Search Documents

By Clarence P. Linville

In an article published in the Iron Trade Review,' I gave a convenient arrangement for the installation of wet and dry bulb thermometers for use in making moisture determinations in the air being blown into a blast furnace, and also gave a chart for use in obtaining moisture values from the thermometer readings. The data from which this chart was prepared were obtained from the tables in use by the U. S. Weather Bureau.2 The work of Carrier3 has shown that these tables are somewhat in error. He has recalculated the values for moisture as referred to wet and dry bulb thermometer readings, and he has prepared a psychrometric chart from the values thus obtained. This work has placed the subject of psychrometry upon a correct scientific basis. I think it is proper that we should recognize the importance of his work and give him credit for one of the most interesting and valuable researches that have been published in recent years. Blast-furnace men are not ready to use, as he suggests14 a value expressed in grains of water accompanying a pound of dry air. However convenient this may be for heating and ventilating work and other engineering problems, there are several reasons for preferring the use of a value expressed in grains of water in a cubic foot of mixed air and water vapor, in connection with combustion phenomena and the effects of moisture on blast-furnace operation. Previous papers presented to the Institute have used such values and we have

Jan 1, 1914

By L. J. Kane

Several processes being developed by the Federal Bureau of Mines to provide new and more efficient uses for coal require practical methods for removing dust from hot gases. Filters provide such means. The efficiency of filters made of aluminum silicate fibers and porous stainless steel was determined. The results obtained with the fibers were previously reported.5 In this investigation tests were made with three porosities of stainless steel filter material (grades C, D, and E) at a gas flow of 1,000 std. c.f.h./sq. ft. of filter, temperatures of 75° and 1,000° F., and dust loadings (as represented by cumulative dust fed) of 100, 1,000, and 10,000 gr./sq. ft. of filter. Pressure drop during the runs ranged from 0.1 to 21 in. of mercury, and dust removal from 25 to 99.93 pct. Filters having the finest pores gave the greatest pressure drop and percentage of dust removal; however, their dust-holding capacity was slightly lower. Usually, their ability to remove a higher percentage of dust at the same pressure drop more than compensated for the slightly lower dust-holding capacity. With increase in temperature, for the same weight rate of flow of gas, the pressure drop increased and the percentage of dust removal decreased. The effect of temperature was probably due to the accompanying change in the linear velocity and viscosity of the gas.

Jan 1, 1961

T.P. 1958 D. H. DAVIS.*-Mr. Carris has ably pre¬sented the problems of coal preparation, particularly those brought about as the result of increased mechanical loading. Many mines are now crushing the run-of¬-mine raw coal through 12 or 15 in. immediately after it is dumped from the mine car and before it is handled by conveyors. At certain mines the removal of large slate mechanically has been solved by the installation of scalping screens consisting of bars or rails set at spacing of 12 to 15 in. on the top deck of the main raw-coal sizing screen. At the plants where these are in use, the plus 12 or I5-in. raw material contains 60 per cent or more free rock or slate, so that it is easier to pick coal than to pick rock. After the screening at 12 or 15 in. is accomplished, the oversize material is diverted to one side of the shaker, where a picker allows the refuse to pass off the shaker into a chute and guides the coal back onto the shaker. After the large rock has been removed, it is then advisable to reduce the size of rock by crushing before putting it onto a conveyor. A great saving in picking labor has been made by the use of such scalping screens, which in addition has maintained the plant capacity when handling a dirtier feed. The great increase in percentage of coal under 1/4 or 3/8 in., coupled with a greatly increased percentage of free impurities in this size, is the most serious problem that has been brought about by mechaniced loading. Many plants that formerly prepared good quality 1/4-in. to o or 3/8-in. to 0 slack by air¬cleaning are faced with installing facilities for wet-cleaning mechanical and heat-drying and water clarification. The change to wet prepa¬ration of fines usually affects the marketing problems for many coal companies. There will also be problems involving wastage of fine solids and stream pollution. Much work will be necessary for improvements in present practice. Pneumatic and electrostatic methods for cleaning fine coal should receive consider¬able attention in an attempt to avoid wet¬cleaning of fines. The preparation supervisor and the plant personnel should not be satisfied merely to run the cleaning-plant machinery and assume that the job will be done for them. Coal is a heterogeneous substance and in many instances is constantly changing. This is more true when full-seam methods are in use. Only persons trained to observe closely and make the necessary changes in plant operation will be able to solve the many problems that will be imposed on the preparation plants. The plants will require skillful and observant operating men. With full-seam mining methods, seams of roof coal will often be mined. Under the former mining systems these strata were not mined and frequently they contain a high per¬centage of bony and banded partings. The mining of this coal will greatly alter the washability and specific gravity characteristics of the feed to the plant. Often the percentage of 1.40 to 1.60 sp. gr. increased from 3.5 to 7.5 per cent, or nearly a 1.0 per cent increase in the ash content of the 1.60 sp. gr. float coal. Thus the cleaning problem is much more difficult, and it is unlikely the same ash content of cleaned coal can be produced as before without a decrease in recovery or the produc¬tion of a "middlings" product. Mr. Carris had this in mind when he said "The quality of the

Jan 1, 1946

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By V S. Mutton, M J. Shearer

"The current economic challenges faced by the mining industry led to a review of options for reducing the cost of ventilation control devices (VCDs). The VCDs at the Mount Isa Mines site operated by Glencore in Queensland typically experienced significant damage on the operating levels and required expensive replacements. Ventilation controls can become damaged by the effects of stope firings. This paper discusses the nature of blast wave effects, giving consideration to distance from the firing and changes in mine geometry. The time taken to adjust the airflow on the operating levels with the current VCDs resulted in the loss of productivity opportunities. The mine site engaged an equipment supplier to collaborate on the development of a high-strength regulator to control the required airflows within its underground workings.The strengthened regulator proved to be cost-effective and provided additional benefits, including ease of use, simplicity of installation and speed of change in the control of available ventilating airflow. An added advantage of the re-engineered regulator compared to contemporary VCDs is its flexibility, which includes the ability to easily move mobile equipment into different ventilation districts where required without the need to remove the VCD from its location. This paper describes both the innovation and environmental sustainability approaches followed when developing the new regulator for its implementation at the site.CITATION:Shearer, M J and Mutton, V S, 2015. Advanced ventilation control – an analysis of innovation and environmental sustainability, in Proceedings The Australian Mine Ventilation Conference, pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By Harry Littleton, Jr. Scarber, Wanliang Sun

"The Lost Foam Casting (LFC) process is relatively immature when compared to other casting processes. To make the process more robust, computer modeling is needed to reduce lead times and casting defects. In this study, metal filling of lost foam aluminum castings was visualized using state-of-art real time X-Ray technology. Metal filling of the lost foam casting was simulated using a commercial software package. The result of the computer simulation was compared with the results of the real time X-Ray visualization. Some of the computer simulation results agreed with the real time X-Ray visualization, but some did not. Based on other studies using real time X-Ray technology, new input variables, such as foam density variations, were developed for the computer modeling. With the new variables, modeling of the lost foam casting process becomes more realistic. IntroductionMold filling of the Lost Foam Casting (LFC) process is an important step toward making a quality part. In the LFC process, molten metal is poured against a refractory coated foam pattern surrounded by dry sand. At the pouring temperature of aluminum, the foam pattern is decomposed into 30% (wt) gaseous and 70% (wt) liquid foam pyrolysis products. Existence of the gaseous foam decomposition products significantly increases the back pressure on the metal stream compared with the conventional open cavity sand mold. Entrapment of the liquid pyrolysis products during the metal filling generates many casting defects, such as internal pores, fold and blisters. Existence of these casting defects sometimes seriously degrades the quality of the components manufactured by the LFC process. Understanding and controlling the metal filling of the LFC process will certainly make this process more robust."

Jan 1, 2004

Ferric (Fe3+) ions are omnipresent in flotation circuits. Depending on pH and the nature of the ore body, Fe3+ ions may play a role in the adsorption of thiol collectors on sulfide minerals. To investigate this possibility, a two-compartment galvanic coupling cell was designed. This cell was used to monitor changes in contact angle of a sulfide mineral in one compartment, while varying concentrations of the Fe3+ ions in the other. The results showed that Fe3+ ions promote xanthate adsorption as indicated by the increase in contact angle. Implications of this finding in sulfide mineral flotation in general will be discussed.

Jan 1, 1998

By G. W. Jones

[A survey of the Ii terature reJ.l....ting to iE;li tion temperatures of acet-ylene-air and acetylene-oxygen mixtures reveals rather '.'fide disagreement in the reported results. In SO!':1e instances the i ition temperatures of acet?-ylene-air mixtures were reported to be lower than those of acetylene-oTjgan mixtlU'es, which is contrary to experience 'tri th other combustibles. ':10 clea.r up some of t!le reported discrepancies, the authorn have icvestigated the igni tion temperatures of acetylene both in air anri oxygen, and their results are presented in this report.]

Jan 1, 1941

By Wayne D. Gould

Planning for a project does not start with the announcement of the approval for a project. Planning actually begins when the project is only a prospect and it involves the years of experience of many people because their expertise influences the final decisions. In partial anticipation of the Pinto Valley project, as well as a search for improvement in the Copper Cities operation, two projects were undertaken. The first project was to substitute one 26" cyclone for three 20? cyclones in the single stage grinding circuit. The second project was to replace the Hunt air flotation cells with 300 cubic foot mechanical cells. The 300 cubic foot cells were just being introduced, consequently two types of cells were selected for testing. The results from both projects influenced the decisions on equipment for the Pinto Valley project.

Jan 1, 1975

By J. W. G. Hannon

FOLLOWING the experimental work of Denny, Robson, and Irwin, and the clinical investigation by Crombie and Blaisdell, an investigation of aluminium therapy was begun at Washington, Pa., which is situated in a very large industrial section of the State. Some of the men to be studied were from plants manufacturing silica brick, refractories used in steel and glass manufacturing, and semi-porcelain table-ware; others were workers in foundries, sand blasters, and men engaged in the quarrying of ganister rock. This group of workmen gave an opportunity to study the effects of aluminium on various types of silicosis which differed somewhat from that found in hard-rock miners. EXPOSURE In their occupations, the men studied were exposed to silica dust concentrations ranging from 17 to 97 per cent free silica. In the silica brick industries, the unfired product averages 96 per cent silica in the form of quartz, whereas the fired brick contains 50 to 62 per cent cristobalite plus 17 to 30 per cent tridymite, forms of silica that, on account of their higher solubility, are more toxic than quartz. The operational dust counts in the plants varied from 15 to 9,500 particles per c.c., and the median particle size from the aerial samples was 1.0 micron for the green product and 2.0 microns for the fired product. The length of exposure varied with the occupation as well as with the individual plant, but disabling silicosis could be produced in less than four years in certain exposures. The average time needed to produce radiological silicosis in those susceptible to this disease was eight years. Some of the men in our series of cases have been treated as long as fifteen years after exposure had ceased, and have improved under treatment.

Jan 1, 1944

By Shu Xinqian, Zhou Weining, Shan Zhiqiang, Feng Jifu

"Modified calcination conditions on the extraction of rubidium resources from muscovite (KAlz[AlSi301o](OH)2) ore are systematically studied. The impact of various factors on the rubidium leaching rate is also analyzed, including the agent types, roasting time, the mass ratio, roasting temperature, etc. The results indicate that the best agent is a combination of sodium chloride and calcium chloride, its mass ratio ofmuscovite/NaCl/CaClz is 1:0.25:0.25. Calcined at 8500 for 30 minutes, the rubidium leaching rate is up to 90%. The reaction of muscovite ore with the chlorinating agent CaC12 has been studied by TG/DSC, the calcined intermediates are identified by XRD, and the surface morphology before and after leaching is characterized by SEM. Rubidium chloride products can be obtained with a purity of 92% by using t-BAMBP extraction, hydrochloric acid reextraction and purification.IntroductionRubidium is one ofrare alkali metals, which is found in 1981 by German R.W. Bunsen and G.R. Kirchhof. Rubidium includes the following features: atomic number is 37, each atom weight 85, the body-centred cubic lattice, each unit cell has two metal atoms, and the density is 1.532g/cm3. The properties of low melting point (312.46 K) and malleability make rubidium have a strong chemical activity and photoemission. Rubidium provides a main material for manufacturing phototube with a wide range oflight waves, which possess high sensitivity and stability. Efforts are being made to carry out research on rubidium ion gngine, magnetic flux generators and thermoelectric transudcer, etc. Rubidium exists in muscovite ore(KA12[AlSh01o](OH)2 (monoclinic system and hexagonal layered structure) as isomorphism and replace the large radius of the potassium atoms, as well as part of rubidium locate between structure layers. The complex components bring great difficulty in comprehensive recycling."

Jan 1, 2013

By I Ritchie, G Lane, C Morley, D Yataco

Marcobre SAC (Marcobre) is developing the Mina Justa project in Peru. The project has a lower grade oxide orebody overlaying the higher grade sulfide orebody. The oxide ore is treated by acid leaching; consumption of acid is high and is managed by vat leaching rather than the more conventional heap leaching process.The leaching process uses ore crushed to 100% passing 8 mm to optimise copper recovery. Acid consumption generally increases with a higher proportion of fines. Marcobre is investigating a three-stage crushing circuit with high pressure grinding rolls (HPGR) in the third stage, instead of the more conventional four-stage cone crushing circuit. The use of HPGR can result in higher fines production due to the higher compression forces in the crushing zone. This paper reports on the outcomes of the test work completed by Marcobre in 2016 and 2017 to manage fines production and compare the use of HPGR with conventional crushing on a high acid consuming ore.At moderate pressing forces, a HPGR crushing circuit appeared to produce similar size distributions to cone crushing. On average, both the copper recovery and the acid consumption in subsequent vat leaching were higher with HPGR crushing than with cone crushing.CITATION:Lane, G, Morley, C, Yataco, D and Ritchie, I, 2017. Are there differences in size distribution when comparing conventional crushing and HPGR?, in Proceedings MetPlant 2017, pp 60–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By L. E. Mylting

Modern ash handling systems exist in considerable numbers and a great deal of design and operating experience has been accumulated, It is the endeavor of this paper to point to a number of frequently recurring problems, A general appreciation of these problems will be helpful in both design and operation of systems. The light fly ash and the heavy bottom ash present different problems, and each will therefore be treated separately. Fly ash is collected in the ducting from the furnace to the stack and beneath the mechanical and electrostatic dust collectors. The greatest amount of dust is collected beneath the mechanicals and electrostatics. Hoppers are generally provided as integral parts of the collector. Suitable valves and piping are connected to these hoppers for removal of the dust. The size and shape of these hoppers are important factors in determining frequency of handling and the capacity of the system.

Jan 1, 1958

By John Nagy

Dust explosion data obtained in laboratory studies by the Bureau of Mines are presented for activated carbon, asphalt, charcoal, carbon black, coal, coke, gilsonite, graphite, lignite, miscellaneous carbons, pitch, tunnel dust, and mixtures of these materials with other ingredients. The explosion hazard is shown to increase as the volatile content of the dusts increases.

Jan 1, 1965

By W. M. Mobley

THE coal industry in Alabama, centered in Birmingham, has pioneered coal-beneficiation practice in the United States. The nature of the coal seams and mining methods employed have necessitated use of equipment and methods best adapted to the local conditions. Although all of the 30 or more coal seams now being mined in the state receive beneficiation, only the three most important producers of coking coals, the Pratt, Mary Lee and Black Creek, are discussed in detail. Nature of the seams, washability characteristics and equipment used are given as examples of the extent of work and progress in this field. The coal seams in Alabama are relatively thin and pitching, making mining difficult and expensive. Most of them are characterized by thin partings of rock or shale in the seam itself, as well as laminations of bone and rash. Mechanical mining methods have increased the occlusions from roof and floor to such an extent that nearly all the coal mined in the state must receive some treatment before it can be put on the market. During the year ending Sept. 30, 1943,1 18,129,792 tons of coal were mined in the state and 14,364,177 tons, or 79.2 per cent, received treatment. Excluding from the total the 1,223,014 tons produced by small wagon mines and the hand-picked lump coal, the amount receiving beneficiation would be more than 90.00 per cent. This is, by far, greater than in any other coal-producing state. The earliest record of coal beneficiation in Alabama was the installation in 1890 of an experimental Lung washer by Alexander Cunningham, for the Sloss Iron and Steel Co. at its blast furnace in Birmingham .2 In 1894 the Jeffrey Manufacturing Co. introduced the English Robinson washer, a combination of a hydraulic classifier and centrifugal machine. Erskine Ramsay, who has contributed so much to the coal industry, saw its possibilities as well as its mechanical defects and soon had his inventive mind at work. He added a sludge tank of his own design, and many Robinson-Ramsay washers were installed in Alabama and other states. The Stewart jig appeared in 1900, followed by the Montgomery jig in 1910 and both have found extensive use. Increased interest in this field led to new designs, such as the American, Elmore; Burke and Faust. The first Baum-type Norton jig was operated in 1930 and within the last five years six large installations of this type have been made by the McNally-Pittsburg, Jeffrey and Link-Belt Companies. Wet-washing tables were introduced in 1922 but not extensively used until recently. The two most popular types are the Deister-Overstrom and Deister Plat-O. The coal-cleaning equipment used in Alabama has been relatively simple, yet efficient, but as the amount of impurities in the raw coal has been increased by mechanical mining and labor costs have become higher, much interest has been shown in sand cones, froth flotation and

Jan 1, 1945

By G W. Wilson, M Aubertin

A desulfurised tailings cover was installed at the Detour Lake Mine in Ontario, Canada, to reduce oxygen penetration into the underlying sulfidic tailings. The cover ranges from one to 1.5 m in thickness and was intended to maintain high water saturation to reduce oxygen diffusion and consume oxygen by oxidation of the residual sulfide minerals. The tailings impoundment was instrumented to measure climatic parameters, water levels and water content profiles within the tailings and single-layer cover. One year of monitoring data was collected. Additional tailings samples were obtained for geotechnical and geochemical characterisation. The average grain size of the cover material was found to be coarser than the underlying tailings. Monitoring also indicated that air entry values of the cover material were lower than the tailings. Numerical modelling was conducted on the cover to predict water content profiles under varying climate conditions together with the depth of oxygen penetration and diffusive oxygen fluxes. Estimates of the diffusion coefficient and kinetic oxidation rates from field data compared well with values obtained by laboratory measurements. Numerical simulations indicate water saturations of less than 85 per cent can be expected under varying climate conditions. Predicted oxygen flux rates through the desulfurised cover over tailings with high acid potential indicate low flux rates reaching these tailings due to either consumption of oxygen by residual sulfur within the cover or saturation of the underlying tailings.

Jan 1, 2003

By AIME AIME

PURSUANT to a recommendation made by the Section delegates at their conference at the Annual Meeting of the A.I.M.E. last February, the Directors, at their meeting on March 15, 1944, appointed a committee charged with the duty of investigating the present status of licensing and registration of engineers, and to make a report on the whole subject for the information of the mining fraternity. The committee consisted of E. W. Ellis, chairman, H. D. Keiser, Henry T. Mudd, J. J. Croston, and Simon Strauss. Messrs. Keiser and Strauss were unable to assist in the work of the committee, and Mr. Mudd was forced to resign in July, his place being taken by A. F. Greaves-Walker. Able assistance was given the committee by T. Keith Legare, executive secretary of the National Council of State Boards of Engineering Examiners, and by Ed. ward Larson, executive secretary of the National Society of Professional Engineers. The accompanying somewhat condensed version of the report of Mr. Ellis's committee, dated Oct. 15, 1944, is confined to facts rather than to recommendations. The "Model Law" to which reference is made was first drafted by repre¬sentatives of six national engineering societies in 1911. It has since been amended many times, the latest version dated June 1943 is recommended to the State Licensing Boards as a pattern for formulating or amending state laws. A copy of the "Model Law" in pamphlet form will be sent to any member on request from A.I.M.E. headquarters while the supply lasts. The report:

Jan 1, 1945

The medical evaluation of the health effects of dust exposure in the mining industry should be based on the premise that the results of the medical examinations will be considered in relation to the previous history of exposure to dust.(l) To this end the Mines Regulation Act and the Regulations under that Act in West- ern Australia provide for: the prime responsibility for dust sampling to rest with the mining companies; the appointment of a Ventilation officer by each mine and the sampling and record- ing by him of dust and toxic gases in work places at three monthly intervals, or more frequently as required; the appointment of a Mines Medical Officer who shall make provision for the medical examination of persons and the prevention of occupational diseases; the appointment of a Ventilation Board, consisting of the State Mining Engineer, the Senior Inspector of Mines for the State, an Inspector of Mines having specialised training in ventilation tech- nology, a medical practitioner having specialised experience in occupational health problems relevant to the mining industry, and a Scientific Officer having duties under the provisions of the Clean Air Act, 1964;

Jan 1, 1979

By Concha F, Sampaio R

In most of the literature, the hydrocyclone is viewed as a black box in which only global variables are present and where the equations are obtained by curve fitting. Recently some work has appeared where the Navier Stokes equations are solved numerically in the hydrocyclone geometry. However, in all of these works the air core surface, which has an important influence on the hydrocyclone dynamical behaviour, is modelled as being a cylindrical surface of fixed radius. In this work, we model the surface of the air core as a free-boundary which has to satisfy a jump condition, the Young-Laplace equation, relating the physics to the geometry. Based on this model, we are able to explain, qualitatively, some phenomena that have puzzled research workers in the field for many years, and can show, through the air core behaviour, the influence of material parameters on the performance of the hydrocyclone.

Jan 1, 1993

By Martin J. Hughes

The Eagle Mountain Mine of the Kaiser Steel Corporation is located in the California portion of the Colorado Desert at a distance of about 60 miles east of Indio, California. At the present time, this mine is producing at the rate of 5,000,000 tons of concentrate per year. A total of 1,000,000 tons of ore per year is presently being sold on the Japanese market while the remainder is consumed by the Kaiser Steel Company blast furnaces at Fontana, California. A new Pellet Plant and Concentrator is presently under, construction with completion scheduled for May or June 1965. This plant will have a rated capacity of 2,200,000 tons of pellets per year and essentially all of this production will be sold to Japanese steel companies.

Jan 1, 1965