Search Documents

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By L. E. Collins

"In western Canada, many new wells contain a significant fraction of H2S. As well, many older wells become increasingly sour over their operating lifetime. For these reasons, there has been increased demand for linepipe and casing for sour service applications in recent years. This paper will review the metallurgical factors which must be considered in designing steels for such applications. IPSCO’s development of linepipe and casing, and experience in fabricating products to meet test standards specified for sour service applications will be summarized. IntroductionWestern Canada produces the majority of Canada’s domestic crude oil and natural gas. A complex system of pipelines has been built to gather the oil and gas from the fields for transport to refining and/or cleaning operations. The gas carried in these pipelines can be either sweet or sour (i.e. containing no H2S or containing H2S) depending on the nature of the field from which it came. Many new fields contain a significant fraction of H2S and many older fields become more sour as their time in production increases. This uncertainty regarding product condition influences the user’s choice of materials for both casing and pipeline applications.It is well known (Merrick, 1989) that hydrogen induced cracking (HIC) will occur in steel when three conditions exist simultaneously: (1) the presence of H2S gas, (2) moisture, and (3) a susceptible material. Steelmakers can only address the latter of these factors. Development of steels to meet test requirements of sour service has been a major focus of IPSCO’s development work for several years."

Jan 1, 1998

By J-P Strydom, J P. Z, S. Schafrik, M. Beck, Z. Agioutantis

Developing a method to accurately determine the weight and distribution of the load within a shuttle car bed eliminates the need for manual activation of the flight chain. Accordingly, this experimental study characterized the thermo-mechanical response of two unique load cells in force shunt, implemented as an engineering control to quantify load position and distribution without human intervention. The influence of environmental and installation conditions on the measurement accuracy was quantified and determined to be indirectly dependent on the characteristics of the material load cells that are mounted to.

Feb 22, 2026

By Manuel Gomez

This report presents low-temperature tar data from studies by the Bureau of Mines of tars produced in an externally heated (entrained state) pilot-plant-scale retort. Analytical data covering 20 low-temperature tars, derived from the. carbonization of various ranks of foreign and domestic coals, are tabulated. The character of the tar is discussed in relationship to carbonizing conditions and the rank of coal. It is seen that in carbonization techniques that employ entrainment or fluidization of the coal particle, carbonization conditions are secondary to coal rank with respect to tar-oil yields and composition. The influence of distillation conditions on recoverable yields of tar products is presented. The probable yield of commercially important chemical products, based on a ton of pure (moisture- and ash-free) coal, are predicted. INTRODUCTION Low-temperature tars produced by entrainment or fluidized carbonization techniques that employ internally heated reactors represent the most nearly primary tart produced by industrial processes. In brief, such a process involves the application of a heat gradient to the coal particle "boiling" or suspended in a turbulent state in the reactor chamber. Conditions are observed so that the coal particle remains suspended within the reaction zone by a gas stream for a time interval commensurate with maximum tar-oil yield. The heat necessary for the carbonization reaction may be obtained entirely from the hot (preheated) gas stream, or it may be derived partly from the combustion of the volatile products and char by the transport gases, usually air. The volatile material moves out of the carbonizing zone at a rate that approaches the velocity of the transport gas. Carbonizing conditions are ideal when a minimum particle residence time is obtained within the reactor at a given temperature and a maximum yield of condensable volatile matter is released. In industrial practice this objective is a compromise.

Jan 1, 1957

By John S. Alexander

By G. E. Willey

F OR many years, only one grade of structural steel has been used in volume in Canada. Its characteristics have not been altered appreciably and its long use speaks well for its performance. This standard grade of structural steel may be bought and specified as C.S.A. G40.4 steel or the American equivalent, A.S.T.M. A7. The principal limitations and requirements of this specification are shown in Table I. Within the last five years there has been a growing awareness among the steel producers and steel fabricators that economic forces are at work which make desirable the availability of new and better grades of structural steel. Competition from other materials has increased. The use of concrete bridges and pre-stressed concrete beams is a prime example. New sources of steel from outside the country have become a threat to the Canadian industry and its high cost-price structure. The need for improved properties in the steel, to make possible technologic

Jan 1, 1962

By L. R. Plitt

A series of experiments were carried out in an effort to develop a universally applicable mathematical model of the hydrocyclone classifier. The design and operating variables studied were: cyclone diameter and height, the inlet, vortex finder and apex diameters, the feed pressure and the solids content of the feed slurry. The model consists of four basic equations which express the cut size ( dso), volumetric split between overflow and underflow, volumetric throughput, and sharpness of separation in terms of the operating and design variables. Although empirical, the model is nevertheless in general agreement with fundamentally derived models. The model clearly 1•eveals the effect of the major variables on the operation of a hydrocyclone. Because of its broad data base and the inclusion of all the major variables, the model may be used without experimental data to predict the operation of cyclones over a wide range of different operating conditions. With operating data, the equations may be modified to serve as an operational model.

Jan 1, 1976

By V. Svalbonas

With the occurrences of serious mill structural failures on both ball and primary mills, the mining industry has entered the era of detailed fabrication specifications. Such specifications, however, have been developed as individual entities, often by people not related to the mill design function. Therefore, there has been no effort to relate mill failure or safety to the existence or elimination of specific fabrication flaws; that is, no cause-effect failure relationships have been developed. The omission of this step produces a specification which can be termed uneconomical at best. The present paper attempts to fill this void, by reviewing methods for design consideration of flawed structures, and describing experimental tests used to tie such data to a meaningful quality assurance program in fabrication.

Jan 1, 1985

By Ray W. Ballmer

Historically, Bingham is a rail pit, starting with steam locomotives in 1906 and converting to electric locomotives in 1923. Ore production was maintained through an effective utilization of available rail equipment. From time to time as it became necessary to deepen the pit and as stripping ratios increased, various studies were made on alternate material haulage systems. Utilization of diesel locomotives, conveyor belts, and trucks have all been subjects of study, however, conversion from rail haulage utilizing electric locomotives could not be justified. Because of the gradual decline in ore grade, a program was approved in 1963 to raise ore production to 108,000 tons per day. This was designed to return copper production to the 1950 level. Attainment of this production level by expansion of the rail system had definite limitations and built-in inflexibility. Track and trolley wire relocation causes shovel down time in excess of that required for normal maintenance. Instability of the dumps and the resulting additional track maintenance increases greatly as the volume of waste material to be handled daily expands.

Jan 1, 1965

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992

By Michael J. Beus

This Bureau of Mines report describes a field experiment involving the sinking of two test shafts to directly compare the deformational behavior of circular and rectangular shapes. Results show that the circular shape is less sensitive to geologic discontinuities and applied stress field. Also, the rectangular shape is subject to a variety of behavioral modes, including beam bending and buckling. Geologic discontinuities around circular and rectangular shapes influence displacement significantly. Simple, two-dimensional elastic finite-element modeling, simulating circular and rectangular shapes in a biaxial stress field, shows that the structural response of a shaft is largely controlled by geologic structure. Consideration of anisotropy may be required for realistic analysis of a deep shaft.

Jan 1, 1985

By Scott G. Giltner, Alex Schwenk

Blasting within 250 ft of a crusher was successfully executed through the application of electronic detonators, 3-D imagery, signature hole analysis, custom loading of blast holes. The blast was well contained, the vibrations were minimal, and there was no flyrock.

Feb 1, 2020

By Gary P. Sames

Shale roof deterioration in coal mines. caused by ventilation air humidity fluctuations, is a common ground control problem. Shale roof deterioration often results in increased accidents, decreased production, inadequate ventilation, and increasing operating costs in maintaining haulage roads and airways. The results of Bureau of Mines research indicate that air tempering entries are an effective method of controlling deterioration prone shales. Some of the conclusions and recommendations drawn from Bureau research include (1) moisture sensitive shales will react adversely to moisture gains and losses, (2) the majority effect of specific humidity fluctuations can be concentrated in and absorbed by tempering entries, (3) tempering entry panels should be located as near to the main intake as possible, (4) tempering panels should be designed for a conservative recovery and provide a minimum of 20-to 30-min air residence time, (5) ventilation and escapeway requirements must be considered early in panel design, and (6) an efficient support and sealant plan can increase the life expectancy of a tempering panel.

Jan 1, 1985

By D R. Anstey

The growing demand for iron ore from Western Australia has led to an increased focus on the development of magnetite and lower grade iron ore deposits. The need to process and beneficiate the ore from these projects can result in the generation of significant quantities of iron ore tailings over the life of a project. Over the coming decades, the management of iron ore tailings will become a significant aspect of the mining landscape in Western Australia.The tailings generated from iron ore projects differ signifi cantly from other mineral tailings currently produced in Western Australia. Iron ore tailings are generated on a scale not matched by any other mineral process and can often contain asbestiform or potentially acid forming components. New iron ore projects are coming under increased environmental scrutiny because of their large scale operations and the sensitive environments in which they occur. This combination of factors creates some unique challenges for the management of tailings generated by iron ore mining in Western Australia.This paper presents the fi ndings of two studies conducted in recent years to overcome the challenges posed by iron ore tailings. The paper discusses the role of laboratory testing in the development of management strategies for asbestiform minerals in tailings. It also presents a numerical modelling approach for evaluating the rates of rise in the storage of magnetite tailings. The paper concludes by outlining how the findings of these studies can be applied to reduce tailings management costs, lower risks and improve environmental outcomes for the management of tailings from iron ore mining.

Jul 11, 2011

By G. T. Krempasky

This report covers the installation and evaluation of lb reinforced concrete sets, 6 in each of 3 mines in the Goeur d'Alene mining district, Shoshone County, Idaho, and is the second of a series to determine the feasibility of a more permanent type of mine support. Closure measurements, where applicable, were made periodically of the concrete-set installations and were compared to the initial cross section of the sets. A different method of blocking was used at each test site; at one test site the type of blocking was changed several times during the test. Results from each test site are reported separately. No attempt was made to compare the cost of the concrete installations with the cost of other types of support used in the district. Such an evaluation of permanent types of support would require a longer period of time. At this time, tests are not complete enough to determine the applicability of underground concrete supports. However, results to date tend to confirm the general opinion that precast concrete mine supports could be used to advantage in openings that require support and must have long life, especially where decay of timber is an important factor.

Jan 1, 1963

By Clifford J. Lewis

The control of sulfur dioxide and fly ash in the emissions from coal-fired boilers is a significant segment of the national environ- mental protection program. Developing technologies to accomplish this objective presently emphasize aqueous scrubbing techniques. Should circumstances require aqueous scrubbing for fly ash control only, provision must nevertheless be made to counteract the presence of sulfur dioxide which can create an acidic and potentially corrosive environment. Major technologies for sulfur dioxide control by aqueous scrubbing include, l), recovery processes yielding sulfuric acid or elemental sulfur and 2), throw-away processes which produce a sludge consisting essentially of calcium sulfite or varying amounts of calcium sulfate.1/ Recovery processes are more sophisticated and best suited for locations where there are markets for sulfuric acid or sulfur, or where sludge disposal is an overriding consideration. Throw-away processes are generally less sophisticated but have a problem in that gas scrubbing systems may not operate for practical time periods without failures due to corrosion and to plugging by particulates and precipitates. To overcome this difficulty, some throw-away systems employ an aqueous solution of caustic in the gas scrubbing device to assure maximum water solubility of sulfur compounds, followed by the addition of lime to the scrubbing medium in a system external to the scrubber to produce the throw-away sludge and regenerate the caustic for recycle. Such systems are referred to as double alkali systems.2/

Jan 1, 1975

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By Glenn A. Hazen

This report presents a stress investigation of four coal pillars located under two depths of cover. Each coal pillar was instrumented with ten load cells designed to measure coal pressure during initial and secondary mining. The problem considered was one of uniform triaxial stress as a large coal pillar was loaded under a thick limestone bed. Special attention was given to pillar design procedure. Unconfined uniaxial compression tests were conducted for coal specimens 7/8 in., 2-1/8 in., 3 in., and 4 in. square with length to square side ratios of 1/2, 1, 1-1/2, and 2. Stress-strain curves were recorded. Six specimens were tested at each size. Results show that a coal pillar is composed of an inner zone which is highly loaded plus a region around its perimeter which has lost its elastic strength. The bearing capacity of a coal pillar consists of elastic and crushed coal response: The failure strengths have been determined and will be useful in coal recovery, mine design, and mine safety.

Jan 1, 1975

By E. V. Verhoef

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-lndicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LeA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LeA assessments, thus leading to erroneous results. The suggested approach provides directions for including these external effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By E. V. Verhoej

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-Indicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LCA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LCA assessments, thus leading to erroneous results. The suggested approach provides directions for including these extemal effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003