Search Documents

By John J. Simmons

There is considerable interest in the iron and steel industry in the development of technologies that can reduce carbon dioxide emissions, as the iron and steel industry is the third largest producer of carbon emissions in the world, after automobiles and the power generation industry. The E-Iron Iron Nugget Making Process, invented by Dr. Komar Kawatra and Dr. Tim Eisele, provided a major breakthrough in the iron making process as the process uses biomass in the form of hard wood or soft wood as the reductant in the place of coal. Dr. Kawatra recognized that biomass is rich in both carbon monoxide and hydrogen, two important reducing agents. This resulted in initial experiments conducted by Dr. Kawatra and Dr. Eisele in the laboratories of the Chemical Engineering Department of Michigan Technological University (Michigan Tech) that prepared self-reducing pellets with wheat flour as the reductant and limestone/dolomite as the flux. Initial results were encouraging so they extended their work to include hardwood, which is in huge supply in the forests of Michigan and Minnesota, as the reductant. Dr. Kawatra has also applied the E-Iron Technology to other iron bearing minerals to produce pig iron grade iron nuggets. He used the E-Iron Process to convert red mud, a high iron waste product of the aluminum industry, into pig iron nuggets with the rare earth elements reporting to the slag. This work resulted in a patent with Dr. Kawatra and Dr. Michael Archambeau named as the inventors. Dr. Kawatra then extracted the rare earth elements as a separate high value bi-product using oxalic acid, which he produced from carbon dioxide. Dr. Kawatra also conducted a test program that produced pig iron nuggets from New Zealand beach sands. The vanadium in the beach sands was retained in the iron nuggets, recoverable as a valuable bi- product in a separate process. The titanium dioxide in the beach sands reported to the slag. This demonstrates the potential use of the E-Iron Process to convert the large ilmenite reserves in Northern Minnesota into pig iron and titanium dioxide. Another use of the E-Iron Process discovered by Dr. Kawatra was its ability to produce iron nuggets from manganiferous ores. Dr. Kawatra was able to direct the manganese into either the metal or slag by adjusting process temperature. The above discoveries are included in several patents that were assigned to Carbontec Energy. This presentation will only address the use of the E-Iron Process to produce pig iron nuggets from steel mill waste and un-pelletized, mid-grade iron ore. Carbontec Energy Corporation agreed to sponsor additional research directed at improving this new technology that would later be trade named, The E-Iron Process. Carbontec Energy conducted further work that proved that the E-Iron technology could also convert steel mill waste into metallurgically acceptable iron nuggets. Carbontec also collaborated with the Lawrence Livermore National Laboratory and Purdue University Northwest to conduct a Department of Energy (DOE) sponsored program that would use their high performance computer capability to both verify and model the E-Iron Process. Purdue University Northwest reported that the E-Iron Process can produce pig iron nuggets with 85% less carbon emissions than a blast furnace. The E-Iron Process is similar to the ITmK3 process, developed by Kobe Steel, that also produces iron nuggets but uses coal as the reductant.

Feb 1, 2025

This appendix contains the list of equipment selected for the capitol cost estimate, with the respective quotations from their vendors/manufacturers. A vendor response report along with a separate equipment and motor list has been included in the first part of this appendix.

Jan 1, 1979

By Arno C. Fieldner

The objectives of the coal-research activities of the Bureau of Mines are very well expressed in the organic act of Congress establishing the Bureau. It reads as follows: That it shall be the province and duty of the Bureau of Mines, subject to the approval of the Secretary of the Interior, to conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources, through the prevention of waste in the mining, quarrying, metallurgical and other mineral industries; to investigate explosives and peat; and on behalf of the Government to investigate the mineral fuels and unfinished mineral products belonging to, or for the use of, the United States, with a view to their more efficient mining, preparation, treatment, and use; and to disseminate information concerning these subjects in such a manner as will best carry out the purposes of this act.

Jan 1, 1946

By Joseph Sofra

It has become increasingly evident that sustainable metals production in the 21st century requires producers to balance the needs of cost effective, high value production with that of responsible plant operation. This is becoming more difficult as lower grade and more complex feed materials, including recycled scrap and residues, are being processed to reduce production costs and decrease exposure to primary metal market fluctuations. One particular facet of the metals industry facing these challenges in the 21st century are copper producers, The recent steady decline in the copper price has seen the industry cut expenditure, tighten control on income streams and focus on high returns on capital investment. For these reasons copper producers are looking towards flexible technologies that can deliver high value products, with minimal environmental impact at low capital and low sustainable operating costs. Ausmelt's Top Submerged Lancing (TSL) technology for copper production is a low cost, proven technology for the processing of both primary and secondary copper materials. Both the smelting and converting operations introduce significant advantages in environmental performance, improved process efficiencies and high rates of metal recovery, Ausmelt has made significant gains in the past 4 years in establishing a strong market position for its copper technology, New installations in China, South Africa and India as well as existing operations in Zimbabwe and China have demonstrated its effectiveness. This paper reviews the application of Ausmelt Technology for both smelting and converting of primary and secondary sources, It discusses Ausmelt's design and implementation philosophy, and how this philosophy meshes with the needs of the end user.

Jan 1, 2003

By P J. Jacobs

FORACO is the third-largest global drilling services company, and recently celebrated its 50th anniversary. The company’s historical roots are in French-speaking West Africa, delivering hydrogeological drilling services to resource companies, villages and regional centres. Today, FORACO operates over 300 drill rigs in more than 20 countries.The Asia Pacific region of FORACO runs a fleet of 37 late model drilling rigs servicing the diamond drilling, reverse circulation, coal, coal seam gas and hydro drilling sectors.FORACO Australia has extensive experience delivering large diameter coring (LDC) samples to the resource community. In the past three years, the company has been involved in six 8? coring projects in a variety of geographies and geologies, including iron ore, coal and uranium. FORACO has developed proprietary equipment and techniques to deliver cost-effective LDC samples with outstanding core recovery.The FORACO LDC sampling system is hands free, with mechanised rod and corebarrel handing to minimise the risk of manual handling injuries. Sample volumes are six times PQ (the common industry standard for large core samples), with core recoveries consistently above 96 per cent in extremely difficult formations.Eight inch coring is a conventional coring system suited to hole depths up to 150 m. For deeper applications, FORACO has recently invested over $4 M in a 6? wireline coring system capable of achieving depths of 300 m.CITATION:Jacobs, P J, 2014. Large diameter core sampling, in Proceedings Sampling 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

In spite of the efforts done in the past to implement in Codelco best practice guidelines and standards on several important sampling, assaying and variability issues, many people, particularly top managers and operators, are still not aware of the relevance of the use of the principles and practice of geostatistics, sampling theory, analytical chemistry and the understanding of processes variability from rock to cathodes. As a result, an important challenge for the sampling community is to find out the causes of this lack of awareness and to develop communication skills to influence the organisation, particularly the top management level. This situation is not affecting only Codelco; it is a common characteristic of the copper mining industry. The main cause is cultural. Judeo-Christian and occidental sciences are deterministic. This implies a disregard of process variation and the assumption that homogeneity is omnipresent. Another important aspect of the cultural challenge is education. Education is the most efficient way to transfer a system of ideas, traditions and practices. To implement proper courses of sampling theory and geostatistics and support to multidisciplinary education at universities, mining companies will improve teamwork between geologists, mining engineers, metallurgists and chemists. The improvements will imply a more sustainable and efficient mining business.

Mar 1, 2010

By J. P. Ress

In 1903, seventeen years after mining of the Witwatersrand gold-bearing reefs started, the findings erf the Miners' Phthisis Commission (Transvaal) resulted in the initiation of measures with the object of controlling dust production. The substance of these measures was as follows: Removal of persons from places where they would be exposed to blasting fumes; use of water to suppress dust made in drilling and in other operations; supply and control of air to working-places; filtration of dusty air; and determination of the amount of the dust in the air. Broadly speaking, progress in dust control has followed these four lines with increasing success as the nature of the problem has become better known. Complete success has not, however, been achieved, partly because increasing mechanization of mining has intensified the problem and partly because the application of these measures is not infallible, being subject, in many cases, to human control. A brief summary of the development of these measures will lead to a description of present-day practice.

Jan 1, 1947

By Herbert H. Einstein

Swelling ground is one of the most feared problem in tunneling. Although usually not causing sudden failures during construction, the very large and long- lasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners of up to 1 m that have been cracked or crushed, tunnel inverts that are heaving at a rate of 0.1 m per week during construction and continue to heave during decades. This author (Einstein (1979). Einstein et al. (1972) (1975)) and others (Huller (19761, Grob (1972) (1976). Golta (1967), tienke (19761, Krause (1976). Lee et al. (1976)) have described many cases of swelling tunnels that illustrate the significance and magnitude of the problem. This paper intends to show that tunnels in swelling rock can be built to perform satisfactorily. . For this purpose the tunnel builder needs to know how to determine the existence and specific behavior of swelling ground, how to select appropriate structural characteristics of the tunnel and predict its performance under the specific ground conditions, and finally how to construct the tunnel such that the anticipated performance will be achieved. This concept of a design-construction procedure is the same as that for tunneling in general; it is mentioned here for NO reasons: 1. To point out that design and construction cannot and should not be separated. The way in which the tunnel will be built has to be an integral part of the design. 2. This paper will be structured corresponding to the procedural concept.

Jan 1, 1981

By Donald McLaughlin

INCREASING variety of interests among mining geologists is becoming more and more marked, as the frontier of their science and of its applications continues to expand. Each of the traditional lines of inquiry provides its crop of new and better defined problems, and answers to them are being found in far more precise terms than in the past as older uncertainties .are swept away with the sharper techniques and the even sharper ideas of modern geology. A glance over the assemblage of projects and publications in 1939 reveals conspicuous activity in many different parts of the front, such as the attack on the controversial question of the acid or alkaline character of ore-forming solutions, the place of mineral districts in the larger structural framework of continents, and the place of ore shoots in the local patterns of districts. Instructive comparisons are being made which cut across lines of older correlations or which reinforce them by pointing out heretofore ne-

Jan 1, 1940

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By D. M. Schubert

As a clean and renewable energy carrier, hydrogen is an important component of most alternative energy portfolios. Hydrogen combines very high energy content by weight with excellent environmental attributes. Since hydrogen reacts with oxygen to produce only water with release of energy, it can be used to power fuel cells, combustion engines, and turbines, without production of greenhouse gases at point of use. However, because of its low volumetric density, storing pure hydrogen is impractical. Thus implementation of hydrogen technologies requires materials that can safely store and release large amounts of hydrogen (1,2). In recent years, the U.S. Department of Energy (DOE) and other governmental agencies around the world sponsored extensive research on hydrogen storage materials, including those based on boron. These efforts have resulted in significant advances in hydrogen storage technologies. Boron materials stand out as leading candidates for hydrogen storage among the many options investigated. Combining excellent hydrogen densities, release rates, and safety characteristics, some boron materials can hold substantially more hydrogen by weight and volume than even pure liquid hydrogen (3-5).

Jan 1, 2010

By Sam Warren, Antonio Marinucci, Genesis Z. Figueroa, Anne Lemnitzer

Drilled Displacement Piles (DDP) provide an ideal deep foundation solution that combines the benefits of ground improvement with traditional advantages of piling systems. This paper consolidates data from 20 construction projects in which more than 30 DDPs were installed and tested axially. High quality site exploration data (e.g., Cone Penetration Test and Standard Penetration Test) were evaluated to derive geotechnical analysis parameters. The test sites consisted of mostly mixed soil types with strongly stratified layers of sand, silt, and clay. Pile diameters ranged between 40 cm and 61 cm. Test results were compared with predictive methods developed specifically for DDPs as well as methods used in general geotechnical practice. The accuracy of the empirical methods is presented in terms of total pile capacity, pile length/diameter, and soil type. The large majority of all examined methods underpredict the in-situ pile capacities. It was also found that the difference between the tested and predicted capacity is strongly related to the level of improvement in the surrounding soil due to the piles’ installation. A general comparison between predictive axial accuracy and the observed level of ground improvement upon installation is also discussed.

May 1, 2022

By A Lechner, T Baumgartl, S Arnold, P Audet

When revegetation is a part of a rehabilitation strategy at mine sites in arid and semi-arid environments, its success can be strongly affected by the availability of water prior or during the time of seed dormancy, germination and early growth of seedlings. The semi-arid and arid environments of northern Australia are characterised by highly variable and erratic rainfall and hence the actual weather conditions at and around the time of germination and seedling emergence play a critical role in determining the success of plant establishment and the type of plant community that may develop.Using available climate data, an analysis has been undertaken and a set of indices has been developed which describe the suitability of the climatic conditions for rehabilitation. In total, eight sites from Queensland and one site from New South Wales, Australia have been analysed. It could be determined that regular rainfall and relatively short periods of water-deficit are key characteristics of climate suitability. A comparison of the locations studied allowed the separation into suitable and susceptible locations in terms of the availability of water, amount of rain and duration of drought between rain events.In our experience, specific estimates of climate suitability are rarely incorporated into the design of mined land rehabilitation programs. We consider that the regional intensity, seasonality and extremity of climate represent an overarching component of landscape complexity, which in turn will influence the development of post-disturbance ecosystems in these regions. This paper presents the outcome of climate analyses paired with the development of suitability indices. A conceptual framework is presented explaining the suitability matrix and its incorporation as a prognosis tool to achieve greater certainty for success in rehabilitation development.CITATION:Baumgartl, T, Arnold, S, Audet, P and Lechner, A, 2014. Development of climate-based suitability indices for the improvement of success in rehabilitation, in Proceedings Life-of-Mine 2014 , pp 483–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Jonathan G. Price

The 2011 report titled ?Energy Critical Elements: Securing Materials for Emerging Technologies? by the American Physical Society?s Panel on Public Affairs and the Materials Research Society surveys potential constraints on the availability of these elements and identifies five specific areas of potential action by the United States to ensure their availability: 1) federal agency coordination; 2) information collection, analysis and dissemination; 3) research, development and workforce enhancement; 4) efficient use of materials and 5) market interventions. Energy-critical elements (ECEs) are a class of chemical elements that currently are critical to one or more new energy-related technologies. A shortage of these elements would significantly inhibit large-scale deployment, which could otherwise be capable of transforming the way in which energy is produced, transmitted, stored or conserved. The report addresses elements that have not been widely extracted, traded or used in the past, and therefore are not the focus of well-established and relatively stable markets (such as carbon in coal or uranium as fuels, copper, aluminum, nickel and iron, all of which are clearly vital in energy applications).

Jan 1, 2011

On April 5, the potlines at Consolidated Aluminum Corp.'s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

By Yasuo Iizuka

We have had studied CO oxidation on unsupported Au powder (mean particle size, ca.100nm) manufactured by evaporating ultra high purity gold metal (>99.99%) in inert gas and reported that it showed some activity after oxidizing pretreatment in O2 at 423 K?453 K. However, recent XPS analysis of the Au powder revealed that it contains much amount of impurity metals such as Ag and In at levels which far exceed those expected from the impurity level of raw gold metal in the bulk. Several samples of Au powder containing different amount of impurity metals were prepared to examine whether the activity depends upon the existence of surface impurity or not. Activity measurements were performed at 273 K after undergoing the powder under various pretreatment conditions. Although the activity of Au powder varied to some extent according to the pretreatment condition, it is strongly correlated to the surface concentration of Ag. Such dependence was not found for In, indicating that the activity of unsupported Au powder is mainly due to the existence of Ag in the surface layer. The activity attributable to ?particle size effect? was not recognized for Au powder with a mean particle size larger than 80 nm.

Oct 1, 2003

By H. Arima

The Akita Zinc Company is the only refinery which produces hematite from the iron content in the zinc leach residue. The Akita Hematite Process consists of five stages, which are SO2 pressure leaching, the first neutralization stage, the de-arsenic process, the second neutralization stage and pressure hematite precipitation. In order to strengthen its cost competitiveness and stabilize its operation, the Akita Hematite Process has been modified continuously. Most recently, two process modifications were carried out. The first was an improved ability to maintain a lower arsenic concentration in the de-arsenic process, and the second was an increased throughput in the hematite precipitation autoclave. The details of these recent changes in the Akita Hematite Process are presented in this paper.

Jan 1, 2006

By Ben Bowman

For certain ferroalloy furnaces, such as ferrochrome or ferromanganese, there is still doubt about the mechanisms operating under the electrode tips. In this paper a model is built that does not call upon an arc. The medium is best described as an electrically conducting slurry, a mixture of liquids, solids and gas. There are two sources of propulsion, the Lorentz force within the conducting part and buoyancy generated by CO bubbles, creating two opposed poloidal circulation loops, downward below the electrode axis and upward further out.

Jan 1, 2014

By Li Qihou, Li Yuhu, Liu Zhihong, Liu Zhiyong, Yang Xiaofeng

Scorodite samples were synthesized, in adding or without crystal seed respectively by using Atmospheric Scorodite Process (ASP), Hydrothermal Scorodite Process (HSP), and Improved Atmospheric Scorodite Process (IASP) individually; and their crystal structure, crystallinity, morphology, particle size, specific surface area, Fe/As mole ratio, as well as the leaching stability were characterized, aimed to reveal the relationships among the synthesis methods, the compositional and structural properties, and the leaching stabilities of scorodite. The results show that synthesis methods have significant effects on the compositional and structural properties of scorodite. Scorodite samples of high crystallinity, small specific surface area, and low Fe/As mole ratio, possess high leaching stability. The order in the leaching stability of scorodite samples synthesized in this study is as follow: ASP<HSP<IASP. Scorodite particles in the sample synthesized by IASP without crystal seed are in large sizes and of pyramidal morphology enclosed mainly by crystal planes of {111}; and the sample possesses the crystallinity of 84.5%, the particle size (D50) of 28.2 m, the BET specific surface area of 3.72 m2/g, and the Fe/As mole ratio of 1.05; after leaching this sample by using acetate buffer solution of pH 4.95 for 10 days, the total arsenic concentration in the leaching solution is merely 1.14 mg/L.

Jan 1, 2015

By S. Seetharaman

In the processing of molten metals, it is extremely important to monitor continuously the concentration levels of various minor elements, In the production of common metals like copper, iron and aluminium electrochemical sensors involving solid, as well as liquid electrolytes are being increasingly used to measure the concentrations of minor elements The present paper deals with the electrochemical principles underlying these measurements and the possible errors involved. One of the major difficulties in the case of the solid electrolytes is to correct for the consequences oldie electronic contribution to the conduction of the electrolyte. The application of the electrochemical sensors for molten metals processing involves designing of these probes to withstand the industrial operating conditions. In this respect, significant achievements have been made with respect to the design of oxygen probes for liquid metals in general and liquid copper in particular. Some of the salient design features are discussed in the paper, The application of auxiliary electrodes for impurities in molten metals like phosphorus in copper and silicon in iron are taken up. The development of oxygen sensors for slags is given special attention. Recent developments&apos; in the field of sensor technology, as applied to metals processing are highlighted.

Jan 1, 1996