Search Documents

By Jack L. Henry

The ternary system A14C3-AIN-Al203 has been examined to determine compositions which may display desirable high-temperature refractory properties. Powder methods were employed in the synthesis of all test compositions. Forming and sintering behavior was examined and hot-pressing parameters were measured. Several properties were studied for each composition of interest in the system. The properties included hydrolysis rate in moist air, elevated temperature oxidation rate, density, softening point, tensile strength, and rupture strength. In most cases equilibrium was not achieved, and the data are representative of a nonequilibrium system. Approximately 16 separate phases have been observed in the system. Forming behavior and selected properties of five compositions of interest were compared with those of aluminum oxide and aluminum nitride. None of the compositions compared favorably. Oxidation and vaporization appear to be serious drawbacks to the use of these compositions at elevated temperatures.

Jan 1, 1969

By W Frint

An area in Southwestern Wyoming is rapidly becoming the soda ash capitol of the world. Starting only 20 years ago from a unique deposit of trona, the out-put has rapidly increased until now about half of the soda ash produced in the United States comes from this area. Chemically, soda ash is sodium carbonate, a large tonnage, widely used alkali. The largest single industrial use is in glass manufacture, where 25 tons of soda ash are used in producing 100 tons of glass. Other big users are the detergent and chemical industries. The trona deposits in the Green River basin of Wyoming, were formed about 75 million years ago as part of a geologic period when an ancient lake alternately went through periods of being a large fresh water or smaller brine lake. Today these deposits lie from 800 to 3000 feet below the surface in a semi-arid, almost desert region just west of the Rocky Mountain Continental Divide at an elevation of 6200 feet. In this area there is a prevailing westerly breeze and almost every afternoon the velocity reaches very windy conditions. Rainfall is minimal, being only 6-8 inches of moisture per year with an evaporation rate exceeding 24-inches. Most of the moisture comes in winter snows or summer thunderstorms. Temperatures are low with below zero weather dur¬ing most of the winter and early morning frost is not uncommon during the summer months. There are many trona beds varying in thickness from a few inches up to 15 feet. The deposits now being mined vary from 8 to 10 feet in thickness. The ore is mined by driving tunnels either via conventional explosives or with continuous boring machines. It is transported to the shafts via conveyor belts

Jan 1, 1972

By H. E. Hilliard

The Bureau of Mines investigated hydrometallurgical procedures for concentrating precious metals from a mechanically processed metal fraction of obsolete military electronic scrap. Feed material for the leaching procedures described in this report was the high-tension-separated metal concentrate obtained as a fraction from mechanically processing partially stripped electronic units. Initial pretreatment with a 20-wt-pct-NaOH solution solubilized most of the aluminum. After washing, the resulting residue was incinerated to destroy any organics attached to metal particles. The incinerated residue was leached with 20-vol-pct H2S04 solution using two methods, countercurrent pressure and ultrasonic-aided leaching to solubilize the base metals, predominantly copper. Silver was recovered from the base metal leach residue using 50-vol-pct HN03, and gold contaminated with several percent palladium was recovered from the silver leach residue using aqua regia. The impure silver and gold plus palladium products represent about 1.5 wt pct of the high-tension-separated metal concentrate. Included is a three-step process evaluation study of mechanical processing of general electronic scrap and two hydrometallurgical procedures for leaching high-tension-separated metallic concentrates obtained from the mechanical processing step. Process evaluation concluded that only mechanical processing is economically viable.

Jan 1, 1985

By C. W., Davie

"DEFINITIONDiatomaceous earth consists almost entirely of the silicious remains of minute flowerless aquatic plants known as diatoms. The name diatomaceous earth, therefore, is to be preferred to others such as trade names, inappropriate terms, or names correctly applied to some other product. The following names should, therefore, not be used for diatomaceous earth,-- kieselguhr, infusorial earth, diatomite, celite, moler, bergnehl, English rottenstone, tripoli, tripolite, fossil earth, desmid earth, white peat, tellurine, randanite, ceyssatite, or any trade name.FORMATIONDiatoms live in practically all kinds of water, fresh or salt, hot or cold, still or running and under different conditions of depth and pressure. These minute plants assimilate inorganic salts from their environment and produce skeletons of silica much as mollusks secrete lime and form their Shalls. When the diatoms die they settle to the bottom together with anything else which may be present, such as sand, clay or volcanic ash. The organic matter gradually disappears leaving the silicious skeletons of the diatoms which, with impurities, make up the deposits of diatomaceous earth. These deposits which are still being foamed at the present time and which were produced throughout very different epochs, were more prolifically formed in the Tertiary, so that the thickest beds so far discovered are of that Age."

Nov 1, 1925

Continuous improvement in environmental management assists in the achievement of sustainability goals for the processing of minerals. The use of regular internal environmental audits (scored or unscored) which form an integral component of an Environmental Management System (EMS), provide demonstrable evidence of this improvement. Case studies are presented for a number of major coal mines in the Hunter Valley, where regular internal environmental audits have been undertaken every two to three months, over periods varying from 18 months to five years. Examples of the benefits of improved environmental performance (driven by the audit process) to sustainable development are provided.The auditing process as described here for coal mines, and coal handling and preparation plants, is equally applicable to the processing of other mineral ores, metalliferous mines, quarries, and oil and gas projects.

Jan 1, 2004

By B W. Ham

The legacy of underground coal mining may be a land surface which, in parts, may be unstable in the long term. A case study analysis has been undertaken to explain some of the hazards and how the risk may be assessed and managed.The Ipswich Coal Measures were extensively mined with shallow underground workings, which now underlie a number of suburbs in the eastern side of the city of Ipswich in south eastern Queensland. The area was subject to underground mining from the 1840s to 1997. In general, the mines were small, family-owned operations that were restricted by complex geology, interactions with neighbouring operations and ownership of surface facilities. The oldest available mine plans date back to the late 1890s.The residents in these mining areas have a long history of unexpected mining subsidence events. A level of risk management for property owners has been implemented by the Ipswich City Council, which requires a mining subsidence risk assessment to be submitted as part of building applications for property development in the areas suspected of having mining subsidence risk. This discussion examines a series of generic subsidence events and how the risk may be assessed and managed and the hazard controlled.CITATION:Ham, B?W, 2014. The legacy of underground coal mining – mine subsidence: Ipswich coal measures case study, in Proceedings Life-of-Mine 2014 , pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D. Duff, R. A. Cameron, R. E. S. Whitehead

"Although CO2 content indicates the quantity of carbonate in altered basaltic rocks, it does not measure the intensity of carbonate alteration. CO/CaO molar ratios, which correlate with the relative proportions of individual carbonate species, measure the intensity of carbonatization. The Timmins gold area is characterized by pervasive carbonatization, with large parts of the area having CO2/Ca0 ratios greater than 1, representing C02 supersaturation relative to CaO. The mean CO/CaO in the Timmins area is0.67, compared to 0.13 in two unmineralized control areas. Regional arsenic abundance in the gold-bearing area averages 4 ppm, compared to about 0.35 ppm for the non-mineralized areas. The average K20 and Rb abundances are similar in both mineralized and non-mineralized areas (about 0.30% K20 and 7 ppm Rb). Although there appears to have been no wholesale addition of K20 or Rb to the mineralized area from external sources, these alkalies have been redistributed internally, resulting in patterns of local enrichments and depletions which are characteristic of the mineralized region.Local target anomalies associated with known mineralization consist of CO2/Ca0 > 1.5, As > 10 ppm and K2O > 0. 75%. Not all three values are required to be above these thresholds in order to identify local targets. Combinations such as C02/ Ca0 > 1.5 and As < 10 ppm, CO/CaO 1-1.5 and K20 > 0. 75 or K20 > 0. 75 and As > 10 ppm are equally indicative of proximity to gold occurrences. Gold-bearing veins and associated anomalies occur throughout the entire volcanic succession and are not restricted to any particular stratigraphic horizons. The levels and patterns of alteration and occurrences of gold appear to be structurally controlled."

Jan 1, 1982

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017

By Robert B. Hoekzema

This Bureau of Mines report describes the history, characteristics, distribution, and mineral development potential of 21 lode gold deposits in or near the Chugach National Forest (CNF), AK. It includes findings from a 4-yr (1979 to 1982) mineral evaluation of the CNF conducted by the Bureau and the U.S. Geological Survey (USGS). This evaluation, undertaken to provide the U.S. Forest Service with mineral resource data for use in making decisions on land use, included site-specific mapping and sampling of more than 200-lode gold deposits. The data presented here were compiled from the findings of this 4-yr evaluation and from existing literature. Fourteen of the 21 lode gold deposits described in this report contain a combined identified resource of 117,750 short tons (st) averaging 0.55 oz/st Au and 0.2 oz/st Ag. Two mineralized felsic dikes in the Summit Lake-Palmer Creek area contain a combined identified resource of 18 million st grading 0.02 oz/st Au and 0.16 oz/st Ag. Identified resources were not determined for the remaining five deposits because of a lack of information.

Jan 1, 1987

By J. D. Davis

THIS REPORT gives results of an investi¬gation of the carbonizing properties of coals from Pittsburgh bed, Jamison No. 9 mine, Marion County, W. Va., and from Upper Freeport bed, Bull Run No. 1 mine, Preston County, W. Va. The study included Bureau of Mines-American Gas Association tests at 800° and 900° C. and various chemical and physical tests designed to evaluate the plastic, expanding, and agglutinating properties of coal. A blend of each coal was carbonized in the 500-pound slot oven. The carbonization sample of Pittsburgh coal contained 2.7 percent moisture, 35.8 percent volatile matter, 54.4 percent fixed carbon, 7.1 percent ash, and 0.9 percent sulfur. It contained 60.9 percent fixed carbon on the dry, mineral-matter-free basis and had a heating value of 14,780 B. t. u. per pound on the moist, mineral-matter-free basis. It therefore ranks as high-volatile A bituminous and was blended with low-volatile Pocahontas No. 3 coal. Upper Freeport coal contained 2.8 percent moisture, 27.7 percent volatile matter, 60.9 percent fixed carbon, 8.6 percent ash, and 1.0 percent sulfur, as carbonized. It contained 69.5 percent fixed carbon on the dry, mineral-matter-free basis and therefore ranks as medium-volatile bituminous. It was blended with high-volatile A Pittsburgh coal from Allegheny County Pa.

Jan 1, 1952

By B E. McCarthy

Red Dome Mine was a highly complex gold copper operation developed over a number of phases between mid-1986 to October 1997. With only three years of production ahead at any time, a proactive practical approach to mine closure was necessary. In 1989 the Domains Concept to life-of-mine planning and mine closure was created as a response to the proposed changes to legislation.The Domains Concept, a relatively simple idea developed to integrate mine closure during production at Red Dome, has been broadly adopted by both government agencies and industry in the intervening 20 year period. Over time the author has observed that the concept has been poorly applied, misunderstood and in some cases even misrepresented. As a consequence, the potential opportunities from applying the concept, including the optimisation and minimisation of life-of-mine costs, mitigation of long-term financial liability exposures and building credibility with the general community, have been missed.This paper examines the many benefits, advantages, applications and perceived barriers to developing and integrating a fully costed life-of-mine plan. Integrating the Domains Concept early in the project, within the operational budgeting, allows the production of a meaningful and useful document, representative of a whole life-of-mine, cradle to grave, with measurable rehabilitation and closure outcomes when the concept is used to full effect.The Domains Concept serves to optimise cost-effective, whole of mine, life cycle planning which provides beneficial outcomes for the community, significantly mitigates legacy issues and contributes to the attainment of compliance and sustainability principle objectives.CITATION:McCarthy, B E, 2014. The domains concept – 20 years on retrospective, obstacles and opportunities for effective life-of-mine implementation, in Proceedings Life-of-Mine 2014 , pp 621–636 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D. A. Elkins

This report is the second of a series of three that will evaluate, in order, the metallothermic, carbothermic, and electrolytic methods of magnesium production. The historical development of the carbothermic process is outlined. Production costs varying from 38.9 to 21.8 cents per pound of magnesium are estimated for different versions of the process. Additional suggested process modifications are listed. The technical and economic potential of the different versions are compared. Areas deemed most promising for future research on the process are delineated.

Jan 1, 1967

By Robert S. Becker

The results of a laboratory investigation of coal cutting mechanics and noise is presented. These experiments were performed using a linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts is ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to Formulate analytical models of the coal cutting forces and noise. The analytical model For coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator&apos;s position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as Provide benefits to other important areas of underground health and safety.

Jan 1, 1980

By Carlos Frias

The lead-acid battery recycling is a major industrial activity (more than four million tonnes recycled lead per year) that generates large amounts of toxic wastes such as lead slag, mattes and acidic sludge, besides airborne emissions. This is a waste-producer industry that needs a definitive solution to avoid its negative environmental impact and getting a sustainable lead production. That is the principal target of the CLEANLEAD technology, which properly combines both hydrometallurgical and pyrometallurgical routes aiming to get zero-waste production, reducing the use of energy and resources in all phases of battery reprocessing, and consequently, greatly decreasing the operating cost. There will be no toxic emissions to land, water or air, and obtained products are pure lead metal or pure lead oxide, and commercial gypsum instead of waste sludge.

Jan 1, 2006

By G. L. Oldright

The studies previously made on Smelting in the Lead Blast Furnace have dealt with the custom smelter of the International Smelting Co. at Tooele, Utah, and on the smelter of the Bunker Hill & Sullivan Mining & Smelting Co. at Kellogg, Idaho. The International plant may be considered representative of the traditional custom smelter. The lead smelter of the future seemingly will have to treat increasingly richer lead charges. This feature was then stressed in describing the Bunker Hill plant.

Jan 1, 1934

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

By W. J. Fene, R. D. Currie

The value of protective clothing in the prevention of injuries has long been recognized in many of the leading industries , but the adoption of the idea into mine safety programs is comparatively new . Once started , however , the idea has grown rapidly and the results already obtained by mining companies have shown that it is fundamentally sound . Both coal and metal mining companies are rapidly adopting these protective measures , and since 1924 many mines have become well equipped with eye , head , and foot protection . At the present time approximately 70 percent of the employees in the anthracite mines of Pennsylvania are provided with safety hats . At many metal mines all employees are provided with safety hats, shoes , and goggles . The Pennsylvania mining law provides that all shaft · workers in anthracite mines shall wear protective hats . In According to a study³ made of the nature of 3,485 temporary injuries and of the parts of the body of underground coal mine employees most exposed to occupational hazards , the head and face were injured 665 times , the hands 856 times , and the feet 565 times . Of 2,555 temporary injuries in metal mines , the head and face received 484 , the hands 788 , and the feet 357 . a similar study4 made by a coal -mining company for the year 1928 , of 556 injuries the scalp received 9 , the skull. 4 , the eyes 47 , the hands 62 , the thumbs 21 , the fingers 141 , the ankle , the feet 51 , and the toes 35 . Probably most of these injuries could have been prevented by suitable protective clothing and equipment . This study also revealed that at least one injury occurred

Jun 1, 1933

Many mining companies aim to integrate sustainability principles into their new projects. There is an intention for improvement, but frequently this results in little more than &apos;business as usual&apos; projects that retrospectively categorise controls for environmental and social risks as sustainability initiatives as part of a public relations exercise. The successful implementation of sustainability requires a change of mind-set and behaviours at an organisational and personal level. In addition, sustainability incorporates a very wide range of interests and technical disciplines. One of the key challenges is in understanding how and when to pull these diverse threads together within a project or organisational process. This paper will explore a number of themes: What does it mean to implement a project in accordance with sustainability principles? How far beyond &apos;business as usual&apos; is it reasonable to go, and what is the business case for this? Why do the intentions for sustainability sometimes fail and how can we prevent this happening in future? People are instrumental in delivering sustainability; how do we embed sustainability thinking into their behaviours and decision-making? The approaches that have been taken to integrating sustainability in design; what has and has not worked and some of the barriers to integrating sustainability into design? The authors will discuss these themes drawing on case studies from URS&apos; experience in integrating sustainability into large projects. The authors will discuss the need for: a strategic approach which provides a simple framework for tactical decision-making and the consequences of taking tactical decisions in the absence of this framework, alignment of the project team and promotion of a culture of innovation, a shift from a risk/compliance mentality to an opportunity identification mindset, and a systematic approach to integrating sustainability into project design processes.

Jun 1, 2010

By K. Chomyn, R. Veenstra, P. Zangeneh, Hatch Ltd., C. Van der Woude, H. Ghorbani

"The furnace is the heart of smelting operations, and therefore the performance, reliability, and campaign life of the furnace are critical considerations. Furnace refractory is exposed to high temperatures and other harsh operating conditions causing brick erosion, crushing, and cracking, typically limiting the furnace campaign life and requiring costly furnace shut-downs for refractory re-lining. Despite extensive study, the in-service thermal / mechanical stresses in these complex refractory systems are not generally well understood. Hatch has developed a thermal-mechanical finite element analysis (FEA) based furnace refractory modeling approach that allows for the quantification of refractory movements, load distribution, and thermal / mechanical stresses.Due to the complexity of the refractory system, a range of models are used to identify and assess damage mechanisms and design improvements, including: 2D models, to capture expansion and movement of individual bricks, changes to load paths, and thermal stresses; and 3D models, to include the effect of differential expansion between bricks in each course, and assess overall load distributions. The 2D and 3D analyses include the effect of nonlinear temperature-dependent properties, thermal expansion, movement of individual bricks with frictional contacts (i.e., gaps can open, bricks can slide), and brick tensile or compressive failure. Both as-built and damaged conditions can be investigated (e.g., after bath zone brick erosion), for circular and rectangular furnaces. 3D models also include papering and brick joint & interface action.Analyses using these models have shown the importance of thermal stresses, papering, and geometry / arrangement of individual bricks. Results have been used to identify and assess damage mechanisms, showing good alignment with furnace autopsy observations. By using this FEA-based approach to quantify the refractory design, the risk of damage can be significantly reduced, low-cost design changes can be identified, and the furnace campaign life can be extended.INTRODUCTIONThe furnace is the heart of smelting operations and therefore the performance, reliability, and campaign life of the furnace are critical to the success of the smelting operation. Furnaces are inherently exposed to high temperatures, often in excess of 1600°C (Holappa, 2004), and furnace operating power has progressively increased over time (Voermann, Gerritsen, Candy, Stober, & Matyas, 2004). The refractory system must withstand high temperature, high heat flux, and other harsh operating conditions. These conditions are particularly significant for the furnace hearth, and can lead to damage including brick erosion due to molten material flows, crushing due to thermal expansion loads, and cracking due to severe thermal gradients within the bricks. Refractory damage typically limits the furnace campaign life, requiring costly furnace shut-downs for refractory re-lining (repair or replacement). In some cases the refractory may lose integrity causing damage to nearby equipment and harm to personnel."

Jan 1, 2016

By D. M. C. Valbom

The introduction of new diamond sorting technologies as well as additional manufacturers I vendors, has increased the equipment selection and combinations available for recovery flowsheet design. This paper describes the methodology used and the benefits realized in the design of recovery plants by ensuring a fundamental understanding of the advantages and limitations of the technology embodied in the equipment, a comprehensive knowledge of the ore body characteristics, and the effective matching of this information in combination with operational commercial requirements.

Jan 1, 2010