Search Documents

By F. S. Boericke

"INTRODUCTION The mineral found in natural-chromite deposits is never pure Fe0.Cr203, but rather one in which the Fe0 and Cr203 are in part replaced by Mg0 and A1203, respectively. The purest gravity concentrates from many domestic de¬posits consist of a mineral referred to as ""picotite,"" in which this isomorphous replacement is such that the ratio of chromium to iron is low. The Bureau of Nines has investigated methods of chemically beneficiating ores that contain too much iron to be classed as ""high-grade"" chromite 3/ Early investigations 4/ demonstrated that high-iron chromite or picotite ores can be roasted with carbon to obtain selective reduction of the contained iron, and that most of this reduced iron can be removed by acid-leaching the roast products to produce residues of higher chromium-to-iron ratios. tests 5/ indicated that commercially acceptable reaction rates cannot be obtained at roasting temperatures below 1,3000 C., using solid carbon as reducing agent. By this high-temperature reduction and subse¬quent acid-leaching, however, all ores investigated, regardless of the original composition, readily yielded residues considerably better than the minimum specifications for high-grade chromite.In an effort to obtain satisfactory reduction of chromite at lower temperatures, liquid and gaseous seducing agents were tested with varying success. Of the several reducing agents used, methane appeared to be the most promising and was shown to be highly effective at temperatures between 1,000º and 1,100º C., roughly 300º below the roasting temperatures necessary in solid carbon reduction. Further experiments indicated that mixtures of methate with some diluent (hydrogen or other nonoxidizing gas) gave better reduction than did methane alone."

Feb 1, 1946

By Kenneth E. Gray

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton's equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?' lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.' It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By S Serp, M Duchateau, P Chevreux

Molten salt reactor (MSR) is a promising advanced reactor system aiming to the transmutation of minor actinides such as americium in order to reduce the inventory of ultimate nuclear waste. The fuel is a molten salt in which actinides are homogeneously dissolved in the liquid phase. A chloride salt may be retained for this concept, as it provides low melting point, high solubility of actinides, harder neutron spectrum. To avoid corrosion and precipitation issues, molten salt composition has to be carefully controlled with impurity content as low as possible. Obtaining pure actinide chlorides without contaminants such as oxide, oxychloride, hydroxide and water is still a challenge. To prepare actinide-bearing salt, the chlorination of actinides oxides was investigated in an unstirred reactor under flowing gas as solid-gas reaction. The carbochlorination of PuO2 were performed in the temperature range of 600 to 800°C with chlorine gas as a chlorinating agent and the presence of solid carbon. PuCl3 was successfully synthesised by this method and characterised by X-ray diffraction measurements but some impurities such as oxide phase remain inside the formed product. Refinements of anhydrous and hydrated PuCl3 phases by Le Bail method were also performed for crystalline materials definition. Conversion mainly depends on the chlorinating temperature and the contact between the oxide and the chlorinating agent. A conversion value of 70–80 per cent was achieved at 700°C from PuO2 with quite high specific surface area. The conversion rate was not improved with increasing the chlorination time. The volatilisation of Pu was observed during the carbochlorination experiments. To avoid a loss of Pu caused by sublimation, the chlorination temperature should be limited to 650°C despite that the conversion of PuO2 to PuCl3 was enhanced by increasing temperature. Both carbochlorination and hydrochlorination of AmO2 were also carried out leading to the formation of AmCl3. These first results suggest that americium oxide was chlorinated more readily than plutonium oxide. The purity of produced PuCl3 and AmCl3 still deserves further investigations.

Jun 19, 2024

By E. P. Palmatier

RECENTLY a cooling system has been in process of installation on the 3400 and 3600-ft. levels of the Magma copper mine at Superior, Ariz. The general system of ventilation employed at this inclined-vein mine is as follows: Ventilating air enters the shafts on the western side of the mine. Booster fans at each level each deliver approximately 38,000 cu. ft. per 'min. to the drifts. This air passes diagonally upward to the upper levels of the mine on the eastern side, where it passes up the shafts to large exhaust fans on the surface. Owing to the dip of the vein, all operations on the eastern side of the mine are above the 2500-ft. level, and those on the western side below the 2500-ft. level. At present, 2500 lineal feet of new drifts are being driven-on each of the 3400 and 3600 levels. The rock temperature is about 135°F. Until the new installation is completed, ventilating air for the two levels is supplied through Flexoid tubing from small booster fans -on the 3200-ft. level. The air picked up by these booster fans has a dry-bulb temperature of approximately 85°F. and a wet-bulb temperature of 82°F. By the time this air reaches the end of the Flexoid tubing at the 3600-ft. level, the dry-bulb rises to 101°F. and the wet-bulb to 86°F. The conditions at the head of the new drift were 102' dry-bulb and 93' wet-bulb.

Jan 1, 1937

By John J. Henn

Ten proposed processes for the recovery of manganese from domestic resources as a high-grade oxide product are described. Nine of the processes employ sulfur dioxide, sulfuric acid, or a combination of both for leaching. The tenth process utilizes sulfur dioxide to sulfatize the ore at 600° to 850°C before water leaching. In addiction to these ten complete processes, six processes from the patent literature are described. Methods for receovering MnSO4?H2O are also reviewed.

Jan 1, 1968

By A L. Welsh, P S. Newling

Mill operators are entrusted to manage what are normally the largest capital assets on any mine site. Achieving maximum utilisation and lowest costs that drive operating margins are realised by applying well known fundamentals of good housekeeping and proactive (as opposed to reactive) maintenance programmes. Historically, maintenance and operations staff are bought in late during the construction stage and often do not have the time, know how or tools to put in place (let alone train the incumbent staff) a functioning maintenance system before commissioning starts. They then get drawn into a reactive maintenance paradigm as teething problems post commissioning are dealt with and day to day issues envelop the line tradesmen and supervisors. Additionally, even when some semblance of a planned maintenance system is established, it is often the case that over time personnel and cultural issues mask the development of problematic maintenance practices. As has been observed by the authors on many occasions, even when some basic programmed maintenance system is in place, the collection of maintenance data is often inaccurate, incomplete and not subject to analysis. The net result is of course a high incidence of machine failure leading to lower than expected availability, which ultimately translates to lower revenue and higher net maintenance costs. The time taken and the cost to repair a failed machine is always greater than the timely and planned repair of a worn machine.Upon review of a number of processing plants around the world, especially gold and small base metal operations, it is apparent that companies need to implement maintenance systems whereby the operators are not overwhelmed with data and can manage by exception. Inadequate or inaccurate data collection and analysis result in poor decisions being made and misguided actions taken. GR Engineering Services (GRES) has developed a system to enable the custodians of mining plant assets to make more effective and effective use of maintenance data by being able to focus on the indicators of plant deterioration and to programme concurrent maintenance activities to maximise plant availability and utilisation.This paper outlines the structures that can be employed to address the challenges of implementing a proactive asset management system. The best practice strategies described herein have been based on the fundamentals of a sound asset management framework:a phased approach to the development of Asset Management methodology and processeseffective implementation of programmed maintenance routinesmanaging asset condition data collected from various sourcesefficient analysis of asset data and management by exceptioninterfacing asset management data with Computerised Maintenance Management System (CMMS) and Electronic Management Systems (EMS) systemstips to assist with maximising asset performance.CITATION:Welsh, A L and Newling, P S, 2015. Operating strategies for custodians of company assets creating wealth, in Proceedings MetPlant 2015, pp 338–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Christian Divis

[ ]

Jan 1, 2002

By T. J. White

A synthetic Mineral Immobilization Technology (SMITE) has been developed for stabilizing municipal and hazardous waste incinerator ash. Tailored additives are introduced to the ash in a' first stage that pre-stabilizes all the toxic metal components in non-volatile forms. and in a second pyrometallurgical stage, these are converted to insoluble mineral analogues. It has been found that a combination of apatitie. spinal, anhydrite and monazite can immobilize all the ash components at high waste loading and high density. Typically the stabilized products contain in excess of 50 wt% ash and have densities of 2.5- 3.0 g.cc-1. Toxicity Characteristic Leach Procedure (TCLP) testing has demonstrated that the products well satisfy regulatory requirements. The cost of production and disposal of SMITE waste forms in 2-5 less expensive than. convential methods of solidification/stabilization. This paper will describe the principles of SMITE design for ash stabilization, outline the fabrication procedure, and present comprehensive microstructural and chemical data to validate waste form performance.

Jan 1, 1996

By E. G. Galvez, E. Mate, L. A. Cisternas, C. Cruz, L. Cortés, M. E. Osorio

Designing and optimising flotation circuits are critical for mineral beneficiation plants, and therefore several procedures have been published. The modelling of flotation circuits with the objective of design and optimisation is problematic in that different approaches are used for the modelling of flotation units and regrinding units. Usually, regrinding models are based on particles characterised by their size, while flotation models are based on species characterised by fast and slow classes. The relationship between particle size and liberation can be used, but it requires laboratory studies that are time-consuming and costs are high. It is therefore not surprising that few studies on flotation circuit design and optimisation include flotation units and regrinding units simultaneously. In this paper, it is proposed to model the regrinding stage using species characterised by fine-slow, medium-fast, and coarse-slow flotation species. In deep, the regrinding model is derived from a population balance approach based on flotation species. The fraction of these species at the feed and product of the grinding unit is determined by flotation tests. Then, based on these data, the model parameters can be determined by a regression estimation procedure. A local ore was used to validate the model. Keywords: Modelling, flotation circuit, grinding circuit, process design

Jan 1, 2020

By Z. Smieszek, W. D?browicz, J. Pawlowski, G. Krawiec, J. Czernecki, J. Por?mbski, S. Gizicki

Rapid development of the automotive industry and motorization has been observed in Poland over the last decade. This phenomenon has increased the amount of used car batteries requiring recycling and has thus posed new challenges for their processing. Orzel Bialy" S.A, is the major secondary lead smelter in Poland. Ibis paper describes the program for smelting technology modernisation and productivity increase through the application of oxy-fuel burners, which has been implemented at "Orzel Bialy'' S.A. The main objective of smelter modernisation, which was to increase the furnace productivity by 20%, has been achieved. This paper outlines the previous and present state of the lead acid battery scrap smelting technology at the "Orzel Bialy" S.A. Specifications of the burners and of oxygen installation are given. Industrial tests with the modernised smelting technology and optimisation of the process parameters are described, and the results obtained are discussed.

Jan 1, 2000

By E. Matinde

Human beings have been dependent on metals and alloys for livelihoods since time immemorial. In fact, there is irrefutable evidence that successful ancient civilizations achieved supremacy over their environments through the mastery of metals and alloys (Miller, 1995; Mtetwa, 2022). Over time, metals and alloys have evolved to become ubiquitous engineering materials indispensable to mankind, with applications in industrial and residential infrastructure, agriculture, energy generation and storage, transportation and communication systems, and manufacturing, among others (Elshkaki et al., 2018; Watari et al., 2021). Population growth, technological developments, and increase in urbanization and industrialization are all intricately linked to the intensity of use of metals and alloys. With up to 5 billion people estimated to live in urban areas by 2030 (Armstrong, 2009), the demand for metals and alloys will inevitably increase in order to satisfy the increased demand for infrastructure, machinery, and other human needs (Elshkaki et al., 2018; Watari et al., 2021). According to LePan (2022), urbanization and growth of mega-cities will increase the demand for metals and alloys, such as nickel, steel, aluminium, and copper by 116%, 50%, 57%, and 26%, respectively, between 2019 and 2035. Naturally, the production of metals and alloys from natural ores, secondary resources, and/or a combination of both, to meet this increased demand will invariably lead to the increase in generation of deleterious emissions in the form of wastes. In fact, mining and metallurgical wastes currently constitute the world’s largest anthropogenic streams by mass, often containing a high concentration of elements and compounds that can cause potential damage to natural ecosystems and humans (Hudson-Edwards et al., 2011; Lottermoser, 2011; Matinde et al., 2018; Seetharaman et al., 2022). Obviously, society’s heavy reliance on new mineral resources to drive the emerging energy transition entails that the legacy of these waste streams will continue unabated for the near-foreseeable future. The scarcity of high-grade mineral reserves, coupled with deliberate efforts to solve the anthropogenic circularity conundrum, therefore introduces a high level of urgency in the metal extraction industry to develop nascent and more eco-friendly processes and technologies. Integrating circular economy principles based on intentional configurations of circular industrial ecosystems in order to maintain the value of materials and resources in the economy for as long as possible is widely accepted as a practical approach to mitigating the negative externalities imposed by

Sep 1, 2024

By H. G. Oltmann

The equilibrium nitrogen solubility in the CaO-SiO2system was studied by a slag-gas equilibration technique, in graphite crucibles at 1823K under a CO-N2 atmosphere. The nitrogen content of the slags was determined by the Kjeldahl method. A reliable technique was used to obtain an initial nitrogen content in the master slags, from the addition and pre-melting of silicon nitride. Reduction of silica by graphite was found to occur during the equilibration experiments, resulting in compositional changes of the slags. The results were extrapolated to equilibrium by kinetic evaluation of the data. The nitrogen solubility showed good agreement with the result of Suito and Sano, while Fruehan?s results were lower. However, the results of the present study do not support the maximum nitrogen solubility values found by Sano.

Jan 1, 1999

By Leticia Costa Macêdo

Esse trabalho tem como objetivo analisar por meio da termodinâmica computacional a influência do K2O na dissolução das fases sólidas formadas durante o processo de dessulfuração de ferro gusa. Para isso, foi utilizada a cal como agente dessulfurante e a Sodalita (Fonólio) como fundente, realizando uma adição de K2O no fluxante de 1% a 10%, com uma temperatura de trabalho de 1400ºC. Por meio do uso de software de termodinâmica computacional FactSage, foi possível simular e avaliar as fases sólidas e líquidas formadas na temperatura determinada e comparar com os resultados obtidos com outras análises. Os resultados obtidos mostraram que o aumento gradativo de K2O levam a um aumento do potencial termodinâmico de dessulfuração e melhores condições cinéticas, sendo a mistura que apresentou os melhores resultados a que continha 10% de sodalita com adição de 10% de K2O na fonte.

Oct 30, 2017

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By M Barker, H Li

The total number of tailings accidents has reduced from over 50/decade in the 1960s-1980s to less than 30/decade in the 2000s to 2010s. However, the rate of significant tailings dam failures has not been reduced. The significant tailings dam failures the mining industry experienced in the recent history include: Merriespruit, South Africa, 1994; Los Frails, Spain, 1998; Kolontár, Hungry, 2010; Mount Polley, Canada, 2014; and Samarco, Brazil, 2015. The conventional Factor of Safety approach itself may not be enough to further reduce the rate of significant tailings failures due to its limitations such as uncertainty. For example, the same factor of safety could have a vast range of annual probability of failure for different tailings dams, and insufficient consideration of failure consequence. This paper presents a risk based approach for design with the objective being to minimise tailings dam failures, especially those significant tailings failures with high consequence and low probability. This approach includes risk based design and risk management using bowtie tools. In the risk based design, quantitative analysis will be used to estimate the annual probability of failure and the tolerable failure criteria is linked to the consequence category. Bowtie analyses will be used to understand hazards and risks and identify and select independent controls that are effective in preventing and mitigating catastrophic failures. In this paper, examples of risk based design and bowtie analyses are presented and discussed. CITATION:Li, H and Barker, M, 2018. Risk-based approach for minimising tailings dam failures, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 397–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Mark F. Sindelar, Yi Luo, Hua Jiang, Michael T. Shook

"Convergence of roof and floor in underground mine openings is a common occurrence. This convergence not only adversely affects the ability of workers, equipment and supplies to travel through the mine, it also reduces the effectiveness of the mine ventilation system, which is essential for the dilution of methane gas and airborne respirable dust. While installing secondary standing supports to control floor and roof convergence, such supports, by nature, partially obstruct a portion of the airway. These added obstructions inhibit the ability of the ventilation system to operate as efficiently as it could by increasing the resistance in and reducing the cross-sectional area of the airway.This study introduces and demonstrates the benefits of The Eye CAN™ standing roof support, which controls floor and roof convergence and is less obstructive to air flow than conventional wooden cribs. Laboratory findings show that the normal resistance of a supported lined airway is reduced by using this new product from Burrell Mining Products, Inc., while providing the same roof support characteristics of an established product-The CAN®. Load vs. displacement curves generated from laboratory tests demonstrated that this new product behaves with the same roof support characteristics as others in The CAN product family. Ventilation data gathered from a simulated mine entry was then used for computational fluid dynamics (CFD) modeling. The CFD analysis showed an improvement with The Eye CAN versus other accepted forms of standing roof support.This proof-of-concept study suggests that, when using this new product made by Burrell Mining Products, Inc., not only will the convergence from the roof and floor be controlled, but airway resistance will also be reduced.INTRODUCTIONOne of the basic elements of underground mining is the necessity to support the mine roof. It is well-known that easier reserves have been mined so that today's underground mines present challenging conditions. Factors influencing roof support decisions include mine depth, mining method, overburden composition, and agency regulations. Mining engineers, therefore, have to balance three objectives: safety, engineering, and cost. While safety is obviously paramount, and engineering often complements safety, the cost effectiveness of any product, method, or device warrants additional consideration in today's harsh business climate. Avenues for adaptation and improvement are found at the intersection of the three objectives."

Jan 1, 2016

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heating at 200°C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. Materials and Methods The work was done on high grade electrolytic copper, 99.942 per cent. copper plus silver, silver 0.0008 per cent. It was hot-rolled to >/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire 'were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

By Albert H. Clough

The West Lynn Canal subarea of the Juneau Mining District (JMD) is defined by Lynn Canal on the east, Davidson Glacier to the north, Icy Strait to the south and the Glacier Bay National Park Boundary to the west (figs. C-l and C-2). This area extends along the main-land west of Juneau (across Lynn Canal) northerly, to approximately 20 miles south of the city of Haines. The only roads in the area are relatively new logging roads at the southern end constructed to support a U.S. Forest Service timber sale. There is also local road access near the community of Excursion Inlet. Access to the remainder of the region is either by boat, aircraft, or 'foot. Helicopters provide the only time effective access to all but the coastal parts of the West Lynn Canal subarea. Coastal areas may be reached by small boat or float aircraft. There is an unimproved dirt airstrip just north of the mouth of the Endicott River. This airstrip is suitable for use by light aircraft. The subarea lies within the Tongass National Forest and is managed by the Department of Agriculture, U.S. Forest Service. Approximately two-thirds of the forest lands are open to mineral entry under the current Tongass Land Management plan. The remaining forest lands comprise the Endicott River Wilderness area, which is closed to mineral entry. Private lands within the study area are sparse, with scattered homestead tracts along the coastal regions and in the Excursion Inlet area. Sealaska (Southeast Alaska Regional Native Corporation) also has land selections in the southern Chilkat Range. Tidal and submerged lands are owned by the State of Alaska.

Jan 1, 2012

By D. R. Pyke, R. S. Middleton

"Three main types of base metal sulphide mineralization are present in the Timmins area:(1) -Massive and stringer-type copper-zinc deposits occurring mainly in pyroclastic rocks, as typified by the mines of Kam-Kotia, Jameland and Canadian Jamieson, or within or close to possible breccia pipes as shown by the Genex and Kidd Creek mines. With the exception of the Kidd Creek mine, all of these orebodies occur northwest of Timmins (Kamiskotia area) and appear to lie within or close to a major center of volcanic activity characterized by a thick accumulation of felsic pyroclastic rocks and subordinate epizonal intrusions. The margins of the rhyolitic pile are interfingered with mafic volcanics; overlying sedi-ments mark the termination of a vol-canic cycle. The copper-zinc deposits in the Kamiskotia area are confined to a particular stratigraphic unit. Ore-bearing solutions were probably derived from the intrusive complex of the volcanic pile.(2) -Porphyry copper deposit of the Mcintyre mine. The deposit occurs in a quarz porphyry intrusion related to the volcanism in the area (Hurst, 1936). Mineralization was probably introduced at the time of intrusion, and subsequently redistributed within the porphyry during deformation. (3) -Massive and disseminated nickel mineralization, associated with serpentinized alpine-type ultramafic intrusions, as shown by the Alexo, McWatters, Hart, Inco and Texmont deposits. The nickel mineralization occurs at or near contacts of the serpentinites with felsic or mafic volcanics, or sulphide-bearing iron formations. The nickel deposits south of Timmins are confined to a particular stratigraphic unit along the margins of domical-shaped structures which appear to outline former volcanic centers. Sulphurization as pro-posed by Naldrett (1966) appears to be a workable hypothesis for the formation of some of the deposits."

Jan 1, 1971