Search Documents

By Tapio Ahokainen

Commercial modeling software and increasingly efficient computers enable today computational fluid dynamics (CFD) to be used as a tool for a more comprehensive understanding of the flash smelting and flash converting processes. CFD modeling can be used for design purposes in many technological areas, but some relevant physical and chemical phenomena are still missing in the commercial CFD solver packages. Therefore, Outokumpu has developed several subroutines for solvers to describe analytically the phenomena in the flash smelting environment. CFD sub-models of the copper concentrate and matte combustion, the particle-particle-wall interactions and for more accurate radiation properties of the gas-particle suspension are needed to ensure reliability of numerical simulations on the flash smelting and converting vessels. Several basic combustion phenomena can be modeled with a number of commercial solver packages, but own models for combustion must be included in the case of sulfides as the feed. Mathematical models for copper concentrate and solid matte combustion have been developed during the last decade. They calculate compositions of the particles and temperature, based on extensive experimental research work in laboratory scale furnaces with validated kinetic parameters and temperature measurements of reacting particles. Inside and near the concentrate burner, the standard particle tracking methods do not include the particle-particle interactions and the particle-wall interaction is too much simplified to describe properly the particle collisions with the distribution cone. Therefore, additional models for the particle-particle as well as particle-wall interactions have been written and implemented. For thermal radiation, models for the emissivity of a gas mixture and for calculating the particle absorption and scattering coefficients have been developed and tested. In addition, the advanced radiation model can be used i.e. in the enhanced simulation of off-gas cooling in the heat recovery boiler area of the flash smelter.

Jan 1, 2006

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Bucknell WR, Clarke DE

The paper provides a company's view of the relative merits of various valuation methods and outlines the basic approach it takes to the valuation of an exploration property. The negotiating process and methods of acquiring an interest in an exploration property is discussed The valuation methods discussed are: 1. Exploration Expenditure. 2. Real Estate. 3. Joint Venture Terms. 4. Rule of Thumb. 5. Net Present Value - Discounted Cash Flow. 6. Geoengineering.

Jan 1, 1994

By A. B. Hooker

All State mining laws require that flame safety lamps be used in gassy mines; the laws of some States require that safety lamps be kept for emergencies at every coal mine, whether gassy or nongassy. The use of the flame safety lamp has been widespread because it is the only defice readily available for detecting both the presence of methane and deficiency of oxygen. This paper reports the results of an investigation by the Electrical Section, in cooperation with the Gas Section, of the Pittsburgh Experiment Sta¬tion relative to the behavior of permissible flame safety lamps in mine atmospheres deficient in oxygen and the effects of methane5 on the detection of Oxygen deficiency.

Jan 1, 1937

By J. Kou

In this paper the activation behavior of quartz using Ca(OH)2 as an activator in quartz reverse flotation with anionic collector was evaluated and their adsorption behavior was investigated using a variety of techniques. The adsorption of the collector KS-I on the surface of quartz with and without Ca2+ was primarily characterized using Quartz Crystal Microbalance with Dissipation technique (QCM-D), which is a high sensitivity in-situ surface characterization technique. The flotation performance was evaluated using a laboratory mechanical flotation cell at different process parameters such as pH, collector dosage, and Ca(OH)2 dosage. The anionic collector evaluated was a commercial fatty acid KS-I. The QCM-D data showed that the collector adsorbed on quartz more readily with Ca2+ as activator. The mass and structural property of the collector layer adsorbed on quartz surface at 2.16×10-3 mol/L of Ca2+, 0.3 g/L of collector and pH 12.0 have been studied using the technique of QCM-D. The chemisorption of the collector KS-I on the surface of quartz in presence of Ca2+ were also demonstrated by means of zeta potential, QCM-D and FTIR analysis.

Feb 23, 2014

By Ed Billington, Mike Shields

The trail blaster is faced with a wide range of workrelated challenges, not the least being the work setting itself. It is usually remote, being anywhere from 5 to 30 or more miles (8 to 50 km) from any road. It may be in mountains, high rock desert, or coastal rain forest, and can range from sea level to over 12,000 feet (3700 m) in elevation. The blaster may be part of a 2-person clearing crew, a 4-person maintenance crew, or a 10-person construction crew. The crew will usually be mobile, moving and working up to 10 miles (16 km) or more per day, relying mostly on their own backpacks to move camp, tools and supplies from site to site. Periodic resupply may be by helicopter, aird rop, or even “sherpa” groups, but most often will be by packstrings of horses and mules. The crew goes into the backcountry a n y w h e re from two weeks to three months at a time, and while there, its members “live the job” 24 hours a day, enjoying baking heat, torrential rain or mid-July s n o w s t o rms along with the truly glorious weather that c o m p e n s a t e s . So who is this blaster? Well, “he” may be she, since some of the top trail blasters are women. He/she will also be more than a blaster: Crews are small, so experienced members must be capable of handling the full range of trail work. Thus this blaster is also a driller, and usually also a bucker, snag faller, rigger, dry-stone mason, log and timber carpenter, bridge builder, mule p a c k e r, small-engine mechanic and, not least, camp cook capable of putting out a hot meal from a campfire , in a downpour, in the dark. Being in remote locations, often without reliable communication to the outside world, trail crews enjoy a remarkable degree of independence from “supervision.” With that comes the responsibility to make sound decisions which expedite the work, while promoting crew safety and welfare .

Jan 1, 2004

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By S. Makni, A. Faucher, F. Robichaud, A. Bouajila

"Optimizing the ball charge in a grinding mill may be needed to maximise throughput or alternatively, to achieve proper product size in more challenging situations. Efforts to optimise the ball charge however are essentially empirical and suffer from the lack of appropriate, accessible and reliable tools. To address these limitations, a new model-based technology was developed that relies on 3D Discrete Element Method and population balance techniques: it takes on the form of a simulator that aims to significantly decrease the time required to optimise the size distribution and the grinding media load within a ball mill. This paper summarizes the research work related to the development of this simulator. The calibration of the different constituting sub-models will be highlighted. The successful use of the simulator to predict the effect of ball make-up on the grinding product size distribution in one plant is also reported.INTRODUCTION Adjusting the characteristics of the grinding media charge in grinding mills holds significant potential for optimisation of mill performance. For example, properly adjusting the ball size distribution in a ball mill can help achieving specified targets for final product size distribution and/or throughput capacity. However, several problems appear when reviewing the process and the available tools to optimise ball mill load: • The current empirical simulation tools are lacking with regard to the ability to predict the performance of grinding when changes to mill ball make-up are made; • Generally, these tools estimate the top size of the charge so it is difficult to predict the effect of mixed ball make-up; • As the quality of prediction of these tools is low, the operators try to optimise the ball charge by a ""trial and error"" method and proceeding with conservative changes. The influence of these changes on grinding performance is often less than the measurement precision and the improvements then remain imperceptible; • A change in ball make-up may require an average of about 6 months waiting period before reaching the stationary state of mill ball load. This exercise is due to be costly if applied change decreases the mill performance. In its effort towards the comminution process optimisation, COREM R&D portfolio had addressed the herein described opportunity during the last five years This paper describes the technology already developed for the optimisation of ball charge. It takes on the form of a simulator that aims to predict the evolution of the grinding media load, the grinding energy available in the ball mill and the final product size distribution. The simulator was first validated in a pilot scale ball mill and then applied in an industrial case."

Jan 1, 2012

By Christopher Mark, Anthony T. Iannacchione

Falls of ground continue to be one of the most serious causes of injury to U.S. miners. Of the 256 fatal injuries that occurred in mining between 1996 and 1998, 52 (20%) were caused by falls of ground (Table I). Falls of ground affect some sectors of the mining industry more severely than others. For instance, nearly 40% of the 98 coal mine fatalities between 1996 and 1998 were caused by falls of ground. Underground miners are at much greater risk than surface miners. Nearly half (45 out of 101) of underground mine fatalities were attributed to roof, rib and face falls, while less than 5% of the 155 surface fatalities were caused by falls of highwalls or slopes. Sources of Data All of the injury data examined in this study were derived from MSHA’s Fatal Investigation Reports (www.msha.gov)and the MSHA accident database. Because falls of ground often result in serious injury, MSHA Fatal Alert Bulletins and Fatal Investigation Reports provide a useful snapshot of ground control issues in the mining industry. MSHA requires that mines file a report on every reportable accident that occurs, containing information on the accident’s location, severity, classification, activity, and nature of injury, etc. A short narrative is generally included as well. Accident reports can be searched by many of the above fields. From 1996 to 1998, miners suffered a total of 55,096 injuries, which ranged in severity from death (degree 1) to injuries with no days away from work nor restricted duty (degree 6). Six percent of the total injuries were from falls of ground, including machine accidents where caving rock was coded as the source. As the data in Table II indicate, 98% of all non-fatal fall of ground injuries occurred in underground mines, with underground coal mines accounting for 83% of the total. Table II also shows the distribution non-fatal fall of ground injuries by severity and commodity. The injuries are classified into Lost Time Injuries that resulted in permanent disability (degree 2) or days off work (degrees 3-4), and Injuries Without Lost Time that resulted in no more than restricted duty (degree 5-6). Overall, groundfall injuries appear to be more serious than other types of mining injuries. 65% of all ground fall injuries resulted in lost time compared to 54% of all types of mining injuries.

By Francois Clerf

IRON ORE fields are situated in both the East and West of France (see maps). The eastern deposit is by far the most important from a tonnage point of view, not only in France, but in all Europe. The ores of this region are known as minette, and are situated in the Lorraine ore fields and the Briey plateau. The iron ores of the West are those of Normandy, Anjou and Brittany. Before the war, a large number of important German companies had acquired considerable interests in these western fields and a heavy trade with Westphalia had begun. Recently, however, conditions have changed and some of the mines of Brittany and Anjou are now idle. From a geological point of view, in Anjou and Brittany, a series of synclines extends from the northwest to the southeast, containing a number of seams of varying thickness and generally intercalated in Silurian and sometimes in Devonian formations. The ore is generally a hematite or a magnetite. The composition varies from 48 to 52 per cent of iron and from 8 to 12 per cent of silica. Con¬servative estimates indicate a con¬siderable tonnage of workable ores (150,000,000 metric tons).

Jan 1, 1936

The theme of my address to your Institute, indeed its name, is "The Mineral Industry - What Next?" Knowing that I was required to make four appearances, and not wanting to be too repetitious, I wrote a rather long speech of which I will deliver various sections at different places, with a common introduction. Specific areas I have addressed are "Exploration", "New sources of minerals and energy", and "Mining and metallurgy of the future".

Jan 1, 1984

By Guillermo V. Borquez

The economics of open pit mine design are dictated by three basic elements: cut-off grade, stripping ratio and slope angle. Although these elements are functions of a number of independent parameters, they are interrelated through their influence on the overall economics. The optimum slope angle is the most uncertain element to determine, because rock mass properties are difficult to obtain. However, for preliminary estimation, the slope angle can be determined from the relationship between the probability of failure and the safety factor. The economics of the slope selected will depend on a profit versus risk judgment. In this paper, the author will present an actual case of application of this postulate.

Jan 1, 1977

By J. Van Kleunen

In the Spring of 1959 the Riverside Cement Company, a Division of American Cement Corporation, placed into operation at their Oro Grande California plant a new crushing-blending-reclaiming facility. This new facility, in conjunction with other modernization in the plant, has established a degree of automation and reliability on a-plant-wide basis which heretofore had not been attained in the industry. The blending and reclaiming facilities for raw stone and cement clinker at this plant represent not only the first computer programmed materials handling system of its type in the industry, but also the first installation of specialized equipment which was designed for high capacity, fully automated operations.

Jan 1, 1963

By S Brochot

In cases where coarse gold is present in a deposit, it is usual to use the screen fire assay (SFA) method to analyse the samples. There is no doubt that this method is more accurate than the standard fire assay (FA) and reduces the risk to have a systematic bias. Nevertheless, the difference between the analytical errors of both methods can be glossed over when the overall sampling error is added to obtain the measurement error. In that case, the advantage of the SFA cannot justify its higher cost.The current paper attempts to address this question in the case of a gold ore deposit with visible coarse gold in various sampling situations (drill core sampling in exploration, blasthole or chip sampling in mining exploitation). The overall measurement error is estimated taking into account the analytical error and all the sampling error components following the Pierre GyÆs theory of sampling.Firstly, only the last sampling stage is considered when the pulverised sample is processed either to obtain one analysis sample for a FA or to be screened and subsampled for a SFA. The calculated measurement error clearly shows the advantage of the SFA specifically in presence of coarse gold. Secondly, the half core sampling is studied to explain the observed discrepancies when controlling the second half core. Finally, the blasthole sampling is treated using in situ heterogeneity models to show that the relative advantage of the SFA is hidden by the large overall sampling error.In conclusion, the choice of the assaying method is discussed at the light of the overall measurement error and in accordance to the analysis objective.CITATION:Brochot, S, 2012. Standard fire assay or screen fire assay? Application of the overall measurement error approach to choose the most appropriate method, in Proceedings Sampling 2012 , pp 135-142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By A. C. Rice

Investigation of a variety of mines to determine efficiency for rare- earth extraction has resulted in a solvent extraction technique wherein Primene 81-R,4 N-benzylheptadeeylamine (BHDA), and Primene JM-T give favorable extraction from sulfate solutions. Extraction from chloride, nitrate, and perchlorate solutions is negligible. Distribution coefficients for 10 rare-earth elements with Primene 81-R establish an extraction sequence beginning with lanthanum and proceeding through lutetium according to atomic number. Yttrium and ytterbium are exceptions in the extract ion sequence.

Jan 1, 1962

By George W. Maynard Maynard

IN this paper I desire to embody the results of some personal observations of the working of the Siemens direct process as I witnessed it for a part of three days at the works of the Siemens-Anderson Company, in Pittsburgh. This preliminary investigation was to have been followed up by one extending over a considerable period of time, and would have embraced analytical and physical tests. Circumstances over which I had no control, resulting in the temporary suspension of work, have postponed the presentation of a complete paper. If the opportunity is afforded me, I purpose doing this at a future meeting of the Institute. To those interested in the development of the process, reference is made to the papers of Dr. Siemens in the Journal of the Iron and Steel Institute for the years 1873 and 1877, and to the paper of our late lamented brother, Holley, in the 8th volume of the Transactions of our own Institute. Dr. Siemens, in the introduction to his paper "On the Manufacture of Iron and Steel by Direct Process," read before the Iron and Steel Institute in September, 1877, says: " In mixing comparatively rich iron ore in powder with about 25 per cent. of its weight of pounded coal, and in exposing this mixture for some hours to the heat of a common stove or of a smith's fire, metallic iron is formed, which, on being heated to the welding-point on the same smith's hearth, may be forged into a horseshoe of excellent quality. The admixture with the ore of some fluxing materials, such as lime or clay, will, in most cases, be of advantage to rid the iron of adherent slag." This is the keynote of the Siemens direct process. Dr. Siemens says further: "If we regard the production of wrought iron from an abstract point of view, we perceive that we have to accomplish two things, viz., the deoxidation of the ore, and the fusion of the earthy matter .mixed with it; and if we calculate the amount of carbon necessary to accomplish this end, we shall find that in using, say, hematite ore, consisting of peroxide of iron with from 10 to 15 per cent. of silica, we shall require barely 40 per cent. of carbonaceous matter per ton of iron contained in the' ore to effect its reduction, and also the fusion of the slag."

Jan 1, 1882

By Yuanbo Zhang, Yongbin Yang, Guanghui Li, Zhengwei Yu, Yufeng Guo, Tao Jiang, Xiaohui Fan, Youming Hu

"Composite agglomeration process (CAP), as an innovative method for preparing blast furnace burden, was developed and has been put into operation in China. CAP is different from traditional agglomeration processes of iron-bearing materials involving sintering and pelletizing. Compared to the traditional agglomeration processes, CAP is characterized by several strengths such as permission of diverse iron-bearing materials in production, obvious improvement of permeability in the feed bed, decreasing the fuel consumption and remarkably increasing the productivity of sintering machine. Furthermore, the use of the composite agglomerates prepared with CAP is capable of obviating the negative effects caused by the differences in quality of sinter and pellets on the operation of blast furnaces. This paper mainly presents an overview of the principle and applications of CAP.Development Background and Principle of CAPhe traditional agglomeration processes including sintering and pelletizing have been the two predominant methods for preparing ironmaking burden from iron-bearing materials. Sintering is a way for agglomeration by heating the coarser fine ores (general granularity 0~10mm). The mechanical strength of irregular porous sinter is obtained by the solidification of molten phase at high temperature process. It has been shown that the production of high basicity sinter (R=1.8~2.2) is characterized by low energy consumption and high efficiency compared to low basicity sintering. Meantime, the finished high basicity sinter is characterized by good mechanical strength and metallurgical performance. Pelletizing is another way for agglomeration by firing wet green pellets, which are balled from the fine grained iron ores or concentrates. Based on the differences of chemical compositions, the finished pellets can be divided into acidic oxidized pellets, fluxed pellets, magnesium-bearing pellets, and so on. The acidic oxidized pellets are the dominant products of modern pelletizing."

Jan 1, 2012

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By Carlton D. Hulin

ARE we a "have" or a "have-not" nation in our domestic supply of metals and minerals? Impinging on the ears of a people weary of war and faced with the problems of reconversion to peace, the import of this question has built up with the momentum of an avalanche. Stemming from statistics cited by Pehrson and accelerated by the pessimistic and possibly biased statements of Ickes, hardly an issue of any technical periodical dealing with mining has appeared during the past year but within whose pages was to be found some comment, some discussion of the question: Are we a "have" or a "have-not" nation? We have proved commercial reserves of high-grade iron ore in the Lake Superior region sufficient for 22 years, based upon the prewar rate of consumption; commercial copper reserves to last only 34 years, one fourth being inferred ore; zinc sufficient for nineteen years, over half being inferred; lead for twelve years, two thirds of which is inferred; mercury for only three years. So read the figures. Although admitting that these figures may be extended by new discoveries, by the use of marginal and submarginal ore, and by further technological advances, are we nevertheless to assume complete pessimism in the acceptance of the meaning of these statistics; are we to expect a rapidly increasing dependence upon foreign sources of mineral supply; are we to believe that we are at or near the peak of the "metal age" as has been held by Theodore J. Hoover? Or is some more optimistic viewpoint possible?

Jan 1, 1947