Search Documents

By F. D. Osgood, A. C. Fieldner, W. A. Selvig

In connection with investigations being conducted by the Bureau of Mines regarding pulmonary disease which is prevalent among metal miners in certain districts , a large number of rock- dust samples have been collected , and have been examined in the Bureau's laboratories . The earlier work has been described in Bureau of Mines Technical Paper 105 , " Pulmonary disease among miners in the Joplin district , Missouri , and its relation to rock dust in mines " by A. J. Lanza and Edwin Higgins , 1915 , and in Bureau of Mines Bulletin 132 , " Siliceous dust in relation to pulmonary disease among miners in the Joplin district , Missouri , " by Edwin Higgins , A.J. Lanza , F.B.Laney , and Geo . S. Rice , 1919. The methods of collecting and examining dust samples have been greatly improved during the investigation , much valuable information having been made available by similar investigations conducted by the Miners ! Phthisis Prevention Committee , Union of South Africa . The latter are described in the " General report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1916 " , and " Final report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1919. " The investigations by the Bureau of Mines and the South African committee show that by prolonged inhalation of air containing minute particles of sharp and insoluble rock dust , the lungs retain sufficient dust particles to cause decided injury to the lung tissue , the injured lung becoming very susceptible to the development of tuberculosis .

May 1, 1920

By C Reed

Titaniferous magnetite deposits are a significant source of vanadium for use in high strength steel alloying and other chemical applications. The mineralogy of the deposits varies markedly and the ore characteristics strongly influence the process route selected and the metallurgical outcomes. Characterisation of the ores reveals the presence of magnetite, ilmenite and other minerals such as spinel hematite and goethite with variable degrees of weathering along with weathered products of host rock. The standard processing route is to crush, grind and magnetically recover a concentrate for salt roasting to produce a soluble vanadate. Ore beneficiation is practised to generate an iron based mineral concentrate containing much of the vanadium with low silica levels of two per cent. Typical processing problems encountered are fine liberation size, over grinding of the magnetite and variable response to magnetic separation resulting from the weathering profile. Beneficiation options are restricted, and generally focused on producing a combined iron and titanium rich concentrate containing vanadium due to the fact that ilmenite and magnetite and their products of weathering are magnetic and have similar specific gravities making their separation difficult. The ilmenite usually contains low levels of vanadium making its separation highly desirable from the iron mineralisation containing higher levels of vanadium. Salt roasting of vanadium ores followed by water leaching has been the standard processing route for many years. The cost of suitable sodium salts, availability of capital and increasing energy costs and energy availability are critical factors in determining the viability of aspiring vanadium producers. To date, only Windimurra has acquired full capital funding, secured energy and sodium salt supplies at suitable cost that enable the construction of the project. Low overall recoveries of vanadium to concentrate roasting at up to 1200¦C are critical cost issues. In this paper, factors influencing the recovery of vanadium are reviewed and emerging processing trends explored. The important features of the processing of titaniferous magnetites have been condensed from the literature, published works, company websites, our own work and personal communication.

Jan 1, 2008

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0.5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that quenched slags can be treated at slightly lower cost than slow-cooled slags. However, the cost advantage of processing quenched slags is more than offset by the higher copper recoveries obtained from slow-cooled slags.

Jan 1, 1971

By K Afewu, R Dunne, W P. Staunton

The treatment of preg-robbing gold ores has always been a technical challenge in the gold industry. Early solutions included removal of preg-robbing carbonaceous material by flotation, the addition of kerosene to æblindÆ/passivate the surface of the preg-robbing component, and the most effective of all options, roasting the ore. Unfortunately gold ores have become more complex and roasting has environmental challenges, so other methods of treatment have had to be found. This paper will review methods of characterising preg-robbing gold ores, method of treatment and cite examples of actual application in the industry.CITATION:Dunne, R, Staunton, W P and Afewu, K, 2013. A historical review of the treatment of preg-robbing gold ores - what has worked and changed, in Proceedings World Gold 2013 , pp 99-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J. Gathje

Normal process development for pressure preoxidation treatment of refractory gold ores starts with laboratory batch autoclave tests, followed by operation of a continuous autoclave pilot plant for confirmation of the various process options. This scheme will generally provide good information showing the effects of such variables as grind size, time, and temperature, and will indicate whether autoclave preoxidation will produce solids that are amenable to cyanidation for gold recovery. However, several recent test programs conducted over the last three to four years have shown that the cyanide leaching responses of treated solids from the batch tests can differ considerably from those achieved by the continuous pilot plant autoclave. Examples are provided to demonstrate these differences and to show the importance of extending the laboratory investigations to include the use of a semicontinuous autoclave test procedure. A test case is cited in which this procedure provided data that could not be obtained from batch tests.

Jan 1, 1995

By Walter R. Storms

This paper , which describes the mining methods and costs at the Atwood copper mine in the Lordsburg ( Virginia ) Mining District of Hidalgo County , N. Mex . , is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices , methods , and costs in various mining districts of the United States . The mine and surface plant are situated in the west half of sec . 7 , T. 23 S. , R. 18 W. , about 3 miles by road southwest of the center of Lordsburg , near the old abandoned townsite of Valedon ( see fig . 1 ) . The main line of the Southern Pacific Railroad passes through Lordsburg , as does the paved eastwest U. S. Highway 70-80 . A spur line of the Southern Pacific ends near the mine . A good graded road connects the mine with Lordsburg . The following pages present a brief history of the district , describe the geology , and outline methods of prospecting and exploration, including sampling and estimations of tonnages and values . Development, and mining methods are explained , and transportation , ventilation , drainage ,. safety measures , and organization are described . The wage scale and costs of development and mining comprise the corrcluding sections of this circular .

May 1, 1949

By T Kojovic

"The index A*b, determined from the Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight tester (DWT) results, has become well-known in the mining industry as a reliable measure of ore hardness in impact or crushing, having the inferred units of t/kWh. This index evolved from a long history of comminution studies at the JKMRC, including the development of the now superseded JKTech twin-pendulum, the industry standard JK Drop Weight Tester (JKDWT) and the faster alterative JKMRC rotary breakage tester (JKRBT). A reduced version of the DWT, the semi-autogenous grinding mill comminution test (SMC test®), also provides estimates of the A*b though the testing of only one particle size at five specific energies. Experimental determination of A*b using the above devices/tests requires samples, with sufficient mass, to be sent to designated laboratories, registered to conduct such tests. This protocol is fine for bankable and commercial testing, where material characterisation data is used in conjunction with machine specific data in modelling and simulation, and power based calculations. However, for comparative testing, where results are required at the time of sampling (eg for plant troubleshooting or spot-surveys), or for rapid ranking of geometallurgical samples, these existing tests simply do not provide a timely, viable and cost-effective solution. In order to address this critical void in the realm of comparative testing, a new device has been developed, exploiting a central feature of single particle impact testing – that the A*b can be reliably estimated using one precise low energy test. This device, for which a patent is currently pending, called the HIT (Hardness Index Tester), has been precision engineered to allow users to break narrowly sized fragments at a set specific energy, in a safe and easy manner. The manufacturing materials have been chosen carefully to ensure compatibility with the intended use and portability to any site, whilst minimising cost. The device is supplied with a novel quality assurance / quality control (QA/QC) feature, to ensure that the targeted potential energy is consistently delivered. The product from the HIT breakage test can be quickly sized using a single screen to determine the mass per cent undersize, from which the A*b index is calculated directly at site – eliminating the need to send the raw data off-site for analysis. On presized fragments, a single test using 20 fragments takes less than five minutes to complete, and the results are immediately available. The HIT is currently being tested at a major mining laboratory in the US and the results to date have proved it can deliver on all fronts. This paper describes the new prototype device, which offers users a low cost in-house mechanism for estimating the A*b at any mine site, with potential applications on fragments up to 25 mm from drill core, blast chip rejects or the grinding circuit feed. It also outlines the results of field tests carried out by an objective third party mining group and compares the results with those from current industry standard tests conducted on the same material.Citation:Kojovic, T, 2016. HIT - a Portable Field Device for Rapid Testing at Site, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 9–16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

"The Mine Haul Road Optimization Alliance is an Australian industry-academia collaboration which has been developed to support mine haul road operators by fully integrating mine road design research solutions with industry end-user service providers to design, assess, implement and monitor the various equipment, materials and road management strategies required to optimize the safety, environmental and economic performance of a haul road. Initially, a broad overview of the university-industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis, internationally. This insight places realization of a collaboration between Curtin University Western Australian School of Mines Mining Engineering and Metallurgical Engineering (WASM ME2) and the Haul Road Optimization Alliance (HROA) industry members into context of opportunity. Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry can collaborate to deliver a more robust solution to mine haul road design, performance or management needs, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service-providers alike forms the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and implementable solutions. The paper concludes with examples of how the alliance collaborations work in practice to deliver improved mine haul road designs and optimized operational performance, together with the mechanisms used to ensure industry needs are met through focused, end-user driven research and integrated solutions implementation."

Jan 1, 2016

By M. H. Allan

SASKATCHEWAN POWER CORPORATION is a Provincial Crown Corporation responsible for the production transmission and distribution of electric power and natural gas in the Province of Saskatchewan. Through the electric power responsibility, we became interested in the coal reserves in Saskatchewan, which, although still somewhat of an "orphan fuel" in the early and mid 1950's, gave the promise of providing a low-cost source of energy for electric generation. Coal in Saskatchewan, a lignite with an "as-received" heating value of from 5000 to 6500 Btu's per lb and up to 40% moisture, was first recorded in 1853 . By the end of the 19th century, many small mines were in operation in the Estevan, Coronach and Shaunavon areas supplying local inhabitants with a cheap source of heat. These small mines, some of them prosperous, some of them not, continued operation right up to the late 1940's, when oil replaced coal in the market place. The year 1930, however, saw the introduction of the new technique of strip mining in the Estevan area. This technique revolutionized coal mining. It was now possible to use large machinery to uncover the coal and cast the overburden to one side instead of burrowing through thin seams of coal varying from 2 to 10 feet thick. The overburden cast aside by these large mechanical shovels, or later draglines, created heaps of spoil which at that time, during the depression, were a sure sign of prosperity and the welcome news that people had jobs. By the late 1940's, coal production had dropped off, but the spoil piles remained and were now labelled by some as "scars on the landscape", even though there had been some natural succession of grasses. In addition, some people had planted trees in experimental plots and even some aerial seeding had been done.

Jan 1, 1978

By L. L. Melton, D. L. Lord, B. W. Hulsey

A mathematical model d1.20p/4L = A(8v)8 derived from the Blasius equation is proposed to be applicable to turbulent flow through straight cylindrical pipe for time-independent fluids which produce a diameter family of straight parallel lines on a log (dp/4L) vs log (8v/d) plot or stress-flow diagram. Such a correlation should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable frictional pressure reductions. The Newtonian diameter exponent value 1.20 is shown to be empirically valid for turbulent non-Newtonian flow by application of numerical analysis methods. Multiple regression analysis is applied to a logarithmic linearization of the proposed model. An improved data fit results from further linearization achieved by taking linear terms from a generalized Taylor's series expansion about the multiple regression coefficients. Extensive experimental data obtained in five pipe diameters with water, sodium carboxymethyl-celIulose solutions, guar gum solutions, bentonite clay suspensions and calcium carbonate slurries are presented. Except for calcium carbonate slurries, which were investigated rather than time-dependent cement slurries, the fluids studied contain drilling or fracturing fluid additives. The behavior exhibited by these fluids is considered typical of most fluids encountered in drilling, cementing and fracturing operations. INTRODUCTION Considerable difficulties have been encountered in predicting turbulent flow pressure drops produced by non-Newtonian fluids flowing through straight cylindrical pipe. Correlations previously presented require extensive experimental data which represent several pipe diameters and a wide flow rate range to estimate the necessary scale-up parameters.l-7 One must implement either elaborate experimental apparatus or spend considerable time and effort to gather these data. Presented here is a correlation method which should minimize the experimental effort and data analysis normally required by utilizing flow data taken with only one pipe diameter. Turbulent flow data (up-stream and down-stream pressure and volumetric flow rates) were collected for five pipe diameters through operation of a small pipeline system having an electronic data acquisition and digitizing system. A mathematical model derived from the Blasius equation was utilized to describe the functional relationship between pressure drop and the two independent variables, diameter and average flow velocity. A correlation, which should produce a valid single-pipe scale-up, resulted from a computer-implemented statistical and numerical data analysis for several time-independent non-Newtonian fluids.

By Ruichen Ren, Xu Han, Caixia Li, Zengchuan Yue

In this paper, the size-density distribution of coarse middling coking coal (CMCC) with different grinding fineness and flotation concentrates was investigated. Then, the flotation behaviors and liberation characteristics of different size-density fractions in ground CMCC were analyzed, and the different size-density fractions were divided into five categories: mostbeneficial, secondary-beneficial, poorly liberated, insignificant-pollution, and serious-pollution. Based on the content of particles with different liberation characteristics, an evaluation index of the liberation characteristic of ground CMCC, namely, the liberation perfection index (LPI), was proposed. The results indicated that grinding changed the size-density composition of CMCC, which affected the flotation performance. Insufficient grinding and overgrinding were not beneficial to flotation. Insufficient grinding caused a higher content of poorly liberated particles and a lower content of most-beneficial particles. Overgrinding increased the content of serious-pollution particles and reduced the content of most-beneficial particles. The size order of the LPI values of different ground CMCC was consistent with the flotation efficiency, and the LPI values of the other two similar samples were overall positively correlated with their flotation performance, suggesting that the method is universal.

Feb 14, 2023

By Harvey N. Davis

MUCH has been written and said during the last twenty years about the place of the engineer in modern life, about the fundamental role that he plays both in developing and in maintaining the material foundations of modern civilization, about the advantages, and also the dangers, of the machine age that he has inaugurated, about the Frankenstein problems that he has unconcernedly foisted upon a generation utterly unable to cope with them, and about the obligation that rests upon him to stop inventing machines and turn his almost legendary energy and skill to inventing institutions that will constitute a solution of the problems he has raised, and contrariwise about his utter inability to offer wise or useful counsel in fields outside the narrow boundaries of his technical training.

Jan 1, 1938

By A. J. Hofmann, G. P. R. van der Merwe, J. E. W. Holm

"A new approach is proposed to perform relativistic comparisons between alternative operational risk management solutions by taking into account the impact of each operational activity on overall system performance. A specific case study, to which this new approach is applied, involves the deployment of safety systems in underground mining operations. Conflicting objectives to be satisfied are the minimization of risk to human lives and the minimization of production losses. As the focus in this case is primarily on the mitigation of risk, the approach that was applied is referred to as activity-based risk (ABR) analysis. Existing development process and risk management methods used in the South African mining environment were analysed by means of observations, a case study, technical documentation, and literature review. It was evident from this analysis that a discontinuity existed between the acquisition and operational phases in terms of the management of safety risk in the acquisition of electronic safety equipment when viewed from a full lifecycle perspective. This discontinuity could be addressed by defining a risk perspective in the system development phase by employing ABR in the preliminary design phase of a system’s engineering life-cycle. The focus of the ABR system development process is to find the functional definition and configuration of safety equipment that addresses both safety and productivity when taking into account human performance variability. In doing so, a balance between productivity and safety is found in a relativistic sense. IntroductionIn any system life-cycle, two major phases exist, namely system acquisition and operation (including maintenance). A distinction is made between acquisition and procurement, where acquisition includes system development and integration as specific engineering activities. In the development phase of a new system, conceptual design, preliminary design, and detail design phases follow in this order to define a complete system, after which the system is put into production and implemented in an operational environment—these activities chronologically define system acquisition in the context of this paper. It is not uncommon that differences exist between the risk management perspective during acquisition of a system and risk management perspective during operation, where nontechnical aspects are often ignored during acquisition, but are then encountered and found to be problematic during operation (Leveson, 2012). These differences also exist in the mining industry."

Jan 1, 2017

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

By D. H. Pulling

Statistics for copper consumption from various sources show that the importance of production from secondary sources is increasing. This is of particular significance in countries such as the U.K ., which are totally dependent on secondary material for the supply of home-produced copper . A brief survey of the U.K . industry has shown that, in the past, relatively high profit margins have not encouraged high cap ital investment and development of more sophisticated operating techniques, but set against a background of rapidly escalating operating and energy costs , together with an ever-increasing demand for copper , it is anticipated that the industry will see great changes in the near future. With this in mind, an experimental furnace for continuous smelting of copper-bearing scrap has been developed at the University of Birmingham. This furnace has been designed to combine the conventional operations of blast furnace or reverberatory smelting, usually followed by converting, in one unit, and incorporates many of the features of the WORGRA and Noranda processes for continuous primary smelting . It consists of a long, sloping channel, constructed of chrome-magnesite refractory, which: is churned near the top. Smelting is effected lower down the channel, where iron, etc., in the scrap is oxidized and slagged off with silica flux. Provision is made for oil injection to increase oxidation rates. Metal can flow from the bottom of the channel, and slag from the top, so that a counter-current flow is achieved. The approximate molten capacity is 25 kg. Various scrap charges, both synthetically made and as supplied from various industrial smelters, have been successfully smelted. Metal of 83 -95 % Cu has been produced, depending on the original charge composition and the degree of air injection, although air injection was also found to considerably increase the copper loss to slag. Recoveries of other valuable non-ferrous metals in the charge were good.

Jan 1, 1977

By M. E. Tyrrell

This Bureau of Mines investigation was made to determine the possibilities of using Florida beach-sand concentrator wastes in ceramic products. Sands used in the investigation originated in the Trail Ridge area of Florida, where continued operation of processing plants for recovering titanium minerals promises a dependable source of raw materials. Three general classes of ceramic products were studied, namely: (1) Structural, (2) refractory, and (3) electric-furnace slags.

Jan 1, 1956

By P. P. Rosario

A research project was conducted at the University of British Columbia (UBC) resulting in the development and evaluation of a novel comminution circuit incorporating autogenous grinding and parallel trains of cone crushers and high-pressure grinding rolls (HPGR). A primary driver for the circuit was to treat ore from deposits with clay and variable hardness. This paper summarizes the unique pilot-plant test program that was developed as a basis for experimental simulation and lists the main findings of the research, including the circuit?s potential operational cost savings compared to a conventional SAG circuit.

Jan 1, 2012

By R. E. Sundell, S. M. Correa

"A mathematical model is developed for the fluid flow in tungsten-inert gas weld pools. The fluid is taken to be incompressible, viscous, electrically conducting, and confined within a pool of specified shape. The flow is driven by surface-tension gradient (thermocapillary), electromagnetic, and buoyancy forces generally in this order of importance. Analysis indicates that the electromagnetic field may be calculated a priori and so decoupled from the nonlinear fluid mechanics and heat-transfer problem. The resulting set of equations is solved numerically by a line relaxation process. Computational errors caused by truncation in finite-difference schemes and by inadequate grid distributions are considered. The model is used to study several cases of differing heat and current input to the pool with and without surfactant-induced thermocapillary forces. The principal conclusions are that the thermocapillary flow, when present, is dominant with surface velocities on the order of 1 m/s. The heat transfer, as deduced from isotherms within the pool, is crucially dependent on the flow. Also, flow velocities and weld-pool surface temperatures were measuredand agree well with the model.2. IntroductionThe requirements of improved control and of automation in the TIG (tungsten-inert gas) welding process have led to the development of mathematical models for the heat transfer to the workpiece. It is now widely recognized that the fluid flow in weld pools sufficiently distorts the conduction heat transfer pattern to warrant inclusion in a process model. The experiments of Woods and Milner (1), among others, demonstrated that TIG weld pools could be driven by the electromagnetic J x B body forces present, J being the current distribution and B the induced magnetic field. Atthey (2) calculated that in typical pools the buoyancy force was about an order of magnitude less important - despite the large temperature gradients present - and neglected it in a computational study of the magnetohydrodynamic (MHD) flow. This work also reviewed many earlier studies of MHD flow caused by a source of current at a fluid surface, including analytical studies by Shercliffe (3), Sozou (4), and Sozou and Pickering (5), and a numerical study by Andrews and Craine (6). These works establish the importance of the electromagnetic force in the weld-pool flow."

Jan 1, 1986

By D Hatton, S Wilson, F Orrante, M Taghimohammadi, F van der Walt, N Arslan, M Westcott

"Cayeli Bakir Isletmeleri is an underground copper-zinc mine in turkey. The ore is highly variable with feed grades ranging from 1–4 per cent copper and 1–10 per cent zinc. Due to this variability, ore characterisation and blending strategies are crucial for performance optimisation.This paper presents a case study for a multidisciplinary approach to process optimisation, integrating Geometallurgical and advanced control methods to achieve optimised plant performance. The results from comprehensive metallurgical tests and surveys were used to develop a mathematical model utilising SGS’s Integrated Geometallurgical Simulator® (version number 2.5.24.0). The model was employed to determine the most appropriate operational settings required to ensure that optimised grades and recoveries are achieved for each ore type.SGS’s Modular Expert Technology (MET) expert system was then implemented to target these optimum operational ranges utilising online grade and froth velocity measurements. The successful conversion and deployment of the modelled process parameters into an expert system has resulted in significant improvements in overall recovery and circuit stability.Citation:Arslan, N, Westcott, M, van der Walt, F, Hatton, D, Taghimohammadi, M, Orrante, F and Wilson, S, 2016. A Multidisciplinary Approach to the Optimisation and Control of a Copper-zinc Grinding and Flotation Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 115–122 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By H. Matsuda, T. Iwashita, H. Awata, H. Liwei, D. Hirabayashi, Y. Saito, S. Ozawa, Y. Goto

"The present study is concerned with investigating the effect of chemical treatment on enhancing the HCl absorption capacities of coal burnt ash and slag. It was found that the HCl absorption capacity of coal burnt ash discharged from fluidized bed combustor was improved by hydration with water and 5% polyethylene glycol solution. This phenomenon was based on an increase of the specific surface area of treated coal burnt ash. The HCl absorption capacity of hydrated ash with polyethylene glycol solution was almost equivalent to that of standard CaO and Ca(OH)2. In particular, the specific surface area of hydrated ash with polyethylene glycol solution was found to be 19 m2/g, which was more than over eight times larger than that of raw sample. Hydrated slag treated with lON sodium hydroxide solution also showed high HCl absorption capacity, with highly improved surface area. It was found that the absorption capacity of slag for HCl depended on the treatment time, showing the maximum absorption capacity for 12 hours of hydration treatment.IntroductionA large amount of coal burnt ash, slag and dust are discharged from such industrial processes as coal combustion and metal refinery etc., and it becomes an serious problem to recover and diminish these solid wastes because of the shortage of dump sites and subsequent metal elution to the environment. Figure 1 shows the present situation of reutilization of coal burnt ash and slag in Japan [1,2]. It is shown in this figure that these solid wastes are recycled as materials in the fields of earthwork, agriculture and forestry etc. A part of these solid wastes, however, is still dumped to landfill. To decrease this dumped amount, the development of environmentally friendly reutilization technique for these solid wastes is of great importance."

Jan 1, 2000