Search Documents

Tapira Mine (Tapira, MG, Brazil) is the largest phosphate ore and concentrate producer in Brazil. The mine is an open pit, which until recently operated with a large equipment fleet and now uses a smaller fleet operated by contractors. The annual production reaches 17 Mt of ore plus 14 Mt of waste at a stripping ratio of 0.82. Defining the geological boundaries and forecasting the annual production can be a difficult task if not performed on a reliable model. The geological model has been totally reviewed as well as the estimation process. Ordinary Kriging has been used to build the new block model with P2O5 and contaminant grades. After estimation, block model validation and classification criteria definition to assess resources and reserves, the result is given by the life-of-mine plan is defined after pit optimisation and design. The Lerchs-Grossmann algorithm implemented in the NPV Scheduler was used to define the long-term production targets based on the main parameters P2O5 and the contaminants that are just important to the beneficiation process.

May 1, 2010

By Charles C. Mosher

An in-mine seismic technique for detecting faults has been tested in a Western U.S. coal mine. This technique has been used extensively in the U. K. to help guide longwall mining operations. Explosives detonated on the face of a seam generate sound waves which propagate into the seam. Reflections from faults are picked up by sensors on the same face. Computer processing is then used to determine the fault locations. A known fault was successfully located in this test. Modifications to the U. K. procedures were required for the relatively thicker roan and pillar mines common in the Western U. S.

Jan 1, 1983

By N. V. Mel'nikov

This paper discusses the reserves of oil, natural gas and coal in the USSR, with particular attention to the future role to be played by coal in supplying the energy fuel resources of the country.

Jan 1, 1972

By Mizraim Uriel Flores, Elia Guadalupe Palacios, Sayra Ordoñez, Iván Alejandro Reyes, Ister Mireles, Martín Reyes, Francisco Patiño, Hernán Islas, Víctor Hugo Flores

This paper presents the characterization of a sample of mercury jarosite that was synthesized by slowly adding Hg(NO3)2H2O into a Fe2(SO4)3nH2O solution. X-ray diffraction (XRD) analysis performed on the sample confirmed that the compound presents a crystal phase corresponding to mercury jarosite. Analysis through Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDS) determined that the precipitate is composed of mercury, sulfur, iron and oxygen. It is made up of spherical particles with an average size of 38 μm; these particles are made of rhombohedral micro-crystals with sizes ranging between 1 and 2 μm. Chemical characterization was performed through dichromatometry analysis, gravimetry and atomic absorption spectroscopy (AAS), thus obtaining the following composition: 27% Fe3+, 37% SO4 2− 14% Hg2+, 22% OH− + H3O+ + H2O. The following approximate formula of the compound was determined from chemical analysis: [Hg0.39(H3O)0.22]Fe2.71(SO4)2.17(OH)4.79 (H2O)2.09.

Mar 1, 2017

By J. L. Robson, C. M. Bristow

mass flow rates of particles and air (the loading ratio).

Dec 1, 1994

Discussion of the paper of W. H. Gunniss, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2309 to 2310. PROF. J. W. RICHARDS, South Bethlehem, Pa. :-In regard to the physical nature of quartz for making silica brick, is the coarse-grained preferable ? E. P. MATHEWSON, Anaconda, Mont. :-A dense quartz is preferable. The quartzite is the actual material used by the Anaconda Company. The sandstone referred to, the foreign quartz, was a very pure sandstone and bad hardly any impurities in it, and the brick made from that particular material, while apparently beautiful while coming out of the kiln, and true, immediately on heating in the furnace buffed up half an inch and were cracked open.

Jan 11, 1913

By A. V. Reddy, C. Beckermann

"The DC continuous casting of a grain refined AI-4.5%Cu round ingot with realistic boundary conditions is numerically simulated. Of particular interest are the effects of the transport of free solid in the form of equiaxed grains on the macro segregation patterns and the final grain size distribution. The study uses a previously developed two-phase model that incorporates descriptions of heat transfer, solute redistribution, melt convection, and solid transport on the system scale with microscopic models of solutal undercooling, microsegregation and grain impingement. The numerical results indicate that grain transport inhibits the formation of inverse segregation in the ingot shell and promotes negative centerline segregation. This is explained by the reduction in the solid coherency next to the mold and the advection of solute-lean grains towards the centerline. Comparisons with the experiments of Finn et al. [5] illustrate the need for considerable improvements in the model. IntroductionMacrosegregation continues to be one of the concerns in DC continuous casting of aluminum ingots. The variation in composition over the ingot cross section results in the need to adjust alloy composition in order to meet mechanical property specifications in finished products. The extent of macrosegregation is greatly affected by the casting conditions, such as casting speed, superheat, cooling rate, mold size, alloy composition, and grain refining practices. Thus, it is of great interest to develop a comprehensive mathematical model to simulate the casting process, enabling the selection of conditions that minimize macrosegregation while maintaining a high productivity."

Jan 1, 1994

By Emilia Visileanu, Eftalea Carpus

"Ecological economic policy shall be understood as the sum of political, economical and environmental measurements aimed at the entire economy dematerialization and the dematerialization shall be ""imposed"" since the designing stage of goods and services"". European textile and clothing industry with a long leading tradition in terms of innovation, fashion and creativity, continues to be one of Europe's major industrial sectors. Textile industry affects the environment by high consumption of water, energy and chemicals, as well as by the large amount of waste it generates as a result of using a large number of chemicals and technological processes.Textile waste prevention, reduction and ecological exploitation require the implementation of new management and education tools.Introduction“Europe must learn from the experience of global economic and financial crisis ""- this was the conclusion of the European Commission that has elaborated a ten-year strategy designed to reinvigorate the economy and make possible a growth which is ""intelligent, sustainable and favorable to inclusion"", by a better coordination of national and European policies.Adapting infrastructure and logistics that encourage the marketing of ""sustainable"", ""fair traded"" and ""green"" products as well as other special „green” products will facilitate the movement towards dematerialization and eco-efficiency among producers."

Jan 1, 2012

By Nadia H. Rafat, Iman S. El-Mahallawi, Hussein Badr, N. Khattab, Ahmed A. Abdel-Rehim

The basic part of solar water heaters is the collector and the main functional part of the collector is the absorber layer. In this work, a commercial locally available black painting (PACEN code 10382 colour 890), used for swimming pools solar heating, was modified by adding nano-graphite dispersion. The effect of nano-graphite particles percentage on the spectral absorbance of the material was examined on samples containing two values of 1.5 and 2.5% nano-graphite particles by weight. Fourier transform spectroscopy (FTIR) analysis was also used to identify the functional groups in the developed material. A simple experimental setup was designed to evaluate the performance of the developed nanodispersed selective coating polymeric based material, by measuring the increase in temperature of circulating water. It was shown that adding 1.5–2.5% nano-graphite particles to a polymer based black coating causes an increase in the optical absorptance, and an increase in the circulating water temperature.

Mar 1, 2018

By Sandeep Upadhya, Marc Morgan, Baljinder Bassi, James Fletcher, Mike Deevy, Nishant Nayan

"In order to protect public safety in the event of a deliberate fire attack, underground rail authorities are increasingly considering the need to design for arson-initiated fire scenarios. Where typical design fires for modern rolling stock mean a peak fire size is reached after 12 minutes, an arson-initiated fire reaches its peak within 2-3 minutes. We present the innovations required to successfully incorporate this requirement on a recent design-build project. In stations 3D modelling is used to optimise smoke reservoir designs, smoke chimneys, station boxes and tunnel geometry to allow coordination with structural requirements. In tunnels, novel coupling of one dimensional network modelling and 3D Computational Fluid Dynamics (CFD) is used to improve assessment of complex fire scenarios. Finally, the impact on tunnel structures is assessed through comparison with standard time-temperature curves and risk of explosive spalling. INTRODUCTION An increasing regulatory environment and the appreciable influence that terrorist incidents have had on public safety policy have motivated the need to protect against large arson fires, especially in civil structures and public transport systems. With a greater reliance of a growing urban population on underground subway systems, design of such infrastructure is continually being reassessed and developed worldwide. Underground rail authorities are paying increased consideration to the design of fires - with properties beyond the upper regions of growth and intensity - amongst arson fire studies. Use of fire hardened materials on modern rolling stock means fires caused accidentally can be expected to develop relative slowly. However, recent experiments involving large initiating fires (as would result from an arson attack) have shown rapid fire growth rates and flashover leading to greater maximum heat release rates, Hadjisophocleous (2012), White (2010), and Lönnermark, et al. (2015). This paper describes the challenges and innovations required to complete a detailed design to control smoke from such aggressive super-fast growing fires. Computational modelling is used to demonstrate the required smoke control design by configuring the mechanical exhaust system combined with careful coordination with the architectural and structural design. The design objectives are to provide tenable egress paths in accordance with NFPA 130 (2014) and fire-fighting access. Finally, analysis of the design fire is used to inform the tunnel lining design, reducing the risk of explosive spalling, protecting the asset in the event of a severe fire."

Jan 1, 2016

By W. V. Swarzenski

In its, effort to combat waterlogging and coil salinity, the later and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling and water sampling, since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline ground-water-zones in the Punjab Plain. Fresh ground water containing generally, less than 500 ppm (parts per million) of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh ground water extends to depths of 1,500 feet and more. Saline ground water occurs downgradient from sources of recharge, particularly in the lower central parts of the interfluvial areas and, presumably, underlies most of the Punjab Plain. The ground waters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters, near sources of recharge, to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in Dera Ismail Khan District sodium sulfate waters predominate. The pattern of distribution of saline ground-water zones and the observed gradual increase in mineral content, downgradient from sources of recharge, can be explained best by a hypothesis stressing the processes of evaporation from the water table and solution of minerals within the alluvial aquifer.

Jan 1, 1967

By C. Rutter, N. SHEA, K. KOLOBE

Henderson Mine’s primary production transitioned from the main portion of the 7700 level to the 7210 main panel in 2005. On the 7700 level, the southwest (SW) panel was brought into production in 2014 and produced through 2020. A-Panel was brought online in 2019 and took over primary production in 2020. The 7210 north panel is under development with production expected to commence in 2025. The 7700 northwest panel is expected to be the mine’s last production panel.

Previous methods for measuring the flow of solids in Jnrdraulic conveying have not considered the important effects of slip velocity and particle concentration. In this paper an extension of the method proposed byShirato et al. (J. Chem. Engng. 'Japan, 1: 164-167) for determining mass flow in a vertical conduit is outlined.The present method consists of measuring' the volumetric flow of the slurry (by a magnetic flow meter for instance) and the density of the slurry in two pipe sections of different diameters. Effects of variation of slip withparticle concentration, not previously considered, are allowed.Problems involved in estimating the density of a slurry from differential pressure measurement are discussed.The major problem is the uncertainties in estimating frictional losses due to the wall in two-phase flows. The greater reliability of a more "direct" technique, such as by 'Y-ray absorption, for measuring solid concentration is emphasized.

Jan 1, 1971

By E. T. Dumble

The history of the several petroleum deposits of Texas and Mexico, or of the sediments in which they now occur, if the deposits are not indigenous to such sediments, is known in a general way only, but it nevertheless casts strong light on the conditions surrounding them and is of great importance in the search for and exploitation of them. The petroleum deposits of Texas are separable into two main divisions: 1. The deposits of northwestern Texas, which are directly connected with the Oklahoma fields to the north, and have no representatives at all in the Mexican area. 2. The deposits of the coastal area, which extend into Louisiana on the east and connect with those of the Mexican coast to the south. Early in the Pennsylvanian period a series of bituminous shales and limestones were laid down over a broad area in Texas, Arkansas, and Oklahoma. These are known as the Bend series in Texas, the Caney shales in Oklahoma, and the Fayetteville beds in Arltansas. Following their deposition an uplift occurred, forming the Lampasas geanticlinal, which runs northeastward from the old Paleozoic land area of the Llano region toward Red River. The Bend series is petroliferous in places and has furnished a few producing wells on each side of the Lampasas uplift. This uplift forms the barrier and dividing line between the two divisions of the Texas petroleum deposits. To the west of it, in waters which were the southcrn extension of the interior continental seas, in connection with the sedimcnts and coal beds of the Pennsylvanian and Permian, great quantities of petroleum were deposited either as oil or as "potential petroleum." These sediments have been subject to very slight disturbance, and only very gentle folds are found, with no signs of volcanic action in any part of the area. The conditions, therefore, indicate that the greater part, if not all, of the oil in this area is indigenous to the beds in which it is found. East of the anticlinal the oldest beds which appear in contact with the Bend are the Trinity Sands of the Lower Cretaceous. No evidence has

Jan 1, 1916

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By T. T. Campbell

This report traces the development of techniques for the preparation of high-purity rare-earth metals. Rare-earth metals, excepting samarium, europium, and ytterbium, were prepared by converting their oxides to anhydrous chlorides or fluorides and reducing the rare-earth halides with active metals such as lithium or calcium. High-purity, anhydrous rare-earth chlorides were prepared by dissolving the rare-earth oxides in hydrochloric acid to form hydrated chlorides and by subsequently dehydrating the hydrated salts in the presence of ammonium chloride at temperatures ranging from 70° to 360° C. while under reduced pressure (50 microns to 1 inch Hg). The chlorides were also prepared by direct chlorination of rare-earth oxide-carbon mixtures. Reaction efficiencies in excess of 95 percent were obtained by either method; however, purer chlorides were prepared by the aqueous ammonium chloride conversion method. Purification of yttrium chloride by high-temperature vacuum distillation proved to be an effective method of separating, oxygen-bearing compounds from the chloride. Yttrium metal prepared from purified chloride contained significantly smaller amounts of oxygen (990 p.p.m. oxygen in yttrium metal prepared from raw chloride and 200 p.p.m. in that prepared from distilled chloride).

Jan 1, 1961

By Christine E. Turner-Peterson

Pore-filling organic material concentrated uranium to form sandstone-hosted primary uranium deposits in the Jurassic Morrison Formation of the Grants uranium region, New Mexico. Petrographic observations and radiometric ages for primary ore in the Westwater Canyon Member require that the organic material was emplaced early in the diagenetic history of the host sandstone; in fact, organic material was emplaced before major compaction. This inferred early emplacement constrains models concerning the nature and origin of the organic material and thus also constrains models of ore genesis. Reconstruction of the burial history of the basin indicates that Late Jurassic-Early Cretaceous time, the interval of inferred emplacement of the organic material, was probably not a time of hydrocarbon generation and migration. Nuclear magnetic resonance analyses, elemental abundances, and isotopic studies provide further constraints on the nature of the organic material, and data from these studies are consistent with a humic acid rather than an oil origin. In addition, the overall tabular shape of primary uranium orebodies and the way these orebodies are suspended in the host sandstone mimics Recent deposits of humate, the precipitated form of humic acids. The critical clue that favors a humic acid origin for ore-related organic material is provided by the nature and patterns of postdepositional alterations that are spatially and temporally related to primary ore, specifically destruction of detrital magnetite and ilmenite (iron-titanium oxide) grains. Humic acids are implicated in the destruction of iron-titanium oxide grains because these organic acids are one of the most effective natural agents in leaching of Iron from these grains. Thus, timing constraints, chemical evidence, orebody geometry, and the nature and patterns of ore-related alterations favor a humic acid origin and suggest that an oil origin is highly unlikely. Because alteration of iron-titanium oxide grains tracks the pathways of humic-bearing solutions through the host sandstones, it is possible to trace these solutions back to their source. Alteration patterns in the Westwater Canyon Member suggest that the humic-bearing solutions originated as pore fluids in the mudflat facies of the overlying Brushy Basin Member and moved into adjacent sandstones during early dewatering of the mudstones. The humic acids precipitated, by the process of cation loading, in tabular layers. Uranium was concentrated within these tabular layers by complexation with the humic acids to form primary uranium orebodies.

Jan 1, 2013

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By W. C. Patrick

The Spent Fuel Test-Climax (SFT-C) was con- ducted to evaluate the feasibility of retrievable deep geologic storage of commercially generated spent nuclear-reactor fuel assemblies. One of the primary aspects of the test was to measure the thermomechanical response of the rock mass to the extensive heating of a large volume of rock. Instrumentation was emplaced to measure stress changes, relative motion of the rock mass, and tunnel closures during three year of heating from thermally decaying heat sources, followed by a six month cooldown period. The calculations reported here were performed using the best available input parameters, thermal and mechanical properties, and power levels which were directly measured or inferred from measurements made during the test. This report documents the results of these calculations and compares the results with selected measurements made during heating and cooling of the SFT-C.

Jan 1, 1986

By Yifei Zhang, Jianzhong Li, Wenhao Zhang

Eletrochemical behavior and corrosion properties of a Ti–6Al–4V alloy fabricated by selective laser melting in artificial seawater at temperature ranges from 20 to 40 °C were investigated using electrochemical techniques, including potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and Mott-Schottky measurement, etc. Equivalent circuits were simulated to investigate alloy surface and analytic effects of temperature on interface of alloy and solution. The results showed that corrosion potential increased with temperature rise, and the EIS presented a single capacitive resistance characteristics. When the temperature reached 35 °C or above, passive current increased, while the passivation phenomenon was not obvious and corresponding radiating arc radius reduced, indicating that the resistance decreased, conductivity of surface passivation film improved, and corrosion performance improved. According to the Mott-Schottky curves, alloys exhibited n-type semiconductor characteristics. With increasing temperature, conductivity of passivation film enhanced, and alloy corrosion resistance decreased. At 40 °C, alloy possessed the worst corrosion resistance.

Mar 1, 2018