Search Documents

By Jorge Cárdenas, Alejandro Luna

In mining simulation for fragmentation results prediction is of utmost importance to study feasibility, ensure safety, and estimate the correct use of resources in drilling an explosive to meet requirements and avoid excessive usage. One critical case is fragmentation prediction, developed through models. Developing a fragmentation model in a mining unit aims to control blasting results to align theoretical and real data and improve correlation. Therefore, it is essential to collect post-blast fragmentation data, organize it, and systematically process it to develop a suitable model that meets variable requirements. Using a robust system of equations, this model should generate the required results with minimal variability between simulation and actual results. Additionally, this model must be adaptive to reduce this variability. Studying the most known and used models in mining resulted in our work correlating Cunningham 2006, Swebrec, and CZM models. Thus, the Simfrag model was created, presenting a robust foundation and combining the most notable advantages of the aforementioned models.

Jan 21, 2025

By C. L. Brown

The frequency of mine fires during recent years, with an apparent increase in recent months, has focused attention on the necessity of reducing this hazard by every means possible. Investigation reports are available on 51 mine fires of electrical origin between August 15, 1949, and August 16, 1954. Nine other fires in the same period were suspected as being of electrical origin. Every mine fire is a potential hazard to underground workmen; it is remarkable that only six lives were lost as a result of these fires, since the injury list was very high. Modern mining methods, with increased power demands and extended distribution systems underground, involve greater electrical hazards and possibilities of costly production delays as a result of inadequate electrical service. Improvements in electric-power-distribution facilities in many underground coal mines is desirable. The purpose of this paper is to show the need for this improvement as revealed by studies and investigations of electric-power-distribution systems representative of those in a large number of coal mines.

Jan 1, 1955

By A J. Kyle

After a brief description of the shaft and surface facilities, this paper describes the planning for the mining operation, the selection of equipment the general method of mining and the sequence of operation. All of the major items of equipment are described, including the components of the power system. The detailed planning is reviewed -from the shaft sinking to the three-shift mining operation. Excavation and equipment changes, as well as long-range planning, are al o di cussed. Introduction THE successful completion of the Yarbo No. 1 shaft of International Minerals & Chemical Corporation (Canada) Limited in July, 1962, added a new type of mine to Canada&apos;s many producing operations. IMC Esterhazy is a unique mining operation in Canada; in fact, it is unique to potash mining in general. Not only is thi&apos;3 a trackless operation utilizing shuttle cars and belt conveyors in its material handling systems, but it excavates all of the ore with continuous boring machine<:;.

Jan 1, 1964

By William Paxton Hewitt

Mineral deposits of western Utah and eastern and central Nevada have produced in excess of $8,500,000,000 since 1871. Through 1965, Bingham Canyon had produced over $4,600,000,000 and seven other camps over $100,000,000 each, principally from base metals. In addition, they yield iron and uranium ores; contain the world's largest beryllium reserves; and have produced the United States' most important gold discovery in 25 years. The area is famous for its silver production and its bonanza-type precious metal deposits, but such production has become unimportant. The area's greatest producers of metallic wealth are base-metal deposits in limestones and porphyry-type copper ores. In contrast to silver's decline, gold production has been rising-the result of by-product operations at Bingham Canyon. The area also contains gold deposits in which the gold is so finely disseminated it is not recoverable by panning. The area's gold ores frequently are associated with realgar, cinnabar, and carbon. The ore deposits generally are attributed to Tertiary intrusives,* but, at Mountain City, they may be related to Paleozoic volcanism. Mountain City has yielded rich chalcocite from quartz-pyrite-chalcopyrite bodies in siliceous sediments. Regional stratigraphy and structure are difficult to interpret, 69 per cent of the area being obscured by alluvium or volcanics. In general, central Nevada consists of chert, shale, silty sandstones, lavas, and pyroclastics; eastern Nevada and western Utah of many alternations of limestone, shale, and sandstone. Central Nevada has been structurally active since late Devonian. Although granitic stocks may have intruded eastern Nevada and western Utah prior to the Cretaceous, these areas remained quite stable until affected by the Laramide Revolution. Precambrian exposures, occupying 3 per cent of the area, have not been important hosts. However, the question is raised as to whether Precambrian carbonates, properly situated with respect to invading mineralizers, might yet prove to be important. This paper describes 16 precious metal camps, 6 limestone replacement districts, 2 silver-base metal vein deposits, and 9 miscellaneous types and discusses briefly the 11 * Some ores, as at Ely, are associated with intrusives of. Cretaceous age. major camps that are described in detail in this Volume.

Jan 1, 1968

By Tommy Wilson

OIL well drilling fluids have become a vital part of the drilling industry during the past 25 years. From chance usage of drilling mud at the fabulous Splindletop field in 1901, drilling fluid control has become an extremely technical and exacting science. Drilling for oil today involves exploration at depths ranging to 21,000 ft, nearly 4 miles. Geological formations encountered at these depths offer a tremendous challenge to the production, research, and service facilities of any drilling mud company.

Jan 5, 1954

By Mahdi Soudkhah, Akhter Hossain

Vertical micropiles are generally considered to be low in lateral resistance. Therefore, battered micropiles are often used when additional lateral load carrying capacity is required. However, battering of micropiles can sometimes be restricted due to existing adjacent structures or utilities, especially in highly urbanized areas. For example, presented in this paper are lateral load test data from a 43-story building project in New York City where vertical micropiles were used due to proximity to adjacent structures. Three static lateral load tests were conducted on micropiles consisting of 13.375-in-outside diameter and 25- to 51-ft-long casings, and socketed 10 to 12.6 ft into the bedrock (gneissic schist). The subsurface profile above the bedrock consists of loose to very dense, mostly sandy and silty soils. The design load for the three test piles was 14,000 lb and the maximum load applied during the tests was 200% of the design load. Lateral load- displacement behavior of the free pile heads from the load tests are compared with the results of p-y analyses based on a widely used p-y method for sandy soils and using a lower and an upper bound estimates of soil index properties and strength parameters. Since the existing p-y curves were formulated for larger diameter driven piles at a specific geographic location, major differences are observed between the results of the load tests and the p-y analyses. In general, the lateral displacements estimated based on the p-y analyses using upper bound soil parameters are relatively closer to the results of the field load testing. Modified p-y curves specific to the sandy and silty soils representative of the general subsurface conditions of New York City matched with the lateral load tests are presented in this paper. INTRODUCTION Micropiles generally are limited in lateral load carrying capacities due to their relatively higher slenderness ratios (ratio of depth to diameter) compared to more conventional deep foundation alternatives, such as driven piles and drilled shafts. So, micropiles are not typically considered as deep foundation solutions when significantly high lateral loads are expected on the substructures. Various means to increase the lateral resistance of micropiles include battering and installing an oversized casing in the top portion of the piles (FHWA 2005; and Richard and Rothbauer 2004). However, it is often not possible to install micropiles in a battered position in highly urbanized areas due to existing adjacent structures or utilities. Installation of oversized casing is often restricted by limited space availability and concerns of losing lateral capacities due to closely spaced group of piles. Thus, estimation of lateral resistance of vertical micropiles can become highly important for geotechnical engineering projects in urban areas when a small to moderate amount of lateral resistances are expected from the substructures, often to withstand seismic and wind loads.

Jan 1, 2019

By G. A. Howes

This is one of a series of circulars dealing with the cost of equipping and developing mining properties in the United States and Canada, prepared and published by the Bureau of Mines in cooperation with various mining and exploration companies. This group of circulars is designed to supplement an earlier series which covered the methods and costs of mining and milling at a large number of producing properties. ACKNOWLEDGMENTS The authors desire to thank Robert A. Bryce, president of Macassa Mines (Ltd.), for permission to use the data presented in this paper, and to acknowledge the cooperation of A. J. Keast, under whose direction as manager the plant was installed and equipped and the shaft was sunk to a depth of approximately 2,000 feet.

Jan 1, 1932

By Mike Fontaine

The success of a project is defined by meeting the financial performance objectives of the business case within a stipulated timeframe. Early in design, little information is normally available; the uncertainty introduces risk to the project outcome. Using a range of risk management tools and techniques, a project can be developed from front end loading phases 1 through 3 (FEL1–FEL3), and project implementation (FEL4) and then into operations with an optimized probability of success. For every project element, the risk management framework embodies: establishing a context; assessing risk (identify, analyze, and evaluate); and treating risk. Embedded within design activities, this process mitigates or eliminates risks. Monitoring and control, as well as extensive communication and consultation with stakeholders, is integral to the risk management process.

Jan 1, 2015

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the fifth of a series of reports giving the results of studies by countless under part (1) of the investigation. (See appendix.) This report covers Westmoreland County, Pa., which comprises parts of New Kensington, Freeport, Elders Ridge, Pittsburgh, Greensburg, Latrobe, New Florence, Johnstown, Brownsville, Connellsville, Donegal, and Somerset quadrangles. (See fig. 1.) A short resume" of the chemical and carbonizing properties of the coals are included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By Don M. Coulter

"INTRODUCTION The district comprising Union, Lafayette, Pontotoc and Calhoun Counties, Miss. (fig. 1), was examined in October 1941 by R. W. Smith of the Bureau of Mines, accompanied by J. W. Adams of the Mississippi Bauxite Co. 3/ Subsequently, geologists of the Federal Geological Survey made a more detailed study of the area. 4/Bauxite had been reported as present in several localities in Pontot. County, and large deposits of kaolin are known in Pontotoc, Union, Calhoun, and Lafayette Counties. Many of the bauxite deposits, such as those on Big Hill, Second Hill, and Third Hill, in Pontotoc County, form the caps on hills and are outliers of Wilcox deposits on the Midway formation. Such deposits could have no extensions because of erosion and were not examined, as they were investigated by the Mississippi Geological Survey. 5/ Most of the bauxite was known to be low-grade, with a high iron content. However, Pontotoc County in particular presented possibilities of finding high-grade bauxite with a low iron content by drilling down the dip from the Wilcox-Midway contact. Consequently, with few exceptions the investigation was confined to drilling in this direction.Headquarters were established in Tupelo, Miss., on July 13, 1943, and mineral agreements were obtained covering 8,367 acres of land, with 62 land-owners in Pontotoc and Union Counties. Holes were drilled on properties of three of the landowners in Union County and 36 in Pontotoc County."

Apr 1, 1948

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on any standard PC.

Jan 1, 1997

By P. F. McIntyre

Electrolytic refining of lead was first carried out on a commercial scale at Trail, B. C., in 1903. The capacity at that time was small, and cell-changing operations were managed with chain block and monorail. Development up to 1922, utilizing crane installations and cell additions, attained a production of 100 tons per day. Successive additions from 1922 to 1926 further increased the rated capacity to 396 tons per day. Other improvements in metallurgical practice have gradually increased production, until for the year 1935 it was 448 tons per day. During the first five months of 1936, an average daily production of 504 tons was maintained without increasing the size of the plant. Lead Refinery Buildings.—The tank room and the lead-melting and casting equipment are housed in two buildings, which parallel each other and which for the greater part of their lengths are joined by a connecting aisle. All basements, walls, sumps and floors are of concrete. Where exposed to the electrolyte, the concrete has a protective coating of asphalt (220" melting point) over a coat of asphalt paint as a primer. Buildings erected before 1924 are of wood. More recent additions are made of structural steel with gunite siding. A brick building, adjoining the older section of the tank room, houses the slimes-treatment plant. The power house, containing motor generators, air compressors and rectifiers, is constructed of tile. Cell Construction.—The electrolytic cells are of reinforced concrete lined with asphalt. They are cast in pairs, the outside dimensions of a double cell being 113 in. long by 73 in. wide by 48 in. deep. The bottom is 6 in. thick and the sides, ends and center wall are 4 in. thick. A ledge 3 in. wide and 2½ in. deep is left along the top of the side walls to carry the insulators and bus bars. Reinforcing consists of ½-in. round iron rods. Cell inspection and repair work is done in conjunction with the cell-changing operations. The repair work necessary is usually confined to renewing chipped asphalt, unless a tank has been accidentally broken. Minor concrete repairs can be easily made in place. The broken concrete

Jan 1, 1937

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By J. C. Gibson, C. H. Stockwell

"The San Antonio gold mine is at Bissett, Manitoba, on the north shore of Rice lake, 100 miles northeast of Winnipeg. Gold was discovered on the property in 1911, but intensive exploration was not undertaken until 1926. Milling commenced on May 1st, 1932. Total amount of ore milled from that time until the end of 1946 was 1,766,670 tons, having a value of $18,378,317.GENERAL GEOLOGYThe rocks in the vicinity of the mine are Precambrian and include three groups, namely, the Rice Lake series of volcanic and sedimentary rocks, basic and acidic intrusions, and a younger formation of sediments known as the San Antonio formation (Fig. 1). The lower part of the Rice Lake series, consisting of flows of rhyolite, trachyte, and andesite with interstratified beds of agglomerate, occupies an area extending southward from Rice lake. The lake itself and the country to both east and west of its northern end is underlain by the next succeeding beds of the series, which are chiefly tuffs, arkose, and conglomerate, but include a thin band of basalt. Northward from the lake, these are succeeded by the upper beds of the series, first a thin band of basalt and, overlying this, porphyritic andesite flows interlayered with beds of volcanic breccia or agglomerate.The Rice Lake series has been invaded on the east side of the lake by a body of basic rock ranging in composition from gabbro to diorite and quartz diorite, now much altered. This is cut by younger sills and dykes of basic rock, probably diabase, the original texture of which is largely destroyed by alteration. Numerous dykes of feldspar porphyry, quartzfeldspar porphyry, and a few of a rhyolite-like rock, occur south of the lake, but are uncommon to the north. They cut the diabase and older rocks.Extending westward from Rice lake and lying with marked angular unconformity against all of these rocks is the San Antonio formation, consisting of cross-bedded, arkosic quartzite."

Jan 1, 1954

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015

By Manuel Gomez

Published experimental coke data from a pilot plant slot-type oven were examined by statistical regression analysis. Quantitative relationships were found to exist between the coking rate, bulk density, and fine grinding of the coal, sole-oven expansion, volatile matter, moisture, ash, and carbon con-tent of the coal and coke parameters indicative of size and strength. Regression equations developed from coke data were shown to yield computed values that were in good agreement with experimental results for 11 coke properties. Prediction equations developed were evaluated with an independent set of data. Present results indicate that the variables cited undergo much interaction and the sum of these interactions determines coke size and strength.

Jan 1, 1967

By Anupam Madhukar

The essence of an atomistic unified kinetic model of strained thin film growth and defect initiation is presented along with a comparison of its consequences obtained from computer simulations with experiments. Within the competing kinetics of a strain dependent activated incorporation of atoms and an asymmetry between upwards and downwards inter-layer migration, the model provides a consistent description of 2D versus 3D morphology evolution accompanied by the appearance of surface vacancies and steps at no energy cost. The correlated migration of these precursor defects offers an atomistic mechanism for the emergence of surface half-loops from the growth front (thus accounting for configurational and thermal entropy) governed by activation energies closer to their correlated motion under the evolving strain fields and thus substantially less than those calculated with respect to the perfect crystal as the reference state. The essential mechano-chemical nature of the problem is compared and contrasted with the historical literature of such phenomenon as precipitation hardening and sintering in metallic and ceramic composites.

Jan 1, 1994

By W. A. Young

Bull Lake is one of several saline lakes situated a few miles north of Rawlins, Carbon County, Wyo. (figs. and 2).. The Bureau of Mines conducted preliminary investigations of sodium sulfate deposits in many of the lakes and performed detailed work on Bull Lake. This investigation consisted of drilling 11 vertical holes through salt beds using diamond core bits and Iwan-type auger bits. Bull Lake lies in a shallow, closed depression in loosely consolidated sand. The salt beds, ranging in thickness from 2.5 to 26 feet, occur above a thick bed of shale of upper Cretaceous age. The salts appear to have been deposited in the lake from surface and subsurface drainage. The source of salt is undoubtedly the enclosing sedimentary rock&apos;s exposed to the west of the basin. Sodium sulfate in the deposits probably is present as mirabilite or Glauber salt (Na2SO4-10H2O). Chief impurities in the deposits arc mud and sand. Other soluble salts present average approximately 1 percent combined. Cores from the 11 holes were analyzed in the Bureau of Mines laboratories at Salt Lake City. Drilling totaled 512 feet. Results of analyses are given in the appendix.

Jan 1, 1951

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By Ernest W. Johnson, F. E. Cash

"INTRODUCTION Mine operators have long realized the importance of providing a satisfactory and dependable means of giving prompt warning to underground mine workers at the occurrence of a mine fire or other threatened disaster.Most underground mines of the Lake Superior district are prepared to inject a stench liquid into the compressed-air system quickly to give such warning. The liquid evaporates quickly and gives off an intense and easily recognizable odor even when present in minute quantities in the mine air. Workers in the mines studied have been fairly generally familiarized with the odor and instructed as to evacuation procedure when the warning odor is detected.In some mines provided throughout with electric lighting, including working faces, a prearranged light-flashing signal is given as a warning supplementary to that received from the stench.In a few mines, workers have been instructed to evacuate the mine immediately in the event the compressed-air supply is cut off, regardless of whether mechanical failure may be involved.Information obtained in observing a number of stench-injection tests is compiled and presented in the hope-that it will serve as an incentive to provide means of making stench injections at mines not now so equipped and for making similar tests at other underground mines, so that in case unsatisfactory results are obtained rectifying adjustments or changes may be made in time. It is further hoped that this paper will bring out the real importance of repeating these tests from time to time, at least once a year on each operating shift, so that in the event of an actual emergency, underground employees will receive a prompt warning."

Nov 1, 1945