Search Documents

By R. C. Buehl

An experimental iron blast furnace of 3-foot-diameter hearth, producing about 12 tons of metal per day, was operated for 2 weeks with various proportions of anthracite replacing a corresponding amount of coke. The furnace operated well with anthracite in amounts up to 40 percent of the total fuel and produced metal of uniformly low sulfur and normal silicon contents. An increase to 50 percent anthracite during two attempts resulted in poor operation and the charge hung in the s haft of the furnace. INTRODUCTION Anthracite production in Pennsylvania decreased from 84,400,000 net tons in 1926 to 40,600,000 net tons in 1952, and there was a further decline in 1953 to 30,900,000 net tons. Employment in the anthracite industry dropped from 165,000 men working an average of 244 days per year in 1926 to 57,900 working an average of 163 days per year in 1953,3/ which has naturally resulted in considerable unemployment in the region. The industry is actively engaged in promoting new uses for anthracite to increase the demand and thus improve economic conditions in the region. One possibility is the use of anthracite to replace part of the coke for smelting iron ore in blast furnaces. The tests in this report were made to determine whether this use of anthracite would be feasible.

Jan 1, 1955

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Dale E. Wittmer

Nonoxide ceramic materials could substitute for high-temperature alloy steels containing imported critical and strategic materials such as cobalt, chromium, and nickel if their high-temperature properties can be improved. An important result of this substitution would be a reduction of the Nation&apos;s need for imports of critical and strategic materials. In this Bureau of Mines investigation, the primary objective was to produce high-purity u1trafine (particles <5 ~m equivalent spherical diameter (ESD)) alpha-silicon carbide (a-SiC) powders with improved high-temperature properties using the Bureau&apos;s patented turbo-milling process. A secondary objective was to determine the feasibility of using polymer mill construction materials as a means of eliminating metal contamination from the turbomill. U1trafine a-SiC powders with BET (Brunauer-Emmett-Te11er) surface areas from 30 to 35 m2/g (~0.06 ~m particle ESD) were produced in an all-polymer turbomi11. These high-purity powders (with I-pct Band I-pct C additions) hot-pressed to greater than 99 pct of their optimal density and exhibited properties commensurate with those of commercially available a-SiC. The most promising of the construction materials tested for the major wear surfaces of the turbomi11 was u1trahigh-mo1ecu1ar-weight (UHMW) polyethylene, a polymer thermoplastic.

Jan 1, 1984

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By I. H. Gundiler

Sandia National Laboratories (SNL) is tasked to support The Department of Energy in the dismantlement and disposal of SNL designed weapon components. These components are sealed in a potting compound, and contain heavy metals, explosive, radioactive, and toxic materials. SNL developed a process to identify and remove the hazardous sub-components utilizing real-time radiography and abrasive water-jet cutting. The components were then crushed, granulated, screened, and separated into an aluminum and a precious-and-base-metals fraction using air-tables. Plastics were further cleaned for disposal as non-hazardous waste. New Mexico Bureau of Mines & Mineral Resources assisted SNL in investigation of size- reduction and separation technologies.

Jan 1, 1995

By J. Sohn

The most promising near-term alternative to fuel cell driven vehicles is probably Hybrid Electric Vehicle (HEV or EV) technology. HEV technology combines the best characteristics of fuel-driven engines, electric motor drives, and energy storage components. It is designed with a combustion engine that functions as the primary power source, and an electric power storage system that functions as the secondary power source. The presence of the secondary power source allows designers to size the combustion engine for cruising power requirements. A new energy source for HEV or EV market will become lithium ion batteries (LIBs) in the near future. LIBs for HEV or EV has large scale about more 10,000 times than small size one for IT devices in order to achieve high electric density/capacity and high efficiency, etc. In those reasons, physical treatment of the batteries is more difficult for stable dismantling in comparison with the smaller one. Hybrid vehicle sales will grow by nearly 400 percent during the next seven years, according to a new report from analyst firm ABI Research. By 2013 hybrids will make up 6 percent of annual U.S. auto sales. The traction battery pack will become air-cooled LIBs which consists of several modules of Li ion battery and connected in series/parallel configuration to provide about >450 VDC, >150 kW peak power, and >80 Ah capacity. As the use of these batteries tends to increase significantly for the next years, it is relevant issues that development of new recycling methods as well as optimization of existing processes to treat spent LIBs for HEV have being addressed in order to obtain sustainability. In this study, physical treatment containing stable electrical discharge of spent LIBs for HEV was carried out for recovery of valuable metals from the batteries. Also In order to increase the yield of valuable metals through physical treatments such as electric discharge of spent batteries, crushing, and classification, we also focused on the recovery of cobalt from +8 mesh fraction due to its large portion in crushed intermediates.

Jan 1, 2010

By Robert F. Chaiken

An absorption-desorption model of particle reactivity was employed to describe the observed relationship between two apparently diverse phenomena which have been the subject of considerable study at the U.S. Bureau of Mines: (1) coal-rock dust reflectance and (2) coal-rock dust explosibility. The model accounts for heterogeneities in particle-size and material properties; however, in the present report, only particle-size distribution is considered. A mean particle-size parameter, appropriate to the explosion extinction process, is derived, and then taken as appropriate to describing optical reflectance. The derived form-to-function relationships for the two processes, when compared with experimental data, suggest that a problem exists with previously derived theory relating optical reflectance to rock dust concentration. A reexamination of that theory leads to a new theoretical expression, changed by a factor of 2, for the variation of rock dust concentration with reflectance which is in quite good agreement with experimental results. The current work offers justification for measuring and establishing rock dust requirements for specific coal dust size distribution(s) found in the mine-distributions that undoubtedly depend on the mining method and the type of coalbed.

Jan 1, 2010

By Jean E. Tilden

An investigation of several trace elements distributed among sulfide minerals from deposits located in the southeastern United States was conducted. The deposits investigated are distributed within both the Blue Ridge Province and the Piedmont Province, which are contiguous geographic provinces. Twenty five deposits were examined;&apos; eleven in the Blue Ridge Province and fourteen in the Piedmont Province. Figure 1 shows the locations of deposits investigated. In the deposits investigated, the mineral phases examined were pyrite, pyrrhotite, chalcopyrite, and sphalerite. These phases were chosen because of their relatively widespread occurrence, although no pyrrhotite was seen in the Piedmont Province. A total of 116 polished surfaces of ores were prepared, and mineral phases were collected from these surfaces for analysis. Samples were analyzed for cobalt, nickel, manganese, lead, tin, chromium, molybdenum, and gold. A total of 372 analyses were made. Trace elements were determined by atomic absorption spectrophotometry following standard procedures. In this study, trace elements are defined as those elements which are present in the mineral but which do not affect the chemical formula for that mineral. Lead is considered as a trace element only in ores where little or no lead sulfide could be identified as a distinct mineral phase.

Jan 1, 1972

By E. A. Collins

I TAKE it that the papers presented tonight on the subject of Reconstruction, as regards both gold and base-metals, are intended primarily to stimulate discussion of this important subject and, in regard to base-metals in particular, cannot in any manner be considered as a policy or plan to be followed as a panacea for all the ills which are bound to beset the industry when peace is declared. A famous cook-book written by a Mrs. Beeton contained a recipe for jugged hare which began with the instruction, "First catch your hare". To date, we have not caught the hare of victory and it may seem to many that any thought, energy, or effort devoted to the problem of reconstruction which will in any way impede the acceleration of the chase after victory will leave us open to the charge of being derelict in our duty as citizens. Much of our present trouble is due, however, to our lack of preparation for war in time of peace, and it follows that it is of equal importance in our national economy to prepare for peace in time of war. Most of us here tonight have vivid and sad memories of the chaos in the metal mining industry following the Great War of 1914-1918. In our own industry, mining, smelting and refining of nickel and copper, it was not a problem of absorbing the men who returned. There were only some three hundred who came back to the Mining and Smelting Division, and these men were all given their former jobs without any apparent difficulty. They were rehabilitated gradually due to the fact: that some of these men did not return for a year after the Armistice was signed. The numbers of men involved in the present conflict are much greater. We have to date in the armed forces upwards of 3,000 men enlisted from our employ.

Jan 1, 1943

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 3,924 samples, representing the products of 116 companies. The samples were collected during June, July, and August, 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers, The data were obtain& by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By J. B. Zink, M. J. Peterson

A semiquantitative spectrochemical method was developed and applied to the analysis of ash of U.S. coals . A low- temperature ashing procedure was used to minimize the loss of volatile elements . The analytical procedure provides for the estimation of 68 elements including major , minor , and trace constituents . Standards for the trace elements were prepared in a synthetic base mixture that approximates the average composition of U.S. coal ashes . Excitation was achieved with a d- c arc , spectra were recorded photographically , and interpretation was made by visual comparison of spectra of unknowns with spectra of graded standards series . Thirty- six trace elements were found in the analysis of 900 samples . Details of the procedure are presented , including sample and standards preparation , excitation and exposure conditions , spectral lines used , and approximate limits of detectability .

Jan 1, 1964

By Christopher Van Dyke, Knox Van Dyke, Lixin Wu, Jaime Gutierrez

"I. INTRODUCTION(SILICA, THE LUNG, INFLAMMATION, AND FIBROSIS)Inhalation of respirable-size silica (0. I to 5 µm in diameter) deposits the particles in the deep spaces of the Jung where oxygen is exchanged. The resulting pattern of inflammation is substantially different compared to that observed from other inhaled substances such as carbon, polystyrene titanium dioxide etc. 1 Following the inflammatory reaction the body attempts to isolate the damage by walling off the area via fibrosis. 2 The unique nature of the inflammatory response to silica makes it logical to infer that fibrosis is a later-stage manifestation of the initial inflammatory damage. In addition to the inflammation extensive lysis and cellular death particularly to macrophages and neutrophils, can occur, depending on the dose of silica.' The ingestion of significant amounts of silica by macrophages and neutrophils produces an inflammatory sequence which activates the lipoxygenase pathway of arachidonic acid metabolism and produces platelet activating factor (PAF) and leukotrienes (LT).4·5II. CALCIUM IONOPHORE MIMICS SILICA TOXICITY IN VITROPhagocytic cells exposed to silica in vitro produce PAF and LT. This response is reminiscent of phagocytic cells exposed to the calcium ionophore (A23 l 87) in the presence of ionic calcium.6-8 A23 l 87 forms a complex with free ionic calcium which passes through cellular membranes, thus transporting calcium inside the cell. The increased intracellular calcium concentration triggers the production of small amounts of prostaglandins large amounts of LT. PAF and. depending on dose cellular death (see Figure 1 ). Could silica cause LT production and cellular death by a similar mechanism? How could silica - an inert solid - act in a similar fashion as a soluble stimulant? Clearly the negative SiO2 and OH- surface of silica can bind calcium ions9 and therefore could theoretically act as a solid-state ionophore releasing bound calcium inside of cells following phagocytosis."

Jan 1, 1998

By Greg Canivan, Bernie Hertlein, Les Chernauskas, Joram Amir, Garland Likins, E. Anna Sellountou, Tim Kovacs, Peter Kandaris

Nondestructive testing of drilled shaft foundations via Crosshole Sonic Logging (CSL) is often performed as part of the quality assurance process to assess the soundness of concrete. The intent of CSL testing is to identify irregularities such as soil intrusion, necking, soft bottom, segregation, voids and other defects that could result in poor structural performance of the foundation. Over time, CSL rating criteria based on first arrival time and relative energy have incorrectly evolved to often be the sole means of determining the acceptability of a shaft. Some of these criteria have found their way into regulatory agency specifications, with acceptance values often differing from agency to agency.The purpose of this document is to review the state of the practice (including experience gained over the past 20 years), propose improved CSL rating criteria and make recommendations for additional assessment, as well as educate the industry on the proper interpretation of CSL test. CSL test results alone should not be the sole means of rejecting or accepting a shaft. A task force of industry exerts was formed to review the existing CSL rating criteria and propose improvements where appropriate. The recommendations presented herein are the consensus of the task force, which believes that they should be incorporated into future criteria, codes and specifications. This paper was produced as a joint effort between the Codes and Standards Committee, the Drilled Shafts Committee and Testing and Evaluation Committee. A task force was authorized under Testing and Evaluation Committee. The task force contributed their expertise in web-based discussions often every two weeks over a period of three years. Interested participants were invited to participate at any time. The document had two rounds of broad industry review, two rounds of DFI Technical Advisory Committee reviews, and a Public Comments process. All comments were considered in producing the final document.

Jan 1, 2019

By C. R. Dale

IT IS the purpose of this paper to point out a number of the most common causes of crooked holes; to outline methods of drilling and straightening which to my personal knowledge have proved successful in numerous cases; to describe some of the characteristics of holes which, though not crooked in an exaggerated sense, may still cause serious mechanical trouble if not recognized and properly remedied; and to define clearly the part of oil-well surveying in the concerted effort operators generally are making to keep their wells straight from spudding to completion

Jan 1, 1931

By William A. Hockings

This report describes the results of laboratory studies on leaching of copper ores.tlf These studies are the first step of a program for the investigation of in situ leaching of tabular, metalliferous ore bodies.(2) The basic steps required in the development of an in situ process are: 1. Leachability - the ability to dissolve the metal values from the ore under in situ conditions must be demonstrated. 2. Ore Preparation - the ore must be prepared so that sufficient contact with the solution can be attained. 3. System Design - integrated in situ systems must be designed and studied for engineering feasibility. 4. Economic Feasibility - the economics of the system must be shown to be economically feasible and competitive. 5. Environmental Feasibility - the loss of reagents into the environment must be investigated. 6. Pilot Scale Testing - the feasibility of the system must be demonstrated on a sufficiently large scale. The studies described in this report were concerned only with the first step of the program, viz., leachability. Native and sulfide copper ores from the Michigan copper district were selected as model ores for these studies. Aqueous amnonia solutions were chosen as the solvents to be investigated. In this study carbonate (CO3, HCO3, H2CO3) was used exclusively as the anion. In keeping with custom it is referred to as carbon dioxide and concentrations are ex- pressed in terms of CO2. When leaching native copper the reaction is

Jan 1, 1976

By John G. Kuhm

INTRODUCTION The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an orebody, no more and no less. This cost of development drilling represents a large part of the total development budget. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. This high development cost factor has produced a quantity of research to develop techniques, for efficient control of drilling programs. Recent mining literature is full of articles describing methods for measuring and increasing the effectiveness of these expensive projects. The method described in this paper was developed during the latter part of a major development drilling project at the Christmas Mine of Inspiration Consolidated Copper Company in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. This technique was used at Christmas as a practical means for evaluating adequacy of drilling on an individual hole basis, and it was possible to eliminate several previously approved holes. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous orebodies of the porphyry-copper type would be the most likely candidate for application of the technique. Discontinuous orebodies would not be amenable to this technique. The method is based on the measurement of the linear correlation between the spatial distribution of two sets of data. The Pearson product-moment correlation coefficient is used. This is a standard statistic commonly used to measure linear correlation between two sets of data. The statistical significance of the correlation coefficient at a 95% confidence level is the main criterion for controlling the project. For purposes of reference we will call our technique the "correlation method" in this paper.

Jan 1, 1971

By M. J. Nicol

The leaching of gold with thiosulfate solutions in the absence of ammonia and copper ions was investigated using electrochemical and kinetic methods. In sodium thiosulfate solutions, the electrochemical oxidation of gold was hindered and the leaching rate using pure oxygen as the oxidant was very slow. It was found that the addition of a small amount of thiourea or formamidine disulfide to the thiosulfate solution greatly enhanced the oxidation of gold. However, the enhancement to the overall dissolution of gold using dissolved oxygen as the oxidant was limited. This was attributed to the fact that the oxygen reduction process was unaffected by the additives and remained slow, which limited further improvement to the overall kinetics. An alternative oxidant, the ferric EDTA complex having a reduction potential of approximately 0.12 V, was found to be promising. The cathodic reduction of ferric EDTA was fast and reversible at neutral pH. While the ferric EDTA complex was effective in oxidizing gold, it did not appear to significantly oxidize thiosulfate. A thiosulfate solution containing thiourea and ferric EDTA has been shown to quickly dissolve gold in the form of a powder as well as from gold ores. In the leaching with the ores high gold recoveries of above 90% was achieved with the best performance obtained in neutral solutions (pH 6-7).

Jan 1, 2005

The status of remote sensing data availability in New Zealand is outlined and discussed. Currently, two multispectral remote sensing satellites are providing regular data over New Zealand; aircraft scanner services are available from Australia.; operational radar satellite services are yet to materialise. The advantages and disadvantages of the various data types are compared and contrasted. Some image processing considerations are outlined.

Jan 1, 1993

By Botao Lin, Yan Jin, Hongjuan You, Jingjun Pan, Huiwen Pang, Mian Chen, Sen Chen

"Steam Assisted Gravity Drainage (SAGD) has become the mainstream technology for ultra-heavy oil recovery in Xinjiang oilfield, the success of which depends heavily on shortening of preheating period as well as forming homogeneous and highly permeable zone in land-facies oilsands layer. Towards this aim a special hydraulic fracturing process is required, which is accomplished through controlled water injection to a pair of horizontal wells in order to create homogenously distributed microcracks in the zone between the two wells. The associated mechanical response, however, is unclear for land-facies Karamay oilsands that is loose in texture. In this regard, this research utilizes a triaxial test system on cylindrical specimens extracted from field-collected oilsands cores. Isotropically consolidated drained triaxial compression tests are conducted on both saturated and unsaturated specimens so as to investigate the mechanical response of oilsands at different spots relative to the wellbore. Moreover, acoustic emission and fast pulse-decay permeability are performed to monitor fracture development and permeability evolution. Based on these experimental studies, the mechanism of dilation in oilsands is comprehensively analyzed. The findings reveal distinctive behavior between the saturated and unsaturated specimens as respect to dilation, porosity/volumetric evolution and change of permeability. It is also found that shear bands can be created upon shearing on triaxial specimens, rendering porosity or volumetric strain the factor that is more proper for evaluation of stimulation efficiency in the field.INTRODUCTIONXinjiang oilfield is widely known for its abundant deposit of heavy and ultra-heavy oil that has been estimated to be several hundred million tons. The ultra-heavy oil deposit located in Fengcheng region of Karamay at the northwestern part of the Junggar Basin, Xinjiang, China, has over 360 million tons of resource (Yuan et al. 2013). The resource is deposited in depths from 180 to 450 m and has viscosity over 100, 000 mPa•s at a temperature of 50ºC, bringing technical challenges to recovery activities."

Jan 1, 2015