Search Documents

By J Safarian, M K. Kar

Bauxite residue is one of the most important by-products from the alumina industry with no commercial use till now. The utilisation of bauxite residue through pelletising with different lime additions, hydrogen reduction, and smelting has been studied in this work. Three different types of green pellets were made with varying calcite-to-bauxite residue ratio and subsequently sintered at elevated temperatures. The sintered pellets were isothermally reduced at 1000°C under hydrogen gas followed by smelting of the reduced pellets in argon at 1500°C. Smelting of the reduced pellets leads to the recovery of metallic iron and the formation of a leachable calcium aluminate slag. X-ray diffraction (XRD) and scanning electron microscope (SEM) were used to characterise the phases and microstructural analysis. The iron produced in the smelting process has a high purity, above 99.5 wt per cent. While the iron content of the slags is quite low, and the slags shows variations of krotite (CaAl2O4), gehlenite (Ca2Al2SiO7), and perovskite (CaTiO3) phases based on the variation of calcite addition. It was found that the more calcite addition in pelletising yields higher percentage of krotite phase as compared to lower calcite-containing pellets. Employing quantitative XRD analysis, the krotite phase fraction was found approximately 85 wt per cent for higher calcite-added pellet, and around 74 wt per cent for lower calcite-added pellet. FactSage™, ver 8.1 (Thermfact and GGTTechnologies) thermodynamic software was used to evaluate the obtained experimental data, they both revealed that the

Jun 19, 2024

By Tyler A. Dawson, Ryan P. Butler, Timothy Gualandri, Jason R. Edberg

"In the early 1920’s, the City of Tulsa, Oklahoma constructed an approximately 8,238-foot long tunnel, the Tiawah Tunnel, through bedrock. Voids behind the concrete tunnel liner were detected via probe drilling in early 2000 as part of an interior visual condition assessment. In 2012 and 2015, conditions along the entire tunnel were efficiently assessed through geophysical investigation using ground penetrating radar (GPR) along the inner tunnel crown and at various select locations within the tunnel. Fifty-seven (57) potential voids, extending up to 19 inches in depth and 12 feet in width, were detected with 1,000 MHz GPR and confirmed through probe drilling with approximately 80% accuracy. GPR proved to be an efficient and reliable technology for void detection behind concrete tunnel lining. This paper highlights the geophysical investigation and how geophysical efforts were combined with other investigation efforts to definitively determine the presence of voids outside of the tunnel lining.INTRODUCTION The city of Tulsa, Oklahoma has a population of about 400,000 people. The original source of water for the city was the Arkansas River. The first pumping operation provided untreated water to homes and businesses in 1904. The residents of Tulsa found this water to be unacceptable due to the high levels of salt and gypsum present. As the city grew, land and storage/treatment facilities were acquired in order to obtain and distribute a more suitable raw water. The raw water needs for the city are currently satisfied by transport and treatment of about 100 million gallons per day (MGD) of water from surface water sources. Water is transported many miles from Spavinaw/Eucha and Oologah lakes to Yahola Lake and the Lynn Lane Reservoir (totaling over 3-billion gallon capacity). From here, the raw water is treated and transported to the various customers (City of Tulsa 2015). The Tulsa Metropolitan Utility Authority (TMUA) is responsible for the operation and maintenance of the raw water transport system."

Jan 1, 2016

By Muammer Kaya

This paper reviews the existing and state of art knowledge for electronic waste (e-waste) recycling. Electrical/electronic equipments (EEEs) which are unwanted, broken or discarded by their original users are known as e-waste. The main purpose of this study is to provide a review of e-waste problem, give e-waste management strategies and introduce various physical e-waste recycling processes with special attention towards extraction of both metallic values and nonmetallic substances. The hazards arise from the presence of heavy metals (e.g. Hg, Cd, Pb etc.), brominated flame retardants (BFRs) and other potentially harmful substances in e-waste. Due to the presence of these substances, e-waste is generally considered as hazardous waste and may pose significant human and environmental health risks if improperly managed. This review paper describes the potential hazards and economic opportunities of e-waste. First of all, an overview of e-waste/printed circuit board (PCB) components and substances are given. Current status and future perspectives of e-waste and waste PCB recycling techniques are described. E-waste characterization, dismantling, liberation, classification and separation processes, are also covered. Manual selective dismantling after desoldering and metal-nonmetal liberation at −150 μm with two step crushing are seen to be the best techniques. After size reduction, mainly physical separation processes employing gravity, electrostatic, magnetic separators etc., which are commonly used in mineral processing, have been critically reviewed here for separation of metals and nonmetals. The recovery of pure metals from e-waste after physical separation can be performed by pyrometallurgical, hydrometallurgical or biohydro metallurgical routes, which are not covered here. Suitable PCB recycling flowsheets for industrial applications are also given. E-waste recycling will be a very important sector in the near future from economic and environmental perspectives for both developing and developed countries. Recycling technology aims to take today’s waste and turn it into conflict-free, sustainable polymetallic secondary resources (i.e. Urban Mining) for tomorrow. Recycling technology must ensure that e-waste is processed in an environmentally friendly manner, with high metal/nonmetal recovery efficiency a lowered carbon footprint. Taking into consideration our depleting natural resources, this Urban Mining approach offers quite a few benefits; it provides a substantial secondary resource, while also ensuring that the environment is kept free from harmful toxins in e-waste. This results in increased energy efficiency and lowers demand for mining of new raw materials.

Mar 1, 2017

By E. Ghali, N. Sorour, G. Houlachi

"The binary Fe53Mo47 and ternary Fe54Mo30P16 coatings have been electrodeposited from citrate-based electrolyte on mild steel (MS) substrates. The electrodeposition has been conducted for 6 hours at 20 mA cm-2 and 30°C. The electrochemical tests were carried out in chlorate solutions containing 300 g L-1 NaCl and 4 g L-1 K2Cr2O7 at pH 6.4 and 80°C. A number of surface characterization techniques such as SEM-EDS, XRD and EMP were used to study the microstructure of the alloys. The electrocatalytic activity of these coatings was investigated using steady-state polarization and galvanostatic technique. This study revealed that the Fe-Mo-P coating could be considered as a promising cathode material for the hydrogen evolution reaction (HER). The results showed an important decrease of hydrogen overpotential for Fe-Mo-P alloy as compared to that of Fe-Mo and especially MS which is a traditional cathode in chlorate industry. The HER overpotential for Fe54Mo30P16 at current density of 250 mA cm-2 was decreased by 30% in comparison to that of MS (1029 mV), and by 16.5% to that of Fe53Mo47 coating (857 mV).INTRODUCTIONSodium chlorate is used for manufacturing of several daily consumption products. This chemical is mainly employed for the production of chlorine dioxide (ClO2) that is a bleaching agent used in the pulp and paper industry. The ClO2 is also consumed for generation of perchlorates, chlorites and other chlorates, as an herbicide and in uranium processing (Cornell, 2002). Sodium chlorate is produced industrially via following overall formula in un-divided electrochemical cell (Nylén & Cornell, 2009):"

Jan 1, 2016

By William Daly

THE application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable.

Jan 1, 1934

By William Gleason

While a fleet of 100 t (110 st) haul trucks were busy removing overburden from the open pit mine in the distance, a host of dignitaries, including congressmen and California state representatives, gathered for Molycorp?s official groundbreaking ceremony at the Mountain Pass Mine on April 20. The mine, recognized as arguably one of the richest rare earths deposits in the world, is at the center of Molycorps? strategic ?Mine to Magnets? plan. It aims to secure America?s future supply of rare-earth-dependent technologies by developing a strong domestic rare earth industry. Molycorp identifies rare-earth-dependent technologies as those that cannot be produced without rare earth materials. The list of these technologies is long and growing. It encompasses everything from personal electronics and batteries for hybrid cars to permanent magnet generator wind turbines and national defense applications.

Jan 1, 2011

By T van Niel, M Trefry, B Baker, I Rea, A Hawdon, D McJannet, D Boadle, R Fandrich, A Littleboy

Many open cut mines extend to depths well below the natural water table level with constant dewatering required to maintain operations. When mining activities cease the groundwater starts to fill the void and pit lakes form. The resultant pit lake is directly connected to the surrounding water table and understanding the hydrological and chemical evolution of these lakes is important for minimising environmental impacts. In Western Australia alone there are currently 1800 mine voids and more than 150 mines operating below the water table (Johnson and Wright, 2003). In conjunction with BHP Billiton Iron Ore, CSIRO has been undertaking research to measure and model rates of evaporation from pit lakes in the Pilbara region of Western Australia. Extreme high temperatures and low humidity ensures that this region experiences the highest evaporation rates in Australia.CITATION:McJannet, D, Hawdon, A, Boadle, D, Baker, B, van Neil, T, Littleboy, A, Trefry, M, Rea, I and Fandrich, R, 2016. Measurements and modelling of evaporation from abandoned mine pit lakes, in Proceedings Life-of-Mine 2016 Conference, pp 106–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J. A. H. Church

The report is too voluminous to be considered in detail within the scope of a single paper, so I will confine my consideration of it to the broader aspects, leaving other members to deal with points of particular interest. The method of presentation leaves one with an uneasy sense of prolixity and confusion of thought; the foreword by the Chairman may well be accepted as a true index of the whole. His argument amounts to this: Recognizing at the outset the futility of divided counsels, it was deemed advisable to arrive at unanimity. To this end, some members subscribed to views to which they do not whole-heartedly assent, thus giving weight to conclusions with which they were at variance. Unanimity cannot be qualified-either it exists or is absent-and, moreover, in the text of the Com-mission I can find no word that unanimity is required. Surely it would have been preferable to have a unanimous report covering such aspects as were acceptable to all members, with minority reports by individual members on such other aspects as were controversial, leaving it to the Government to give such weight to the divergent views as the personality of their sponsors might warrant. In the final analysis the value of an opinion varies directly as the personality of its exponent.

Jan 1, 1926

By David E. Hyatt

The chemical attributes of cyanides have long been exploited in ore pro- cessing schemes for the recovery of copper, molybdenum, gold, silver, and other metal values. Blast furnacing operations are significant unintentional producers of cyanides which find their way into process waters. Many of the more than 20,000 electroplating facilities in the United States utilize cyanide plating baths and generate cyanide containing wastes. As social, political, and economic pressures for water quality attainment, maintenance, and preservation grow, the requirements for the development of treatment technology to control cyanide levels in wastewater become increasingly apparent. Just as the chemistry of the cyanide ion 1s an integral part of its industrial applicability, so must this chemistry be a fundamental part of any decomposition or removal technology used to control its level in effluent or recycled waters. The complexity of this chemistry is substantial and it cannot be considered in a superficial or cursory manner if control system design is to be both efficient and reliable.

Jan 1, 1975

By Raymond S. Shrode

Transportation is one of several important increments in the total market cost of most commodities. On a national average it has been reported that transportation accounts for about 25% of the total cost of a product at the market place. And industrial minerals are no exception. In fact, the proportionate cost frequently exceeds the 25% average. Further, it may actually determine the economic value of a deposit. Transportation may possibly be thought of as a specialized subject of concern only to a traffic manager and of only nominal interest to the mining engineer, the geologist or other technically oriented member of mineral producers' staff. However, in the industrial minerals field, interest is not commonly confined to exploration, development, production or marketing, but is in contrast an overlapping one. In a very real sense this broad area of interest in the total economics of the business is the specialty of the industrial minerals man. And transportation is a vital part of the total picture. Comments in this paper deal with rail transportation.

Jan 1, 1969

By H. G. Papacek

The Fabrica Mine of the Brazilian iron ore company Ferteco mines on an extremely inhomogenous ore deposit. A large amount of the crude ore consists of fines minus 100 micron which cannot be sold without further treatment because of its chemical and physical properties. In order to make full use of the mined crude ore an expansion program has been realized which incorporates among others a concentrator to produce classified blast furnace ore , sinter feed and pellet feed. The pellet feed is converted in a 2.5 million tons per year Lurgi Dravo plant into high grade pellets. The paper discusses the selection of the concentration process, the pelletizing process and describes the experiences with the operation plant during the startup and the first years of operation.

Jan 1, 1979

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine (CM) with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. This paper describes the validation of the models based on experimental data and the gas distribution results of the CFD models. INTRODUCTION To control methane gas and dust concentrations on continuous mining operations, it is important to provide sufficient quantity of fresh air from the end of tubing or curtain to the active face. In this region, operating machine-mounted water sprays and fan-powered, flooded bed scrubbers can significantly increase the amount of airflow reaching the face [1-3]. However, when an entry is large, especially in higher coal seams, the water spray configuration and the scrubber capacity may not be adequate to maintain sufficient forward airflow to confine the dust cloud to the face. Dust can roll back toward the machine operator as a result [4]. Currently, several coal mines having negligible gas emissions in higher coal seams (2.4 to 3.0 m [8 to 10ft.] thick) with exhaust tubing systems redirect the scrubber discharge back towards the face in an effort to improve dust collection. NIOSH studied the redirected scrubber exhaust techniques for dust and gas control in a full scale CM gallery to assess its potential for industry-wide application [5]. For a CM face, previous studies have concluded that the behavior of gas and respirable dust is a complex process. The distribution/dispersion and transport of gas and respirable dust after they are liberated at the face are governed mainly by their mass properties, the movement pattern of the ventilation air, and interactions with the mining machine and water droplets created by the external water spray systems used for dust control [6-10]. To understand these behaviors in a complex CM environment and to evaluate the effectiveness of various control techniques, numerical modeling has become a necessary supplement to laboratory experiments and field studies."

Jan 1, 2017

By R. W. Smith

The Bureau of Mines is engaged in systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy that will facilitate the theoretical study of flame and combustion phenomena. This report is the second of a series3/ presenting results of the study for particular fuel-oxidant sys tans. These calculations had as their objective evaluation of the constant pressure flame temperatures of methane-air and propane-air flames at atmospheric pressure as functions of the mixture ratio and inlet temperature of the fuel-air stream.

Jan 1, 1953

By A. L. Mular

Some specific cases of the collection of data from industrial grinding and classifying operations, and the development of models from the data so obtained, will be described. The problems encountered, the effort involved, and the value of the derived models in improving the plant efficiencies will be discussed and documented where possible.

Jan 1, 1971

By J. Kretschmann, O. Drusche, S. Krause

Mining companies are caught between the growing international relevance of ESG (Environmental, Social and Governance) investments and the need to secure their “social license to operate” by considering the needs of their stakeholders. In the search for sustainable business models, the concept of the circular economy (CE) is gaining momentum among practitioners and scholars, as it enables the creation of shared value and thus strengthens the trust of investors and stakeholder relationships. However, there is a lack of a sectorspecific CE framework providing guidance to decision-makers in evaluating promising activities. A gap, which this contribution aims to address.

Mar 2, 2022

By William M. McKewan

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Ropes of sizes ranging from 3/4 to 2 in. in diameter and from 2 to 35 ft in length were tested to determine their breaking strength, elongation, and torque. This was done to characterize the test equipment on ropes used in mine hoisting systems.

Jan 1, 1990

By M. Pope

By 1950, packaged oil and gas fired boilers were on the market for capacities up to 30,000 lbs./hr. By 1962, capacities were up to 100,000 lbs./hr. and even higher when separate heat traps (economizers and air preheaters) were attached to the boiler packages. During this period, complete packaged coal fired boilers were developed into the 10-15,000 lbs./hr. range. Oil and gas fired plant designs became very compact, "basementless", and far: less costly than the coal fired plants of any capacity. Coal fired plants remained large and expensive, required field erection of boilers and required basements. With the spectacular strides made in automation, oil and gas plants became far less costly to operate, requiring only the part-time attendance of a single operator. Some advances were made in coal fired plants, but not to the degree attained by the fluid fuel competition.

Jan 1, 1965

By D. Watson

The Henderson mine has more than 20 years experience and has placed a combined total of more than 400,000 m3 (520,000 cy) of shotcrete and concrete. Over the last 20 years the mine has used a variety of equipment for placing concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Henderson has recently received a state of the art wet shotcrete placer, automated its batch plant, fabricated a mobile concrete form jumbo and is soon to receive a new concrete transport truck.

Jan 1, 1992

By E. E. N. Smith

"Uranium exploration by Eldorado prospectors north of Lake Athabasca began in late 1944 and resulted in initial discoveries in 1946 in the Beaverlodge region with mill production starting in early 1953. The operation was closed in mid-1982 having produced 21,457,947 kilograms U30 8 from the Eldorado FayVerna mine, Eldorado satellite operations and from other district producers on a custom basis.The Fay- Verna mine consists of pitchblende-brannerite orebodies spatially associated with both sides of a regional eastwest structure, the St. Louis Fault. The orebodies in the footwall (Fay) are elongate deposits of two types raking steeply to the southwest along the 50 degree south dip of the fault.One type consists of networks of fractures and veins filled with pitchblende, calcite and quartz in chlorite, epidote-altered mylonitized mica schists and amphibolites of the Middle Aphebian Tazin Group. The other type is comprised of fragments of mylonitized metasomatic quartz-feldspar granite of Late Middle Aphebian age cemented with a matrix of pitchblende, brannerite, calcite and some quartz. The vein networks lie en echelon in the footwall of the breccia ore bodies which, in part, are capped by the mud gouge of the St. Louis Fault; in other places, the breccia orebodies are overlain by basal conglomerates, grits and arkoses of the late Aphebian Martin Formation which itself immediately underlies the plane of the fault.Orebodies in the hanging wall (Verna) are a series of irregular, tabular deposits lying within a tightly overturned syncline of Tazin mica schists, amphibolites and siliceous mylonites. They consist of pitchblende, calcite-filled fractures grouped into zones and deposits displaying stratabound habits within individual rock types.Also described are several Eldorado satellite properties which were significant producers of uranium and which display complementary geology to that in the Fay- Verna mine.In general, uranium deposits in the Eldorado Beaverlodge region are closely related to minor structures associated with major faults. Uranium appears to be best concentrated where the rocks are well mylonitized and brecciated. Pitchblende fills networks of veins and fractures in metasediments and metavolcanics as well as matrix material cementing brecciated, mylonitized granite. All deposits in the Beaverlodge region lie in close proximity to the unconformity between the Martin Formation and the underlying Tazin Group."

Jan 1, 1986

By D. S. Salonine

Aluminum alloys are widely used in modern industry. Tubes and hollow shapes give great opportunities for structural purposes as well as fluid transport due to their stiffness and lightness, Extrusions on a mandrel or through a bridge die, that requires splitting of the billet with re-welding, produce hollow shapes with varied contours, fins and multiple cavities. Moving and stationary mandrels, mandrel lubrication, tooling for ribbed-tube heat exchangers, and for drilling pipes are considered. Bridge dies can be classified by the bridge position relative to the die face, by mandrel support structure, and by assembly type, The main parameters influencing the quality of the die-welded seams are considered, The difficulties of extruding various alloys through bridge dies are discussed in terms of metallurgical factors, Some approaches to the calculation of the stresses in a bridge are presented.

Jan 1, 2005