Search Documents

By John Hays Hammond

IT was but a few years ago that the mining engineer, and his confreres, the civil, mechanical and electrical engineer, were stigmatized by politicians of the parish? pump variety as advance agents of unprincipled exploiters of backward countries. Today he is recognized as a most important missionary of civilization in opening up new territory to contribute its mineral wealth and incidentally its other resources for the needs of mankind. An engineer, it is now conceded, is not only a benefactor of the world at large, but is a primary factor in the betterment of conditions of the inhabitants of those countries developed by his skill and indomitable courage-for courage is requisite in pioneering and his indefatigable industry. The engineer will, I believe, become a real "Ambassador of Good Will," when the slow-consenting academic mind realizes as it must that beneficent deeds are more enduring and more convincing than mere gestures of professed amity.

Jan 1, 1929

By Farrel W. Lytle

An X-ray emission spectrographic method of analysis is presented for determining rare-earth elements in fractions obtained from bastnaesite ore. The method includes determination of yttrium, thorium, lanthanum, and the rare-earth elements in various complex mixtures. The analysis technique is based upon comparing the samples with synthetic standards approximating the composition of the samples. Working curves are plotted on an absolute-intensity basis, with no correction for back-ground. Examples of working curves and the analyses of typical rare-earth concentrates are included. The selection of spectral lines for the various sample matrices is discussed. A special technique is used for samples in which rapid hydration and carbonation occurred. By analyzing synthetic samples of known composition, the accuracy of the method was determined. The average error of analysis was about 3 percent of the amount present in the range from 5 to 100 percent and about 7 percent in the 0.2-to 5-percent range. A maximum of about 40 samples per day may be analyzed for 7 elements each.

Jan 1, 1957

By Christopher J. Bise

It is somewhat reassuring to note that the United States has an abundance of coal reserves which can be used to bridge the widening gap between the nation's energy production and consumption. The U. S. Bureau of Mines has recently established a demonstrated coal reserve base of 434 billion tons. (31)(Figure 1) As can be observed, the major percentage of the reserves is in the West. Although surface coal mining in the West has been gaining increased attention in recent years, western reserves that must be deep mined are significantly greater. Though deep mining activity in the west is very limited and accounts for less than 2% of the annual production, the primary reason, quite probably, is the greater thickness of the seams as compared to those found in the East. Forty-five billion tons of the western demonstrated coal reserve base for underground mining are in seams greater than 10 ft. in thickness. (37) Thick coal seams do not lend themselves readily to extraction with the underground mining methods practiced in the United States today. Experiences from the practices in other countries can serve only as guidelines. Consequently, a concerted effort is necessary to overcome the technical difficulties.

Jan 1, 1975

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022

Mining had a very considerable effect on the country's development. The visual evidence remaining is an integral part of New Zealand history. Early mining for manganese and copper in the 1840s was succeeded by alluvial gold rushes. These gave way to hard rock extraction, hydraulic elevation and dredging. Coal mining dating from the 1850s was fairly widespread. Other minerals were obtained on a small scale. Manufacture of mining' machinery stimulated industrial engineering enterprises. Schools of mines played a significant part in advancing technical skills and several remain as museums. Surviving mine structures and site relics are part of the industrial heritage signifying the technological and economic development of a small isolated nation. Some of these are described. Identification, recording and preservation where practicable is advocated.

Jan 1, 1990

Mining had a very considerable effect on the country's development. The visual evidence remaining is an integral part of New Zealand history. Early mining for manganese and copper in the 1840s was succeeded by alluvial gold rushes. These gave way to hard rock extraction, hydraulic elevation and dredging. Coal mining dating from the 1850s was fairly widespread. Other minerals were obtained on a small scale. Manufacture of mining machinery stimulated industrial engineering enterprises. Schools of mines played a significant part in advancing technical skills and several remain as museums. Surviving mine structures and site relics are part of the industrial heritage signifying the technological and economic development of a small isolated nation. Some of these are described. Identification, recording and preservation where practicable is advocated.

Jan 1, 1990

The dielectric properties of practically all oxide and sulphide ore minerals are such that they heat rapidly when irradiated with microwaves particularly at the standard frequency of 2450 MHz. The presence of carbon or low rank coal mixed with the minerals still further enhances the heating rate. Amongst the patented technologies being investigated are: (i) the direct reduction of oxides with or without carbon included in the pellets or briquettes; (ii) microwave precursor heating of composites ahead of smelt reduction; (iii) microwave smelting of ore or concentrate mixtures with carbon, sometimes assisted with oxygen. Microwaves appear to stimulate endothermic reduction reactions as readily as they do exothermic oxidation reactions. Being a method of achieving "bulk" heating, composites or columns of ore-char blends rapidly heat throughout rather than from the outside inwards as in conventional heating. The microwaves of themselves do not generate any gas - the only gases to be cleaned are the products of reaction in the composites or blends, plus the products of oxygen smelting. In the case of sulphide composites, depending on the quantity and type of low rank coal or char present, sulphur may be eliminated, and collected, in the elemental form. Furthermore, reactions seem to take place at lower temperatures than in conventional smelting but no doubt at the "points" where actual reactions are taking place the atomic or molecular vibrations are such as to satisfy the laws of thermodynamics. Examples are given of the production of unusual products of smelting sulphide concentrates and also the alloys produced from refractory minerals such as chromite and ilmenite. The techniques have been used to produce products with as wide a range of melting points as relatively pure tin and tungsten-molybdenum alloys. Special equipment is being designed and evaluated for these new fields of pyrometallurgy.

Jan 1, 1989

By H. J. Glass, J. G. L. Bekkers

"In order to determine the feasibility of a hydraulic ore hoisting installation, the optimal operating conditions were calculated for applying such a system at the Detour Lake Mine of Placer Dome Ltd. Next, a financial analysis was conducted in order to estimate the cost per tonne for hydraulic hoisting of the ore. Subsequently, the cost per tonne was compared with the hoisting costs associated with a new borehole hoist. Installing a hydraulic ore hoist at Detour Lake Mine was found to be feasible with considerably lower costs per tonne of ore. The applied research method appears to be very functional and can be used to do similar research for other mining operations. IntroductionThe principle of hydraulic ore hoisting is well known, yet hardly accepted in hard rock mining. Application of the system would result in a smaller diameter shaft requirement and a flexible, easily expandable system. However, underground ore size reduction might be necessary and practical experience with the system is limited. Following recent innovations in the field of pumping hardware, e.g. new GeHo and Siemag Transplan equipment, hydraulic ore hoisting should be seriously considered for certain mining operations. As a case study, a design was made for the development of the newly found QK-Zone at Placer Dome Ltd.’s Detour Lake Mine. Hydraulic ore hoisting has been compared with conventional skip hoisting by establishing the optimal operating conditions and pumping equipment requirements for similar capacities at a selected mining operation. Generally accepted equations for slurry transport were used to predict the variation of pressure and power requirements as a function of hourly production and pipeline diameter. These data are used to select suitable equipment and estimate cost figures in order to make a financial assessment."

Jan 1, 1998

By R. S. Shoemaker, F. W. McQuiston

REFINERY SECURITY "Highgrading, " a polite word for stealing gold and silver, has been a way of life since the metals in native form have been mined or produced. Unfortunately, in the past, highgraders were not always severely prosecuted or even looked upon unfavorably in their communities. Recent high metal prices with attendent world wide publicity, however, has made highgrading or thievery again a serious problem in mines and plants. When a small button of gold the size of the end of ones little finger has a value equal to about one week's wages, the safe-guarding of gold production by enforcing tight security measures becomes a prime responsibility of management. The higher the gold price, coupled with unrestricted owner- ship, the greater the temptation to “get-your-cut”, and diligence by management must become an integral part of plant security. Primary security begins by knowing the expected gold production and the sampling of a gold ore mill feed for this determination has proved not reliable. However, solution flows can be accurately sampled and measured thereby closely predicting the gold recovered each day as precipitate. The progressive record of total ounces of gold contained in the precipitation press, referred to in cyanidation plants as I1solution calll1 predicts the accumulated production. The "callH is an important adjunct to security and extreme caution must be used so that the pregnant solution meter and sample are confined in a security area. It should be recognized that this key sample may be the target for Ifdoctoring" by trusted insiders (assay office employees) as a preliminary step for stealing precipitates and/or metal. Security measures similar to the following were adopted after one operation experienced a sizeable theft of gold precipitate and metal by trusted employees. The refinery area where precipitates are handled and melted to bullion and all other gold products are kept should be completely enclosed with a tight security fence preferably of solid construction. Access to this enclosure should be through one of two electrically controlled gates, one for personnel and another for occasional truck entrance. Admittance should be restricted to essential personnel who are required to sign a register in and out with the date and time. I£ there is a "back gate" to the restricted fenced area, it should remain locked except in an emergency and then opened only by a supervisor. Television monitoring cameras viewing the gate entrance and other sensitive areas connected to a viewing screen located in the general office afford visual observation at all times.

Jan 1, 1975

By H. X. Li, A. Correa, M. M. Zhang, W. Xuan, M. Andrade

"With increasing demand for steel and depletion of high-grade iron ore deposits, more research efforts are being directed toward extending the life of existing ore reserves and developing technology to treat low-grade iron ore resources. Among all the reported technologies, biotechnologies in mineral processing – specifically bioleaching and microbially induced flotation – have emerged to be considered as low-cost, environmentally friendly potential alternatives to many of the current mineral processing techniques. This paper provides a comprehensive review of current research on the use of microorganisms for iron ore beneficiation and, further, discusses the applicability of bioleaching, bioflotation and bioflocculation for the beneficiation of low-grade iron ores.IntroductionIncreasing global demand for raw materials has led to diminishing resources of high-grade iron ore. As a result, the mining and utilization of low-grade hematite, limonite, specularite, siderite and goethite ores have attracted more and more attention. However, these types of iron ores are of complex paragenesis and fine disseminated grain size, and often contaminated by phosphorus in the form of solid solution. The distribution of phosphorus throughout the iron mineral crystals prevents the effective use of physical separation techniques, and these complex ores are at present largely untapped due to a lack of cost-effective and efficient processing methods. Chemical leaching and roasting-magnetic separation approaches have been mainly tested only on the laboratory scale and are all either cost prohibitive or ineffective when used on low-grade complex iron ores."

Jan 1, 2015

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Jan 1, 1997

By K G. Harding, E L. Haggard, C M. Sheridan

Mining is a water intensive sector, contributing to declining water resource quality around the world. Improvements to current mine water management practices can help reduce the amount of water utilised by the mining sector and the impact on water resources. Creating a water account can help companies understand water use in their operations and identify areas where water reduction is possible. Water accounting methods include the Water Footprint Network method and the WaterMiner tool.The Water Footprint Network method is used to determine the amount of direct and indirect water used by an organisation either in a process or to manufacture a product. The total water footprint is divided into the blue, green and grey water footprints. Blue water is the amount of water abstracted from surface and ground water resources. Green water is the amount of rain water utilised. Grey water is the amount of freshwater required to assimilate the waste stream to the natural resource and still conform to ambient water quality standards.The WaterMiner tool is a program available via the internet, which can be used to model water use of mineral processing sites. The program reports the amount of raw, worked and treated water used by the process and recommends flows that can be added to reduce the amount of fresh water required by the process.To gain information on mine water management practices in South Africa, a water account for a platinum mine was developed using the Water Footprint Network method and WaterMiner tool. Based on the results, suggestions to reduce the amount of fresh water utilised are made.CITATION:Haggard, E L, Sheridan, C M and Harding, K G, 2013. Water footprint for a South African platinum mine, in Proceedings Water in Mining 2013 , pp 15-20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J. B. Zadra

Much has been published by various investigators on the use of activated carbon for adsorbing precious metals from cyanide solution and pulp. For the benefit of the reader, a list of these earlier publications appears at the end of this report. The present paper deals only with a process for extracting gold from gold-laden carbon and re-use of the de-adsorbed carbon. At the Getchell mine, Redhouse, Nev., experiments have been in progress for several years concerning the use of activated carbon to adsorb gold from their slime circuit pulp. The experimental work has been successful. Their practice has been to ship the gold-laden carbon to a smelter for treatment, which meant the total loss of the carbon in addition to smelter and freight, charges, all of which proved costly and wasteful.

Jan 1, 1950

By Eric Kelley

Having been retained as a legal expert for the fatality at the Canberra, Australia project, it made me aware of how good intended blasters profess to be implosion experts. Owners and contractors can be misled by these representations, seeing a video of Directionalized Structures constructed of reinforced concrete may be impressive to watch, but lack sound evidence of the true mechanics of an actual “implosion”; on steel structures more prevalently. If any well intended blaster comes to a determination that he can implode a structure, it should be not be construed he cannot. It should be well investigated that the specific blaster has verifiable experience. What happened in Australia reflects on all end users of explosives. I have heard a direct quote in our project in Alberta, “We don’t want to have what happened in Canberra”. Such a tragedy could have, and should have been avoided. Simple by using the “Right Tool for the Job”. We should sideline egos and economics. Would any competent blaster compromise his or her reputation, company or insurability? More importantly, have an honest conscience knowing that if the proper explosive is available, use it, don’t shortcut it. If possible expand the schedule. Better, yet, examine all avenues before the project, and last, cancel the project. A human life is our best asset and should not be compromised.

Jan 1, 1999

By George A. Komadina

Pima Mining Company has recently completed their expansion tripling the plant capacity to 18,000 tons per day and now is in the process off expanding to 30,000 tons per day with completion scheduled for the summer of 1967. This paper briefly discusses the additions to the mining department and support areas with a more detailed report on the complete new crushing plant and additions to the concentrator. The crushing plant includes a 54-inch gyratory crusher, three 7-foot standard and seven 7-foot short head crushers along with necessary screens, feeders, and conveyor belts to produce a minus 1/2-inch rod mill feed. The concentrator consists of ten milling sections, each containing one 10-foot by 16-foot rod and two 10.5-foot by 13-foot ball mills, classification is done with cyclones. Pulp from each section is floated in 50 cells of 66-inch Fagergren flotation machines to produce a rougher concentrate which is cleaned in six stages of Denver cleaners to produce a final concentrate The various mill products are thickened with disposal made in conventional manner. Plant instrumentation is discussed in the paper.

Jan 1, 1967

By Charles Vaught

This paper discusses the fact that US coal mining organisations are losing the knowledge they need in order to be able to respond to emergencies. The authors note that knowledge management provides a useful perspective from which to view the problem, but that the debate about what constitutes knowledge should be broadened to include a debate about what constitutes management. It is argued here that knowledge is actually shared knowing distributed across group members; that such knowledge can be managed by cultivating it; and that narrative is the medium through which this may be done. The paper then examines NIOSH research that has attempted to use such an alternative knowledge management approach to help potential mine emergency responders better deal with the predicaments they are likely to encounter on-site.

Jan 1, 2006

By Yongqi Sun, Zuotai Zhang

Hot slags, at the temperatures of 1450-1650 oC, carry a substantial amount of high quality thermal energy, which represents the largest undeveloped energy source in the steel industry. However, the waste heat recovery rate in China is less than 2%; thus there is a great potential of waste heat recovery. In this study, we investigated a chemical method to extract the waste heat from high temperature blast furnace slags, i.e., sludge gasification. Sewage sludge, another substantial waste produced in the municipal system, need to be timely disposed, the organics of which could be gasified using the waste heat in the slags for the purpose of syngas production. Both the kinetics and thermodynamics of the sludge gasification process were clarified here. Most importantly, an integrated system composed of multiple systems such as the steel industry, the cement industry, the municipal system and the chemical engineering industry, was analyzed in this study.

Jan 1, 2016

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By Patrick R. Taylor

Thermal plasma technology has a wide range of applications in extractive and process metallurgy. Beneficiation of complex ores, oxide reduction, melting/remelting of refractory metals and scrap, and the recovery of precious metals from waste products are some examples of potential uses for plasma technology. The highly concentrated enthalpy provided by plasma torches is a cleaner energy source and may give higher processing rates per reactor volume than conventional technologies. Some of the other advantages may be: controlled furnace atmosphere, ability to treat fine feed materials and rapid quenching. A review of some of the uses for plasma processing in non-ferrous process and extractive metallurgy is presented.

Jan 1, 1993

By M Parcell

"Ventilation risks in an underground mine have essentially remained the same for centuries, yet theevidence suggests that there are many coal mines that have failed to adequately control these risks.The conduit for the knowledge learned by previous generations exists in the mining legislation. In an ideal world, mines would not need legislation to tell them what to do; they would resolve the risks to an acceptable level so as to protect the safety of persons in the mines based on the acquired knowledge. There will be some who have been personally aff ected by a mining disaster but for the majority they will be remembered as a vague recollection of an event from long ago. The mining legislation is the repository for the knowledge and outcomes from inquiries of past disasters. The challenge for the current generation, and the generations to come is to appreciate the legislation that exists, so as to not ælearn the hard wayÆ. In reviewing most disasters there is comment or discussion on the adequacy of the legislation, which ultimately results in some amendment to the law. For each person, there is an increasing responsibility to ensure that the same mistakes are not repeated. Understanding the legislation, its history and its purpose is the fi rst step in ensuring thatventilation risks are eff ectively managed. Failing to do this will be disastrous. This paper discussesthe relevance, importance and potential pitfalls of coal mine ventilation regulation."

Jun 1, 2012