Search Documents

By Y Lin, B J. Seligmann, M Hassall, S Micklethwaite

For multi-site mining companies, checking the quality and consistency of the data recorded in risk registers is important for confirming how well mine safety management systems have been implemented. However, this task is complicated by the differences in scope of the site, their particular nature, the complexity of the operations and many other factors that can introduce nuances to the characteristics of the risk registers. We present here an application of a technique called Causal Network Topology Analysis for comparing the quality and consistency of risk registers. By quality we refer to, for example: - missing causal relationships between risks - location of missing controls - focus of risk treatment strategies: prevention versus mitigation controls. By consistency we refer to how causally interdependent are the risk events. There are often causal interactions between the lines of a risk register that mean that the likelihood and consequence scores that are applied to each risk event are not independent. We measure this degree of interactions by: - proportion of independent scenarios per register - efficiency of risk treatment strategy comparison. This approach can indicate quality and consistency differences between registers irrespective of the actual details of the site or operation. This occurs by comparing aspects of the structure of a causal network extracted from how the risk events, causes, controls and consequences causally interact. In this work we compare pairs of registers to demonstrate the approach.

Apr 16, 2024

By Lu Yang

In the last two decades, acid iron ore pellets have established their predominant position as the iron-bearing burden material for blast furnace ironmaking in North America. It is a general practice that pelletization plants are asked to produce pellets of certain chemical composition and in a narrow range of sizes. A minimum amount of fines created during handling and transportation is desirable. Such a requirement is often expressed indirectly by the minimum compression load causing a pellet to break. The behavior of pellets inside a blast furnace, of course, is very important for a smooth and efficient operation. Before its melting in the lower part of a blast furnace during this period of several hours the behavior of pellets depends on their properties after induration as well as conditions inside each furnace. Among properties of indurated pellets, the ability to maintain their physical integrity in the burden and to be reducible are most important. To maintain the integrity of pellets (i.e., minimal low temperature breakdown, swelling and softening) so that there will be adequate overall permeability for certain wind rate and local permeability for gas/solid contact for reduction. A higher reducibility will moderate the adverse effects of swelling and softening and contribute to a smooth operation and efficient use of heat and reductants in a blast furnace. An article devoted to the relationships between the quality of iron ore pellets and blast furnace practice has been published elsewhere(1); therefore, no further discussion is needed here. The mechanism of strengthening of iron ore pellets during firing has been the subject of investigation of many authors(2). There is no doubt that the bridging of the growing hematite grains, particularly starting with magnetite concentrates, is very significant in the production of strong pellets. Recently, there are many reports from blast furnace operators that they have noticed the adverse effect of LTB in their plants. It is obvious that the strength derived from bridged hematite grains may disappear when hematite is converted to magnetite with thorough breakdown of grain structures. It is suggested that some other strengthening mechanism may be required in order to improve the LTB index of acid pellets. The influence of porosity on both compression strength and reducibility follows regular patterns. It has been suggested(1) that the amount of liquid slag in pellets during firing determines to a large extent the porosity, hence, indirectly, strength and reducibility.

Jan 1, 1983

By David E. Van Dillen

The computer program described in this user's guide provides for the static, three-dimensional, linear and nonlinear analysis of structural and geological systems by the finite element method. The guide describes the capabilities and general features of the program and shows how input is prepared. A number of recent advances in finite element theory and computer technology are incorporated in the program. Nonlinear material properties are provided for, including isotropic, anisotropic, and time-dependent material properties, gravity loading, simulation of a sequence of excavation or construction, and a slip or joint element. The finite elements include beam, rod, axisymmetric and plane quadrilateral, hexahedron, thick shell, axisymmetric and plane joint, and a three-dimensional joint. The program also has an automatic mesh generator to minimize user input preparation for continuum finite element meshes.

Jan 1, 1981

By M. T. Smith

In a 2,000 square mile area of Polk, Hillsborough, Hardee and Manatee Counties in Central Florida is located one of the richest known deposits of the life-giving mineral, phosphorus. Under layers of sand and clay are found millions of tons of phosphate rock, best source of this element which is necessary to all forms of life - plant, animal and human. Phosphorus is an irreplaceable ingredient in all complete plant foods, and more than 90% of Florida's vast production goes to enrich the croplands of the United States and many other areas of a hungry world. In addition to this, it has wide industrial use in the manufacture of many products - detergents, baking powder, carbonated beverages, steel, matches, munitions, glass, insecticides, dyes, water softeners and innumerable others. Not only does phosphorus make life possible for us - it also helps us to live longer and better.

Jan 1, 1962

By Manuel Gomez

Carbon number distributions were obtained for tar acid fractions from five low-temperature tars by low-ionizing voltage mass spectrometry. Quantitative data for phenols representing seven structural compound types were examined by statistical analysis. It was shown that for the phenols discussed, the data could be represented by regression equations expressing phenolic concentration as a function of the reciprocal of the carbon number and the carbon-to-hydrogen ratio of the parent coal. The total concentration of each structural type present was found to depend on the molecular weight and boiling point of the initial member of the group. Carbon distribution data for the tar acid fractions studied support the view that low-temperature tars contain the same chemical compounds but in different proportions.

Jan 1, 1965

By X. Wu

Tunnel Boring Machines (TBMs) are widely used for tunneling in urban areas because of their high advance rate, precise as-built profile and minimal impact to buildings and traffic on the ground. For a tunnel built by a TBM, there are strict requirements on alignment control and safety. To meet these requirements, it is important to monitor the position of the TBM. In the current practice, the TBM position data, including advance distance and line and level deviations, are reported manually to the managers on a daily basis. To interpret and analyze the position data, the managers also need to refer to various construction drawings. This practice is untimely, inefficient, and error prone for decision making. To improve the current practice, an automatic approach for real-time as-built tunnel product modeling and visualization is proposed, based on TBM position and orientation data autonomously sourced from the Virtual Laser Target Board (VLTB) TBM Guidance System developed at University of Alberta. Related information of the tunnel project, such as the as-designed alignment, soil layers, the ground, existing utility lines, is also visualized together with the model of the as-built tunnel. The modeling algorithm is presented step by step. Its application in a real-life drainage tunnel project is discussed and limitations are also identified.

Aug 1, 2013

By D. T. Couillard

Video technology is becoming an important tool for many designers of industrial training programs. This report describes how trainers at the Minntac Mine, Mt. Iron, MN, have developed videocassettes of safe job procedures (SJP's) for training miners assigned to perform unfamiliar work tasks. All steps necessary for videocassette production, from idea to finished product, as well as the required equipment and prices, are listed and/or briefly explained. Minntac officials believe that the SJP videocassettes have contributed significantly to a reduction in mine accidents.

Jan 1, 1985

It is well known that the crushing and grinding steps in the mineral processing of ores represent a substantial proportion of total energy, cost and carbon emission in mining. For instance a recent study calculated that 36% of the energy consumed by gold and copper producing mines in Australia was attributable to comminution (Ballantyne et al, 2012). Understanding this component of a business is essential in a world seeking to lower production costs, improve earnings and reduce its carbon footprint. The issue commands the attention and support of industry leaders in the mining sector, government, equipment manufacture, engineering design and research organizations. Furthermore, several researchers have often stated that globally, comminution processes consume between 3-4% of the world?s electrical energy production (Daniel and Lewis-Gray, 2011). In 2009-10, Australia?s Federal Government Energy Efficiency Opportunity (EEO) participants in the mining sector used 336.5 PJ, representing approximately 6 percent of Australia's total energy use. It is evident that the current practices of breaking rocks in tumbling mills are relatively inefficient (Fuerstenau and Abouzeid, 2002). Research and improved engineering design has established that a range of improved blasting, crushing and grinding techniques and flow sheets may lower project costs and carbon footprint. These include relatively simple process flow sheet strategies such as gangue rejection or pre-concentration prior to size reduction, a better combination of grinding technologies (both current and new systems), and selection of coarser grind sizes where ore and waste mineralogy allow. Yet, despite this systematic and detailed research, the industry remains somewhat reluctant to implement these strategies. CEEC (Coalition for Eco-Efficient Comminution) was established in 2011 to support knowledge sharing and change in an area of high-energy consumption for the global mineral industry. CEEC is a not-for-profit industry company, funded by grants from world wide industry companies, whose mission is to accelerate knowledge and technology transfer in the field of energy-efficient comminution. The key benefit to the mining sector arising from CEEC?s activities will be an increase in the rate at which more energy-efficient comminution data sets, processes, and technologies are developed, demonstrated, shared and applied. This will contribute directly to the industry?s target of reducing operating costs and carbon emissions. CEEC International Ltd and JKTech Pty Ltd teamed together to facilitate the inaugural CEEC Workshop, in June 2012. The purpose of the workshop was to produce a roadmap to provide guidelines for how (1) operations can achieve best EEC practice in the short to medium term, in collaboration with vendors, engineering companies and other service providers, and (2) what R&D is needed to achieve paradigm change in EEC in the medium to long term, e.g. 75% reduction in comminution energy in 10 years.

Sep 1, 2012

By A. B. Baldwin

"Uranium and thorium mineralization occurs at several localities in eastern Quebec along the north shore of the Gulf of St. Lawrence. The main occurrences are near Sept-Iles, Baie Johan Beetz, Romaine and St-Augustin river. Mineralization occurs mainly as disseminated uraninite, uranothorite, uranothorianite, monazite and minor zircon and allanite. Yellow to orange oxidation products are observed along fracture planes of the uranium-bearing deposits to a depth of a few feet. Magnetite, biotite and smoky quartz have a distinct tendency to accompany the radioactive minerals. The host rocks include white to pink pegmatite, pink granite and also, in the case of the Romaine and St-Augustin River occurrences, cream to grey plagioclase-rich, well foliated paragneiss and migmatite. Radioactivity near secondary structures, such as fractures and joint planes, indicates some reconstitution of radioactive minerals.The North Shore of Quebec is the northeast extension of the Grenville sub-province. It is also a uranium-thorium metallogenic province."

Jan 1, 1970

By Sowmiyaa. V. S., Tiruvengala Padma

Axial compression capacities of bored cast in situ piles as per Indian and International Standards are compared in this paper. Bored cast in-situ piles resting on soil and rock are considered for capacity assessment comparison. The standards considered for comparison are Indian Standards namely IS 2911-Part 1-Sec 2:2010 and IRC 78, International Standards like AASHTO LRFD Design-2017, API 2A WSD, BS 8004:2015 & EN 1997: Part 1:2014. The end bearing mobilization limits as proposed by various standards and their influence on longer piles in cohesive and cohesionless soils are discussed.

Sep 1, 2022

By Ralph Wilcox

The diamond drilling of certain characters of unstable rock formation, as, for example, the copper-bearing schists of the Miami district in Arizona, is rendered most difficult by what is known as a caving " of the sides of the drill holes. As this caving is very greatly increased by the action of flowing water, it occurred to me, after experiencing a great deal of difficulty with caving in diamond-drill holes which I was drilling for the Miami Copper Co., that if I could substitute air for water, much of the caving—with resultant difficulties, such as decreased speed of sinking and increased consumption of diamonds—would be overcome. After some experimenting, I found that it was perfectly practicable to substitute air for the water; forcing the air down the hollow rotating rods in the same manner as is done with water, the air passing out around the bit, which is thus cooled, and ascending on the out~ide of the rods to the collar of the hole, carrying the borings in just as satisfactory a manner as had been done by the water, but without the accompanying destruction or caving of the sides of the drill holes such as had been so generally experienced with the water. When water was encountered in the drilling this water was forced up to the collar just as it would have been had water been used in the drilling, but with the correspondingly decreased flow there was relatively less washing or caving of the sides of the drill holes. The only change necessary in the arrangement of the drill is that a cross instead of a tee is used at the collar of the hole. A tightly woven jute bag is attached to one arm of the cross, for collecting and filtering the sample; and when drilling in dry ground a jet of water is attached to the opposite arm of the cross, to collect the dust and wash down the sample into the bag. The rods rotate through a stuffing box attached to the upper opening of the cross. The distention of the jute bag by the issuing air indicates the operating conditions as sufficiently as did the flow of water when using water in the drill hole. The small percentage of core recovery rendered it necessary to

Jan 1, 1914

The world's largest steam-driven mine hoist, built by Nordberg Manufacturing Co. a half century ago, has become a major tourist attraction in Michigan's Upper Peninsula. The hoist, designed by company founder Bruno V. Nordberg, is located in the Quincy Mine Number Two, just north of Hancock. Nordberg began construction of the mammoth machine before World War I, but delayed completion until after the war. The hoist became operational in 1920 and continued running until the mine was shut down in 1931.

Jan 9, 1968

By John C. Draper

Little precise information is available on the effect of mining on the surface topography. It is often assumed that after mining the surface will simply sink. This is not an infallible conclusion as is well illustrated in two of the three examples herein. This paper describes the results of an attempt to precisely measure the surface movement in the area around coal pillars left in place for three oil wells in a completely mined and caved area at the Harwick Mine of the Duquesne Light Company. The dates when the various measurements were made are shown on the data sheets and indicate the rate of surface movement. These oil wells are identified as wells Nos. 2, 3, and 6. This mine property is located on the north side of the Allegheny River at Cheswick, Pennsylvania, and extends in a northerly and westerly direction about five miles. The three well pillars are situated on the westerly side of the Bessemer and Lake Erie Railroad some 2,000 feet from Rural Ridge, Pennsylvania (Fig, 1).

Jan 1, 1964

By A Jankovic, D David, P Payne

Although the majority of current steel production is supported by iron ore sourced from high-grade haematite deposits, the long-term growing demand for steel has led to higher raw material prices and opened the way for many new magnetite deposits to also be developed. There is a rich and long history of magnetite ore processing in Western countries, including large operations such as Cleveland Cliffs in the USA and LKAB in Sweden, as well as smaller operations like Savage River in Tasmania. The challenge for virtually all magnetite operations is to minimise operating costs, which is dominated by the cost of power required to fine grind the ore in order to achieve acceptable concentrate iron grade together with low impurity content. This remains the case today and will be even more important in the future when a carbon tax is expected to become a significant addition to the operating costs for magnetite deposits. Historically, the lowest operating cost was achieved by multistage fully autogenous grinding with integrated magnetic separation steps between the stages. The major benefit of fully autogenous grinding is the elimination of steel grinding media costs and the need to discriminate between steel and magnetite in coarse magnetic separation. The separation step between grinding stages progressively reduces the amount of material to be ground. Application of more efficient grinding technologies developed in the last 20 years, including high pressure grinding rolls (HPGR) for fine crushing and stirred milling for fine grinding, has provided opportunities to further reduce the operating costs associated with comminution. Both technologies are already implemented in some magnetite processing operations, although in limited capacity. The results of a theoretical option study for high capacity processing of a hard, fine-grained silica-rich magnetite ore is presented in this paper, with the emphasis on comminution circuit options. Several circuit options are ranked based on a net present value analysis incorporating an estimate of carbon tax added in the operating cost. The study demonstrates the significant advantages of applying more efficient autogenous grinding technologies.

Jan 1, 2009

By R. H. C. Andrew

With the advent in recent years qf mechanization in deep-level gold and platinum mines, large quantities of rubber was are being used on both production and support vehicles. Conditions in these types of mines are extremely harsh and, as a result, we performance is significantly lower than in other types of mining such as open-cast base metal mining, where more favourable conditions prevail. Various options are available to the user to reduce tyre costs, including the use of retreads, the filing of tyres, and the repair of damaged tyres. While these methods may be generally successful in open-cast conditions, their use in deep-level mining needs to be carefully evaluated for each particular set of conditions. A basic requirement for any evaluation of we costs is the availability of reliable data on tyre performance and, for this reason, it is essential that proper tyre records are maintained This paper reviews the performance of tyres in deep-level gold and platinum mines in Johannesburg Consolidated Investment Company, Limited (JCI) over a period of about 8 years, and shows how the costs of retreading and tyre filing can be evaluated in practice. It also discusses the cost implications of repairing damaged tyres.

Jan 1, 1994

By Mariana Carla Mendes Rodrigues

The present study deals with the effects of strain rate on the functional behavior of NiTi thin wires. The samples, in the austenitic condition at room temperature, were mechanically cycled 20 times by loading up to 6% strain followed by complete unloading, at 25°C. Four different quasi-static strain rates were assessed: 1x10-4, 1x10-3, 1x10-2 and 5x10-2s-1. The functional properties are described by means of critical stress to induce martensite, stress at maximum strain, energy dissipated per cycle and residual strain. The sensitivity of repeated cyclic deformation to strain rate is also analyzed in terms of phase stability. The results show that the fluctuation in the loading plateau, due to non-homogeneous transformation, increases with increasing strain rate. During cycling, it is observed that higher strain rates result in lower critical stress to induce martensite after the 5th cycle. However, the stress at maximum strain is higher at high strain rates, regardless the number of cycles. The accumulation of residual strain also increases with the strain rate due to the higher applied stress. During unloading, both the elastic deformation of stress-induced martensite and the reverse transformation seem to overlap at high strain rates. The dissipated energy behavior changes between the 1st and 20th cycle. No martensite is stabilized after training, but the intensity of the X-ray diffraction peaks of austenite increases with strain rate, as a result of stress relaxation.

Aug 17, 2017

By Stefan Boshkov, Malcolm T. Wane

The validity and accuracy of velocity measurements underground have been questioned repeatedly by those in mine ventilation work. The general disagreement on the subject is well illustrated in an AIME publication.' Although the presence of errors is readily admitted, their magnitudes are not known and often are described by practical operators merely as "great," "small," or "of no importance." The belief that errors are of academic interest only prevails because of a justifiable claim that actual volumes of air circulated are well in excess of those required by law and safe mining practices. Poor understanding of the source and nature of errors inherent in velocity measurements, coupled with questionable determination of cross-sectional area, result in faulty techniques for the purpose of expediting ventilation surveys and render doubtful the calculated volume. Often consistency of readings is confused with accuracy. A succession of check readings showing a maximum deviation of 5 pct in the measured value of velocity usually signifies nothing more than diligent application of technique in a stable ventilating current.

Nov 1, 1955

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the U.S. mining workforce who are potentially exposed to RCS [1,2] as various ore bodies are drilled, blasted, hauled by truck, crushed, screened/sized and transported to their destinations. To examine a method for assessing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on 80 miners across seven unique mining sites. The data were then collated and partitioned using a thresholding scheme to determine exposures that were in excess of 10 times the mean exposure for that worker. Focusing on these short-duration, high-magnitude exposures can provide insight into implementing controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20 percent or more by reducing exposures that occur during just 10 minutes of work per eight-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By W. B. Berwald

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gras association, has been studying actively for the past several years the problem of the flow of natural gas through high-pressure transmission lines. Numerous data on gas flow through pipe lines under many conditions of operation have been obtained by carefully conducted tests, and these data, together with all other available information, have been analyzed carefully to secure practical facts for the use of operators in designing pipe lines and determining the effects of different operating conditions on pipe-line capacities. The first procedure in initiating; this problem was to review, compile, and analyze all of the existing data on the flow of natural gas through pipe lines. Actual data applicable to pipe and operating conditions normally used in the transmission of natural gas were meager, and the several pipe line flow formulas developed by different investigators gave widely varying; results when applied to problems of pipe-line design. Therefore, further experimental work under conditions comparable to those found in transmitting natural gas was essential before any definite recommendations could be made.

Jan 1, 1931

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011