Search Documents

By John B. Hastings

TEN miles from Hartsel, near Antelope springs, in Park county, Colorado, there is a large area of unconsolidated lake beds, which are interesting because at least a part of the lacustrine sands contains in the aggregate an immense amount of gold. During 1906, one of the arms of this dessicated lake was fairly well prospected with shafts and cuts by an Eastern company to test its value, as favorable amounts of gold had in some instances been found upon it. The claims of the company contain about 5,000 acres of the beds; but this is only a small portion of them, a south branch from a main body, which is at least 7 miles in diameter, with other and very wide lateral gulches, paralleling the one herein described on the east and west. A certain amount of digging and sampling was done in the outside areas; but the result was evidently unsatisfactory, since the work was discontinued. his section of Colorado has not been studied geologically, and the age of the ancient lake is unknown. It is probably Quaternary. I spent two weeks on the ground, in September and October, 1906, but was quite absorbed in the sampling. I looked, however, for terraces on the rim-rock and other evidences of movement and erosion, but did not find anything to denote an earlier age than the Quaternary. The granite rim-rock may be Archean; S. F. Emmons says that some of the granites in central Colorado are as old as that. The rim-rock as observed is a gray quartzose biotite-granite, except a small area in Sections 3 and 34, where it is a felsitic (?) breccia. The breccia is silicified by solfataric action at the corner near Shaft No. 7, in Section 34; but this action is older than the sands and does not extend to them. The shaft averaged 50c. per ton, more than twice as much as the rest.

Jan 5, 1908

By Petri Bryk, John Ryselin, Rolf Malmstrom, Jorma Honkasalo

THE theoretical possibilities for the realization of flash smelting have been known for a long time. Calculations concerning the same can be found in previously published literature,1 and suggestions for its accomplishment in practice are described in patents on the subject. Likewise a smaller number of practical test results are known. Autogenous smelting is closely connected with flash smelting, since in flash smelting techniques it is possible to use the heat evolved by oxidation of the sulfides for the smelting process to such an extent that under certain conditions smelting can proceed without additional fuel. However, in the event that insufficient heat is available from the oxidation of the sulfide concentrates, then additional heat may be supplied by preheating the air, using oxygen enriched air, on burning additional fuel with the concentrate.

Jan 6, 1958

By Alessandra Bonoli, Garfìm Marianna

"Construction and demolition waste (CDW) is no dangerous material resulting from construction, and demolition of houses, large building structures, roads, bridges, piers, and dams. It is possible to recycle these materials, to reduce environmental impacts, and to reuse them in construction sector. To evaluate in a correct way the possibility to reuse this material it is important to lead laboratory tests to assess the proprieties and quality characteristics. European, Italian and British ad hoc Committees had elaborated specific Standards, to evaluate Geometrical, Physical, and Chemical requirements of recycled materials. A research was carried on to define the guidelines for laboratory tests, their suggested values and quality standards. The Construction and Demolition Waste Construction and demolition waste (CDW) is no dangerous, uncontaminated material resulting from construction, renovation, repair, and demolition of houses, large building structures, roads, bridges, piers, and dams. CDW waste is made up of wood, steel, concrete, gypsum, masonry, railway ties, roofing materials, carpeting, insulation, plaster, metal, and asphalt, and all waste included in CER Code 17. In particular Demolition wastes are defined as materials resulting from the demolition, instead Construction wastes are defined as waste materials resulting during construction process or in pre-manufacturing construction industry. Environmental problems In a lot of cases Construction and Demolition Waste materials were discharged in landfills, these are filling up with CDW and others, and some of them will close in the near future. In addition, illegal dumping of CDW debris can result in future health risks, decreased property values, cleanup costs and enviromental problems. The typical environmental impacts generated by CDW dumps are: 1- Dust problem, which causes air pollution, as will as forming dirty areas. 2- Uncontrolled locations, that will encourage the disposal of other waste types with the usual construction wastes leading to an environmental disaster. 3- The degradation and deterioration of the coastal lands and the natural protectorates. 4- The loss of aesthetic features. 5- Occupation of large areas, causing extra hauling costs. Therefore, it is wise to find other alternatives, like reuse or recycling, other than landfilling CDW debris or illegal dumps, because a proper management and the reduction of CDW amount can save money, conserve resources, and preserve the environment."

Jan 1, 2008

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003

By S J. Schafrik, E S. Gilliland, E C. Jong, J Waynert, C W. Weiss

Two commercially available through-the-Earth (TTE) communications systems were evaluated at an active underground longwall mine in West Virginia. One system utilises magnetic field (H-field) antennae while the other system utilises electric field (E-field) antennae to achieve communication. A large portion of this mine is overlain by an inactive gas-oil field composed of densely spaced wells. This feature provided a unique opportunity to determine the impact of cased wells on both TTE technologies. The following communication modes were investigated: surface to underground, underground to surface, underground to underground and real-time two-way communications. Standard deployments of the TTE systems using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations under certain circumstances. As a result, the design and deployment that will optimise TTE transmissions are unique to each system and to the specific area of the mine. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivity. The performance of these two TTE systems suggested that one may be preferable over the other depending on the conditions present during deployment.CITATION:Jong, E C, Schafrik, S J, Gilliland, E S, Weiss, C W and Waynert, J, 2015. Pairing magnetic and e-field through-the-Earth communication systems based on mine site conditions, in Proceedings Third International Future Mining Conference, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By R. D. Brown

There are techniques for separating aluminum alloys from mixed scrap, but there are no efficient ways to separate wrought aluminum from cast aluminum. This Bureau of Mines report describes a novel technique for separating mixed aluminum alloy scrap into cast and wrought aluminum alloy fractions. The technique, which uses conventional heating, fragmentizing, and screening equipment, exploits differences in the mechanical properties of cast and wrought aluminum alloys at elevated temperatures. The cast alloys become brittle at high temperatures owing to intergranular melting of regions of eutectic composition. This melting begins to occur as the solidus temperature for each alloy is reached. Solidus temperatures for casting alloys generally range from 520° to 580° C, but are above 600° C for most wrought alloys. Thus, the casting alloys are easily fragmented while the wrought alloys remain ductile in the proper temperature range. Starting with a mixture containing approximately 80 pct cast and 20 pct wrought alloys, fractions of 100 pct cast and 98 pct wrought have been produced.

Jan 1, 1985

By David Thomas, Charles Harper, Brian Watters

The Star-Waddy Lakes area lies withjn the northeasterly-trending early- to mjd-Proterozoic volcanoseilimentary-pl utoruc belt referred to as the La Range Domllin. In the area investigated the domajn is composed of the Central Metavolcaruc Belt which is bordered by metasedimentary belts of the Crew Lake and MacLean Lake Belts to the northwest and southeast respectively. The boundaries between the Central Metavolcanic Belt and the flanking belts are generally marked by prominent zones of shearing. The volcanosed imentary succession is intruded by a variety of ultramafic to felsic plutons which, on the basis of lithology, field relations and geochronology, can be broadly subdivided into three groups or episodes. These are: a) an 'early' (ea. 1866 Ma), possibly subvolcanic, episode marked by composite intrusions ranging from gabbro-diorite to granite, b) an 'intermediate' (ea. 1854 Ma) plutonic event distinguished by more homogeneous felsic intru ions ; and c) a 'later' (ea. 1835 Ma) event characterized by leucocratic quartz-rich grani te intrusions. The La Range Domain has undergone polyphase deformation with a strongly developed northeast-trending structural grain. Large scale folding is manjfested by large regional sy nforms, arcuate and triangular patterns associated with many of the plutons and by tight to isoclinal folds within the adjacent metasedimentary belts. Inhomogeneous strain characterizes much of the Star-Waddy Lakes area. With strain gradients being typically very steep, zones of high strain consisting of zones of extreme extensional fabrics, discrete shearing, as well as broader zones of cataclasis and structural slicing, are often juxtaposed with areas of relatively minimal deformation . Dilation structures tend to favour these zones of highly contrasting strain. Late, brittle fractures, faults and shear zones are widespread and appear to be particularly important as loci for gold mineralization. Metan1orphic mineral assemblages indicate that upper greenschist to middle amphibolite facies conditions were attained. Geological and geochenucal evidence indicates that the Central Metavolcanic Belt evolved in an island arc environment. Metavolcanic rocks from both the Waddy and Star Lakes areas display similar characteristics on variation diagrams (e.g. AFM and the Jensen cation plot) in that the dominant trend is calc-alkaline with some basic to intermediate types having a mildly tholeiitic character. A few samples from the southern end of Lower Waddy lake display komatiitic to basaltic-komatiitic afl'injties. The relatively immobile minor and trace elements (e.g. Ti , Zr, Nb, Y, Cr) provide reliable characterization of the metavolcanics, particularly of the basalts, which have highly distinctive trace element properties. Geochemical patterns for the basalts are similar to those for modem volcanic arc basalts. Low initial 87Sr/86Sr ratios (0.7017 - 0.7019) are consistent with a subduction-related origin for the volcanics. The major plutons have chemical properties typical of volcanic arc granites and are largely calc-alkaline in character, showing little chemical variation from the volcanics.

Jan 1, 1986

By Roy C. Bartholomae

An accurate characterization of the vibration environment and a vibration qualification test derived from it will be a very useful tool for manufacturers of instrumentation for use on underground coal mining equipment. Recognizing this, the Bureau of Mines sponsored a study wherein vibration levels were measured on mining equipment to form a basis for developing the required vibration test. The data base was composed of 160 samples taken at different positions on a variety of underground machinery. The data were analyzed and presented in a format typical of military vibration qualification tests. The form was shown to be virtually identical to the swept sine test envelope specified in MIL-STD-810B for tracked vehicles.

Jan 1, 1982

By Charles E. Van Barneveld

RBH Note: the following item is a little different than the usual, in that it shows how explosives were used in the past to assist in putting down holes for iron ore prospecting on the early Mesabi Range of Minnesota. The way explosives were used would not even occur to the modern explorationist, given the equipment available today. The reason for the great difficulty in putting down a hole was that the area was covered with debris from the great glaciers of the past (the same ones that carved out the Great lakes). This debris consisted of boulders, clay, sand, and any other imaginable mixture of materials.

Jan 1, 2013

By Arthur V. Corry

GOLD was discovered in Alder Gulch, Virginia. City, Mont., on May 26, 1863. In a short time some 6000 people flocked to the new discovery, and on the banks of Alder Gulch six settlements sprang into existence, the principal one, Virginia City, alone surviving. This town today has a population of 800, and is the county seat of Madison County. It is estimated that between forty and fifty million dollars in gold was produced up to 1904. Virginia City is situated at the mouth of Alder Creek where that stream leaves the narrow canyon that cuts the steep foothills flanking Old Baldy Mountain, elevation 9572 ft., 12 mi. south. Virginia City itself is 5700 ft. above sea level.

Jan 1, 1936

By Mihaita Matei

An adaptive approach to control the deformation in tube hydroforming process is presented. This requires: the use of an existing non-linear FE software (ABAQUS) that incorporates a user material model (VUMAT), the development and implementation of an adaptive control strategy to coordinate the internal pressure and the axial load so as to prevent fracture and wrinkling failures (knowledge-base controller) and the application of the developed adaptive simulation approach for finding the optimal loading path required to hydroform a defect-free part with as uniform thickness distribution as possible (user's load subroutine (VDLOAD). In order to validate the approach, the case of conical hydroforming and the case of bending followed by hydroforming component is discussed.

Jan 1, 2011

By D. D. Tannant, H. Ozturk

Thin spray-on liners are increasingly being used as rock support in underground mines. The adhesive strength between the liner and the rock surface is an important design parameter. Adhesion tests were conducted to assess the impact on adhesion of the presence of oil, water, and dust on a substrate, and the roughness and grain size of different substrates. Other factors such as curing time, loading rate, and liner thickness were also considered. Adhesion was measured using a pull test of a 33 mm diameter elevator bolt attached to an over-cored section of liner with strong epoxy. Most tests were performed using Tekflex liner material, although five other liner products were also tested. Adhesive strengths of about 2 MPa can be achieved with Tekflex under optimal conditions. Long-term creep tests showed that the adhesive strength could drop by at least 50% when the liner carries load for about a month. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa. As the thickness of the liner increases, the adhesive strength to a substrate appears to decrease.

Jan 1, 2007

Jan 1, 1879

By P. G. Mason, H. T. Brown

Electrowinning of nickel at the Bindura Smelting and Refining Company by H. T. BROWN, B.Sc. (Member) and P. G. MASON, B.Sc. (Member) After a brief discussion of theoretical considerations in the electrowinning of nickel, an account is given of the electrowinning process and plant used at the Bindura Smelting and Refining Company.

Jan 2, 1977

By G. Broadbent

It is an honour to be invited as a speaker to this ICCR conference and a pleasure to be with you here in South Africa. I have been asked to talk about the competitiveness of coal versus other energy alternatives. Coal supplies nearly one-quarter of the global primary energy. Its most direct competitors are gas, nuclear and renewables. Oil is predominantly for transport fuels. Fuel oil is competitive with coal when crude is below its long-run average price and has some niche opportunities. But I will confine my comments to nuclear, renewables and particularly natural gas as the most potent current competitive threat to coal. Competitiveness is more than just cost and price; there is environmental acceptability, security or reliability and increasingly image. These factors are more of a spectrum than discrete issues. Dollars and cents remain the key issue for competitiveness but one must recognize the impact of politics in sustainable development and energy security.

Jan 1, 2001

By Joseph A. Sopko

The first documented procedures for designing frozen earth structures are over 50 years old, implemented long before the introduction of the Finite Element Method (FEM). Since that time, the development of three-dimensional models has made the traditional and often over-conservative methods relatively obsolete. This paper discusses a new approach that is largely dependent on the analysis of internal stresses with the frozen structure and comparison to frozen soil laboratory tests. A specific design process is discussed related to initial field investigation, laboratory testing, structural and thermal analysis, and performance monitoring. The design results are compared to case histories in the field that verify the procedure. BACKGROUND One of the first documented methods to designing frozen earth retaining structures was by Sangar (1968). Methodical refinements were published by (Harris 1995) and published by the International Symposium on Ground Freezing in 2002 (Andersland et al. 1991). The structural design or thickness of the frozen mass was based on the unconfined compressive strength of the frozen soils. Two simple equations for determining the thickness of a frozen shaft are shown in Fig. 1 and the first two equations below.

Jan 1, 2019

By Charles Himrod

IN presenting this paper it is not intended to enter into any discussion of the theory of the blast-furnace, but simply to give the results of a number of determinations of CO and CO2 in furnace gases, and some conclusions arrived at, and the result of an experiment made in hopes of increasing the production of CO2. In the first table, on page 198, is given the averages of a number of analyses of gases of different furnaces, and in the second, of two stacks of different sizes under varying circumstances. The conclusions arrived at as to what influences the production of CO2 are as follows: 1st. Kind of fuel. Bituminous coal not permitting the formation of as much CO2 as coke. 2d. Kind of ores. Rolling-mill cinder being much less favorable to formation of CO2 than hematite ores, magnetites probably less than hematites, but more than cinder. 3d. Length of time of contact of gases with ore. Small furnaces and too rapid driving both waste fuel by not allowing enough time for conversion of CO into CO2. 4th. The temperature of blast. The hotter the greater the quantity of CO2. 5th. Regularity of passage of stock through the furnace. The hanging and dropping of the stock, however slight, seems to pack it more solidly in the hearth, increases the resistance to the blast, and decreases the quantity of CO,. These are the most common causes noticed which influence the production of CO2, unless we except the one that might be considered the greatest of all, the one that has spoiled so many tons of iron, and the amiability of so many furnacemen, the one most dreaded, the great unknown. It would seem a self-evident proposition that the better the contact of the gases with the ore and the less with the fuel, the greater would be the amount of CO2 produced. To prolong the contact of gas with the ore furnaces are enlarged with advantage, and pains are taken to charge the stock in such a, manner as will best promote it. Still, with furnaces of most approved construction and most skilful manipulation, the gases leave the furnace so rich in CO, that not half the heating power of the fuel is obtained, and the highest

Jan 1, 1877

By H. W. Clair, E. V. Potter, M. J. Speedlove

"INTRODUCTION The behavior of particles in a sound field has long been of scientific interest since Kundt (1) 5/ made his classic experiments on some of the interesting effects of standing waves in cylindrical tubes. With the development of the electronic tube and its application to continuous generation of sound, experimental investigation of the Kundt tube was renewed (2). The more intense vibrations set up by a continuously vibrating diaphragm or rod produce even more striking effects than those observed by Kundt. Instead of the striations at the antinode produced by the stroked rod, then, wafer like barriers are formed at the antinodes, sometimes extending over the entire cross-section of the tube. Furthermore, it was observed independently by Andrade (3), Brandt, Freund and Hiedemann (4); and by investigators in the Bureau of Mines laboratories (5) that aerosols, such as ammonium chloride or tobacco smoke, could be flocculated quickly if passed through an intense sound field, particularly when a standing wave field was set up by a resonant enclosure. Because of its possibilities as a new means for removing suspended particles from dust-laden gaseous furance or smoke, the phenomena attending the behavior of suspended particles in a und field have been studied intermittently by the Bureau of Mines over the past decade.The first experimental work was done with a magnetostriction vibrator and a Hartmann air-jet generator as sound sources. It soon became evident that neither type was entirely satisfactory. Low mechanical efficiency is an inherent characteristic of magnetostriction generators, and the air-jet generator is difficult to control and does not permit accurate measurement of the acoustic output. The search for a suitable sound source led to the development of an electromagnetic generator, which is by far the most suitable for study of the effects of intensive high-frequency sound fields in gases (6)."

Mar 1, 1948