Search Documents

By Sathit Tandanand

This report presents a Bureau of Mines study on the time-dependent behavior of coal measure rocks for future implementation in stability analysis and safety evaluation of in-mine rock structures. This initial study focused on moisture adsorption rate and strength degradation of shales in Pennsylvanian coal-bearing strata in the Illinois Basin. A reaction of clay minerals in Illinois shales with atmospheric water vapor was hypothesized as the adsorption and strength degradation mechanism. Part of energy exchange between shales and the environment was attributed to a free energy controlled by pore pressure of the rock and partial pressure in the environment. The relationships between adsorption versus time and strength degradation versus moisture content were derived and correlated with the experimental data. Partial saturation at various levels of relative humidity occurs within approximately 2 weeks at room temperature. The strength of shales tested decreases linearly with increasing moisture content. When the moisture exceeds 7 pct of the dry weight, these Illinois shales become unstable. To this end, the moisture content is a good predictor of rock strength for shales.

Jan 1, 1987

By A. Gontijo, A. Matos, P. Lincoln, L. Fonsecail

This paper investigates how to manage and model the vibrations caused by rock blasting in a Brazilian underground mine. Considering the frequent detonations and the previous lack of effective vibration control, understanding, and reducing the impact of these seismic waves is critical. We emphasize the use of the near field model technique, which considers the varied physical properties of different rocks, optimizes blasting plans, and minimizes damage to the rock mass. We detail a case study that demonstrates a comprehensive approach to vibration control. The discussion includes the creation of a monitoring plan, the methodology used, results and the specific challenges and solutions found during the blasting process. This study provides a practical guide for similar future projects. Finally, we present a predictive model based on the collected data, offering insights into the vibrations caused by blasting. This model helps decision-makers minimize the risk of displacing rock blocks in the blasting area, improving safety and operational efficiency

Jan 1, 2024

By C A. Cooper, G A. Suter

The sizing of a starter dam for a Tailings Storage Facility (TSF) involves balancing many competing demands. It should cost as little as possible, be high enough to store tailings until the first raise can be constructed, it must be able to contain water safely, and it must be designed in such a way that the long-term integrity of the higher raises are not compromised, among other things. In addition to these demands there is the complication of the behaviour of the process plant, and the tailings during commissioning. Variations in slurry density, excess water in the TSF, initial settled density of the tailings, reliability issues, and beach slopes above and below water can all impact the way the tailings beaches are developed and ultimately impact the ability of the starter dyke to contain the required volume of tailings and water.The conventional approach to the design of a TSF starter dyke is to begin looking at the elevation required for a set of deterministic design parameters, find ways to reduce the size or volume of it as much as possible to reduce cost, and then possibly look at the sensitivity of some of the input parameters. This paper discusses a stochastic modelling approach for starter dykes that allows a wide range of design inputs to be simulated quickly, with an envelope of possible results produced. The sensitivity to different parameters can also be examined to understand which design inputs have the biggest impact on the required dyke sizing. By integrating the 3D TSF modelling tool Muk3D with GoldSim, it will be demonstrated how a wide range of scenarios can be evaluated and how that information can be used to make better decisions about the selection of design options.CITATION:Cooper, C A and Suter, G A, 2018. Starter dyke optimisation with Muk3D and GoldSim, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 466–475 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Marcio Toshio Tanaka, Marcelo Breda Mourao, Cyro Takano, Cesar Yuji Narita

"The concerns in questions related to the environmental impact in the steelmaking industries caused mainly on the gas emissions such as the dioxide carbon are due to its raw material such as the coal, a fossil and non renewable resource. The purpose of this paper is to replace from 10% to 50% of the coal used in cokemaking by mixing it with a renewable source (wood charcoal). The powder (- 325 mesh) from both raw materials (coal and wood charcoal) were mixed in order to obtain a briquette that was then heat treated at 1100°C to obtain the biocoke. Results of usual analysis (coke reactivity index, coke strength after reaction and cold crushing strength test) were employed to compare to regular coke briquettes. It was found that biocoke with different amounts of wood charcoal present features enabling it to be used in some ore reductionprocesses.1. IntroductionThe iron and steelmaking industry is a heavy emitter of carbon dioxide; according to the World Steel Association, 6.5% of global emissions of this greenhouse gas is due to the production of ferrous materials [ 1]. This is due to the fact that the fuel and reductant employed in the blast furnace is metallurgical coke, obtained from fossil coal. There are some projects aiming to reduce or even eliminate the emission of fossil GHG in the iron and steelmaking process [2]. Most of them propose the capture and storage of the gas (CCS) [3], a technology not yet proven. Other studies point out that the coke consumption in the blast furnace could be reduced by using high reactivity coke; this could lead to lower temperatures in the thermal reserve zone of the blast furnace and consequently less fuel rate in the furnace.The use of biomass in the iron ore reduction process is known as an environmentally accepted solution, as biomass does not release already fossilized carbon."

Jan 1, 2013

Introduction One hundred years ago, a recent college graduate created the US aluminum industry. He found an economic way to crack the primeval bond that makes the metal so special. Aluminum doesn't "rust" - oxidize progressively. Rather, when exposed to air, it instantly forms a gem-hard but microscopic oxide coating. This seals off oxygen from the metal underneath. Scratch it and the seal reforms instantly. That tight chemical bond is the reason the metal is not found in nature; it exists only as a compound. The bond had to be broken to free the shiny metal. But once it is free, that self-sealing protection, alongside a remarkable strength-to-weight ratio, offers a marvelous material. Until 100 years ago, finding a way to do that economically was a challenge that defied science. Then it was solved, in a remarkable coincidence, on both sides of the Atlantic. And the way was paved for a material that would become the second most widely used metal in the world. Until that time, aluminum was a rare and precious metal. But then two young scientists independently invented the process that took aluminum outside the laboratory and into applications ranging from pots and pans to spacecraft. Discovery of aluminum Other major metals - copper, iron, lead, gold, and silver - had been used for thousands of years. But aluminum was entirely unknown until 1782, when French chemist Antoine Lavoisier suspected its presence. It was not actually discovered until Sir Humphry Davy, in England, detected it in clay in 1807. It was first isolated as a free metal only in 1825, by Denmark's Hans Christian Oersted. For years, laboratory methods yielded aluminum only in tiny amounts costing about $1200/kg ($545 per lb) - $13,333/kg ($6000 per lb) in today's dollars. Methods developed by French scientist Henri Sainte-Claire Deville in 1854 cut the cost to about $200/kg ($90 per lb). King Frederick VII of Denmark had a helmet of aluminum and gold. And Emperor Napoleon III of France reportedly served his most exalted guests at a state dinner with aluminum plates. He left the lower ranks to dine from pure gold. Deville and others continued to reduce production costs. But the price of aluminum still rivaled silver - $31/kg ($14 per lb) versus about $35/kg ($16 per lb) for silver. Then in 1884, a 2.8-kg (6.25-1b), 230-mm-tall (9-in.-tall) aluminum pyramid was cast as the tip of the Washington Monument. It was probably the first architectural use of aluminum. And it is still there after more than a century. The attractive properties of aluminum were obvious: it is lightweight but strong, conducts heat and electricity, reflects light and other electromagnetic radiation, and resists corrosion. But its commercial promise was blocked by its cost. In 1885, the price of aluminum was $17.70/kg ($8 per lb). It stayed there for the next couple of years until the Hall-Heroult process brought it down sharply. Hall-Heroult process lowers aluminum costs The characteristic that kept aluminum hidden so long continued to thwart chemists. Aluminum clings to oxygen so tightly that it is never found as a free metal in nature, and it is hard to break that bond chemically. The best chemical methods of the 1880s required sodium, and sodium itself was expensive. At Oberlin College in Ohio, chemistry professor Frank Fanning Jewett advised his students that anyone who could make aluminum inexpensive would do humanity a favor and get rich as well.

Jan 3, 1987

By William M. Kester

Finely sized Upper Freeport coals are beneficiated to reduce ash and sulfur using high-intensity magnetic separation to process both (1) raw, untreated coal as well as (2) raw coal which was pre-treated thermally with steam and air. Substantial, sulfur and ash reduction can be obtained using both approaches to magnetic beneficiation of coal fines, but evidence indicates that pre-treatment which would constitute a costly supplementary step is technically inferior to the direct beneficiation of raw, untreated coal. These bench-scale studies demonstrate that if high-intensity,; high capacity, dry, magnetic beneficiation equipment can be developed and' installed at coal burning power plants or at appropriate points in coal preparation plants substantial quantities of sulfur may be removable from coal after pulverization as a means' to reduce air pollution.

Jan 1, 1965

By E. Swartzman

"DURING 1951, experimental cleaning studies on both fines and larger sizes of certain Canadian coals were conducted on a relatively large scale in two pilot plants in the United States, large enough to be considered as small commercial units, and in one commercial plant in Canada.One of the pilot plants was a wet washer of a type which apparently has never been .used in Canada, nor has any Canadian coal been tested in it before. In the other pilot plant and in the commercial plant, dry cleaning equipment was used. The commercial plant is the first of its kind to be employed in Canada, and this type is used only to a limited extent in the United States.Fine-Coal Cleaning ExperimentsTest PlantsHydrotator and Hydrotator-Classifier combination pilot-plant with a capacity of about twenty tons per hour. This is a classifier type washer adapted for cleaning fine coal as well as certain intermediate sizes. The Hydrotator deals with that portion of a coal retained on approximately a 24-mesh Tyler sieve, whereas the Hydrotator-Classifier deals with the minus 24-mesh fines."

Jan 1, 1952

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By B. A. Bancroft

A quality assurance program consists of all those activities aimed at providing confidence to the purchaser that the suppliers quality system will provide a product that will satisfy the purchaser's stated quality requirement. An organizing principle is necessary for prioritizing the quality control activities of quality personnel in the face of a myriad of technical possibilities, data-analytic applications, and an overwhelming number of possible activities promoted in the literature and by quality "gurus". The organizing principle I like is that quality assurance exists when those involved in the quality process: (1) know what they are supposed to do, (2) can tell if they are doing it and are set up to continue doing it and, (3) if they are not, they can remedy the situation in a timely fashion. Any incremental activity which facilitates this organizing principle is a continuous improvement activity. That activity which has the chance to facilitate this principle to the greatest extent is the next one to work on. In these days of lean corporate and regional staffs it is as important to know what not to work on as it is to know what to work on. In this paper I shall discuss in general terms the implications of this organizing principle for the design of Quality Assurance (QA) Programs for coal mines and also provide some comments about the application of Statistical Process Control (SPC) methodologies in the coal industry.

Jan 1, 1994

By S. P. Ball

A major limitation to maximising the rate of gold extraction in commercial operations occurs as a consequence of the limited solubility of oxygen in cyanide liquors. The use of additions of solid inorganic peroxides as an in-situ supply of oxygen to the lixiviant has been studied, in particular in its application to heap leaching. Experimental studies showed-that the release of oxygen into solution from these peroxides is very sensitive to solution pH. Agitated leaching tests showed that, when either Ba, Ca or Sr peroxides were used as the-sole source of oxygen, both the rate and extent of gold extraccion was enhanced. Column leach tests were used to simulate heap leach conditions. These showed that significant increases in the rate of gold extraction could be achieved by additions of calcium peroxide, made to the ore, prior to it being loaded into the columns.

Jan 1, 1989

By J. Font

The RAF or copper fire refining process at the Caletones smelter of CodelcoChile consists of several pyrorefining stages that successively lowers the levels of S, Fe, Pb, As, Sb, Te, Se and to some extent 0 in the copper melt, allowing the production of high quality fire-refined copper of 99.93 % purity (RAF copper). This chemical feature of the RAF copper is only achieved by quite long processing times, and a considerable consumption of fluxes and fuels in the RAF vessels. The main goal of this study was to improve the RAF process performance by thermodynamic considerations and industrial scale tests, i.e., an in situ approach for the process as featured by intensive sampling, characterization and subsequent modifications. Thus, both theoretical and industrial data were derived, and based on kinetic and thermodynamic evaluations, a higher operational standard was achieved for the RAF process. These new operational practices allowed enhancing the overall economic of the RAF process, by reducing the time and operational costs, and consequently increasing the availability of the vessels.

Jan 1, 2007

By William Gleason

While a fleet of 100 t (110 st) haul trucks were busy removing overburden from the open pit mine in the distance, a host of dignitaries, including congressmen and California state representatives, gathered for Molycorp?s official groundbreaking ceremony at the Mountain Pass Mine on April 20. The mine, recognized as arguably one of the richest rare earths deposits in the world, is at the center of Molycorps? strategic ?Mine to Magnets? plan. It aims to secure America?s future supply of rare-earth-dependent technologies by developing a strong domestic rare earth industry. Molycorp identifies rare-earth-dependent technologies as those that cannot be produced without rare earth materials. The list of these technologies is long and growing. It encompasses everything from personal electronics and batteries for hybrid cars to permanent magnet generator wind turbines and national defense applications.

Jan 1, 2011

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983

By L. B. Beneitone

Over the years, the rope changing procedure on the two double-drum San Manuel ore hoists has been streamlined and improved, so that a job that once required eight hours to complete is now finished in four. The ropes, constructed of improved plow steel, 6 x 25 filler wire, pre-formed, right lay, Lang lay with a fiber core and weighing 8 ½ lb per ft, have a 2 ¼ in. diam and are 3200 ft long. They have widely varying lives, but on the average a rope change on one of the two hoists is required every six months. When a rope change becomes necessary, the ropes on both drums of a hoist are replaced. Thorough planning and preparation are essential for efficient rope changes. A briefing session is held on the day prior to the change, during which the entire procedure is reviewed on a blackboard and discussed among the cable rigging crew. These discussions have led to many improvements that have been incorporated into the present rope changing procedure.

Jan 4, 1968

By Theodore J. Hoover

WHAT are the chief branches of the mining engineering profession today? In an effort to analyze the structure of the profession, for practical purposes, a quantitative study has been made of the membership of the A.I.M.E., and is herein reported for the first time. In spite of the effect that a long history and a relatively small group of professional workers have had in limiting specialization in mining engineering, there has nevertheless grown up a wide variety of specialties in this field. More than a hundred different kinds of engineers were discovered among the titles given by Institute members in the Directory, ranging from "advisory engineer" and "American engineer" down to "wire-rope engineer" and "works engineer." How should all these titles be defined and interpreted? How many of them should be relegated as meaningless or confusing? What are the relationships among the remaining useful designations? Should some of them be grouped as "metallurgical" or "chemical," or under some other head?

Jan 1, 1935

By John P. Powell

A comprehensive study of the effects of hydraulically fracturing water-flood wells in Oklahoma has been made by the Federal Bureau of Mines. This report presents results of that study and an analysis of some of the factors governing the results of fracture treatment on waterflood properties. Originally, hydraulic fracturing was used to stimulate oil production from old wells producing by primary methods, and its application to water-flooding was regarded with skepticism by most producers. However, since 1953 the number of fracture treatments of both oil and input wells in waterfloods has increased steadily. Hydraulic-fracture treatments in waterfloods have generally been successful in stimulating production from oil wells and increasing the rate of injection into input wells. Hydraulic fracturing has enabled several producers to turn probable failures into economically successful projects.

Jan 1, 1961

By Helen E. Edwards

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy facilitating the theoretical study of flame and combustion phenomena. This report is the third of a series3/ presenting results of the study for particular fuel-oxidant systems. The equilibrium composition of the products of combustion and the adiabatic flame temperatures of specified oxyacetylene systems have been computed.

Jan 1, 1953

Operating Characteristics of Centrifugal Fans and Use of Fan Performance Curve Discussion of paper by. Louis W. HUBER, presented at the New York Meeting, 1926, .and issued, as Pamphlet No. 1542-A, with MINING AND METALLURGY, February, 1926. G. BRIGHT, Pittsburgh, Pa.-Apparently from the pressure curves for a forward-curved-blade fan, in Mr. Huber's paper, practically all ventilation-might be stopped with increased resistance. In order, to discuss the characteristics of a fan we need, some better way to measure the characteristics of a mine. You all know that. the average anemometer is not very-reliable. Sometimes two anemometers, supposed to be recently calibrated, will differ 50 per cent. Either this or some other committee should standardize measuring methods. The characteristic curves of fans, given by Mr. Huber, would indicate that the forward-curved-blade fan would cause trouble in attempting parallel operation, because two machines will not parallel unless they have dropping pressure characteristics. On the other hand, it is indicated that with the backward-curved blade, they could easily be paralleled. But few mines use more than one fan. Mr. Huber said that if the resistance of the mine was considerably more than contemplated, the quantity of air might be such that the efficiency of the backward-curved fan would be seriously affected, dropping say from 70 to 55 or 50 per cent. In such event, could a difference of speed be selected for the fan that would give the quantity desired at a higher efficiency? L. W. HUBER, Pittsburgh, Pa.-The backward-curved-blade fan responds to change in speed the same as any other fan; if' the speed is doubled, the quantity of air is doubled, the pressure is increased four times and the horsepower eight times. One point not mentioned in the paper is that the backward-curved fan is more efficient than the forward-curved or any other type. If the latter were more efficient, it would pay to install that type and keep the resistance of the mine constant, which is hard to do but it can be done with care. But the total mechanical efficiency of a fan with backward-curved blades is from 10 to 20 per cent. higher.

Jan 1, 1927

By James N. Brentz

This paper deals briefly with the problem of efficiently selecting the most cost effective haulage truck. Problems and factors are identified that effect productivity and operating cost. Despite the sophistication of computerized vehicle simulation programs, there is a wide disparity in accuracy and methodology, particularly in dealing with the various elements of cost.

Jan 1, 1984

By H. H. Stoek

It would permit coal mines to operate continuously instead of intermittently . Intermittent operation increases the cost per ton for mining , and makes the yearly return to labor low . These conditions contribute to serious instability and unrest in one of the fundamental industries of the country and this can be changed only by coal buyers doing their part to insure steady work . The railroads are now required to transport the maximum amount of coal during the winter months when traffic is most interfered with by bad weather and when the maximum amount of coal is used by the railroads to handle other coal . The railroads now use nearly 30 per cent of the total output of coal . About one- third of their freight traffic is hauling coal , so that economy of fuel used by the railroads will produce a considerable gross saving .

Apr 1, 1920