Search Documents

By John L. Watson

The dewatering of steel industry waste sludges prior to discard or recycling often presents significant problems due to the fineness of the sludge particles, which may blind the filter medium and/or produce a cake with limited porosity, Several steel plant wastes, such as sludges from BOF and EAF gas cleaning operations exhibit not only a very fine particle size, but also some degree of magnetic character, A novel process has been developed to utilize the magnetic character of such sludges to enhance dewatering through a multi-force operation involving magnetic, chemical and vacuum forces, The process consists essentially of undertaking vacuum filtration of a flocculated sludge in a magnetic field, This is achieved by installing a permanent magnetic in a fixed position on the axis of a vacuum drum filter, thus effecting filtration of magnetic and non- magnetic particles, bound together in flocs, in a magnetic field, Previous tests using a modified laboratory vacuum drum filter treating artificial (magnetite) and industry waste (BF sludge) feeds have demonstrated that filtration capacity may be enhanced significantly with increases of up to 3000/0, An explanation of the mechanisms associated with the enhanced filtration was not obvious, and this research was undertaken to permit the cake formation in the magnetic field to be monitored to provide an insight into the manner in which particles agglomerate to form the cake. These tests revealed that the magnetic field caused magnetic particles to be aligned perpendicular to the filter surface and to form channels through which filtrate could freely pass thus increasing capacity, The effects of various magnetic fields and field strengths on the filtration process were also investigated. A simple computer model was constructed to demonstrate the proposed theory of multi-force dewatering, The model output graphically illustrated the suggested mechanism and confirmed the enhanced capacity of the novel dewatering process,

Jan 1, 1996

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By David A. Newman

In the 1950s, an underground limestone mine in the Camp Nelson Formation was developed from an outcrop exposure. The Camp Nelson Limestone met the requirements for DOT stone and aggregate. The mine ownership changed several times, which resulted in distinct mine designs in Level 1. Based upon the production requirements and an attempt to maximize limestone recovery from a single level, a variety of pillar dimensions and three mining heights (28 feet, 68 feet and 83 feet) were developed. This was sufficient prior to reaching the mineable extent of Level 1. Level 2 introduced previously unknown ground control challenges. These included: ??Pillar spalling and a significant back fall on the Level 1 - Level 2 decline; ??Laminated immediate back and the need to bolt the back on Level 2; ??Delamination of the back adjacent to the Level 1 - Level 2 decline resulting in bolt shearing, and floor heave in isolated areas of Level 2; ??Multiple level interaction, the need to design pillars based upon numerical modeling as columnization between Levels is infeasible: and ??Water inflow as the mine approached river. To meet the challenges, a testing program to determine rock strength and physical properties was implemented along with numerical (LAMODEL and FEM) modeling, and borescope inspections of the immediate back. The efforts to implement rock mechanics were re-focused as Level 2 approached its mineable limit and the initial attempt to drive a decline to Level 3 was unsuccessful. A second decline site was selected based on inter burden stability, a consistent shale parting for the Level 3 back horizon, results from numerical models of the immediate back and multiple level interactions, and the projected low water inflow. The mine is operating on Levels 2 and 3 with long-term planning and ground monitoring for Level 3.

Jan 1, 2014

By Takeo Fujino, Nobuaki Sato, Junichi Hasegawa, Masato Nakazawa, Kohta Yamada

"Tantalum oxide thin films were deposited on quartz substrates by laser ablation of Ta2O5 target using Nd:YAG pulse laser. Deposition-was observed when a laser light energy higher than 200 mJ and its repetition rate higher than 3 Hz. A thin film of 0.1 µm thickness was obtained by the ablation using a laser light of 300 mJ and 6 Hz for 2 sec. The thickness of the film increased with increasing energy, repetition rate and irradiation time of laser. By the SEM observation, it was found that many island-like particles were deposited on quartz substrate forming a thin film. The obtained thin film, which was identified as ? Ta-O by X-ray diffraction, was oxidized to Ta2O5 by the heat treatment in air at I273 K for 3 h.IntroductionTransition metal oxides have a potential to show special characteristics in electrical, magnetic and/or optical properties. When such compounds are fabricated in the form of thin film, the special properties would be improved or new characters would appear in comparison with bulk materials. Tantalum penta-oxide is widely used as a capacitor since Ta2O5 shows high dielectric constants up to high temperatures. The tantalum solid capacitor has been fabricated by the electrical oxidation of sintered Ta metal cylinder followed by MnO2 film coating. However, further improvements, reduction and layered structure formation, are required for compacting the devices. The layered structure of thin films would be applicable for the above requirements. The formation ofTa2O5 film by low pressure CVD1), photo CVD2) and magnetron sputtering3l were reported. The laser ablation -method is one of the most convenient techniques for the deposition of thin films from their compounds, such as oxides. Formation of Ta2O5 film by pulse laser deposition (PLD) method using ArF excimer4), Nd:YAG (533nm)5) and TEA CO2 6 lasers was reported. In these PLD studies, ablation was carried out in relatively high oxygen pressures resulting in formation of Ta2O 5 film. In this paper, the deposition of tantalum oxide thin film by the laser ablation of Ta2O 5 using Nd:YAG pulse laser was examined at a viliety oxygen pressures ranging from 10-8 to 10 Torr. The morphology of the films was also investigated in relation with substrate temperature and oxygen pressure."

Jan 1, 2000

Since March 28, domestic producer prices on 99.5 percent aluminum ingot have been at 5l¢ per pound. Dealers in this same time frame have held ingot quotes at 49¢-50.5¢ per pound. COBALT: Imports from southern Africa in 1976 constituted 73 percent of total cobalt imports. Moreover, the United States is 98 percent dependent on imports of cobalt. For this reason, the Bureau of Mines is closely monitoring developments abroad to ensure an advance notice of any possibility of a shortfall in supply. Included in these imports were those from Zaire (41 percent directly from Zaire and 15 percent via Belgium-Luxembourg), Zambia (11 percent), and Botswana (6 percent). Also being closely watched are industry stocks.

Jan 1, 1977

By Wade E. Cooper

INTRODUCTION How accurate are past and present employee radondaughter exposure records of underground uranium miners employed in the United States? This often-debated question is essential for future substantiation of safe exposure limits. An apparent discrepancy between company-reported exposures and Mining Enforcement and Safety Administration (MESA) projected exposures was detected in 1977. For these reasons a need for an updated comparison of these exposure data was indicated. This paper gives some of the conclusions of the earlier study and compares more recent exposure records compiled by the Atomic Industrial Forum, Inc., with projected exposures based on sampling by Federal mine inspectors. EARLIER STUDY In its 1977 Annual Report (U.S. Department of the Interior, 1978), MSHA's predecessor, the Mining Enforcement and Safety Administration (MESA), reported that there was "an apparent discrepancy between Federal inspection results and company records." Both company records and MESA's projections from samples taken during routine Federal inspections indicated reductions in the average exposure of underground uranium miners from 1975 to 1977, but the MESA projections were over 4 times higher than the company-reported averages. This apparent discrepancy however, was based on a comparison of exposure data reported for all U.S. underground uranium miners. This projection more closely represented the average exposure of U.S. underground uranium mine production workers who worked 1,500 hours or more during the year. Exposures of such workers are reported each year by the Atomic Industrial Forum, Inc. (AIF) in summaries of exposure data reported to the AIF by uranium mining companies throughout the United States. (The AIF exposure summary for 1979 appears as tables A-1 and A-2 in the appendix of this paper.) Assuming that the average exposure for each exposure range category is the midpoint of each exposure range category, table 1 compares the estimated average exposures for U.S. underground uranium mine production workers who worked underground 1,500 hours or more each year in 1975 through 1977 with the exposures projected by MESA for those years. [Table 1. - Average Exposure and Projected Average Exposure for U.S. Underground Mine Production Workers Who Worked Underground 1,500 Hours or More During the Year. Company, MESA?' Reported- Projected Year (WLM) (WLM) 1975 1.59 5.68 1976 1.84 4.64 1977 1.68 4.08 1 Atomic Industrial Forum, 1976, 1977, 1978. 2 U.S. Dept. of the Interior, 1978.] Table 1 indicates that, even after adjustment to ensure better comparability an apparent discrepancy between Federal inspection results and company reported exposures for 1975-1977 exists; however, the apparent discrepancy diminished over the 3 years. Slade, 1977, explained some of the discrepancy between company records and MESA projections of miners' average radon-daughter exposures as follows: 1) Concentrations of radon daughters in some work areas can vary greatly during any one day. A variation from 0.3 WL to 17.0 WL has been measured in the same stope on the same day. 2) Seemingly simple abatement problems indicated by the regular Federal and State inspections were solved simply by manipulating the mine ventilation. 3) The methods used by mine operators to compute cumulative exposures were such that high radiation readings were seldom or never reflected in the records. For example, a work area sampled on Monday indicated a radon-daughter level equal to 0.2 WL and this was recorded. It was sampled again on Wednesday of the following week and the level was 2.2 WL. The miners were withdrawn or told to fix the ventilation, and when this was accomplished the area was sampled and found to be at 0.2 WL again. Although the miners could have been working in the higher concentration up to 6 days, this reading might never be reflected in their records. If it was recorded, only a fraction of the day on which it was discovered would be entered into the cumulative exposure calculation (time-weighted average). 4) Some of the mines visited used a mine average radiation concentration, and every employee working underground was given the same exposure per unit of time spent underground. As a result of the 1977 study, more stringent sampling and recordkeeping standards were proposed and public hearings held in 1977. The resulting new and revised health standards on radon-daughter sampling and exposure recordkeeping became effective August 30, 1979 (Mine Safety and Health Administration, 1979). Prior to these new regulations, radondaughter sampling requirements were on an "as often as necessary" basis (Code of Federal Regulations, 1978). The new regulations required practically all active work areas in underground mines to be sampled at least once every 2 weeks, with many areas requiring weekly sampling. They also required calendar-year exposure records of all underground

Jan 1, 1981

By Nicholas Adrian Barcza

"What affects and influences one’s perspective of the mining and metallurgical industries?One’s perspective of the industry we work in changes over time as a function of our experience as well as from the interaction we have with colleagues locally and probably even more so with those internationally. Furthermore, the ever-changing environment continues to impact the context in which one sees things. Living mostly in South Africa through its changes in the past fi fty years but also having the opportunity to travel extensively and work on projects abroad adds an invaluable richness to this more global perspective. One of the greatest challenges is how best to use this experience to endeavour to support the many potential opportunities in southern as well as sub-Saharan Africa. However, one has also to face the realities of how the best interests of the country and its peoples are sadly often not well served for various unfortunate reasons. Investment, education, regional stability, and good governance are some of the most critical considerations for the prosperity and survival of the region.The mining and metallurgical industry in southern and sub-Saharan Africa changed significantly during the post-colonial and apartheid eras as a result of global and regional developments that have impacted the ownership of businesses, the technologies used, and products produced in a manner that was not envisaged even fi fty years ago. Southern Africa’s mining and metallurgical industry has progressed from one based mostly on diamonds and gold in the late 19th century to a much more diverse one that involves the production of a variety of other precious, base, and ferrous metals and minerals as well as coal and industrial minerals. The infrastructure and manufacturing capacity was largely developed to meet the needs of this industry during its growth phases, but even though the dynamics have changed there is still a need for more efficient and effective support systems in the region."

Jul 1, 2019

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By A E. Annels, M NoppT

Ore Reserves are key mining company assets and their reliable estimation is crucial for both feasibility studies and the day to day operation of a mine. The reserve is based on the Mineral Resource after the application of certain technical and economic parameters. Engineering aspects of reserve estimation can be accurately determined to ¦10 per cent, however the majority of project risk will revolve around the resource. A final Ore Reserve generally contains a set of figures quoted without reference to its potential errors. Rarely are overall confidence limits quoted and, if they are, they often do not take into account many of the factors that cause uncertainty in the grade and tonnage estimates. There is thus an unquantifiable risk, which the operator should be aware of. This paper presents a review of the possible sources of error that might occur during the various phases of an exploration and estimation programme which are carried through into the Ore Reserve and hence mine design.

Jan 1, 2002

By Xiaojian Zuo, Yihua Han, Qingguo Xue, Jingsong Wang, Lintao Wang, Rongzong Lan

"Using the facility of reduction experiment, the low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace (OBF) were studied. Through analyzing the results, the difference of pulverization and reduction behavior of sinter in OBF and conventional blast furnace (BF) were discussed. Furthermore, the effect laws of reduction temperature and the content of CO and H2 on reduction behavior of sinter were studied. Also the controlling step of iron oxide reduction was discussed. Compared with BF, the low temperature reduction pulverization of sinter became serious at 773 K; reduction rate became faster at 1173 K; reduction time became less and final reduction degree was increased in OBF. With increasing of H2 and CO contents, the reduction of sinter was promoted. The reduction process was controlled by interface chemical reaction at the earlier stage and by interface chemical reaction and internal diffusion at the final stage.IntroductionThe new ironmaking technology of Oxygen Blast Furnace (OBF) is most likely to be used in large-scale application process. The concept relies on the removal of the CO2 contained in the top gas of the blast furnace. Therefore the useful components, i.e. CO+H2, can be recycled back into the furnace and reused as reducing agents. In addition, injecting oxygen (O2) into the furnace instead of preheated air, removes unwanted nitrogen (N2) from the gas. Under the pressure of CO2 emissions in iron and steel making, the growing international shortage of coking coal resources and the rising price of coke, OBF has attracted attentions of both domestic and foreign researchers, because it has so many advantages such as high productivity, high PCI rate, low coke rate, high gas reducing capability and high top gas calorific value, etc [1-7]. As a result of recycling most of the top gas after CO2 removal and injecting oxygen into the furnace, the reduction capacity of blast furnace gas will be increased, so the metallurgical behavior of OBF's iron burden is different from traditional blast furnace. Therefore, it is one of the keys to develop this technology, which studies the metallurgical behavior of sinter in OBF. The purpose of this paper is to study the low temperature reduction pulverization and reduction behavior of sinter at the atmosphere of OBF, which includes the difference of low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace and conventional Blast Furnace (BF). It will provide theoretical basis for the development of OBF."

Jan 1, 2012

By G Nicholas, S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

"A new approach to mineral project evaluation is described called Scenario-Based Project Evaluation (SBPE). SBPE incorporates well established æscenario planningÆ and æscenario thinkingÆ approaches, which are used extensively in other industries,?most notably the?petroleum industry. While most scenario planning is qualitative and non-probabilistic, the approach described here includes both quantitative and qualitative aspects. SBPE is complementary to optimisation approaches and allows mining firms to build and operate projects that are more robust in the face of adverse changes as well as proactively respond and exploit the upside offered by a realistic assessment of variability. The approach has potential to improve project performance and decrease operational risk. It also has important applications for currently operating mines.Conventional evaluation of metalliferous mineral deposits uses estimates of metal grades and deleterious attributes in singular æorebody modelsÆ, usually 3D block models, which fail to capture two critical aspects that underpin the realised value of mining projects: the inherent uncertainty of the estimated attributes the spatial variability of attributes, at the scale of mining selection, which impact on downstream processing steps and fundamentally drive realised value. While singular models are appropriate for estimating block averages, conditional simulation (CS) models of the relevant attributes are needed to represent uncertainty and capture spatial variability. Any attributes that can be either built into CS models and/or modelled in the envisaged mining/processing steps, can be evaluated fully through to highly ægranularÆ (ie detailed and un-smoothed) cash flows. A complete view of SBPE relies on selected strategies being tested against plausible æscenariosÆ of factors external to the project and thus outside management control. æExternalitiesÆ captured in such scenarios include market prices, costs and taxes. Via SBPE, project managers may demonstrate that there is material value in preserving or purchasing options that provide future flexibility to respond to the changing externalities or changes in orebody performance. Such flexibility generally comes at a cost but is very difficult to value. It is argued that full value chain evaluation using SBPE can help to value these options for a mining company. A case study for a gold mine is presented.CITATION:Vann, J, Jackson, S, Bye, A, Coward, S, Moayer, S, Nicholas, G and Wolff, R, 2012. Scenario thinking - A powerful tool for strategic planning and evaluation of mining projects and operations, in Proceedings Project Evaluation 2012, pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By M. G. Benz, J. F. Elliott

The austenite solidus of the iron-carbon system has been determined using a series of diffusion couples, each of which consisted of a specimen of austenite held in contact with a melt saturated with austenite. After the equilibrium distribution of carbon had been established by diffusion at a specified temperature, i.e. the austenite specimen had become austenite of the solidus conzposition, the diffusion couple was cooled, sectioned and anazlyzed for carbon. The solidus was found to be a straight line: A revised iron-carbon temperature-composition diagram is presented, COMPOSITION has a marked effect on the temperature at which austenite begins to melt and the austenite solidus of the iron-carbon system describing this effect has been the subject of many investigations.1-10 The significant results of these investigations are presented in Fig. 1. The experimental methods and purity of the materials used in them are summarized in Table I. In plotting the data in Fig. 1 no attempt has been made to convert these results to the International Temperature Scale of 1948," except for the data of Adcock,5 as this conversion would do little to reduce the uncertainty that exists as to the position and shape of the solidus. A point of major concern in evaluating these data is that the alloys studied, except those used by Adcock, were not binary alloys of iron and carbon, Table I. Also, it would appear that several of the methods did not permit equilibrium to be established through the system being studied. All that can be said for the results of these investigations is that they indicate only approximately the location of the solidus with the uncertainty as to its location at 1 pct C being approximately 100°C. The current investigation was undertaken to provide reliable data by which the austenite solidus could be established. It was hoped that information on the liquidus also could be developed at the same time, but experimental limitations prevented this as austenite segregated from the liquid on cooling. After a careful study of possible experimental methods and extensive laboratory tests, it was decided that the use of a series of austenite-liquid diffusion couples would provide the most reliable results. This paper describes the method and its results and also includes a complete iron-carbon temperature-composition diagram based on what are considered to be the best available data. EXPERTMENTAL METHOD The diffusion couple used for this investigation consisted of a small cylindrical pellet of austenite held in contact, at a specified temperature, with a melt saturated with austenite. The composition of the cylindrical austenite pellet was chosen to be approximately 0.1 wt pct C less than the estimated

Jan 1, 1962

By E. J. Harris

Data obtained from mine ventilation pressure and quantity surveys are required to accurately diagnose ventilation problems, project future air quantity needs, and to locate conditions adversely affecting the efficiency of a mine ventilation system. A method for making mine ventilation pressure surveys with aneroid altimeters was presented in Bureau of Mines Information Circular 7809, and a description of field calculation technique is presented. This report supplements Information Circular 7809 by developing the information obtained during a mine ventilation pressure survey into a single equation suitable, with appropriate modification, for use with desk-top calculators and digital computers. The equation can be used to calculate the ventilation pres sure from the base station to any underground station, or between any two underground stations, and can be programed for semiautomatic sequential calculation using a desk-top calculator. An example of application to a programed desk-top calculator is provided in the appendix.

Jan 1, 1973

By G. Nino de Guzman, L. C. Woollacott

The isotherms that are usually taken to represent the force 'driving' the adsorption in carbon-in-pulp processes may change from contactor to contactor. This paper reports on an investigation into the extent to which this Isotherm shift is Influenced by the changes in oxygen and cyanide concentration that occur in operating plants. The impact of the isotherm shift on the reliability of simulation results is examined.

Jan 1, 1993

The Broken Hill orebody ,occurs in the Willyama Complex, a block of Precambrian rocks which have been strongly folded and metamorphosed at moderate to high grade. Although -the origin of the silver-lead-zinc mineralization remains obscure, recent investigations have substantiated the view that the orebody has undergone concomitant high grade metamorphism with the enclosing wallrocks. The mesoscopic structures produced by this metamorphism are described, and the possible processes Telating to their formation are disoussed.In the high grade ore, metamorphic structures which can be recognized are foliation and lineation, wallrock fragments, layering, flow folds, ore breccias, and sulphide bearing veins. These structures can be related to processes involving plastic flow and fluid phase transport of the mineral assemblage. 'In areas of low grade mineralization adjacent to high grade ore, the structures more closely resemble those produced in -the wallrocks-foliatlon, lineation, layering, folds, and sulphide injections. Within areas of high grade ore, lenses and pods of manganese silicates Probably represent original inhomogeneities in the ore, i.e., portions of manganese-rich and sulphide deficient rock which have been metamorphosed to manganese silicates.From the structures displayed, a sequence of events has been established for the plastic flow of ore during deformation.

Jan 1, 1975

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Arístides Sotomayor

El presente texto señala la importancia del oro a nivel financiero y minero ya que los inversionistas suelen utilizar este metal para obtener ganancias debido al mínimo riesgo existente en la pérdida de su valor comparado con otras divisas. Así, se estima que en el Perú, existen 480 unidades mineras de oro, de las cuales 28 concentran cerca del 90% de la producción nacional, como la Minera Yanacocha, Minera Barrick, Compañía de Minas Buenaventura, Consorcio Minero Horizonte, Aruntani y Aurífera Retamas. Entre las dos regiones que producen mayor cantidad de oro está: Cajamarca y La Libertad ( 38%) y la tercera región es Arequipa, seguida por Madre de Dios (9%).

May 1, 2016

By H. F. Easter

The lead department of the El Paso Smelting Works at El Paso, Tex., is operated strictly on a custom basis. The ores treated are drawn from the surrounding territory, comprising New Mexico, Arizona, western Texas, and northern Mexico. Ores received from the last-named section originally amounted to a very large tonnage, but. of recent years have dwindled into comparative insignificance so far as this plant is concerned. This has been due partly to the establishment of a lead-smelting plant at Chihuahua, which is much closer than El Paso to most of the important mines, and partly to the recent revolutionary troubles in Mexico. There are no mines of either lcad or copper in the immediate vicinity of El Paso. In general, it may be said that the lead-ore supply of recent years has been uncertain and precarious, with a general tendency toward an excess of silica and a shortage of iron. This latter requirement has been met in large part by the use in El Paso lead furnaces of considerable amounts of roasted leady copper matte from the Chihuahua smeltery and of converter slag from the El Paso converters. These two materials, coupled with complex lead-copper ores from Bisbee, Ariz., have introduced into the lead-smelting operations a most unusual amount of copper, which has had an important bearing upon the smelting practice of the plant. his matter will be discussed later. The ore, loaded in either box cars or gondolas, enters the storage yard on four tracks elevated about 8 ft. above the ground. As all unloading is done by hand, unloading platforms at the height of the car floor parallel the tracks on each side to afford a runway for wheelbarrows. At frequent intervals these lengthwise platforms are joined together by others running crosswise to facilitate the distribution of the ores evenly over the beds, which are located below and between the tracks. At present much of the bedding space formerly used for lead ores is given over to the copper department, but 20 bins of various sizes are retained for the use of the lead furnaces and the Huntington & Heberlein roasting plant. The largest of these holds about 1,000 tons, while the smallest holds not over

Jan 1, 1916

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By Susanne Pignolet-Brandom

Reflected light microscopy scanning electron microscope energy dispersive spectroscopic analysis and backscatter electron image and electron microprobe chemical analysis have been used to study lead sinter and lead blast furnace slag. These studies provide invaluable information on the phases present their intergrowths, and their chemical composition. Such information increases the understanding of the nature of pyrometallurgical processes and the behavior of minor elements during these metallurgical processes.

Jan 1, 1987