aluminium casting process and compares its facility and melting process with traditional melt furnaces and aluminium alloy melting process. A real example is investigated to demonstrate quantitatively how the traditional foundry wastes energy and what the improvement of energy efficiency can be achieved using the new CRIMSON method. The results of this investigation will help the foundry engineer recognize the importance of energy saving and demonstrate how to use this new technology to reduce production costs and carbon footprint without decreasing the quality of the cast component.IntroductionAluminium melting in metal casting industry is an energy intensive process where it is estimated that the energy consumption is in the order of 1,700 ~ 4,700 kWh tonne-1 in using crucible and natural gas [1]. Different countries may use different energy resources for aluminium melting: in US the main energy resources are natural gas, electricity and coke [2] and in UK most of the foundry use electricity, gas and oil as energy resources [3]. Due to the pressure of rising energy price and the strict environment law, it is anticipated that under the right socioeconomic conditions, the efficiency optimisation of industrial process can be an important step toward increased industrial sustainability [4]. In metal casting industry the energy efficiency of a casting facility depends largely on the efficiency of its melting and heat treating performance. In association with the two performances, over 60 % of the total process energy costs are represented in a typical casting facility [5] where there are huge opportunities for metal casting industry to adopt the best energy practices for potential energy saving. How to ameliorate the current processes for increasing energy efficiency will have a vital effect on reducing the production costs and increasing the competitiveness. For instance, by implementing some state of the art technologies such as the CRIMSON method in aluminium alloy casting will make use of such opportunities."

Jan 1, 2011