Search Documents

By G. B. Shea

"In 1928, there were 47 fatal accidents in the California petroleum industry, 14.6 per cent more than occurred in 1927 when 41 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. This increase in the number of fatal accidents for 1928 has caused the first upward trend in the fatality curve of the California petroleum industry since 1923. In no other year during the 6-year period have the fatalities in any one year been greater than those for the preceding year. This fact should be given serious consideration and study by the petroleum industry, and an endeavor should be made to cause the number of fatalities again to decrease and conform to the previous gradual declining trend of the fatality curve.The following chart shows the trend of fatal accidents during the past six years:Of the 47 fatalities in 1928, 30 occurred in the drilling and producing division, 1 in the pipe line and transportation division, 14 in the refining division, and 2 in the sales and marketing division. A comparison of the number of fatalities in each division for 1927, and 1928, is given in the following table:3"

Sep 1, 1929

By Bill Linville

Producing oil, gas, and coal in sufficient amounts to satisfy U.S. demands for fuels, electrical power, and chemicals promises to be one of the country's major challenges during the 1970's. Adding significantly to this challenge is the urgent task of satisfying soaring fuel and power demands without destroying the natural environment or jeopardizing long-range requirements for resources. The Bureau of Mines, U.S. Department of the Interior, is engaged in a comprehensive program of research to help industry meet this challenge. This report reviews the aims of the research program and accomplishments in 1970; the first 11 sections cover coal programs, nine sect ions are then devoted to petroleum, and the concluding five sections deal with oil shale research. Figure 1 shows the nationwide distribution of Bureau of Mines energy research installations; Full addresses are given in appendix A. Many of the publications resulting from the Bureau?s energy research efforts are discussed throughout the report; others are listed in appendix B.

Jan 1, 1971

By William F. Hahn

The Bureau Of Mines recognized the desireability of illuminating working places in trona mines. This report describes two illumination system designs, their demonstration and evaluation on a Jeffrey 120HR continuous mining machine in an active working trona mine in Wyoming.

Jan 1, 1980

By Gerald M. Bandholz

Exxon Minerals Company, a division of Exxon Corporation, has been exploring for base metal deposits in the Precambrian volcanic rocks in northern Wisconsin since 1970. Aerial electromagnetic surveys of the area, conducted in 1974, reported an anomaly, near Crandon, in Forest County. In the summer of 1975, the first diamond drill entered the anomaly, representing the 25th prospect Exxon had drilled in Wisconsin. This first hole revealed significant mineralization containing zinc and copper. Subsequent drilling confirmed the discovery of a sizeable zinc-copper massive sulfide are body. 1.1.2 Location The deposit is located in northeastern Wisconsin within a topographical high called the Northern Highlands region. The deposit lies about 5 miles directly south of Crandon and about 2 miles east of State Highway 55 on Sand Lake Road (see fig. 1). Other local communities include Rhinelander 28 miles west, Antigo 45 miles south, and Iron River and Iron Mountain, in Michigan, 75 and 44 miles east and north of Crandon respectively. In relation to the lakes and streams, the deposit lies 0.25 miles north of Little Sand Lake, and about 1 mile south of Swamp Creek.

Jan 1, 1981

By Wendell L. Reich

Percussion drilling dates back to the hand operated star drill and hammer. Eventually steam and compressed air were substituted for muscle power and the mechanical percussion drill was born. From the hand held jack hammers, driving a forged steel bit into the rock, there evolved the jack leg, the rubber tired and crawler mounted drill carrier with automatic feed, increasing power and reducing man?s muscle requirements. Because the reaction of a blow on one end of a piece of steel has to be transmitted to the other end there is a limit to the depth or length of drill steel that can economically be used in out of the hole percussion devices. During the late 1800?s there is evidence that designers were attempting to put the percussion tool at the bottom of the hole, directly on the bit, in order to avoid the long drill steel which absorbed much of the blow, leaving little to be applied to the bit and the rock being drilled.

Jan 1, 1972

By John D. Spencer

Air and water pollution and land reclamation relating to coal mining and utilization continued to be featured in research and technologic work on coal by the Bureau of Mines in 1967. Details of the environmental studies are given in this report, along with accounts of other research relating to the mining and utilization of coal. Other studies that were continued during 1967 included health and safety, mine explosives, coal preparation and transportation, coal utilization processes, chemistry and properties of coal, inspection and analysis, and inter-national activities. Publications issued in 1967 are cited throughout the report and in appendix C. Bureau of Mines research centers and laboratories are listed in appendix A, and organizations contributing to or cooperating in the work, in appendix B.

Jan 1, 1968

By Arvind Thekdi, Cynthia Belt2

"Waste heat from industrial operations in metals industry represents 20% to 50% of the total energy used in most manufacturing plants. Reduction and recovery of waste heat offers the most attractive and cost effective method of reducing energy intensity for an industrial plant to meet corporate energy saving goals. It is possible to reduce or recover 30% to 60% of the available waste heat by using conventional and readily available technologies. Projects to reduce or recovery waste heat may offer less than 3 years payback to as short as a few months. This paper presents information on most commonly used methods for waste heat reduction and recovery in the metals industry operations. It describes the methods and use of analysis tools that would allow a user to estimate energy savings, CO2 or GHG reduction potential, and economic benefit and includes appropriate case histories.Waste Heat SourcesSources of waste heat abound with the metals industry. While the overall quantity of energy is high, the sources are distributed throughout a plant. The largest source within the metals industry is within furnace exhaust / flue gases. This includes the high temperature gases from burners in process heating such melting, calcining, and sintering operations. It also includes lower temperature gases from heat treat, dryers, and heaters. Lower temperatures are also found after post processed hot gases. This could include heat left after heat exchangers, regenerative systems, thermal oxidizers, and emission control systems. Other hot gases include air used in direct and indirect cooling.While waste heat in form of exhaust gases is readily recognized, waste heat can also be found within liquids and solids. Waste heat within liquids includes things such as cooling water, heated wash water, and blow down water. Solids can be hot product at discharge after processing or reactions are complete. Indeed, not only is energy wasted in the hot metal that slowly air-cools, but additional energy may be used in providing air or water-cooling to increase the speed of cooling. Other waste heat sources are not as apparent and include things like hot surfaces, steam leaks, boiler blow down water, etc. Table 1 and Figure 1 show several major sources along with the temperature range and characteristics of the source."

Jan 1, 2011

By R. L. Miller

"Miners worldwide use a tremendous amount of energy in producing finished minerals for the end user market. In accomplishing this goal, they incur energy costs that can range from 20% to 30% of the total cost of production, so there is fertile ground for cost savings. To unlock this huge value in cost reduction, energy analysis is the key and is broken into several segments: 1. Fuel analysis for power generation 2. Energy supply & demand 3. Opportunity cost for lack of power 4. Backup power 5. Power contracts 6. Energy efficiency 7. Renewable energy 8. Continuous energy management FUEL ANALYSIS FOR POWER GENERATION What is the first thing we evaluate when looking at power supply alternatives for the mining industry’s large power requirements? Is it 1) site, 2) engineering, procurement, and construction companies, 3) independent power producers, 4) turbine vendors, 5) grid connections, or 6) fuel supply, logistics, and infrastructure? In evaluations of power supply alternatives for mining companies with special emphasis in developing countries, there is one over-riding conclusion: reliable fuel supply drives the energy generation economic engine. Evaluating several different fuels including liquefied natural gas (LNG), natural gas, diesel, heavy fuel oil, and liquefied petroleum gases (LPG) among others, the best project outcomes are those where fuel supply, pricing, logistics, and infrastructure are given an extensive amount of time during the analysis stage. In an assessment of the twenty-year costs of generating power from multiple fuels, each fuel’s costs were placed into three separate net present value (NPV) buckets of: 1) capital, 2) operating and maintenance, and 3) fuel. Within a range of 65% to 85% for all fuels, fuel cost was the largest component of the NPV of the life cycle power generation costs. So if 65% to 85% of your life cycle power generation cost is one item, shouldn’t miners spend a corresponding amount of time in the analysis stage fully understanding this key determinant for a successful power project? In developing countries where power generation infrastructure may not exist or does not exist at the same level as is found in North America and Europe, fuel analysis becomes even more important. One of the key questions for fuel importation in developing countries is the draft at existing ports to allow larger vessels to dock at the jetty. Can larger ocean-going tankers dock at the port for off-loading, or is the port’s draft too shallow, thus forcing a Single Point Mooring (SPM) system or Conventional Buoy Mooring (CBM) system to be constructed at substantial capital expense? Once fuel can be imported, sufficient onshore storage capacity should exist, or must be built to off-load the entire fuel cargo from the larger ships. Additionally, the throughput capacity of the pipeline from SPM/CBM must allow a rapid unloading of the fuel from ship to shore to eliminate steep demurrage costs for the project."

Jan 1, 2017

By Raymond B. Ladoo

Talc is a hydrous magnesium silicate having the chemical formula H2Mg3 (SiO8 ) 4 ; it is often called steatite, soapstone or potstorie, and by the trade names talc clay, agalite, asbestine, and verdolite. The term talc may be used to include all forms of the pure mineral, whereas steatite denotes particularly the massive, compact variety, and soapstone the impure, massive form that often contains only 50 per cent of talc. Merrill 1 says: The name soapstone is given to dark-gray and greenish talcose rocks, which are soft enough to be readily cut with a knife, and which have a pronounced soapy or greasy feeling; hence the name. Such rocks are commonly stated in textbooks to be compact forms .of steatite, or talc, but as the writer has elsewhere pointed out, and as shown by the analyses here given, few of them are even approximately pure forms of this mineral, but all contain varying proportions of chlorite, mica, and tremolite, together with perhaps unaltered residuals of pyroxene, granules of iron ore, iron pyrites, quartz, and, in seams and veins, calcite and magnesian carbonates. When pure, talc is soft, having a hardness of 1, but when impure or when it grades into its varieties, the hardness increases to 3 or 4. Talc ranges in color from pure white and silvery white through gray, green, apple green, gray green to dark green, nlso yellow, brown, or reddish when impure. It is rarely, if ever, found in wellformed crystals, but often occurs in foliated plates or in fibrous aggregates. It is commonly compact or massive or in fine granular aggregates. Several analyses of talc from different regions ·are given in Table 1. Talc has several varieties, the most important of which is Rensselaerite. This variety, found in a small area near Gouverneur, St. La.wrence County, N. Y., is a hard, fibrous, -waxlike mineral having the same chemical composition as talc, but lacking its softness and its peculiar greasy feel. Its hardness and its peculiar fibrous form, even when ground, have made its grinding and separation a separate problem. In addition to the varieties of talc and soapstone, the mineral pyrophyllite or agalmatolite, a hydrous silicate of alumina, with the formula H2Al2 (Si08 ), is also mined and sold as talc. It resembles talc in color, feel, luster, and structure, and may be successfully substituted for true talc for most uses. In this paper it will be considered as one of the commercial forms of talc.

Jan 1, 1923

U.S. demand for building and construction materials, such as construction aggregate, gypsum, and cement, remained strong in 1989. Cement imports declined slightly, representing about 17% of apparent consumption compared with 19% in 1988. Mexico, supplying 29% of the total, was the primary source of imports, followed by Canada with 21 %, Japan with 14%, and Spain and Greece with 10% each. Mexico was also the target of an antidumping petition, filed by producers in Arizona, Florida, New Mexico, and Texas, alleging that Mexican cement was being sold in these areas at less than fair value. This was the second petition filed against Mexico in the last 3 years. The International Trade Commission made a preliminary determination that the cement industry in these regions was materially injured by Mexican imports. U.S. demand improved for construction aggregate for the fourth consecutive year and was at a near-record level. The U.S. gypsum industry performed well, even though new housing starts decreased for the third consecutive year. Increased U.S. exports of gypsum wallboard and strength in the remodeling markets offset the impact of declining housing starts.

Jan 1, 1990

By William R. Barton

Dimension stones, with their almost infinite variety, have a broad range of properties and uses. Natural stone was beyond doubt the first mineral commodity used by man. Today dimension stone has widened to encompass building exteriors and interiors, decorative and ornamental modes, statuary, monuments, paving, curbing, flagging, roofing, and miscellaneous categories such as blackboards, surface plates, and honestones. For many purposes, it competes with greater or less success with alternate materials such as concrete, metal, brick, plastic, or glass. The almost ubiquitous geographic distribution of stone resources is the basis for a dimension stone producer industry in almost every State and in almost every land. In the United States, alone, dimension stone sold or used by quarries is valued at 2 million to 3 million dollars annually. Mining, finishing, transportation, and use technology have been modernized, resulting in a broader spectrum of stone products and new adaptions in use. Increased efficiencies also have been reflected in costs and prices and, coupled with gains that should be realized from current research, auger well for continued vitality of the ancient and honorable dimension stone craft.

Jan 1, 1968

By The Staff

Introduction For many years the necessity of mechanization of all the underground services in the collieries of the Dominion Steel and Coal Corporation in the Sydney, Pictou, and Cumberland coalfields has been foremost in the minds of those concerned with the engineering and operating policies of the Corporation, and a gradual policy of the mechanization of these services has been undertaken over the years, until nearly all the underground services, except the actual loading of the coal at the face, have been mechanized. Early in 1928, experiments in mechanical loading were conducted which finally culminated in the installation of mechanical loading units in our No. 20 colliery in 1938. This attempt at mechanization of the final underground services proved unsuccessful because the workmen were not ready to accept complete mechanization, and the fruition of many years of study was delayed until the year 1947. During the ensuing years, the engineers and operators of the Corporation had studied the possibility of adapting to conditions prevailing in Nova Scotia mines the many types of loading equipment in use in the United States and Europe. The varied physical conditions which exist in the fields operated by the Corporation rendered it extremely difficult to apply the equipment and technique successfully employed in the United States, and more recently in Europe, and special techniques have had to be devised to meet the need of each individual colliery. Prevailing physical conditions in the Nova Scotia fields find no parallel for mechanization with those of any other part of the American continent.

Jan 1, 1949

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By P. Gelfi, J. Vanderbeek, J. Enriquez

"The Cerro Verde copper-molybdenum mining complex is located near Arequipa, Peru. A 108,000 t/d copper concentrator (C1 concentrator) commenced operation in late 2006 and was debottlenecked to a 120,000 t/d capacity in 2011. A feasibility study, initiated in May 2010, assessed the potential for expanding the processing rate of the large Cerro Verde sulfide reserve via the installation of a second, stand-alone, concentrator (C2 concentrator) capable of processing a nominal 240,000 t/d ore. The feasibility study was successful and the project advanced through engineering, permitting and construction. Ramp up to nameplate capacity was ahead of schedule. The overall project was completed on schedule and within budget. The details of the project and supporting components are described. The design philosophy and design basis of the concentrator facilities are discussed as are factors that influenced the concentrator layout. Risk mitigation features included in the design are reviewed. The factors that drove the successful and rapid ramp up to nameplate capacity are discussed. Operational experiences in the first year of plant operation and project lessons learned are described. INTRODUCTION/BACKGROUND Sociedad Minera Cerro Verde S.A.A. (SMCV) operates a copper mine near Arequipa in southern Peru. Small scale operations operated intermittently until 1970 when the deposit reverted to the ownership of Minero Perú S.A (Peruvian government). Minero Perú S.A. commenced mining and processing of oxide reserves in 1972 and placed an SX-EW plant into production in 1976. The ownership of the property has changed hands several times over the years. Minero Perú sold Cerro Verde to Cyprus Climax Metals in 1994. Cyprus was acquired by Phelps Dodge in 1999. Freeport-McMoRan (FCX) acquired Phelps Dodge in 2007. Several studies were undertaken during the 1990’s that tried to establish the economic justification to process the large primary sulfide resource that underlies the surface oxide deposit. None of these studies produced an economic conclusion until a feasibility study was completed by Phelps Dodge and SMCV in 2004. This study provided the economic justification for the construction of a 108,000 t/d concentrator during 2005 and 2006. The key to the success of this study was identifying a water source that was sufficient to support processing economies of scale. Concentrator operations commenced in late 2006. The original design production rate of 108,000 t/d was achieved on a 30 day moving average basis on the 266th day after ore was first introduced. During 2009, studies and evaluations were performed that had the objective of addressing observed concentrator bottlenecks to allow a production rate of 120,000 t/d to be achieved. The 120,000 t/d figure represents the sustainable production limits associated with the installed primary crusher and tailing thickeners which would have been prohibitively expensive to upgrade. Debottlenecking activities were implemented during 2010 allowing sustained production rates of 120,000 t/d to be achieved."

Jan 1, 2017

By Leslie S. Weldon

THE Lake Shore mine has been developed by two vertical shafts, with level intervals at 200 feet to the 2200 level and at 125 feet below this horizon. A main cross-cut joins the two shafts on all levels to the bottom of No. 3 shaft, and opening into these cross-cuts are the ore passes and sand passes, which are completed from surface To the 4450 level. In the west part of the mine, additional connections have been made between No. 1 and No. 2 veins, through which the major part of the ore from No. 2 vein west is routed to drifts in No. 1 vein. With the lesser amount of stoping on No. 1 vein, this arrangement permits better haulage to be maintained. The ore passes are driven at 50 degrees from the ends of short cross-cuts off the main ones and are broken through to the levels above at the mouths of the short cross-cuts, to allow for dumping on each level. The passes are controlled at each level by ball-and-chain gates and deliver to crushers and thence to loading pockets, shown in Figure 1. That system is quite flexible in that it is possible to by-pass the crushers at any station and load from either shaft at a number of different pockets. The sand passes are driven from the main cross-cuts at the same inclination as, and parallel to, the ore passes. Each is equipped with a chute and dump hole, so that waste or sand fill may be loaded or dumped at each level. A transfer door, hinged on the bottom, is installed opposite the chute for by-passing fill from one level to the next, and in the closed position protects the opening at the top of the pass. The dump hole situated beside the transfer door is protected by a grizzly with 10-inch spaces. Waste rock may be withdrawn from the system through No. 3 shaft loading pocket at the 2950 level to a waste bin on surface. Levels are developed by drifts in No. 1 and No. 2 veins for their entire lengths. Subsidiary breaks are followed at a later date, when full information has been obtained by exploration, and a considerable amount of development by sub-drifts is carried out in the upper part of the mine, particularly in more or less erratic sections of No. 1 vein.

Jan 1, 1936

By A. H. Harvey, M. Delangen, A. D. Fernie

"A large-scale expansion to Pacific Coast Bulk Terminals Ltd. has now been completed and placed in operation. The original plant, built approximately eight years ago, consists of the direct rail-car to ship transfer of bulk commodities. The extension includes additional rail-car unloading, a transfer house system for directing commodities to storage or ship, major storage and reclaim facilities, a second shiploader and a second deep-sea berth. In addition to the facilities for overseas shipments, a wood-chip loader and a barge berth have been installed for domestic shipments of wood chips and, occasionally, for other local commodities. The design considerations imposed by the nature of the products to be handled are covered in this paper."

Jan 1, 1969

To improve communication among Government, industry, and academic researchers in the field of thermodynamics, the Federal Bureau of Mines sponsored a Workshop on Techniques for Measurement of Thermodynamic Properties in August 1979. Participants at the workshop presented 33 papers on the subjects of temperature measurement and control, general calorimetric techniques, low-temperature calorimetry, high-temperature calorimetry, galvanic cells, ionic solutions, and heterogeneous phase equilibria. A special invited lecture was presented by E. F. Westrum, Jr., on the resolution of lattice heat capacity. This Information Circular comprises the proceedings of the workshop and includes the texts of papers presented and discussion by attendees.

Jan 1, 1981

By W. L. Cooley

The report provides a detailed analysis of 23 electrical accident countermeasures contemplated for use in the metal/non-metal mining industry. The costs and potential benefits of implementing groups of these countermeasures are estimated, and methods arc outlined by which the operator ran choose countermeasures in an effective manner. The analysis is based largely on an extensive electrical accident event tree which is developed in detail. For those countermeasures which are not currently technically feasible, several prototype devices were developed to help speed development. These included a trolley arc eliminator and a safer mine electricians multimeter.

Jan 1, 1982

Jan 1, 1989