Search Documents

By Fiseha Tesfaye, Pekka Taskinen

"Thermodynamics of the equilibrium phase assemblage Ago_9Cul.lS-Cu2-xS-CuS have been studied by an EMF -method. The ternary phase was synthesized from the pure Cu2S and Ag2S in vacuum furnace at high-temperature and mixed with appropriate compositions of Cu2S and CuS to form the cathode electrode. The EMF-measurements were made on the solid-state galvanic cell Pt(-) I Ag I RbAg,ils I Ago9Cu1.1S-Cu2-xS-CuS I Pt(+), in a temperature range from 316 K to 498K.Based on the measured EMF vs. T relations, thermodynamic functions (?fG° , ?fS and ?fH°) of stromeyerite (Ag0.9Cu1.1S) in equilibrium with Cu2-xS and CuS have been determined. The obtained experimental values have been compared with the available literature values. New experimentally determined thermodynamic properties of the solid solution (Ag,Cu)2Sss were determined.IntroductionDue to intense mining of high grade sulfide ore minerals in the past, recently, the available sulfide ores are poor in metals and becoming increasingly complex; such that, the production of high grade metals by the conventional pyrometallurgical processes is compromised. Consequently, smelters are in need to modify their operating flow sheets and strategies for processing more complex feed materials economically, while meeting the strict environmental regulations. To make the appropriate modifications, accurate thermochemical data of phases and phase assemblages which exist in these complex ore minerals are essential.Silver-bearing sulfosalts are encountered in ore minerals for the production of base metals and are common sources of silver. Among the silver-based sulfosalts, stromeyerite (Ag0_9Cu1.1S) is relatively common ore mineral in most hydrothermal vein and replacement deposits [1]. Recently, the ternary chalcogenide compound Ago0.93Cu1,07S has been studied, intensively, due to its high ionic conductivity and gradual disorder in the sequential phase transitions [2]. Therefore, accurate knowledge of the thermodynamic properties of stromeyerite has considerable fundamental and practical interest in many aspects of extractive, chemical and physical metallurgy."

Jan 1, 2014

By Huai-ying Ma, Jun-hua Zhao, Xia Zhao, Si-bin Zhang, Wen Pan, Zhi-xing Zhao

Ignition is the start point of the sintering circuit, which plays an important role during the whole sintering process. The gas consumption accounts for 80% energy cost in the sintering ignition process. Therefore, gas flow reduction is of great significance to energy conservation in the sintering ignition process. In current study, the concept of comprehensive ignition intensity (CII) was introduced to determine the ignition effect. The experimental results indicate that the value of CII increases with higher air-fuel ratio at gas flow of 550 and 600 Nm3/h. From another point of view, given constant CII value, lower gas flow can be achieved with higher air-fuel ratio. Based on the comprehensive ignition intensity, the ignition parameters were optimized and the gas flow was subsequently reduced. By increasing the air-fuel from 5.5 to 6.6, the gas flow is reduced from 450 Nm3/h (8.1 GJ/h) to around 350 Nm3/h (6.3 GJ/h).

Mar 1, 2018

By Luis Bergh, Juan Yianatos, Luis Vinnett

"Process automation as an engineering discipline is more than control systems since it includes industrial instrumentation, such as sensors, transmitters and actuators, as well as control and supervision systems, collection and transmission of data and real-time software applications to supervise and control the operation of plants or industrial processes. In the last several decades, accelerated technological development has provided a variety of software and hardware tools to aid development, maintenance and continuous improvement of automated systems. These developments however seldom reach their full potential in real plants. There are many factors to be considered, among them human capital specific training and the organization model. In this paper, a methodology for training engineers in advanced control and supervision of flotation plants is presented based on study of the application of these technologies in hybrid pilot plants. Since experimentation in real plants may present undesirable risks and costs, and simulation studies are usually limited to some unrealistic conditions, a laboratory where on-line measurements of the hydrodynamic behaviour of a pilot plant is mixed with phenomenological models has been created. In this form, an environment as close as possible to a real plant can be recreated. A flotation column and a circuit of three pneumatic cells are fully instrumented and connected to a PLC and PC network. In the control room, students learn applications of classical PID control in a DCS environment, advanced predictive control, on-line process operation diagnosis, fault analysis, virtual sensors and expert-fuzzy systems. Several undergraduate and graduate courses and theses are supported by this Process Control Laboratory infrastructure. Examples of these applications are discussed."

Jan 1, 2014

The Johnny Mercer lyrics 'You've got to accentuate the positive, Eliminate the negative, Latch on to the affirmative à' would best sum up the traditional approach to community relations in the mining industry. This '90s 'Public Relations spin' approach, usually backed up by scientific data, technical reports and graphs outlining risk probability and the impact potential on people and communities, is being challenged. Challenged by communities who have greater access to information, demand greater levels of transparency and corporate responsibility of large corporate operations and possess greater awareness of the communities they live in.   The growth of the environmental movement, of anti-globalisation, anti corporatism, apprehension of a large corporate's ability to deal with community issues, and a lack of faith in the abilities of regulators to regulate corporate activities, means our industry faces challenges on multiple fronts. It must now be able to address these from a personal/community perspective if it is to remain relevant within communities.   One of the keys to this is linking the internal activities and responsibilities to the externals concerns and demands for higher levels of operation and care.   This presentation draws on Corporate Public Affairs trends, functions and approaches and the application to External Affairs activities within Newmont Waihi Gold's operations in Waihi and regional exploration activities throughout the Hauraki Goldfields.   The approach presented works on the philosophy that communities don't necessarily have to like what we do, but should be able to identify and recognise the way in which we involve them in decision making, communicate our intentions and respond to issues.

Jun 1, 2010

By Ken J. Brouwer

Stillwater Mining Company commenced construction and development of the East Boulder underground mine in 1998. This new PGM mine is situated adjacent to the East Boulder River approximately 35 miles south of Big Timber, Montana. Project planning and development incorporated detailed collaboration between the regulatory agencies, concerned citizens and mine personnel. A unique ?good neighbour agreement? was established with a local environmental group who have become actively involved in the review of ongoing site development and the implementation of environmental and compliance monitoring. Environmental management systems allow for integrated management of tailings, waste rock and water in order to minimize surface disturbances and to prevent adverse impacts to the East Boulder River. Long-term site development plans contemplate implementation of comingled waste rock and paste tailings. Water management capabilities allow biological treatment of all excess mine water in order to reduce nitrogen loadings prior to land application disposal by means of spray evaporation, snow making and land application. The comprehensive waste and water management plans have also been integrated with staged mine development and interim reclamation requirements.

May 1, 2002

By Don Eby

The application of electric arc furnace smelting of lead, antimony, and tin bearing slag from a reverberatory furnace will be discussed. The selection procedure for the 4.0 MVA electric arc furnace in Indianapolis, Indiana is presented. The design criteria for the transformer, electrodes, refractories and associated equipment is presented. The operation of the furnace including chaJ:9ing, bullion tapping, slag tapping, ventilation, slag composition, metal recoveries, and toxic leach results of thra.1 away slag are discussed. Flow charts and the equipment specifications are given.

Jan 1, 1990

By B. A. Eaton, K. E. Brown, C. R. Knowles, D. E. Andrews, I. H. Silberberg

This paper presents the resitlts of an investigation of two-phase, gm-liquid flow in horizontal pipelines. Experimental data were taken in three field-size, horizontal pipelines, two of which were constructed for this purpose. The data were obtained using water, distillate and crude oil separately as the liquid phase, and natural gas as the second phase. Experimental pressure-length traverse, liquid holdup and flow-pattern data were collected for each set of flow rates. These data were used to develop three correlations that are presented herein. The liquid-holdup values correlated with various flow parameters without regard to the existing flow pattern. The same was true for the energy-loss factors. A new flow-pattern map is presented that appears to be quite reliable, but not required for the pressure-loss calculations. The liquid-holdup correlation and the energy-loss factor correlation are used in conjunction with a two-phase flow power balance, developed during this study, to predict the pressure losses that occur during gas-liquid flow in horizontal pipelines. A recommended calculational procedure is given, as well as a statistical analysis of the results. This procedure lends itself to computer application, since several small pressure decrements are needed to calculate a pressure-length traverse. The correlations are shown graphically, but may be curve fitted with existing curve-fitring computer programs. INTRODUCTION Due to the frequent occurrence of gas-liquid flow in pipelines and the desire to accurately calculate the pressure losses that occur in these lines, two-phase flow is of considerable interest to the petroleum, chemical and nuclear industries. In the petroleum industry, gas-liquid mixtures have been transported over relatively long distances in a common line due to the advent of centralized gathering and separation systems. Long two-phase flowlines are usually accompanied by large pressure drops which influence the design of the system. Gas-lift installations are designed on the basis of known tubing pressures at the wellheads. The horizontal flowline connecting the wellhead and the separator system must be correctly sized in order to minimize the horizontal flowline pressure losses and the wellhead tubing pressure. Practically all oilwell production design involves horizontal two-phase flow in pipeknes. All of the flow processes of oil and gas production must be studied simultaneously to insure good well design. Since the beginning of offshore oilfield development, long horizontal flowlines have been constructed. Because pressure losses greatly influence the performance of producing wells, a method is desired that can be used to predict such pressure losses and select optimum flowline size. Several types of gas-liquid flow exist, and many of these are discussed by Gouse The study of pressure gradients, fluid distributions and flow patterns that occur in horizontaI multiphase flow is made difficult by the great number of variables involved. The various flow regimes give rise to changing velocities of the fluid particles in all directions. These instabilities of the interface between the gas and liquid prohibit the determination of actual vector velocities of fluid particles in each phase. Also, it is practically impossible to arrive at correct sets of boundary conditions. Therefore, most investigators have concluded that a solution to the problem by the classical fluid dynamics approach, whereby the Navier-Stokes equationsM are formulated and solved, is far too complex. Other methods must be utilized to develop general correlations that will predict the behavior of gas-liquid horizontal flow systems. Multiphase flow studies have sought to develop a technique with which the pressure drop can be calculated. Pressure losses in two-phase, gas-liquid flow are quite different from those encountered in single-phase flow; in most cases an interface exists and the gas slips past the liquid. The interface may be smooth or have varying degrees of roughness, depending on the flow pattern. Therefore, a transfer of energy from the gaseous phase to the liquid phase may take place while energy is lost from the system through the wetting phase at the pipe wall. Such an energy transfer may be either in the form of heat exchange or of acceleration. Since each phase must flow through a smaller area than if it flowed alone, amazingly high pressure losses occur when compared to single-phase flow. Most investigators of horizontal two-phase flow phenomena have chosen to separate their experimental data into several groups of observed flow patterns or regimes.

By E. S. Bartlett, D. N. Williams

QUANTITATIVE values for the oxidation rate of unalloyed molybdenum in air at temperatures above the melting point (1460°F) of the characteristic oxide are contained in the literature as a result of previous investigations. Lustman' reported values corresponding to 0.36 in. penetration per day (IPD) at 1500 and 1600°F in still air, noting essentially no variation in rate with temperature. Jones, Spretnak, and Speiser' reported values corresponding to 0.14 and 0.13 IPD at 1500 and 1800°F, respectively, in still air, attributing the decreased oxidation rate at higher temperatures to a lesser accumulation of the corrosive molten oxide on the surface at the higher temperature as a result of increased volatilization rate. Harwood3 ecently summarized work in the field, presenting generalized data corresponding to 0.48 to 0.96 IPD at 1800°F and 0.55 to 0.83 IPD at 1700°F in slowly flowing air. In a recent program at Battelle, it became desirable to know more about the characteristic oxidation behavior of molybdenum under varying conditions of temperature and atmosphere. Using oxidation-test apparatus designed for dynamic, continuous recording of weight change during testing,' values for the oxidation rate of molybdenum were obtained at temperatures from 1400 to 2150°F. In addition the effect of air flow on the oxidation rate was studied briefly at temperatures of 1600, 1800, and 2000°F. Exhaust of the contaminated atmosphere from the oxidation chamber was effected by an impeller pump attached to a 3/16-in.-diam opening in the oxidation chamber. The volumetric exhaust rate (cubic feet per hour) was normally maintained slightly in excess of the input rate to avoid condensation of MOO,,' on the sample suspension rod. The entering atmosphere was preheated prior to admission to the oxidation chamber by a 1 1/2-in.-diam cup packed with shredded asbestos. The experimental data are presented in Table I. Comparing conditions 2 and 3 (taking into account the temperature difference) and conditions 8 and 9. shows that in the absence of forced exhaust an atmosphere of moving air results in greater oxidation rate than a stagnant atmosphere. The use of forced exhaust, as shown by comparing conditions 3 and 4 and conditions 14 and 15: resulted in an even greater increase in oxidation rate. By virtue of the size of the atmosphere input and exhaust openings, it was calculated that the exhaust velocity was about 60 times that of the input velocity for essentially equal volumetric flow rates. Because of the proximity (about 3/4 in.) of the exhaust port to the specimen, it is logical to assume that cleansing of the atmosphere immediately surrounding the specimen was accomplished much more efficiently by the exhaust flow than by the input flow at a constant-volumetric flow rate. Also, it can be seen by comparing conditions 4 through 7 and conditions 11 through 13 that increasing the rate of atmosphere flow (by increasing input velocity with a proportional increase in exhaust velocity) above some optimum value has little, if any, further effect on the oxidation rate. These results suggest that there is a maximum oxidation rate for molydenum at a given temperature which is obtained when conditions are maintained such that the partial pressure of MOO3 in the atmosphere surrounding the specimen is at a low value. By controlling the partial pressure of MOO, surrounding the sample, it is possible to control the rate of volatilization of MOO:, from the surface. This, in turn, affects the rate of oxidation, since the thickness of the MOO3 layer determines the amount of oxygen which will be able to reach the reaction surface.' When the liquid oxide layer is less than some critical thickness, i.e., when the volatilization rate is high, enough oxygen is transported to the active surface to permit oxidation to proceed at the maximum rate allowed by the kinetics of the oxidation reaction. However, if the volatilization of MOO,, is suppressed, the thickness of the layer of MOO3 on the surface increases, and the diffusion of oxygen through the oxide layer becomes the rate-controlling step in the oxidation process. The lack of agreement between the present results and those of previous investigators is presumed to be due to differences in removal of the oxidation product (Moo,) from the immediate vicinity of the sample. By comparing conditions 1, 5, 10, 12 and 14, it is seen that when forced exhaust was used the oxidation rate of molybdenum increased with increasing temperature. A rapid increase was observed between 1400 and 1600°F, attributable to the effects

Jan 1, 1959

By A. Michalkow

DELN ITE Mines Limited is located in Deloro township, on the west end of the south break of the Porcupine Camp. Mining operations are currently being carried out on the downward extension of a system of quartz veins in an andesite zone. This zone has been followed from surface to the present bottom level of 5,250 feet. The changing mineralogy of the vein system has involved an increase in tourmaline content from the surface downwards, so that the veins at the lower levels are composed of dark brown quartz-tourmaline. The drilling problem presented by these extremely hard veins was partially alleviated by the development and adoption of a one-inch drill bit. All blast-hole drilling is now done with the one-inch bit, without any difference in hole spacing.

Jan 1, 1962

By A Dunne, R Kruger, H Coleman, P G. Laurens

External and internal challenges in mining are increasing the difficulty and complexity of operating mines. The external mining environment has a big impact on mining operations and is driving the focus on safety, sustainable mining, green issues, profitability and productivity. There is a very high emphasis on ‘reducing cost to improve’, lower mining and beneficiation costs by eliminating waste/inefficiencies (reduce people, use less consumables, multiskilling, etc). The internal mining environment is getting tougher to operate in, with the deposits being more difficult to mine, more difficult to manage due to external pressure along with issues associated with maintaining quality, etc.Technological and environmental developments too numerous to mention, mean that cost control models, reduction in human resource numbers, as well as other drastic measures to curtail expenditure and increase profitability have become part of everyday business. The capability to manage the mining environment in a systemic manner has been lacking and this increases the pressure for performance on those individuals operating and managing mines.Working smarter has become crucial to ensure that businesses optimise the use of their resources, become more safety conscious, more productive and remain cost-effective, while recognising the importance of sustainable mining now and in the future. The logic of determining and managing to the capability of the mining value chain will be examined and the underlying assumptions or beliefs guiding behaviour and decision-making will be highlighted.In order to identify the obstacles in the mining value chain that hinder achievement of its full potential, the following questions have to be asked:What are the factors that influence the performance of a mining value chain?What is the design capacity of the mine?How can the inherent flow and value capacity of a mine be determined?What types of solutions will allow a mine to operate at its inherent flow and value capacity?This article will discuss the way we plan, measure, assess and manage the mine value chain, by addressing the following factors:balanced capacity versus flow and value capacity designthe use of averagingoptimising individual components in a value chain versus optimising the whole value chain.Optimising flow and value through the mining value chain is one of the three pillars of Mineral Resource Throughput Management (MR™). MR™ is an entrenched and academically supported philosophy that has been successfully applied in the past decade in various mines throughout the world by EXXPLEO, a mining and beneficiation consulting company. EXXPLEO has partnered with HCL (a global IT company) to embed the MR™ philosophy, methodology and toolsets into a formal software product called Synchronised Digital Mining (SDM). The SDM system will provide mining companies with a sustainable platform to effectively apply the MR™ principles and toolsets effectively across all operations targeting increased productivity, efficiency and profitability without having to train operations and management staff into expert MR™ practitioners to successfully achieve the desired results.CITATION:Dunne, A, Laurens, P G, Kruger, R and Coleman, H, 2015. Optimising flow in the mining value chain, in Proceedings Iron Ore 2015, pp 437–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By W. Mirihange

Considerable mechanical property decline is always observed at the Heat Affected Zone (HAZ) of AA 5083, This occurred as a result of the thermal effect on the hardened material, It is highly beneficial to have a prospective metallurgical procedure to overcome this decline of properties. Therefore, experiments were set to evaluate the effectiveness of a quick post weld heat treatment process with the AA 5083, Optimum results were obtained at 473K and with approximately 600 seconds time, The interplay between the time, temperature and mechanical properties are possible to explain by the Lifshitz-Slyozov-Wagner (LSW) theory and by considering the composition of the material.

Jan 1, 2005

By Tasuku Fuwa, John Chipman, David H. Kirkwood

Fe-C-Si alloys in silica crucibles were held at 1600°C in a controlled atmosphere of CO and Co2 and the approach to equilibrium was obsertsed. Results were not of sufficient precision to establish the activity and interaction coefficients. Observations 012 the equilibrium provided an average value for the standard free-energy change which differed by + 1.1 kcal from the earlier accepted value. The C-SL relation at other temperatures is calculated and shown graphically. IN the refining of steel in an acid-lined furnace, it is well known that, unlike in basic refining, a very significant amount of silicon may remain dissolved in the metal even when the carbon content approaches a final endpoint. Further, it is known that the residual silicon increases with increasing temperature. The quantitative relation between silicon and carbon can be calculated for equilibrium conditions from data already available on the Fe-C-O and the Fe-Si-O systems. Such equilibrium calculations could show us approximately the limitations within which the reaction would be expected to operate in practice. In the oxidation of a bath containing both carbon and silicon it is well known that at low temperatures silicon is preferentially oxidized first. It can be shown by calculation that at high temperatures carbon will be oxidized preferentially. It is the purpose of this paper to record direct observations on the Si-C relation by means of experiments carried out in an atmosphere of carbon monoxide for Fe-C-Si alloys contained in silica crucibles. When such a system is brought into equilibrium, at a fixed temperature, the composition of the liquid metal is governed by the following equations: Both K1 and K2 are known with a fair degree of accuracy, and may be calculated from the tabulated In general the percentage of CO2 is extremely small compared to that of CO and in the experiments to be described the partial pressure of the latter was generally only slightly below 1 atm. EXPERIMENTAL METHOD The induction furnace employed was the same as that described by Rist and chipman' and by Fuwa and chipman.2 It was modified slightly in view of the change from alumina to silica crucibles. The small silica crucible was surrounded by a thin susceptor of molybdenum sheet which in turn rested inside a zirconia crucible. Since the zirconia was subject to breakage, it was supported inside an alumina crucible. The charge consisted of 30 to 35 g of electrolytic iron along with the required amounts of refined silicon and graphite to produce a melt of required composition. Purified carbon monoxide and carbon dioxide were passed into the furnace through carefully calibrated flow meters. Two separate and independent series of experiments were carried out. In Series I (D.H.K.) the melt was held in the furnace at 1600°C for periods of time up to 6 hr. Samples were taken at intervals in silica tubes and were analyzed for carbon and silicon. The results of the last one or two samples taken from each experiment and the direction in which equilibrium appeared to be approached are shown in Table I. In Series II (T.F.) the silica crucibles were of less satisfactory strength and the melts were held at 1600° C for periods of only 2 to 4 hr. In heats number 29 to 45 inclusive, the metal was cooled in the furnace and the ingot itself served as a sample for analysis. In heat 46 and all subsequent heats, samples were withdrawn in silica tubes at the termination of the heat, and these samples were analyzed. The results of all of these experiments in which equilibrium appeared to be approached are listed in Table II.

Jan 1, 1965

By Charles Jones

(San Francisco Meeting, September, 1915) IN any discussion of this very large subject we are confronted at the outset with so many obstacles that at best only a fragmentary and rather disconnected presentation can be made of it, and my hope is that building from the few facts I have to offer a more complete knowledge may be secured. In the whole intermountain and Pacific. Coast region, west of Pueblo, Col., and from Canada to Mexico, there is no production of pig iron, and steel production is confined to the manufacture of a small amount of open-hearth steel from scrap. When we consider the area, the resources, and the several centers of population, this condition seems anomalous, even in. the face of every counter argument as to cheap water transportation, or other means of transport from the Atlantic Seaboard or from the iron and steel centers of the Middle West. This comatose condition, if such a term may be applied, is certainly riot due to a lack of all the essential materials and factors for success in iron and steel smelting, but is rather, I think, due largely to the general fact that it is only within a comparatively few years that the centers of population on the Pacific Coast have attained a size that would entitle them to the position of distributing or freight centers, or that the "back country" has been enough built up to make it sufficiently interesting to the railroads to foster trade from the local centers to the interior points rather than seek to supply such local centers and the interior by a transcontinental haul.

Jan 9, 1915

By G. R. Luster

In most current practice, the methods that are employed in technical evaluations of cement raw materials are deterministic; i.e., decisions among alternative raw mixes and alternative plant designs are reached with the aid of only "average" compositions and "representative" samples of the available raw materials. Nevertheless, cement plants are sensitive to raw-material variability, and uniformly high-quality raw materials are not so abundant as they once were. Some simple examples will illustrate how geological techniques can be combined with geostatistical and operations-research approaches to customize mining and processing systems to deal with variable raw-material compositions.

Jan 1, 1987

By Wolfgang Pietsch

DR iron') is a generic term for metallized product that results from the direct or solid state reduction of iron ore. In direct reduction, iron oxides are reduced to metallic iron in the solid state without an intermediate melting step. MIDREX ® Iron is the DR iron material produced in the MIDREX ® Direct Reduction Process. Except for some thermal and mechanical degradation, the external physical form of as-reduced DR iron is the same as the feed material. Chemically, oxygen associated with iron is removed leaving a very porous structure. Figure 1 is the scanning electron micrograph (SEM) of the internal surface of a MIDREX Iron pellet obtained from a Swedish oxide pellet during reduction at 760 °C. Figure 2 is the SEM of a polished and etched cross-section through the same pellet showing the amount of intraparticle porosity. As a result of this high porosity, apparent density of DR iron is relatively low, typically a¬round 2 g/cm3, and specific surface is extremely high, typically around 1.0 m2/g or more. Both density and specific surface depend on the raw materi¬al and the operating conditions of the direct reduction plant. Normally, more than 97% of the available iron is reduced into metallic iron with the rest mainly in the form of wustite (FeO). During direct reduction, the gangue in the iron remains essentially unchanged. Removal of oxygen and the corre¬sponding reduction in weight result in a slightly higher percentage gangue in the product than in the raw material.

Jan 1, 1976

By Derek J. Fray

The need for on-line sensors is outlined and it is demonstrated that the control of many processes is prevented by the availability of these devices. The use of solid electrolytes is described for the sensing of elements in molten pyrometallurgical phases. In the cases where there is no suitable electrolyte, the addition of a second phase of a compound containing both the element to be measured and the element whose ion is mobile in the electrolyte can be used. For the measurement of high concentrations of an element a method based on current measurement is proposed.

Jan 1, 1994

By Kurt A. M. Westerlund

The basic function of primary gas handling downstream non-ferrous pyro-metallurgical processes is cooling hot sticky gases to treatable temperature levels (e.g. entering ESP). That means managing efficient the critical gaseous components from a molten via a sticky to a solid phase. The article outlines the modem gas cooling methods combined with efficient heat recovery. Examples of the alternative use of recovered steam energy are outlined; as e.g. drying of concentrate and power generation. The heat transfer impact of the insulating dust is called fouling and circumstances causing fouling are described. Modem cooling surface design and cleaning techniques to keep fouling in reasonable limits are described. Leakage- and false air ingress into the gas handling lines often limits smelting capacity. The objective is generally to minimize the infiltration of air but it still takes place at open interfaces (e.g. at reactor hood, feed port). Leakage air at furnace roofs for example can be reduced to a minimum by adopting the pressure gas sealing used at present In-Bath-Lance furnaces. Modernization and optimization methods to de-bottleneck existing waste heat boiler gas cooling capacity by highly efficient surface cleaning systems and false air avoiding (e.g. bundle roof boxes, dust discharge) are detailed described.

Jan 1, 1999

By Noel Dent

The Electrodet@ Electronic Detonation System Wilere are we going with regard to Accurate, Reliable, Easy to Use and Cost Effective Initiation using electronic initiation techniques? Improvements and applications in theJierd

Jan 1, 1995

By Darcey Baker

Quarry Blasting is usually boring, and that is how we like it. By this, boring means routine, straightforward, meat and potatoes blasting. Quarries typically will not utilize cast blasting, coyote tunnels, or any of the other more spectacular blasting techniques – just plain, old day-in and day-out quarry production and possibly overburden blasting. Differences in material characteristics, mining method, equipment availability, and target markets all play a part in determining the blasting procedures employed at any given location. However, variables exist everywhere and with foresight and planning, effects of tangible variables can be minimized. Variables caused by geology, weather, neighbors, or limitations caused by major plant or mobile equipment are, generally speaking, intangible; and leave the operator with finite options to improve or modify blasting procedures.

Jan 1, 2009

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006