Search Documents

By John Nagy, Austin R. Cooper

Information is presented on the pressure and rate of pressure development during a dust explosion . The data were obtained in laboratory studies in a 75- cubic inch vessel with mineral , agricultural and chemical dusts . The factors investigated include dust concentration , oxygen concentration of the atmosphere , admixed inert powder , and admixed moisture . Information is given also on the effects of these factors on the composition of the atmosphere after the explosion .

Jan 1, 1964

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By Jack Mantel

The goal of this 42-month contract was to increase safety in low-seam underground coal mines through development and in-mine evaluation of a temporary roof support system for roof drills and floor-riding operator compartments for a loader and shuttle car. The program was performed in three phases. During Phase I, state-of-the-art canopy technology was investigated, and preliminary design and mock-up evaluations were performed for temporary roof supports for single-and dual-boom bolters and for transverse-mounted floor-riding canopies for a shuttle car and coal loading machine. The shuttle car and loader canopies were approved for further development, and the design, fabrication, testing, and certification were completed in Phase II. In Phase III, the Bureau of Mines furnished an FMC 6L shuttle car fur use in the evaluation of the canopy for 45 shifts. The shuttle car canopy was evaluated at Virginia Crews Coal Company in West Virginia. Efforts to secure an evaluation site for the loader canopy were unsuccessful. The loader canopy was shipped to Bruceton for possible future evaluation.

Jan 1, 1985

Shortly after Denny, Robson, and Irwin published their first paper in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery.It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter's source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in:(1) Speakers on machine columns, vibrated by drills.(2) Vials placed in drill holes to be blasted.(3) Both homogeneous and heterogeneous mixture with explosives.(4) Packages with tamping.(5) Compressed-air lines.(6) Special compressed-air ejectors for use while drilling and after blasting.(7) The discharge of ventilation fans.(8) The filters of respirators.It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium p;wder, and would interfere unduly with underground routine.Later, animal experiments by Denny, Robson, and Irwin2 showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.APPARATUS USED IN THE DEVELOPMENT OF ALUMINIUM PROPHYLAXIS SAMPLINGA basic requirement was a method of sampling to assess accurately the particle-size concentrations of dispersed aluminium powder. Konimetry, though regularly practised at McIrityre, was inadequate for the research in mind. On the other hand, the efficiency of the thermal precipitator was recognized as being very high. Accordingly, the latter instrument was chosen as best suited to our needs. Through the courtesy of the Ontario...

Jan 1, 1945

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Gas holdup profiles in the collection zones of a pilot flotation column (0.91 m x 13.5 m) and a laboratory flotation column (0.057 m x 9.5 m) operated with air and water only were determined from pressure measurements. The profiles were determined discretely and continuously. For the pilot column, a minimum distance between pressure measurements was necessary to give reliable results. For the laboratory column, a third-degree polynomial fit to the pressure vs. height data was required. Water manometers proved to be less sensitive to sensor and process noise than pressure transducers. The profiles showed that gas holdup approximately doubled over a height of 8 to 10 m. The profiles were not linear, and the gradient increased towards the top of the column, especially for gas rates greater than 1 cm/s. The profiles cannot be predicted by a simple bubble expansion model. The implications of this new finding of a significant gas holdup increase with height in the collection zone on various aspects of flotation column design and operation are discussed.

Jan 1, 1996

By Cory McElprang, Enamul Hoque, Aaron Thomas, Scott A. Jacobs

Crosshole Sonic Logging (CSL) only evaluates concrete on the inside of reinforcing cages leaving the outside unevaluated unless other types of testing are performed such as Perimeter Sonic Logging (PSL). While there have been some reports of PSL testing having accurately identified anomalies (e.g. Samtani et al 2005), experience by Case Foundation Company has indicated otherwise where false positives were determined with subsequent coring. Numerous cases of PSL false positives are presented as well as a study where a shaft was installed with both inside and outside tubes, and CSL and PSL data were compared. To date, there is very limited data published on perimeter sonic logging, or Gamma-Gamma Logging (GGL) with tubes on the exterior of drilled shafts. Several cases will be presented where false positives were experienced where PSL testing was performed. In addition, a direct comparison will also be presented where a shaft was installed with both tubes on the inside and outside where CSL and PSL data is compared. BRIEF HISTORY – CSL TESTING AND TUBES ON INSIDE The general procedure of Crosshole Sonic Logging (CSL) testing includes attaching tubes to the reinforcing cage to be able to send a transmitter in one tube and a receiver in another tube with which a sonic pulse is emitted from the transmitter and received in another tube. The time taken for the sonic pulse to travel between the tubes is measured and compared to expected values for the known distance between the tubes. Any increase in time from expected values indicates the sonic pulse traveled through a media other than homogeneous concrete such as objects in the path (spacer wheels, steel bracing, etc.), tube spacing, or soil inclusions. However, variations in arrival time can also result from differences in concrete density. The tubes have traditionally been placed on the interior of the reinforcing cage which protects them during hoisting and placement of the cage and reduces wave refraction caused by modulus of elasticity differences between steel and concrete. This allows the concrete within the interior of the reinforcing cage to be evaluated, but the concrete outside of the cage is excluded from traditional CSL testing. As a result, alternative integrity testing has been developed to not only provide different ways to evaluate the integrity of drilled shafts but to also address the issue of evaluating the concrete outside of the reinforcing cage. These alternative testing methods include Gamma-Gamma Logging (GGL), Thermal Integrity Profiling (TIP testing) and Perimeter Sonic Logging (PSL) which is similar to CSL testing but instead of the tubes placed inside the reinforcing cage, the tubes are placed on the outside of the reinforcing cage as shown in Fig. 1.

Jan 1, 2019

By Larry Gsellman

This report presents the results of a benefit/cost analysis of the Bureau of Mines' Coal Extraction RCD Program for the period FY 1977 through FY 1982. The analysis is an update of the analysis performed on the Coal Extraction R&D Program for EY 1975 - FY 1980 and presented in a MITRE report, MTR-7225, published in May 1975. Major changes included: new production scenarios and an update of R&D cost estimates.

Jan 1, 1977

In the wake of the financial crisis that affected world markets in 2002, there has been an increasing international focus on corporate governance. Various corporate governance codes of practice have been introduced, such as the Sarbanes-Oxley legislation in the USA, the Combined Code in the UK, and King III in South Africa. This focus on corporate governance has increased since the most recent financial crisis in 2008, the effects of which are still being felt world-wide. In the mining and minerals industry, reliable metal accounting is essential to sound corporate governance and is also becoming a focus of increased attention and concern, particularly as the figures generated by the metal accounting system feed directly into the financial accounts of mining companies. Mass measurement, sampling, and analysis provide the input data for the metal accounting system and sound corporate governance requires that the procedures used are based on best practice and that the data generated is accurate and handled correctly, transparently, and consistently to produce the accounting reports. The AMIRA Code of Practice for Metal Accounting has been widely adopted in the industry as a means to achieve this, and the compilers of the Code have conducted numerous metal accounting audits at operations, both in South Africa and abroad. These audits have shown that there is a real need for such a code of practice. Keywords metal accounting, AMIRA Code, corporate governance, risk management.

Jan 1, 2014

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936 and their rapid development have brought tine problem of brine disposal to the foreground in that State. The ultimate magnitude of the is not yet known, but already it is great enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field brines in Illinois and has studied in detail three subsurfaces disposal systems.]

Jan 1, 1940

By Niall Weatherstone

Introduction Risks & Rewards of a Mineral Reserve Life History of a Mineral Reserve Estimate Risk Assessment & Management Mineral Resource & Reserve Estimation Good Practice Mineral Resource & Reserve Reporting Conclusions

Jan 1, 2003

By R. J. Roman

The "mass balance" is unquestionably the most common class of problems for the process engineer'. Closely related, mathematically, is the "heat balance". Every laboratory test requires a mass balance to describe the results. Mass balance calculations can be subdivided into several sub-categories based on whether the results are time dependant or not and depending on whether the input data are measurements that contain errors or are hypothetical values with no errors. Time dependent mass balances are dynamic process simulations and in addition to the conservation of mass constraints require kinetic data input. They are one step beyond simple mass balances.

Jan 1, 1992

By P. D. Chamberlin

The interface between precious metal miners and gold refiners has been an uneasy interface over the years. The reasons for this interface and its apparent uneasiness and lack of trust include technical factors, economies of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates and sponge produced at the mine site are notoriously difficult to sample and a non-representative sample can be the cause of misunderstanding and distrust. Dore, however, is homogeneous and can be correctly sampled and analyzed. Second, the technology and chemistry of fine gold and silver production is complex and quite different from that of dore production. Most mining companies are content not to be involved with additional processing steps.

Jan 1, 1986

By Charles H. Wells

This paper presents a review of the state of the art in coal preparation plant instrumentation and a discussion of automation practice that could be applied based on current mineral beneficiation experience and demonstrated foreign technology in coal washing plants. Specific e-mules of applications of remotely controlled slurry values, pneumatic and electronic field transmitters, computers for control and data logging, and on-line analytical instrumentation are given. A program, to demonstrate this technology is described.

Jan 1, 1980

By Wayne D. Gould

The Cities Service Company's Pinto Valley mine and concentrator lie about 6 miles west of the town of Miami, Arizona at an elevation of approximately 4,000 feet above sea level. The concentrator started its first ballmill in July 74 and all six were available by November. Every effort was made to reduce capital costs, consequently, each unit process was studied critically to eliminate excess capital costs without loss of efficiency. Equipment selection was made on the basis of proven dependability and operating costs rather than on low bids. The result is a very workable plant with some important innovations. The concentrator is nominally 40,000 tons per day. The flowsheet is typical with 3 stage crushing, single stage closed circuit grinding, flotation, regrinding of rougher concentrate and cleaning of the rougher concentrate. The major equipment list is: 1 60 x 89 Traylor Primary Crusher 1 84" x 20' Stevens-Adamson Apron Feeder 3 7' x 16' Double Deck Tyler Screen 3 7' Nordberg Standard Crushers 6 8' x 20' Tyler Screens

Jan 1, 1975

By A. O. Apata, F. V. Adams

The use of rice husk ash as aggregate for foundry sand mould production has been studied. 5 –25wt% rice husk ash was added to the sand mixture. The chemical, physical and mechanical properties measured include: chemical analysis of the rice husk ash, particle size, density, permeability, compatibility mouldability, moisture content, green compression and shear strength, dry compression and shear strength. The result revealed that, addition of rice husk ash to River Niger Silica sand, increased the mouldability, compatibility, grain fineness number, both green and dry strength, slightly decreased the density, permeability and moisture content. The result shows that better properties is achievable by the addition of rice husk ash to River Niger silica sand and can be used to enhance the mould properties of foundry sand.

Mar 1, 2017

By K. T. Audt

The Yayoi period, from about 300 B.C. to A.O. 300, represents a time of important changes in Japanese history. During this period the advanced rice culture of the Asian continent was introduced to Japan, along with the techniques of animal husbandry, spinning, bronze casting and metal working(1) . As was the case in the Jomon period (11000 B.C. to 300 B.C.), the Yayoi period is traditionally defined by a particular type of pottery, characterized by the use of the potter's wheel and an extreme simplicity of decoration and form(2) . Pieces of this pottery were found in 1884 in a district of Tokyo, known as Yayoi-Cho, not far from Tokyo University. Within a decade the name Yayoi had come to be used for the period which also saw the first casting of metals in Japan121. During the Yayoi period, the foundation of the ancient Japanese state was laid as the individual small communities were unified and as labour specialization and social levels developed. In fact, the Yayoi may be the true ancestral culture of Japan(3) . However, the origin of the Yayoi is not definitely known. One theory indicates that the Yayoi people may have been driven from the Asian mainland (via Korea) by the dynastic wars that accompanied the unification of China under the Ch'in and Han and that these settlers rapidly displaced the Jomon. Bronze objects and the cultivation of rice may have arrived about the same time - in the third century B.C. Iron was in Japan within another century, but since it rusts badly and disintegrates, only a few small pieces are known from such an early date(4) . After about 50 B.C., the Yayoi cultures of western Japan were in fairly close and regular contact with the continent via Korea(5)

Jan 1, 1999

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By Robert Gannicott

??A mining company without the burden of operating a mine ??Management focused on marketing a high-quality, run-of-mine range of Canadian diamonds ??Robust revenue stream ??Specialist diamond knowledge ??Canadian exploration and development expertise ??BUT ??Single asset revenue base from depleting ore reserve ??Limited influence on production plans

Apr 1, 2005

By William B. Heroy

LOOKING back over the industrial and commercial progress of the United States during the last half century the outstanding influence has been the growth of the use of the fluid fuels, petroleum and natural gas. At the turn of the century these fuels supplied only 8 per cent of the energy requirements of the nation. Last year nearly 45 per cent of our heat and power supply were derived from these fuels. These figures are merely statistical reflections of the fundamental change in our national economy which has affected, in so many amazing ways, the life of this generation. The factors which have caused this change are still operative. The trend which has thus been established still continues and growth in the use of these fuels is, in all probability, still well below the peak, both for this country and for other parts of the world. Two great wars have not essentially changed this basic trend; if anything they have served to accelerate it. World War II did not alone increase our requirements for liquid fuels; it demonstrated the absolute essentially of petroleum resources to our national security. Petroleum is no longer just an important factor in our national standard of living; it is the most important single element in our national defence-

Jan 1, 1946

By Alexey T. Kovalev, Irina A. Khabarova, Valentine A. Chanturiya, Igor Zh. Bunin, Elizaveta V. Koporulina

"The paper presents new theoretical and experimental results about mechanisms of disintegration of mineral complexes and structural transformations of the sulfide surface under high-power nanosecond electromagnetic pulses (HPEMP). The heated gas outflow from nanosecond breakdown channels of sulfide minerals under HPEMP is considered. It is shown that the gas outflow from channels can be an additional destructive factor in the processes of the electric pulse discharge disintegration of mineral complexes. It is shown that the effect of HPEMP changes chemical surface composition and, respectively, technological properties of pyrrhotite and pentlandite. Morphology and elementary composition of new micro- and nanoformations on mineral surface of pentlandite and pyrrhotite have been investigated using up-to-date methods of SEM/EDX and Scanning Probe Microscopy. Preliminary electropulse effect on mineral products before flotation allows producing optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new nanophases and defects on the surface of sulfides.IntroductionThe effectiveness of High-Power Nanosecond Pulses in the disintegration and liberation of fine disseminated mineral complexes and the recovery of micro- and nanoparticles of precious metals from refractory ores was demonstrated in [1, 2]. Possible mechanisms of selective disintegration were considered in [1-3]. It has been shown both theoretically and experimentally that electric breakdowns can play an important role in the nanosecond pulsed treatment of milled minerals (e.g., semiconductor sulfides and quartz with particle sizes of 100 µm to 2-3 mm) that are carriers of finely disseminated gold and other valuable components. Electric discharges in such minerals are accompanied by a destruction of integrity in the form of breakdown channels and the formation of a system of cracks around these channels [3]. The development of the domains of induced cracks around the channels is determined by the pressure of evaporated material in the breakdown channel. Upon an instantaneous energy release in a channel (nanosecond discharges), the change in its transverse size and in the gas density and pressure in the channel is determined by (i) the radial motion of the evaporation wave, (ii) the radial expansion of the channel, and (iii) the heated gas outflow from the channel. The evaporation wave moves with a speed on the same order of magnitude as the speed of sound (or greater) and travels a distance of around the initial channel radius, i.e., a much smaller distance than the breakdown channel length."

Jan 1, 2011