Search Documents

By Z. Yanni, W. Xuan, Z. Jingyu, D. Jun

"In order to conserve the coal resources, many coal mines which have been mined begin to re-mine. Re-mining face is of complicated circumstances and coal spontaneous combustion is unknown, so experiments are designed to study the characteristics of multiple oxidized coal samples. The investigation into the oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. The non-caking coal is collected as coal samples. The raw coal sample with initial oxidation and the sample after second oxidation and third oxidation are obtained after a certain treatment of the coal. The temperature-programmed system, and proximate and ultimate analysis are adopted to compare the releases of gaseous products of spontaneous combustion characteristic parameters of the multiple oxidized coal sample. With the increase of oxidation times, experimental results indicate that the oxygen consumption rate, the release rate of carbon monoxide and the intensity of heat release are significantly decrease. The characteristic temperature dropped and the size of the pores in coal is smaller as well. INTRODUCTION China accounts for 13% of global coal resources [1-2]. In recent years, more and more coal mines begin to re-mine in order to conserve resources. This production mode is to mine coal pillar left by last exploitation or unavailable for mining. In the process of slicing mining for coal seam groups or thick coal seams, the second or multiple oxidation due to the mining-induced effect, may take place in the goaf of the lower seam. So the spontaneous combustion is prone to occur in this area. The study on oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. Scholars [3-7] have discussed the workability of re-mining for coal mines, verify the feasibility of the existing mining technology for re-mining area, and set up the prevention measures of coal spontaneous combustion. But all these measures are only based on on-site observation data, instead of experiment on spontaneous combustion characteristic parameters of re-mining coal samples which have a great importance for early prediction and forecast. The authors aim at investigating the multiple-oxidated coal spontaneous combustion law, and perfecting the coal spontaneous combustion mechanism to provide a basis for the prediction and forecast."

Jan 1, 2015

By Israel Liebman

The Bureau of Mines developed three types of passive water barriers for suppressing slow-moving coal dust explosions. One type is a modification of a conventional tub barrier and depends on the dynamic pressure generated ahead of an explosion to tilt the tub to release its water and suppress the explosion. The other two barriers operate in response to an increase in static pressure developed ahead of the explosion. Tests indicate the first barrier begins to release its water at air speeds as low as 50 ft/sec, and the second and third barriers will operate at a rise in static pressure as little as 0.5 psi. All three barriers were found to be effective in suppressing coal dust explosions propagating at speeds as low as 100 ft/sec. A plan is described for installing a water barrier in a working mine on a trial basis.

Jan 1, 1976

By A L. de Ambrosis, F M. Weir, M Fowler

Traditional kinematic and statistical analyses of geological structure for geotechnical engineering applications, while considered industry standard practice, have some limitations and unrealistic assumptions. An improved approach involves a discrete fracture network (DFN), a numerical model that explicitly represents how defects may be spatially distributed through the rock mass. The DFN technique utilises the structural data in stochastic analyses to give a range of possible models used for visualisation and stability analyses.The early development of the DFN approach was largely associated with modelling fractured hydrocarbon reservoirs and nuclear waste isolation programs. With recent improvements to computational power it has become recognised internationally as a valuable tool for modelling some geomechanical problems encountered when designing excavations in fractured rock masses. For tunnelling or slope stability projects DFN modelling provides visualisation of a rock mass and identification of likely failure mechanisms.This paper presents a suite of DFN modelling undertaken for the design of a tunnel within the Ashfield Shale unit of the Sydney Basin, Australia. The necessary input parameters and derivation of these, along with the importance of both an accurate engineering geology model and validation of the synthetic fracture network are demonstrated. Multiple realisations of the DFN were analysed to provide an indication of the number and volume of unstable blocks for the proposed tunnel geometry, enhancing support design. One fracture network realisation was sliced along multiple sections for use in finite element modelling.CITATION:Weir, F M, de Ambrosis, A L and Fowler, M, 2014. Discrete fracture network modelling for tunnel design in the Sydney Basin, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By W. M. Nabors

As part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers at the Morgantown (W. Va.) Petroleum Research Laboratory are studying secondary oil-recovery projects in the Appalachian region. The increasing demand for petroleum and its products and the increasing cost of exploratory drilling tend to emphasize the importance of improving the recovery of oil from known petroleum reserves. Published reports setting forth the pertinent facts of these operations may help others to profit by the experience. This report presents the results of a study of secondary-recovery methods used in West Virginia by the Piedmont Oil and Gas Co., the Ryan Oil Co., and Water floods , Inc., on their Roane County leases in the Walton and Clover Rush Run pools. The principal oil-producing horizon underlying the area studied is the Big Injun sand, at approximately 2,000 feet. The sand is often referred to as blanket sand because it underlies much of the State and is oil-productive in many localities. Most of the pools in the area were discovered during 1907 to 1910 and were similarly developed and operated.

Jan 1, 1960

By N. W. Bliss

"Bauxite has been the almost universal ore of aluminum for about 100 years, with most of the world's reserves oc¬curring in the developing countries. As a result of fiscal and political activities prompted in part by the energy crisis, the formation of the IBA combined with increasing freight and labour costs, these reserves are no longer as competitive or as secure as they once were. This has given fresh impetus to the development of processes for alumina production that utilize raw material other than bauxite. Canada has no bauxite and it is prudent to look for alter¬native raw materials within our own boundaries suitable for one of these processes.Of the three igneous rocks that have been used as a source of alumina, only anorthosite is considered as a potential source in Canada. The Al content would be extracted by a sinter process, which currently requires a raw material with a. minimum of 28% Al2O2. Thus, about 4 tons of anorthosite and 10 to 12 tons of limestone are needed to produce one ton of alumina. There are two petrologically distinct types of anorthosite, one containing the plagioclase andesine-labradorite and around 26% Al2O3, and the other containing upwards of 30% Al2O3, in by¬townite-anorthite; for our purposes they may be con¬sidered as low- and high-alumina anorthosite respectively. The high-alumina anorthosites are somewhat rare; the low-alumina anorthosites are much more common, partic¬ularly in Eastern Canada. Geologically speaking, there is no shortage of anorthosite in Canada. The reserves are im¬mense, although their low Al2O3 content coupled with con¬siderations of location, access and proximity to limestone could be constraints to their development. Fly ash from coal-fired thermal power stations and nepheline syenite can also be used in a sinter process, but neither is likely to be utilized in Canada in the immediate future.The H+ process utilizes an acid attack to leach Al from a raw material with at least 20% Al2O3. One of the best raw materials is kaolinite-bearing clay; not only is it high in Al, but most of it can be extracted. With the possible exception of the Whitemud clay in Saskatchewan, Canada is apparently deficient in clays with sufficient reserves to support an alumina plant utilizing the H+ process. Low-alumina clays with illite and montmorillonite may also prove to be a suitable raw material if advantageously sited with respect to industrial centers. The average shale con¬tains only 15% Al2O33, much of which may be contained in minerals, such as feldspar, not amenable to acid leaching. If shale is used as a source of alumina, it will be because it contains some other valuable commodity, such as oil or uranium, the extraction of which leaves the spent shale upgraded in extractable Al2O3 and lowers the over-all costs to a point where it is economic, Thus, rejects from coal washing plants are most commonly considered as a source of alumina; they are already mined, are available in large and ever increasing amounts, and may contain significant amounts of combustible material which upgrades the Al2O3, content of the resulting ash. Coal rejects from existing and developing coalfields in Alberta and British Columbia are a possible source of raw material, but present data indicate they may contain insufficient Al2O3."

Jan 1, 1976

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies.REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows:"

Jan 1, 2018

By A. Bowles

The process of accumulative roll bonding (ARB) has been applied to wrought magnesium alloy AZ31. Accumulative roll bonding results in severe plastic deformation of sheet material. In AZ31, this process leads to the refinement of the microstructure by dynamic recrystallization. The refinement of the microstructure results in an improvement in mechanical properties with potential for producing materials for superplastic forming. In this work AZ31 was bonded with up to 64 layers and the potential of roll cladding with aluminium was also investigated. The development of microstructure and the mechanical properties are reported here.

Jan 1, 2006

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By K. L. Kayler

The Bardon Trimount, Inc. stone quarry in Ashland, Massachusetts was the recent subject of a quarry closure review report. The quarry produces aggregate using standard drilling and blasting techniques. Stone is processed at an on-site plant. Noise monitoring data collected during the closure review indicate that the quarry generally operates within the quiet range. There is a decrease in noise while the quarry is not operating. Levels of dust associated with the quarry are low. Unpaved roadways are the greatest contributors of fugitive dust associated with the mining operation. The quarry cannot be seen from any homes within the town of Ashland, except during the winter months. The visual impact of the quarry on surrounding properties is minimal. Further quarry development is likely to reduce visibility of the quarry from some areas.

Jan 1, 1995

By M. R. Geer

Traditionally, fine coal is more troublesome than the coarser sizes at every step of the coal-preparation process--screening, cleaning, dewatering, and drying. Therefore the present trend toward a higher proportion of fines in the run-of-mine product, brought about by changes in mining practice necessitated to increase productivity, has added greatly to the task of preparing coal for the market. One of the more difficult and costly problems involved is that of recovering fine solids from the washery water. These fine solids should be recovered in the interest of conservation, and they must be removed to provide recirculating water of proper quality. If there is a plant effluent, it must meet increasingly stringent requirements against stream pollution. Vacuum filtration has been used for years at a few plants to recover the extreme fines, but its additional cost discouraged general adoption until recently. Now, with growing emphasis on better solids recovery, filtration is becoming more widespread. Many coal slurries filter readily, giving high cake rates and clean filtrates. Others, however, particularly those containing either a high proportion of material finer than 200-mesh or an appreciable amount of clay, are much more difficult to filter. Many of these refractory slurries can be rendered more filterable by flocculation. A previous report of Bureau of Mines research dealing with flocculation alone was published in 1940.5/

Jan 1, 1959

By K. A. Heasley

The objective of this paper is to back analyze the August 6th, 2007, collapse at the Crandall Canyon Mine in Utah, in order to better understand the geometric and geomechanical factors that contributed to that collapse. In this work, the LaModel boundary-element program, along with the best available information, is used for the back analysis. To initiate the analysis, a six-step base model of the mining in the Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters, rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis, a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) overall, the area was primed for a massive pillar collapse because of the large area of equal-size pillars, 2) the abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse and 3) from the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2010

By Jafar Safarian, Merete Tangstad, Leiv Kolbeinsen

"Silicon and its binary alloys have several applications in metallurgical, chemical, photovoltaic and semiconductor industries. Silicon goes to its liquid state within its production, refining and when it is alloyed with other elements. Therefore, the characterization of silicon melts thermodynamics is important and useful. The liquidus and activities in several silicon binary systems have been recently calculated by the application of two liquidus constants, which were established using the experimentally determined liquidus data. In the present study, the thermodynamic properties of six silicon binary melts, which are simple eutectics, are calculated by analytical approaches. In this case, the changes in the partial and integral Gibbs free energies and enthalpies of mixing are calculated and compared with the experimental data in literature. The enthalpies are calculated by two methods and the calculation results are compared to the data from the literature. It is shown that thermodynamic properties of silicon binary melts can be accurately predicted without the use of complicated thermodynamic software.IntroductionSilicon and its alloys have several industrial applications. Silicon is used for making aluminium-silicon alloys to produce cast parts, mainly for automotive industry. Silicon in the form of ferro-silicon is used to deoxidize and alloy steel and cast iron. The photovoltaic (PV) industry has had a rapid growth in the recent years and silicon is the dominant material used for the fabrication of solar cells. Silicon is primarily produced through carbothermic reduction of quartz in electric arc furnaces and the produced metallurgical grade silicon (MG-Si) contains around 1 wt% impurities. It is further refined to produce solar grade silicon (SoG-Si) with above 99.9999 wt% Si to fulfil the chemical requirement for PV application. Since molten silicon is processed all along the metallurgical route, obtaining fundamental thermodynamics knowledge about silicon melts is valuable for the related industries."

Jan 1, 2012

By X Hu, Z Pokrajcic, R Embry, P C. Stewart, J Carpenter, E Jones

Whilst the value of Pit to Plant and Mine to Mill optimisation has been proven since the 1990s, sustaining the productivity and efficiency gains typically requires ongoing test work, blast trials, plant surveys, and model calibration services. In contrast, the input to digital twin Pit to Plant or Mine to Mill optimisation is tens to hundreds of millions of tonnes of standard mine operating data. This paper presents a series of digital twin case studies from across the mine value chain, including machine learning testing methodology, model accuracy statistics and the application of Shapley Additive Explanations (SHAP) for model interpretation. These case studies demonstrate how machine learning and data fusion ore tracking connects hundreds of millions of tonnes of downstream performance data to produce digital twin models (operating models that are continuously updated and integrated into the wider Mine to Mill/Pit to Plant ore tracking system). Digital twin modelling software has been used to add block model variables for dig-rate, crusher and mill throughput, recovery (tailings grade), lump yield, product grade and product quality, fines yield and fines in lump. Block-by-block predictions are added to the geological resource and grade control block models as new block model variables. These new block model variables are used across all mine planning time horizons from life-of-mine planning to daily schedules. In addition to the materials handling and geometallurgical prediction case studies, the paper also presents digital twin case studies for drill and blast simulation and plant set point optimisation. The case studies show how digital twin simulation enables drill and blast engineers to simulate the effect of different blast designs in different blast domains using the mines operating data. Plant set point optimisation applies mathematical optimisation algorithms to the machine learning model to provide live operational decision support to metallurgists and plant operators. The digital twin machine learning case studies demonstrate a digital and sustainable paradigm for Mine to Mill and Pit to Plant optimisation.

Jun 22, 2022

By Ingvar Ymén, Anders Sandc, Jan Rosenkranzc, Lisa Malma, Ann-Sofi Kindstedt Danielssonb

The understanding of particle surface properties is essential for the study and evaluation of froth flotation phenomena, particularly in the investigation of various chemical or reagent effects. Dynamic Vapor Sorption (DVS) is a method used for the analysis of surface properties of powders for instance in the pharmaceutical industry. To the knowledge of the authors, it has however not been used before in applications related to mineral processing. The DVS technique involves measurement of the water uptake of a relatively small amount of sample as a function of the relative humidity (% RH) in a temperature-controlled environment. The purpose of this work was to evaluate the method and investigate how it can complement existing techniques for surface characterization in mineral processing. Four samples (feed, CuPb concentrate, Cu concentrate and Pb concentrate) from the Cu – Pb flotation process in the Garpenberg concentrator, Sweden, were analyzed by DVS and the traditional capillary absorption technique (Washburn capillary rise). This enabled comparison between the two methods and evaluation of their respective advantages and disadvantages. Both methods give the expected ranking of the hydrophobicity for CuPb concentrate, Cu concentrate and Pb concentrate, but a discrepancy was observed for the feed. Washburn gave a value for the contact angle which was in the same range as for the CuPb concentrate, whereas DVS gave a value for the moisture uptake which was much higher than for the CuPb concentrate. Thus, DVS ranks all samples correctly, but with an unexpectedly high value for the feed whereas Washburn gives good ranking for three samples out of four. Potential reasons for the discrepancies are discussed.

Jan 1, 2018

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson's discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 7 3/4 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612° F. (322° C.), they reduced the 7 3/4 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statement just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson's time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced consumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opinions advanced by different authorities in the scientific world to account for the apparent anomaly, but none,

Jan 1, 1877

By S. K. Ghosh

This paper discusses how the information on ash composition, ash-fusion temperatures, and ash-slag viscosity can be utilized to predict slagging and fouling potentials of a particular coal. A review of several empirical parameters which are commonly in use for determining such potentials is given. Also, some guideline values for interpreting the relative propensity of slagging and fouling of various types of coal are provided.

Jan 1, 1983

By W D. Rech, K W. Keskimaki

As an integral part of the conversion from rail haulage to conveyor haulage at Henderson, over six kilometres of drifting and several large complex openings were mined. The deepest of these areas was nearly two kilometres beneath the surface, bringing all of the challenges of rock stress and heat that come with mining at these depths. Though many mines operate at these depths, the development of the infrastructure necessary to support a 36 000 tonne per day caving operation brought some unique challenges to the development mining activity. The issues handled include: finding experienced staff for a æfast trackÆ development program; rock bursts and ground conditions; inflow of 50 degree centigrade water; acceleration of the project completion; large diameter raise boring and difficult muck handling.

Jan 1, 2000

In most mining operations the ore undergoes several processes such as drilling, blasting, loading, hauling, crushing, grinding and liberation to become the final salable product. Drilling and blasting is an important step in this process chain and itÆs results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. The value created per ton of broken ore is the difference between the price it commands when sold as the final product and the cost to produce it. Traditionally, the total process in the mining industry is classified into two groups as mining and milling. These are managed as separate cost centres inspite of the interdependency. Each process has a budget and production target and emphasis is usually on maximising production (tons) and minimising cost rather than the overall profitability of the whole business unit. The efficiency of each process is considered to be satisfactory as long as they are within budget and meet the production targets. The mine and mill managers usually try to optimise each process independently rather than the entire process. This paper discusses the potential pitfalls of decreasing the drilling and blasting cost per ton of broken rock without considering its impact on downstream processes. It introduces a holistic approach to blast optimisation by identifying and measuring the leverage that blast results have on different downstream processes and then optimising the blast design to achieve the results that maximise the overall profitability rather than just minimising the drilling and blasting costs. This paper demonstrates the benefits of such a holistic approach to blasting based on computer model simulations and field studies from metal and open cut coal mining.

Jan 1, 2001

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By Keith K. Griffiths

Computers are a valuable tool to the aggregate industry and should not be overlooked. The selection of proper mechanical components is necessary. Merely the addition of a computer to operate a mechanical system will not guarantee that the system will work. Material delivery by rail or truck for stock-piling and intra-plant material transfer can be accurately supervised by automation with simplified controls for the layman to use. There are mechanical problems that occur in material blending and load-out systems when such a system is automated. Such things as material flow, bridging, stockpiling methods, overloading of equipment and safety must be considered. How these problems can be overcome by proper selection of compatible mechanical and computer equipment will be discussed. Also, there are many individual material circuits in a plant that can be computerized at a nominal cost. This type of computer installation will not necessarily result in increased production, but it will produce greater efficiency in manpower. These small computers, binary counters, memory circuits and other devices and their application to the aggregate industry will also be presented. A careful evaluation of the mechanical and computer inter-relationship by someone understanding both "Rocks and Electronics" is essential to proper handling of material by computers. Computers for the mining industry may be either digital or analog computers. Unless the computer is to control some type of chemical process, such as a cement plant, the, analog computer is not required and the digital computer' will be quite adequate and less expensive.

Jan 1, 1967