Search Documents

By M. J. Steffens

ESPLIM is a novel separation technique that combines the advantages of solvent extraction and electrostatic dispersion but its application in the extraction of nickel by the direct solvent extraction route and the effect of high electrostatic field on the stability of organics have not been explored. These were investigated in this study and it was found that the technique allows 97% extraction of the nickel in a single stage compared with 3 stages by the conventional solvent extraction. Also, three months of exposure to 5.0 kV under simulated operational conditions had no adverse effect on the stability of organics.

Jan 1, 2005

ShouSteel Mining Ltd., a subsidiary of ShouSteel (Group) Co., was founded in 1959 and is located in QianAn City in Hebei Province, China. ShouSteel?s pelletizing plant uses iron ore as a raw material combined with limestone, dolostone, or olivine, with bentonite as a binder. After mixing the raw materials and forming them into small, spherical balls, ShouSteel then fires pellets in kilns for hardening. The company sells the finished pellets as raw materials for blast furnaces used to produce industrial metals such as iron. ShouSteel?s handling capacity is approximately 24.5 Mt/a (27 million stpy) of ore. The company?s production capacity is 3.2 Mt/a (3.5 million stpy) of oxide pellets and 560 Mt (650 million st) of sinters. Until recently, ShouSteel Mining had not replaced its electronic scales in its series of ingredient chambers. Because of the wear and tear on these older scales, the weighing system began to encounter regular problems. The company experienced a high failure rate from the integrator, an unstable signal, weak anti-interference ability and low accuracy. ShouSteel also found that spare parts required during repairs were consistently high in cost and that system calibration was becoming increasingly frequent.

Jan 1, 2012

By S. Chander

A series of nonionic and anionic surfactants were tested to enhance the flotation response of a low rank coal. An ethoxylated octyl phenol and several polypropylene polyethylene block copolymers were tested as nonionic surfactants. The anionic surfactant was a dioctyl sulfosuccinate. All the surfactants employed improved the yield significantly but the influence on grade was complex. Separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents tested, a correlation between emulsifying power of the surfactant and flotation was observed. An increase in the number of droplets produced in surfactant containing systems was considered to be the main reason for increase in the yield. Since it increased the number of collisions between dodecane droplets and coal particles. When a surfactant was introduced into the flotation pulp prior to addition of dodecane, it decreased the benefits of the surfactant significantly. The decrease was attributed to an increase in the wettability of coal and a decrease in the surfactant available for emulsification. When a suitable surfactant was added as a solution dissolved in the oily collector, a considerable increase in yield was observed.

Jan 1, 1993

By William J. Douglas

Critical path modeling (CPM) has been used widely as a tool to manage large-scale projects having many activities which are conducted in series or parallel. The construction industry is a regular user of critical path modeling as a planning tool. In this context, the method is used to provide an orderly schedule for all activities to forecast delays, slippages, and problem areas and to identify critical activities where resources should be directed. It also identifies others which have slack time, and provides information on the degrees of freedom and flexibility available in completing the project. The purpose of applying critical path modeling to an underground mining system is not primarily for scheduling, but as an analysis tool. In observing underground mining systems, it Is clear that repeated sequences of activities must take place for mining to proceed efficiently. Some of these activities must be sequential, while others be carried out in parallel. The fundamental difference between critical path modeling applied to mining versus a large-scale construction project are: (1) The activities in a mining system are cyclic in nature. (2) The location of the activity varies, and the entire process is not thought of as co-located, as is the case in a construction project. Another important aspect of the network development for mining systems is the degree of detail that is desired. One can be concerned with very macroscopic networks which represent, for example, an entire mine life cycle. Networks representing this problem would be more closely analogous to those of a large construction project. On the other hand, one might be interested in evaluating alternative ways of developing a property or of mining in a given section. More detailed networks representing the section activities are necessary to evaluate system parameters and their impact on long-term production.

Jan 1, 1978

By T. J. Morris

"From November 2014 through September 2016, Westmoreland’s Coal Valley Mine utilized a Marion 7450 electric walking dragline to extract 1.2 million tonnes of a vertically-dipping, 52-meter wide, fault-thickened seam, beneath a conventionally-excavated pit bottom. Mine planning and operational hurdles encountered throughout a kilometer of mined strike length included mitigating highwall instability in both hanging and footwall slopes, water management, and end-of-life machine reliability and maintenance. The most substantial challenge has been the depressed global coal market. However, the successful application of this mining method significantly aided the overall cost of production at the site. The valuable experience gained from this project will be extended to future mining areas where this technique can be similarly applied. INTRODUCTION Coal Valley Mine is located approximately 220 kilometers southwest of Edmonton, Alberta, Canada, in the foothills of the Rocky Mountains. Since commercial production began in 1978, more than 84 million clean tonnes of coal has been produced and sold domestically as well as exported overseas for power generation. While the existing processing plant has a nameplate capacity of 4 million tonnes per year, the site has operated at a 2 million tonne rate since 2015 due to depressed export markets. Westmoreland acquired the mine as part of its purchase of Sherritt Coal Operations in April 2014. The mine operates 24 hours a day, 7 days a week, with an IUOE workforce of 261. GEOLOGICAL SETTING The geology of the Yellowhead Tower mining area differs significantly from previous mining areas at Coal Valley. The Mynheer coal seam discussed herein consists of steeply dipping, highly-sheared, thrust-faulted, and heterogeneous coal pods. Deep set, southwest striking thrust faults were the likely mechanism for the podding and have resulted in overturned, rolled and highly sheared seams with zone thicknesses of up to 65 meters.The hanging wall is characterized by soft bentonitic mudstones and siltstones, overlain by massive competent sandstone. The footwall is defined by a hard volcanic tuff, interbedded with thin, sporadic coal seams. The sandstone above and volcanic tuff below constrained the faulting system within this zone, enabling the mass podding that has afforded the opportunity for large-scale mining."

Jan 1, 2017

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (K. McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project will be completed in early 1998.

Jan 1, 1998

By K. H. McDaniel

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modi tying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identity and quantity operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By H E. S Moorcroft, D Scott

The increasing mining depths of South African gold mine deposits are resulting in ever-increasing heat loads associated with depth and the geothermal gradient. Together with changes in the mining horizons brought about by the depletion of older, shallower, high-grade reserves, this leads to the need for the continuous review and redesign of cooling requirements. Traditionally, cooling requirements were met by using a combination of cooling strategies, including bulk air cooling on surface and underground. If this proved to be insufficient, chilled service water and secondary remote air-cooling systems were introduced. This paper reviews these practices in order to provide a cost-effective means of catering for the introduction of hydropower at the Gold Fields Ltd South African operations. Some of the equipment that has been developed to meet the requirements of both hydropower and refrigeration includes hydropower fans, cooling coils and in-stope venturis. These are individually described and discussed, together with their roles within the greater strategy. The planned change in the cooling strategy and the employment of these technologies have effectively doubled the cooling available, from 10 MW to more than 20 MW, extracted from the hydropower water used to drive the mining equipment. In conclusion, the cooling strategy described allows a total heat load of approximately 52 MW to be successfully ventilated and cooled through the use of combined surface and underground refrigeration installations, and through the use of hydropower-chilled water.

Jan 1, 2005

By D. W. Butner

This Information Circular , one of a series published by the Bureau of Mines , reports on the methods and costs of mining and concentrating zinclead ore at the Highland Surprise mine in the Pine Creek area of the Coeur d'Alene region of Idaho . The mine is owned and operated by the Highland Surprise Consolidated Mining Co. , which supervises operations of the Nevada Stewart group of claims , which is adjacent on the northwest . These properties are at the extreme eastern end of a zone of fracturing that strikes northwest across the Pine Creek area . In fractures along this zone are the principal Pine Creek mines ; these are the Highland Surprise , Nevada Stewart , Sidney , Denver , V and Idaho , Liberal King , and Northern Light . Country rock at the Highland Surprise is argillite of the Prichard formation (Belt series ) . Fracturing has permitted the movement of mineral- izing agents that have replaced adjacent walls and crushed country rock with sulfides . Ore minerals are sphalerite and galena with accessory pyrite , chalcopyrite , pyrrhotite , and siderite . Three principal ore shoots were found on the Highland Surprise property . The Highland ore shoot was mined from outcrop to the 400 level . The Surprise ore body has been developed to a depth of 1,400 feet on the dip of the vein . The outcrop of the Surprise ore shoot was 150 feet long and 2 to 4 feet thick ; on the 1,150 ( lowest ) level , the ore shoot is 320 feet long and 10 to 17 feet thick , with good zinc content . Surprise ore shoot No. 2 occurs 250 feet west of No. 1 and has been mined from the 500 to the 1,000 level . From 353,000 tons of ore mined between 1910 and 1948 , the property has a recorded production of 256,000 ounces of silver , 7,500 tons of lead , 24,000 tons of zinc , and 412 tons of copper . Both shrinkage and cut and fill stoping methods are used at the Highland Surprise , but shrinkage is unsuitable for mining below the 700 level , because faulting has weakened the walls . Development of the Surprise ore , as well as exploration laterally and along the strike , is prosecuted steadily . A prospect heading is being pushed westward toward Nevada Stewart ground from the 700 level . The mill has a rated capacity of 275 tons per day and operates near capacity . Selective flotation makes zinc concentrate that is shipped to the Anaconda smelter and lead concentrate that is trucked to the Bunker Hill smelter at Kellogg .

Mar 1, 1950

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating improved technology for mineral flotation. A variable often neglected in flotation control is redox potential. The use of redox control is illustrated by the separation of molybdenite from chalcopyrite. Laboratory testing showed that redox potential had a greater effect on product quality than collector addition. A significant need in froth flotation is greater reliability of the sensors used in measuring and controlling redox potential in mineral slurries. The USBM has developed an automated method for removing scale and reconditioning gold redox-sensing electrodes. Fouled electrodes are anodically polarized to 1.2 V versus the AglAgCI reference potential to remove scale. The electrodes then are conditioned by a brief potentiodynamic treatment to re-establish electrochemical equilibrium. In laboratory tests, this technique removed calcarious deposits from gold electrodes and reconditioned them for useful service in approximately 10 min. In plant practice, this technique would obviate the need for plant operators to manually polish electrodes, and also should result in greater reliability in redox measurements. Inexpensive, automated equipment to condition electrodes in a plant setting is described.

Jan 1, 1995

By C. R. Ross

"The purpose of this paper is to review the activities of international organizations concerned with the problem of dust hazards in mines and to indicate the extent of Canadian participation in these activities. The work of the International Labour Office in sponsoring conferences and reports on the appraisal and control of dust hazards and in the development of standard radio-logical classifications is considered in some detail. Also discussed are the role of technical societies, such as the American Conference of Government Industrial Hygienists, in the development of proposed standards for dust exposure and the functions of international committees concerned with particular hazards, such as the U.I.C.C. (Inter-national Union Against Cancer) Committee on Asbestos and Cancer."

Jan 1, 1969

By W. M. Williams

The Canadian steel industry is now in many ways a mature one, having achieved many technical successes during its hundred-year history. It is interesting to look back over this period, to learn something of the histories of the different producers and of the people and forces that shaped their development. The following article provides a thumbnail sketch of the Canadian steel industry as it exists today. It is intended for the general reader, not for the specialist who will want to consult the several books and theses written on the development of the industry during the last hundred years. The famous Les Forges du Saint-Maurice, an important iron producer for a century and a half, provides a natural historical starting point for a look at the four major players - Dosco, Algoma, Stelco and Dofasco - who have provided most of the hundreds of millions of tonnes of steel, in every form from horseshoes to tinplate, needed in the twentieth century. The smaller companies which have sprung up in the last 20 or 30 years are dealt with briefly - but only because their history is so recent. Not so long ago the mini-mill, based on scrap rather than on the blast furnace, was thought to be specially suited to the economies of the smaller developing countries of the Third World. However, recent history has made it evident that the small plant, specializing in a few basic products (e.g. reinforcing bar) or taking advantage of special circumstances, can successfully compete with the large blast furnace/primary steel producers.

Jan 1, 1999

By A. B. Parsons

LECTURE, it appears, is a discourse that is supposed to be instructive. I am quite sure that you will derive no instruction from what I have to say. I will be satisfied if my remarks provoke thought along one or two mental paths that have not been traveled so fre¬quently as to be devoid of interest. I have no particular message apropos of professional engineers or professional engineering, and any conclusions that I may seem to reach will be purely tentative and incidental. Probably at times you have wondered, in a casual way at least, why so many people who are not, never have been, and never will be engineers, want to use the title. For example, I recently received a communication from a life insurance broker or salesman, whose chaste letterhead bore the legend "Estate Engineer." He was perfectly serious about it, as is also the expert accountant who assumes the imposing name of cost-analysis engineer. Dozens of equally amazing titles might be cited. Then there is that class of individuals who have been engineers, in the true sense of the word; who have gone into some other kind of occupation; but who cling tenaciously to the name engineer, usually prefixing some word or other which at once gives them away by telling what their work really is. For example, we have such pseudomorphs as the management engineer, and the sales engineer. It is quite evident that engineer is a word to conjure with. Evidently both the man who appro¬priates the designation without any justification and the ex-engineer who persists in calling himself an engineer even after he has abandoned engineer-

Jan 1, 1933

By S W. Houlding

The Certificate in Mining Studies program at the University of British Columbia, Vancouver, Canada is a collaborative initiative between mining schools and industry to provide accessible, cost-effective, accredited continuing education and training, designed to address the future needs of the global mining community. Content is provided by industry specialists and delivered through an integration of online learning, short courses and interactive webcasts. Accreditation is provided by a network of mining schools. In 2011, the program will deliver close to 100 short courses and interactive webcasts and provide 24/7 access to more than 130 online courses in six mining streams, to participants from as far afield as Tanzania, Argentina and Mongolia. The program is proving adaptable to corporate and mine site engineer-in-training and graduate-development programs, as well as providing accessible professional development opportunities for individuals. It also provides opportunities for cross-training from other disciplines and integration with mining school curricula.

Nov 22, 2011

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006

By F. J. Gallagher

"INTRODUCTION The purpose of this circular is to present information on the construction and use of reinforced rubber-jatketed tubing and insulatiag air-line couplings in coal mines Where Airdox is used for breaking coal in order to eliminate: insofar as possible, arcing at the face between Airdox tubing and the track or other face equipment.ACKNOWLEDGMENTThe information given by the W. M. Hales Co., Chicago, Ill and the Peabody Coal Co., Taylorville, Ill., regarding the construction and use of rubber-jacketed tubing and insulating couplings in gratefully acknowledged. GENERAL INFORMATIONSince its introduction into coal mines, the use of Airdox has grown in popularity, especially in the Indiana and Illinois coal fields. Its use permits breaking dawn coal on shift, whereas the use of explosives for blasting coal on shift is prohibited by law in those States. Many of the hazards connected with the use of explosives are eliminated. The accident experience in the use of Airdox has been excellent with respect to the number of fatalities or serious injuries per million tons mined.The Federal Mine Safety Code specifies that Airdox lines should be grounded at the compressor and at other points of low resistance along the lines but should not be connected to tracks, pipe lines, or other possible power conductors. The majority of operators in the Indiana and Illinois coal mines, in which Airdox is used, approve the precautions embodied in the code regulationsIf Airdox lines are grounded in accordance with the Code, the following hazards persist:"

Sep 1, 1949

By William C. Cooley

A review was made of two Russian books and a chapter from a third book dealing with pipeline transport of coal. Emphasis was placed on hydrotransport of coarse coal in underground mines or surface pipelines. The books reviewed were: "Means of Increasing the Effectiveness of Hydrotransport," by V. N. Pokrovskaya (1972), "Parameters and Modes of Hydraulic Transport of Coal" by V. V. Traynis (1970), and the chapter "Calculations of Hydrotransport of Useful Minerals and Waste Rock" from the book "Hydromechanization of Opencast Workings" by G. A. Nurok (1970). All three are unique and useful additions to the world literature on hydrotransport. The Traynis book reveals the development and results of circular wheel stand tests to simulate hydrotransport in horizontal pipes, which is a potentially outstanding contribution to slurry pipeline technology. Graphical data and equations are presented which suggest that headlosses for coarse coal can be predicted with good accuracy for pipe sizes up to 14 inches in diameter. Wheel stands permit tests for pipe wear and lump degradation without recycling coal through pumps. Recommendations are made for wheel stand tests and for correlation of existing data.

Jan 1, 1976

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By Kathy Kalenchuk

To develop strategic and tactical strategies to manage seismic hazard in a safe and economic manner, it is necessary to understand the spatial and temporal distribution of mine wide seismogenic behavior. Global mine-scale numerical stress modelling provides a means to forward predict seismic susceptibility thereby facilitating informed decision making for the development and implementation of strategic and tactical risk mitigation measures. To make forward predictions of hazard susceptibility using global stress models with reasonable confidence, it is necessary to rigorously calibrate numerical stress models to the observed history of ground reaction. This paper demonstrates quantifiable methods for calibrating numerical models and developing probabilistic prediction criterion using seismic data. The appropriate applications of model inputs (including boundary conditions, constitutive models and material parameterization) specific to global mine-scale modelling are also discussed. Lastly, this paper demonstrates how the calibration process adds value not only to informed decision making, but also to the improved understanding of site geomechanical conditions; including enhanced identification of geotechnical domains and mechanical indicators required for seismic mechanism domaining.

Apr 26, 2022