Search Documents

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By D. F. Lillie

The milling plant of Bicroft Uranium Mines Limited has been in operation for a period of 2 years. During this time many changes, both physical and chemical, have been made in an effort to improve plant efficiency. Investigational work has been facilitated greatly by the fact that the Bicroft mill consists to a large extent of two parallel circuits; however, the number of inter-related variables is great, and it is difficult to measure, let alone control, all of them simultaneously. The Bicroft mill staff feel that much progress has been made, but there is much yet to be done and many questions still to be answered. The property of Bicroft Uranium Mines is located in Cardiff Township in the Highlands of Haliburton County, southeastern Ontario, some 140 miles northeast of the city of Toronto and 70 miles due north of Lake Ontario. The ore-bearing dikes are classed as mafic, non-segregated, syenite and granite pegmatites. Microline, microline perthite, quartz, uraninite, uranotharite, fluorite, titanite, cyrolite, calcite, pyrite, pyrrhotite and molybdenite as important accessories. The mill was designed for a nominal capacity of 1,000 tpd with all sections except grinding, leaching and clarification capable of 1,500 tons. Feed was entered to one mill unit on October 29, 1956 and to the second parallel line on November 13. The total feed rate was at 1,000 tpd on November 15. The first precipitate was produced on November 12. By August 1958 the average entry had been increased to 1,410 tpd without the installation of any additional major equipment. The overall recovery has been greater than 93,0 pet do several months, but a recovery of 92.5 pct appears to be most economical. Operating time for 8 months in 1958 has been 97.1 pet although all grinding mills were relined during this period.

Jan 1, 1959

By R J. Holmes

An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and traded is crucial to effective resource utilisation, plant design, process optimisation and finally quality control to ensure that contract specifications are met. However, all too often the responsibility for sampling is entrusted to managers and personnel who do not fully appreciate the significance and importance of collecting representative samples for analysis, and everyone seems satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. This needs to change, because there is little point in accurately analysing samples if they are not representative in the first place. The resultant analyses can be next to meaningless and the effort taken to analyse such samples is to a large extent a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts. It is high time that sampling is given the attention it deserves as the first critical step in the quality measurement chain.CITATION:Holmes, R J, 2013. The importance of sampling in the mineral industry, in Proceedings MetPlant 2013 , pp 34-49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988

By B. J. Moore

This publication contains routine analyses and related source data for 547 natural gas samples from 22 States and three foreign countries. Of this total, 340 samples were collected during calendar year 1967. The remaining 207 analyses are of samples collected during previous years, but releases granting, permission to publish the results were not received until 1967. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. The Bureau of Mines has conducted this survey in the United States since 1917, and in 1965 it was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 516.4 Nine previous publications have been made to present results of 7,618 gas analyses made by the Bureau of Mines Helium Activity prior to 1967. The first three, Bulletins 486,5 576,6 and 6177 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other six

Jan 1, 1968

By A. A. Novoselov, U. Kelm

"Large volumes of mine tailings accumulated in surroundings of porphyry copper deposits represent a growing threat to environment. They contain significant concentrations of toxic metal and metalloids which can contaminate river runoff, ground waters or can be transported by wind. Both extreme pH of fluids in tailings impoundments and high surface areas of processed mineral grains provide their increased reactivity. As a result, during only a few decades, As, Cu, and Mo can be mobilized, redistributed through the tailing column and accumulated through post-deposition leaching, evaporation and contamination with natural fluids. Those processes are reflected in the forming of secondary minerals. Gypsum, Fe oxides/hydroxides, efflorescent salts and clay minerals are typical alteration products in tailings. Here we present the results of reactive transport simulations implemented on the base of PHREEQC and SUTRA codes. The one-dimension model emulates the mass balance between rainfall, evaporation and subsurface runoff, the kinetically- and thermodynamically-driven dissolution of tailing minerals, advective and diffusive transport of tailing fluids, and precipitation of secondary phases. A typical tailing column is composed of four unequal layers with predominance of (i) evaporation, (ii) secondary mineralization above, (iii) below water table, and (iv) near the bottom of dump. Those horizons are characterized by contrasting pH, chemical composition and bulk mineralization of pore fluids, distinct accessibility of atmospheric oxygen and, as a consequence, distinct intensity of sulfide oxidation. The modeling and its verification on Chilean tailings impoundments reveal the complexity and high rates of secondary mineralization. The accumulation of toxic alteration products is controlled by fluid transport through the tailing column induced by both rainfall/evaporation and exchange with subsurface runoff. The geochemical modeling is a powerful approach which allows comparing the processes in tailing deposits produced by distinct flotation regimes and providing the long-term predictions of their environmental impact as well as identifying sectors of tailings for possible re-processing."

Jan 1, 2018

By F. Molhem, S. Banisi, H. R. Montazari, E. Arghavani, Gh. R. Biniyaz, Gh. A. Parsapour

"Water plays a key role in mineral processing plants and to process one ton of ore 2.5 ton water is needed. Thickeners are commonly used for dewatering and recovering water in most processing plants. The underflow pulp density is increased by sedimentation of particles and clear water is recovered from the overflow. One of the issues related with using the process water is the presence of suspended fine particles in the clear overflow water which can create blockage in transfer pipes. The froth formed on top of thickeners is the main cause of this problem. In this study, a method to decrease the froth formed on the Sarcheshmeh Cu-Mo thickener surface was introduced and implemented. At the first stage, the old punched plate feedwell was removed and it was replaced by a vane type feedwell. A spray water ring using fish-tail type nozzles was then installed to break froth layers by water. These modifications led to 63% relative reduction in the water turbidity, 11% relative increase in the underflow solids concentration, 20% relative reduction in torque, 19% relative reduction in its standard deviation and an increase of 6% in water recovery.INTRODUCTION The Sarcheshmeh copper complex, the largest copper producer in Iran, located in southern Iran. In the processing plants of this complex, over 250,000 m3 of water is consumed daily. Because of a lack of water in this area and very low yearly rain fall (150 mm), water plays a vital role in the complex. As a result, it is then aimed at maximum water recovery by taking all necessary measures. The recycled water in order to be used should not contain any suspended solids indicated by low turbidity."

Jan 1, 2018

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By D. de la Villa

From 1989 to 1992 Rio Tinto Minera has developed and implemented a productivity program in its Huelva Plant, including Smelter, Acid Plant and Electrorefinery. This Plan was designed in order to increase productivity, reduce emissions and produce a better quality of cathodes. This paper describes investments and operating improvements involved in this project, focusing on Smelter and Acid Plants, and comments the results obtained so far.

Jan 1, 1993

By George J. Young

The nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker's stand-point has also received much comment, arid scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of niore intensive study and experimeritation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has been written concerning an accurate definition of the term "slime," but no comprehensive definition seems to be gcnerally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may bc and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles niuch more slowly and finally a certain portion remains

Jan 1, 1912

By G. Akdogan, S. M. Bradshaw, M. I. Isaacs, P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached in order to remove base metals from a concentrate containing platinum group metals (PGMs). This paper investigates the atmospheric leaching process, in order to develop a better understanding of the leaching behaviour of the base metals; in particular Cu, Fe, Ni, and the PGMs in particular Ru and Ir with key process variables, acid concentration, copper concentration under oxidative leaching conditions. Higher initial acid concentration resulted in a higher copper, iron and nickel extractions, as well as higher leaching rates together with faster Cu, Ru, Ir precipitation occurring. On the other hand, a higher initial copper concentration resulted in more nickel but less iron being extracted. Keywords: PGM, converter matte, leaching, precipitation

Jan 1, 2020

By A Batnasan

The main techniques for removing phosphorus as an impurity element in iron ores are physical separation (eg magnetic separation, flotation) and chemical separation (acid leaching, alkaline leaching and bioleaching) processes. When phosphorus occurs in iron ores as phosphate minerals (eg apatite), physical separation techniques are available to remove the gangue minerals from iron ores. On the other hand, chemical separation techniques are suitable for reducing phosphorus levels when phosphorus is associated with iron oxides and hydroxide minerals (eg hematite and goethite) in iron ores. In this study, the dephosphorisation behaviour of high‐phosphorus iron ore was investigated using a combined alkaline roasting and water washing route. Roasting experiments were conducted in a laboratory electric muffle furnace using various concentrations of sodium hydroxide (0–50 g/kg-ore) at different temperatures (100–800°C), varying prolonged roasting times (0–2 h), and different particle size fractions (-45 – -250 μm) of iron ore. Subsequent water washing experiments were employed at various pulp densities (30–1000 g/L) and different times (30 s – 60 min) at ambient temperature. Hematite and goethite were the main minerals in the high-phosphorus iron ore identified using X-ray diffraction (XRD) analysis. The iron ore assaying 63.40 mass % Fe (total), 0.240 mass % P, 4.53 mass % SiO2, and 4.87 mass % Al2O3 were determined using X-ray fluorescence (XRF) analysis. The results showed that the dephosphorisation rate of the iron ore was reached 40 per cent under roasting with 50 g/kg-ore NaOH at 300°C for 2 hours followed by water washing for 30 s with a pulp density of 300 g/L, reducing phosphorus level from 0.240 mass % to 0.142 mass %. At the same time, the iron grade was reduced from 63.4 per cent to 59.5 per cent, caused by an iron loss. Results suggest that the phase transformation of goethite induces the dephosphorisation of high-phosphorus iron ore under alkaline roasting conditions

Aug 22, 2022

By W. W. Agey

As a result of a field examination made during the Bureau of Mines intensive manganese program, three lots of ore were procured from the famous old Paymaster District, 7 miles from Midway Wells, Imperial County, Calif. This district is an old producer and shipped approximately 10,000 tons of 45-percent manganese ore during World War I. A 2-ton lot of ore was taken of a Bureau engineer from the exposure of a small fissure vein in conglomerate on the Turtle Group of claims; 1 mile east of the Pacific Coast Manganese Corp. claims. The vein material consisted of manganese oxides, calcite, and quartz in fairly coarse association.

Jan 1, 1949

By F. Harold Weber

On July 13, 1967 the San Bernardino County Planning Commission approved publicly a request by American Smelting and Refining Company for a zone variance to conduct a silver mining and milling operation in the Calico district, southern California, Coincidentally, on July 14 the U.S. Treasury halted its sales of silver, and the U.S. free market price quoted rose immediately from $1.30 to $1.77 per ounce. In its request to the commission Asarco stated that about 13,500 to 15,000 tons of rock would be moved daily by surface mining, including 7,000 tons of ore. The ore would be crushed to minus three-quarters inches and the silver recovered "by a chemical process." The grade of the ore was not given, but the company said that it might also recover barite as a byproduct, The operation would employ 150-160 people. Additional activity in the district includes exploration programs by Superior Oil Company and Calico Silver Mines, Ltd. History and production: In retrospect, as the price of silver began to rise in 1961 from 91 cents an ounce, and as Asarco began its exploration program in late 1964, a new era for an old bonanza silver district would seem to have begun. The Calico district has been mined for silver only on a very, very small scale since 1882 to 1896, when an estimated $12 to $20 million (perhaps 15 to 20 million troy ounces) of that metal was produced from the 50-odd mines of the district and vicinity. These mines include the Silver King, Oriental, Waterloo, Garfield, Odessa and Waterman (which is about 8 miles west of the district). Much smaller-valued amounts of barite, gold, lead, and copper also have been produced from the ore deposits of the district; and from 1884 to 1907 the region yielded about $9 million worth of borate minerals.

Jan 1, 1967

By John Richards

MY remarks will be confined to the experience of our company in mining the No. 8 seam of coal in Ohio, although I believe that the relationship existing here between the method of mining and the method of cleaning will hold true in many of the coal seams throughout the country. The increasing demand for a cleaner and better graded product is being felt throughout the entire coal industry, and the methods of mining are playing an important part in the control of various sizes and quality of coal produced. We have found a definite relation between the mechanical loading of coal and its preparation for the market. In the No. 8 coal seam the location of the non-combustible material is regular. The' marketable coal lies in three benches, separated by streaks or bands of impurities. These impurities must be removed from the coal to properly pre pare the product for the market. Where hand-loading methods are employed, the loader removes as much of this non-combustible material as possible at the working face. The impurities that are missed by the loaders are removed as the coal passes through the preparation plant, by means of picking tables. As this method of cleaning cannot improve the quality of the extremely fine sizes, a practice has been established in the company's hand-loading mines, of undercutting the coal about 2 in. above the bottom of the seam, thereby eliminating any possibility of impurities caused by the cutting machines cutting into the rock bottom below the coal seam.

Jan 1, 1934

By D. S. Davies

Further development of the Nitric-Sulfuric Leach (NSL) process has led to an improved design of the leach and nitric acid recovery steps. NO produced in the leach step is reacted with oxygen, regenerating N02, which is sparged directly into the leach reactor. Leaching is simplified to two steps and the nitric acid plant is replaced with an oxidation recycle gas sys-tem. Laboratory work substantiated the concept and led to selection of operating conditions. The lab work also pointed to improved process control compared to use of nitric acid as the sole oxidant. Recovery of copper from purified pregnant liquor is modified to use air agitation electrowinning improving cathode quality and lowering tankhouse costs. Economic evaluation shows reduction of capital requirements from $2400/AT to $2000/AT in 1978 dollars for 50,000 TPY of copper production.

Jan 1, 1978

By R. D. Lopez

The concept of "heat recuperation" for the grate-kiln pelletizing system was first implemented at the Sydvaranger plant in Norway in 1974. Essentially, heat recuperation involves bringing hot air from the second stage of the pellet cooler to the drying zone to increase drying-air temperature to the maximum limit. 'Burner-fuel savings result from a lower kiln secondary-air mass flow at a higher temperature. Because of the fuel benefits achieved at Sydvaranger, heat recuperation has been included innumerous new grate-kiln plants built since then, and some older plants have been retrofitted for heat recuperation. In recent years there has been much confusion about the fuel benefits of heat recuperation. To answer some of the questions, a mathematical model was developed and plant tests were conducted at Minntac Phase 111. Minntac is a magnetite taconite concentrating and pelletizing plant, and Phase III has two indurating lines. This paper presents the results of the studies and plant tests.

Jan 1, 1980

By l. Bokányi

The Tóth adsorption isotherm-model was derived and has been widely used for the inhomogeneous solid surfaces. The three-parameter isotherm incorporates the effect of the interaction between the adsorbed substances as well. All classic isotherms can be clearly derived from this one. Bio sorption is the sequestering of dissolved components, i.e. metals from aqueous environment by living or dead biomass. The mechanism of the bio sorption is rather complex and predominantly refers to the affinity of the chemical functional groups: acetoamido groups of chitin, structural polysaccharides, amino and phosphate groups in nucleic acids, amino, amido sulfhydryl and carboxyl groups in proteins, hydroxyls in polysaccharides, sulphates, etc. towards the soluted substances, i.e. heavy metal ions. The physisorption, as well as the micro precipitation also play a role in the bio sorption mechanism. The description of such a complex process can be done by a model reflecting this complexity. According to our experimental results obtained using algae and immobilised algae for the sorption of heavy metal cations, the most appropriate model for such a description is the Tóth-isotherm, the parameters of which can be interpreted. Flotation process is also a very complex one, the overall result of which depends on the partial results of many micro processes and parameters. The particle interaction which very often takes place in the flotation systems makes the phenomenon even more complex. The flotation kinetic model with particle interaction was already introduced by author in 1994 and further developed in 2000. In this paper based on the experimental results obtained with metallic particles in case of recycling flotation the applicability of the Tóth-equation as an alternative flotation kinetic model for the systems with particle interaction is proved. The applicability of Tóth-model in mineral processing demonstrates again its universal character and the great talent of the late József Tóth, great Hungarian chemist. Keywords : Toth isotherm, biosorption, Langmuir, Freundlich

Sep 1, 2012

By John C. Nixon

In 1959, The Australasian Institute of Mining and Metallurgy (Aus. I.M.M.) was asked by the Federal Government of Australia and the State Government of South Australia to join in the formation and management of a new contract research organization which was subsequently named The Australian Mineral Development Laboratories (Arndel) ? This body was formerly the Research and Development Branch of the South Australian Department of Mines which had been set up to develop the Radium Hill uranium deposit. It had then gone into contract R&D and the State felt that it would be more appropriate for the Branch to become a separate national organization. The Aus. I.M.M. decided that a professional institute could not participate directly in Arndel and, as there was no other suitable industry group to do so, it formed the. Australian Mineral Industries Research Association Limited (AMIRA). AMIRA held its first Annual General Meeting in September 1959 when the first Council was elected and the Memorandum and Articles of Association were adopted. The initial task of AMIRA was to raise guarantees of work or cash from its members to underwrite Arndel for the first five years of operation. The Federal and State Governments also provided guarantees and Arndel commenced operations in January 1960.

Jan 1, 1977