Search Documents

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

The Shortage of Mining and Metallurgical Engineers I N many parts of the Western World attention has recently been drawn to the acute shortage of mining and metallurgical engineers produced by the universities. Naturally, the reasons for this shortage have been discussed, and various remedies for it have been proposed. In this paper, I want to examine some of them. It is now fairly generally ac-cepted among mining men that the easy attractions of modern urban life have left the career of mining in the metaphorical as well as in the literal backwoods. The industry finds it increasingly difficult to recruit adventurous and intelligent young men; for such men now seek their intellectual, if not physical, adventure in more glamorous occupations from a safe social base in suburbia. The salaries, opportunities and security offered by the mining industry do not complete effectively with the rewards offered by other industries and by commerce, taking into account the social disadvantages of a mining life. The excitement and other non-material attractions of mining

Jan 1, 1965

By Jorge Misle, Daniel Silva

"This paper addresses the need for advanced control technologies and strategies in the mining industry, its potential and actual impact on mining processes and the best practices for their implementation, operation, and long term sustainability. It is well known that advanced process control (APC) can be a very good source for incremental process improvement for the mining industry, yielding to higher production rates or helping maintain consistent production rates despite ore changes. The application and integration of new technology, process knowledge and innovation are key elements in building such a supporting structure. More specifically, and this cannot be emphasized enough, the correct application and assembly of control tools, the in-time presentation of key data to decision makers and the development of relevant statistics and KPI’s (key performance indicators) can and will make a difference not only in terms of production, but also in plant stability, availability and production costs. In deploying such ideas and aiming at the long-term goal of "Operational Excellence", Minera Los Pelambres (MLP) has developed a number of successful control strategies, best practices and technologies, which are not only the application of state-of-the-art automation and computing tools, but rather the assembly of the above presented structuring factors. This work discusses some of the key tools and ideas implemented for SAG & Ball milling and Flotation areas, their performance results and the roadmap taken for the integration of process knowledge and control tools. Also, cases studies are presented and discussed further to not only show the main areas of improvement, but also to highlight the benefits of such strategy that for the most part, deviate from the traditional mining industry control approach. Also, a word is given on the need for innovating in the design of control strategies and leveraging best practices and process knowledge that ultimately, will contribute to long-term reliable operations, improved mineral processing and, although unmeasured, lead to a superior overall performance and productivity of all mining personnel involved."

Jan 1, 2014

By GEORGE S. POPE

The Government of the United States annually expends approximately $8,000,000 for coal. Prior to 1906, this coal was purchased mainly on its reputation, or trade name, rather than under contracts specifying the heating value of the coal, its contents of ash and moisture, and other characteristics. In recent years the Government and other large consumers have appreciated more and more the desirability of definitely determining by chemical analyses and tests the character and quality of coal deliveries. Studies of engineroom and boiler-room efficiencies and economies point forcibly to the necessity of devoting more thought to the improvement of the boiler-room end. This calls for an intimate knowledge of the character and quality of the fuel used. The analyses and tests of delivered coal furnish such data, whereby the power-plant results can be comprehensively studied and a continuous check maintained on the coal and on the conditions of plant operation. Under authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, 'Washington, D. C., where samples representing deliveries of coal purchased for Government use are analyzed and tested. The Bureau of Mines has been active in promoting the purchase of coal by the Government under specifications,a that is, by contracts that make definite requirements regarding the heating value of the coal expressed in British thermal units, and the composition as shown by proximate analysis. Under many of these specification contracts the bidders guarantee the quality of the coal offered, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled and analyzed to determine whether the coal is of the quality guaranteed by the contractor, and if it is not, the price to be paid is decreased in proportion; but if the coal is of higher quality, the price is proportionately increased. The analyses of coals or the guaranties offered by the bidders may in some cases be used for determining the award of a contract, but if the coals offered are of widely different characteristics, it may be difficult to determine which would prove the cheapest fuel, without having their relative evaporative efficiencies. Hence, it may be necessary to conduct evaporative tests under service conditions in order to determine which coal is particularly adapted for successful and economical use in the plant. But once a particular coal is selected, regardless of the procedure of determining the award of a contract, then the greatest advantage of the specification method is realized, in that it guarantees to the purchaser coal of uniform character and quality, thereby insuring the best results in the plant. The cost of purchases, under such specifications, of fueL for the use of the Government now aggregates approximately $4,100,000 per annum, and the cost of additional fuel for which samples are taken and submitted to the Bureau of Mines for analysis in order to determine the character and quality of the coal furnished aggregates some $3,000,000 per annum more. In fact, information is now obtained regarding the quality of fuel purchased on almost all contracts large enough to warrant sampling and analysis and heatingvalue tests. It may be said that the purchase of coal under specification is still in the stage of evolution and development, and that experience and time will be required to develop fully standard specifications and methods of sampling and analysis that may be used universally. The success of the specification method for the purchase of coal and the reliability of analysis now rests almost entirely on sampling.a Improper sampling leads to controversies, with resulting condemnation of the specification method in general and the value of laboratory analyses and tests in particular. A number of bulletins b have been published showing the results of the purchase of coal by the Government under specifications. This bulletin is a compilation of the results of coal analyses by the Government, including those made in the fiscal years 1908-1910, which have been previously published, and later analyses representing coals analyzed during the fiscal years 1911-1915. The preceding bulletins gave individual analyses or average monthly analyses, whereas this bulletin gives the average analyses only for the entire contract. It is hoped that this compilation of a series of comparable analyses of the coals purchased by the Government will be of value alike to coal dealers, to Government engineers, to purchasing agents, and to all users of coal.

Jan 1, 1916

By H. S. Auvil, J. T. McCartney, J. D. Davis

"INTRODUCTION It is now generally recognized that the small-scale laboratory dilatometer method of test does not give results of much utility in predicting the expansion (or contraction) of a coal in a coke oven. The carbonizing conditions in the laboratory test differ radically from those in the oven; in this test, the charge is heated through the coking range of temperature as a whole, whereas in the oven, coking proceeds by layers parallel to the oven walls as each succeeding portion of the charge goes through the plastic range of temperature and coke formation sets in. The paths of the gases and vapors and the pressures set up are different in the two methods. Furthermore, the rate of heating in the test usually is much more rapid than in the oven. H. Koppers 5/ was perhaps the first to adopt apparatus and procedure whereby the layer coking of the coke oven could be simulated closely however, the heating progressed from one side of the charge only; later he experimented with a small coke oven with a movable wall heated from both sides. It is not clear how well the results in the later oven correlated with those of the earlier small test oven, but in a comparatively recent Koppers publication a modification of the original small test oven heated from one side is recommended 6/ Altieri 7/ was perhaps the first to experiment with the Koppers type small test oven in the United States and Brown- has tested a large variety of coals in a rectangular test oven of his own design heated from the sole or floor. Subcommittee XV of American Society for Testing Materials Committee D-5 is now making a study of the various methods proposed for determination of expanding and plastic properties of coal with a view to standardization. 9/"

May 1, 1939

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011

By Egil Aukrust

"An American Iron and Steel Institute Task Force evaluated developing direct steelmaking technology worldwide to seek a replacement for the coke-oven, blast-furnace, basic-oxygen process technology now in use. To remain internationally competitive it is essential to move away from the traditional series of batch processes towards continuous processing and the associated energy savings which are possible with high technology process control systems. The group identified in-bath smelting of iron ore pellets or fines with coal as the process most sui table for domestic raw materials (including abundant scrap) and called for research to study operation with varying degrees of preheat and prereduction of the ore by the gases generated from the coal and various degrees of combustion of these gases above the melt.A coordinated, 3-year, $27 million, direct steelmaking research program is proposed. Concurrent projects include design, construction, and experimental operation of an in-bath smelting pilot plant; modeling, simulations, and laboratory-scale experiments at universities on slag-phase and metallicphase reactions and interactions; and large-scale heat transfer and reaction rate trials. Also included are modeling studies and pilot plant trials of on-stream decarbonization and desulfurization; application of circulating fluid bed technology to fine ore reduction and hot gas cleanup; and specific heat transfer and fluid flow research projects.IntroductionThe American Iron and Steel Institute (AISI), based on the Task Force studying direct steelmaking, believes strongly that a coordinated program of research on the reduction of domestic raw materials to liquid steel should be undertaken as part of the Steel Initiative program. To specify the steelmaking process for development best suited to the American steel industry and domestic raw materials, it was important to determine the state-of-the-art of direct steelmaking worldwide, both as practiced and under development, and then, by expert analysis of the processes and their potentials, to choose the process most likely to provide a domestic competitive edge."

Jan 1, 1988

By A. J. Sinclair, N. Champigny

"The Cinola gold deposit in the northern Queen Charlotte Islands, British Columbia, is in a clastic sequence consisting of a lower shale of the Late Cretaceous Haida Formation and an overlying interbedded sequence of pebble conglomerate and coarse-grained sandstone of the Middle Miocene Skonun Formation. Both formations are intruded by a stock and dykes of porphyritic rhyolite. Two K-Ar model ages indicate mineralization and probably porphyritic-rhyolite intrusion at about 14 Ma (middle Miocene). A splay of the Sandspit fault system constitutes the footwall on the west of the deposit.The Cinola deposit can be classed as Carlin-type based on features such as (1) small particle size for gold, (2) Tertiary age of mineralization, (3) element abundances (e.g. high Hg), (4) dominantly argillic alteration, (5) a structural setting associated with major faults, (6) porosity of the host rock and (7) spatial and possibly genetic association with felsic intrusions. Gold is widespread and occurs mainly as grains of< 0.5 11-m in silicified sedimentary rock, and in quartz veins. Locally, coarse > 100 11-m particles of native gold occur in quartz veins, especially in strongly brecciated porphyritic-rhyolite. Ore minerals are mainly pyrite and marcasite, but include small amounts of chalcopyrite, sphalerite, galena, pyrrhotite, cinnabar, tiemannite (HgSe), rutile, magnetite, hematite and limonite in addition to native gold and electrum. No silver minerals have been found; silver was found in gold particles in amounts varying from 6.2 to 24.2 weight per cent. Alteration products are sericite, illite, kaolinite and chlorite, with abundant quartz of several stages.The host rocks, specifically the Skonun Formation, formed as an alluvial plain facies in a braided river system discharging into a marine basin in early Middle Miocene time. During the Middle Miocene, this sequence was intruded by a rhyolitic stock. The highly porous and permeable Miocene clastic sequence apparently provided an optimum setting for the development of a large geothermal system, the energy for which probably derived from the rhyolite stock. Mineral deposition followed a well-defined paragenesis, which, from oldest to youngest, is: (1) precipitation of iron sulphide minerals, and early quartz; (2) several stqges of quartz veins, with deposition of sphalerite succeeded by galena, chalcopyrite and visible gold. Micron-size gold was precipitated throughout these two stages of mineral deposition. Argillitization of the host rocks probably in part coincided with the mineralization and continued during cooling of the geothermal cell.In-situ reserves have been estimated at 41.1 million metric tons averaging 1.85 g Au/tonne using a cutoff grade of0.86 g Au/ tonne."

Jan 1, 1982

By C. E. Julihn

In the past few years the advance of the Sunshine mine to national prominence as the chief silver-producing mine of the United States has revived interest in the area in which it is situated. Although this area lies between the great lead-Zinc-silver mines at Kellogg and those in the vicinity of Burke and Mullan it was generally presumed to be almost barren, as little ore had been found there until substantial ore bodies were developed on deep levels of the Sunshine mine. In early days it was called the "dry belt" because its ores were siliceous and contained little lead; but the classification of ores in smelting as wet or dry, although once customary, has long been obsolete The area will therefore be referred to in this paper as the silver belt of the Coeur d&apos;Alene district because the value of its ore is due chiefly to silver, the current production of which is large, providing over 60 percent of the silver output of Idaho. Silver Belt - Its Limits and Character With a daily production of half a ten of silver or more from the Sunshine mine, the silver belt has become the scene of extensive exploration at many properties, and the outlook for its future seems promising enough to warrant the lively interest now being displayed in the area by the public.

Jan 1, 1936

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau&apos;s measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau&apos;s investigations. Typical comparative data are included.

Jan 1, 1986

By J. G. Nalven

On July 1, 1999, most domestic metal mines will have to report releases of toxic chemicals into the environment for the first time as required by SARA Title 313. Some of these reportable releases will appear huge in relation to reports by other industries. The reasons for the potentially large reportable releases, special considerations for mining operations, and strategies for dealing with the reports are described. Data composited from experience with several mining companies is presented in the context of a typical gold mine.

Jan 1, 1999

By Andrew Thomson, Peter Wright

"A section of a London Underground expanded segmental lined tunnel constructed in the 1970’s progressively deteriorated after 2001, with extensive radial joint spalling and mid-segment cracking. As part of the PPP contract Tube Lines Ltd and their partners carried out various analyses of the tunnel, including analysis of laser scans of the tunnel, geotechnical testing through the tunnel walls, geotechnical desk studies, real-time monitoring and even full-scale segment testing. This paper discusses the behaviour of the tunnel lining in this setting, the causes of failure and the lessons that can be learnt from this rare example of a tunnel which was progressively failing in service. It is finally noted that a replacement tunnel lining was installed during night-time possessions and completed in 2015. INTRODUCTION In 2003, Tube Lines Ltd. was established under a Public-Private Partnership (PPP) scheme to provide maintenance services and upgrade projects for London Underground (LU). The Deep Tube Tunnel Knowledge and Inspection Programme comprised the assessment of all tunnels, shafts and other underground structures. This included a number of lengths of tunnel constructed using segmental concrete linings. First used by LU in the 1960s, the savings both in cost and speed of construction led to concrete linings replacing cast iron for new tunnel construction in all but a few cases. During the initial scoping phase of this programme, inspections identified potential issues with the expanded concrete segmental linings on the Jubilee line. The inspections found a number of segments with surface spalling (Figure 1a), which did not appear on the post-construction defect records. These were generally relatively shallow, up to 40mm deep, spread over a wide area of segment. These were different to spalls caused by handling damage, which are typically localised at segment corners. Subsequent inspections over the following years identified an increasing number of segments with these types of spalls as well as an increased incidence of longitudinal mid-segment cracking (Figure 1b). The increasing occurrence of these defects was hypothesised to be caused by tensile stresses developing in the vicinity of the joint."

Jan 1, 2016

By G. Boehler

The purpose of this program is to demonstrate the feasibility and practicality of noise control for secondary and tertiary crushers in surface non-coal mining plants and mills. It is a part of the broad Bureau of Mines program to reduce noise in mines to levels mandated in the Coal Mine Health and Safety Act. Utilizing the results of previous contractual research efforts in which noise levels of secondary crushers had been measured, two noise enclosures were designed and evaluated for the REXNORD Symons 7-ft diameter secondary and tertiary crushers installed at the Jackson County Iron Company, in Black River Falls, Wisconsin. The first enclosure had a circular shape following closely that of the crusher and was built up entirely of quick-release panels which can be handled by the crusher operator alone. The second enclosure was octogonal in shape and can be rapidly removed, partially or totally using an overhead crane. Both enclosures fully satisfy the noise reduction objectives and permit daily and long-term maintenance of the crushers. Cost analyses show the cost of the enclosure to be less than 10 per cent of the cost of the crusher, the cost of the octagonal enclosure being estimated at only 60 percent of that of the circular one, e. g. $15,000 against $25,000. It is concluded that the octagonal enclosure best meets the needs of the Jackson County Mining Company and it is recommended that an experimental enclosure be built at the earliest possible time, as proof-of-concept.

Jan 1, 1977

By K. Hardy

As part of Inco&apos;s $115 million Fluid Bed Roaster SO2 Abatement Project, a new weak acid treatment plant (WATP) was constructed to treat bleed solutions from the Copper Cliff Smelting Complex gas-cleaning circuits. The WATP produces an iron-arsenic co-precipitate, termed "basic ferric arsenate" (BFA), which requires disposal in an environmentally acceptable manner. Following analysis of many potential options, the short-listed disposal alternatives were: A) Co-disposal of the BFA?gypsum sludge with rock tailings, a portion of which would be used in mine backfill, with the remainder being sent to the tailings area, and B) Co-disposal of BFA?gypsum sludge with pyrrhotite tailings in the tailings area. Testwork showed that the addition of BFA?gypsum sludge to mine backfill samples increased the uniaxial compressive strength (UCS) of the backfill for most samples, especially those at lower binder content ratios. Extensive analysis was conducted on samples taken from the Copper Cliff tailings area, where BFA?gypsum sludge from Inco&apos;s Copper Refining Electrowinning Department has been co-deposited with pyrrhotite tailings since 1990. Pore water samples from these areas contained very low arsenic concentrations, indicating that the arsenic had remained stable in that environment. Ultimately, co-deposition with pyrrhotite tailings was chosen as the preferred option for the disposal of BFA?gypsum sludge from Inco&apos;s new WATP.

Jan 1, 2006

By J B. Pateiro-Fernßndez, M Fuchsschwanz, G Deissmann, S Ahmad

Quang Ninh province is the most significant coal producing region in the north of Vietnam. The Nui Beo Coal Company (NBCC) operates open pit mines in Quang Ninh province and the waste overburden produced is dumped as sidehill fill in the Chinh Bac waste dump site. In the past, no special consideration has been given to the environmental impacts during the dumping operations. The mine waste is transported in trucks from the mine site to the dumping site and the loading, hauling and dumping operations are the main sources of dust emission. Rain events, especially during the rainy season, cause the generation of contaminated surface water as well as seepage of water through the dump at a number of locations. The existence of cracks at the top of the dump can pose serious stability problems with heavy rain events leading to failure of slopes which can potentially disturb vast areas of land currently used for agricultural purposes and human settlement. For sustainable development at the Chinh Bac waste dump site in the future, apart from the social and economic considerations to be assessed, there is an absolute necessity for environmental protection measures to be in place both during and after the dumping of the mine waste overburden. Research Association Mining and Environment in Vietnam (RAME) is working to develop and implement concepts for the mitigation of environmental problems emerging from dust, contaminated water and lacking slope stability to ensure successful rehabilitation of the coal mine waste dumps in the north of Vietnam. Within the framework of RAME, the Institute of Mining Engineering I (RWTH Aachen University) is managing and working to develop the stabilisation concepts for the solid mine waste dump in collaboration with the Chair of Geotechnical Engineering (RWTH Aachen University), Brenk Systemplanung and the Vietnamese group of companies VINACOMIN (Vietnam National Coal-Mineral Industries Group). The most economical and environmentally sound operations, as well as locally adaptable environmental protection measures, are essential for the sustainable development of the dumping operations at Chinh Bac dump. This paper describes the dump site and the sustainable development possibilities with an emphasis on the environmental protection and stability problems at the Chinh Bac waste dump.

Jan 1, 2009

By V Chamberlain, M Appeah Owusu, M Aniawu-Asumakah, A Anyimadu, R Peattie

This is an integrated geology and plant improvement study arising from the heterogeneity seen in mineralogy and gold association at the Obuasi goldmine in Ghana. This heterogeneity comes from the two ore types mined, the one being a sulphide ore, mainly composed of gold-bearing arsenopyrites. This gold is refractory and exhibits a strong relationship between gold and As. The other is quartz veins, that are high grade and free milling. The installed circuit consists of comminution – Gravity -Flotation – BIOX – Leaching and Adsorption processes. The opportunity tested involved improved mass pull - related flotation recovery of Au in the Sulphide stream; while balancing the need for a minimum Sulphide grade for the Bio-oxidation process, occasioned by the removal of 25 to 30 % of the (quartz) stream through preconcentration by Ore sorting. The current circuit is then utilized for the sulphide route, while a smaller grind-gravity circuit is utilised for the quartz stream in a relatively inexpensive way, followed by a common leaching and adsorption circuit. Added advantages of the strategy includes faster recovery of gold from the quartz stream, with less consumption of reagents from saving on flotation and BIOX reagents for this stream. Screening and Ore sorting was successfully tested with laser technology, achieving over 98% separation of quarts (containing up to 40% of the gold). The plant schedule of Ore, the suggested circuit design for the Ore sorting, the results obtained from the different flotation regimes, as well as consequent financial modelling have been presented and discussed in this paper. This illustrates the opportunity that arises out of a detailed analysis of material versus installed circuits, even if the gains in pre-concentration do not necessarily involve rejection of gangue material. An added opportunity for future investigation, briefly discussed but not tested in this paper, would be to maintain current mass pulls but with increase in throughput (by the space created by the sorted material). This will of course require the mining ability. It could also add LOM value by altering the cut-off grade.

Nov 10, 2020

By G. Van Weert

Refractory gold ores and auriferous concentrates containing silver tend to form refractory silver jarosites during pressure oxidation. Earlier work with pure Ag2S has shown that the addition of iodine species to the autoclave feed yields cyanide soluble iodargyrite (Agl) instead. Near complete silver extractions from the autoclave product were obtained at a I-/Ag+ ratio of 5 or more. This paper reports on the pressure oxidation and cyanide leaching of two industrial refractory (arseno) pyritic silver-bearing concentrates: 1. from Peru (sulphosalts) and 2. from the USA (pyrite, with acanthite occlusions). While using a I-/Ag+ mol ratio of only 1 in the feed, it has been possible to obtain 98 and 97% Ag extraction from the two autoclave products by cyanide leaching, respectively. This compares to 11 and 54% Ag extraction from the as-received concentrates and 4 and 15% Ag extraction, respectively, after pressure oxidation without KI present. The results of the testwork are discussed in terms of concentrate mineralogy and pressure oxidation conditions.

Jan 1, 1994

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019