Search Documents

By Christopher M. Moore

DK Recycling und Rohelsen GmbH converts 380 000 annual tonnes of iron containing waste materials Into pig Iron. Zinc Is the main reason that these materials are classified as waste. The materials are processed In the conventional way by making sinter which is then smelted in a blast furnace to foundry grade pig iron. The trick lies not in the unit operations which are quite standard but rather In the modifications made to the plant and operating procedures to cope with the much higher levels of tramp elements.

Jan 1, 1995

By V. Ferrari

This report documents the three-phase program to design, fabricate, test, and demonstrate economical and practical methods of reducing noise levels on underground coal mining portal buses (mantrip vehicles). The noise-control treatments applied to a production-model portal bus were as follows: ? Wheel/rail vibrations were isolated from the vehicle frame by inserting elastomeric materials between suspension components. ? Vibration-induced noise was reduced by replacing all large sheet metal panels (except floor plates) with damped steel panels. ? Motor noise was reduced by tight-fitting covers made from damped steel and lined with sound-absorbing material, and by elastomeric motor mounts. ? The standard spur gears used in the traction drive system were replaced with helical gearsets. The program achieved the goal of reducing the average sound-level to below 85 dBA for typical operating conditions.

Jan 1, 1981

By H. Walqui

This paper describes operating gains resulting from standardizing operating and maintenance practices to improve the performance of the pebble crushing circuit at he Empire Concentrator. Past efforts have led to improved operating time but no additional throughput gains. New Operating standards and checklists were developed and introduced. The content and frequency of the review process indicators was then changed to take advantage of the new practices resulting in an increased feed rate and availability through the pebble crushing circuit.

Feb 27, 2013

By Felix duBreuil

The present sampling procedure for evaluating the rock dusting conditions in a coal mine is time consuming. This study considers means by which this procedure could be simplified. Surveys were conducted in six coal mines in Pennsylvania to determine the in¬combustible content of the deposited dust. Some 2,000 samples were analyzed and statistically evaluated. It is suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error.

Jan 1, 1972

By H. Leitch

In laboratory experiments, the Bureau of Mines investigated melting, quenching, and sulfuric acid leaching of alumina from mixtures of albite and anorthite, and from anorthosites containing 26 to 32 percent alumina. Variations in pouring temperature, quenching and leaching conditions, were studied with respect to the extraction of alumina and impurities. Virtually all of the alumina was dissolved by leaching melted and quenched California anorthosite in boiling 16-percent sulfuric acid solutions for 15 to 30 minutes. The leach solutions were readily separable from the solid residue by conventional thickening and filtration techniques. Only 2 to 5 grams of SiO2, Fe2O3, or CaO dissolved per 100 grams of alumina. The quantity of SiOz in solution varied inversely with the duration of the leach and with the concentration of the H2SO4 solution used. Melted and quenched Wyoming and Minnesota anorthosites with SiO2:CaO weight ratios of 4.3 and 3.2, respectively, were less amenable to sulfuric acid leaching than California anorthosite with an SiO2:CaO weight ratio of 5.3. However, excellent results were obtained on the Wyoming and Minnesota anorthosites by the addition of SiO2 to these materials before melting, in quantities sufficient to adjust the SiO2:CaO weight ratios of the furnace charges to between 4 and 6.

Jan 1, 1966

By W. G. Davenport

Changes in copper extraction from 1960 till today are documented. The top ten changes have been: (a) replacement of reverberatory smelting by high intensity oxygen rich smelting (b) growth of the Outokumpu flash smelting to over 50% of the world's smelting capacity (c) successful development of single furnace coppermaking but only for low slag fall concentrates (d) replacement of the batch Peirce-Smith converter by continuous converting, but only in a few cases (e) increased SO2 capture throughout the industry, mainly-as sulfuric acid (f) development of low initiation temperature `big bight' Cs catalysts for treating the continuous high-SO2 strength gases from continuous smelting/converting (g) complete replacement of reverberatory anode scrap and cathode melting furnaces by the Asarco shaft furnace (h) adoption of stainless steel permanent cathodes and automated stripping technology for electrorefining and electrowinning (i) complete elimination of wire bar casting by continuous bar casting/rod rolling (j) development and adoption of extractants for turning weak impure leach solutions into strong pure electrolytes. It is postulated that the biggest possible change over the next 20 years would be complete replacement of smelting/converting by hydrometallurgical processing. However, this seems unlikely due to copper purity, precious metal recovery, and economic concerns. The increasing value of sulfuric acid to many copper companies gives chalcopyrite smelting/oxide-supergene leaching a nice synergy especially with the energy credits now coming from continuous smelters, and their acid plants.

Jan 1, 1999

By S. H. Ash

No single factor in modern civilization has played a more important part in the lives of our people than mechanization in industry and to it civilization owes much of its progress. In no industry has mechanization met more opposition than in coal mining, where ?the introduction of mechanical equipment has been opposed on many fronts for economic and social reasons. The term 'mechanization? as used in this report refers to the application of machinery to cutting, loading, and transporting coal from the face to the mine cars. During 1933, 84.7 per cent of the underground production of the bitu-minous-coal mines of the United States (1) was cut by machines, while in Washington only 17.6 per cent was machine-cut. Information in this report has been obtained from personal observations and from operating officials in the Roslyn-Cle Elum coal fields, especially D. R. Swem, manager of coal operations, and Thomas Murphy, superintendent, of the Northwestern Improvement Company, to whom the author is indebted for assistance. INTRODUCTION Although Washington coal-mining problems relating co mining methods, ventilation, drainage, and preparation of coal have been discussed in many publications, little has been published on mechanization in this region, principally because it has not been accepted generally that mining machines, mechanical loaders, and conveyors are necessary or economically adaptable to the variable and steeply inclined coal beds of Washington. Production of coal in Washington reached its maximum in 1918, when 4,128,424 short tons were produced; from that year, the trend was downward until 1934, when production was 1,383,103 short tons, the lowest since 1898; for the past two years, production has risen steadily.

Jan 1, 1937

By R. Lestari

Newmont Batu Hijau operates with an accelerated mining rate to optimize life of mine (LOM) project economics. This results in a portion of ore mined being stockpiled for reclaim and processing throughout, and at the end of mine life. LOM economics can be further enhanced by preserving stockpiled ore value by mitigating oxidation effects. A detailed stockpile ore oxidation study was conducted to: ?? Develop a practical understanding of how oxidation affects ore value; ?? Determine how oxidation rate can be controlled, and; ?? Determine how oxidation effects can be mitigated to preserve ore value. The result of the study is a stockpile management strategy that significantly reduces oxidation related losses and, implementation of that strategy within practical constraints. Implementation includes installation of Controlled Potential Sulfidisation (CPS) flotation to facilitate oxidised sulfide copper recovery and, recovery of dissolved copper from stockpile drainage solution into saleable product. This paper describes the study results including managing and predicting stockpile oxidation with time, monitoring performance of implemented CPS flotation and recovery of dissolved copper from stockpile drainage. These are essential elements of successful long term mine operation in Batu Hijau.

Jan 1, 2014

By A. L. Service

In 1965 the Western phosphate industry ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock and phosphate rock products. It has become an important regional industry and, since the close of World War II, it has become important in the national phosphate economy. This report includes an evaluation of the trends and outlook for the Western phosphate industry through 1975 as part of the Bureau's program to determine the rate at which the Nation's mineral resources are being utilized. The first part of this report is concerned with the relationship between the Western phosphate industry and that of the United States and the world. It describes the principal phosphate deposits and discusses production, export, and import of phosphate rock and marketable products. The second part of the report is concerned with the Western phosphate industry and discusses trends and outlook through 1975. Projections for the utilization of phosphate rock, phosphate fertilizers, and elemental phosphorus have been developed and extended through 1975 in an effort to provide data and information pertaining to the rate of depletion of the Nation's phosphate resources.

Jan 1, 1967

By A. N. Baldwin

This report documents the work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plans developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

By J. A. Russell

MR. M. W. Boom: I would like to congratulate Mr. Russell on his fine paper. One very good point which has always appealed to me is the smooth working of a steam hoist as compared with electrical. He does not mention the steam hoist at Springhill which has been working there for a good many years. MR. S. R. NEWTON: I have read with a great deal of interest the paper presented by Mr. Russell on the development of haulage engines in the mines of the Dominion Steel & Coal Corporation. He is to be congratulated on having produced a comprehensive article showing, step by step, the various improvements that have been made over the years in the design of such engines. I am quite in accord with Mr. Russell's statement that the positive tooth clutch can have too many teeth, and also that the method of driving a sliding clutch hub of any design should be by means of a hexagon or octagon on the shaft. Where the clutch hub does not of necessity slide on the shaft it can be pressed on and keyed to the shaft in the normal manner. With regard to the 'Cramp' internal-expanding jaw-type clutch, while it is true there are more moving parts than with the clutch consisting of a ring with internal cut teeth and a driver having a fewer number of teeth as .described by Mr. Russell; there are compensating advantages to the internal expanding jaw-type of clutch. The V shaped profile of the teeth permits of engagement of the clutch with very much less 'jockeying' of the drum. This is particularly the case in vertical-lift mine hoists, where it may be necessary to engage and disengage the clutching mechanism at frequent intervals.

Jan 1, 1944

By Mark L. Chatman

The U.S. Bureau of Mines studied mineral resources of the Dragoon Mountains Unit, Coronado National Forest (54,264 ac), Cochise County, AZ. This study involves literature and field investigations with a focus on mine and prospect sites, which were inventoried and mapped; maps are contained in this report. Rock-chip samples were taken from mineralized zones and from some mine dumps; assays of the 477 samples are in appendixes. Mineral deposits are genetically and spatially related to Tertiary-age granitic intrusive activity. Most metallic mineral deposits are also strongly fault-controlled. Colored marble resources (270,000 st) are valued at approximately $6.5 million, if all were to be developed and sold as landscaping material in the form of-marble chips. However, with current demand, it is unlikely that regional markets could absorb all this material. Economic modeling of copper-zinc-silver skarns suggests none would be profitable to mine and capitalize at early 1993 commodity prices, mainly due to the small estimated size of the deposits (30,000 st to 40,000 st maximum). In the entire Unit, 140,000 st of inferred subeconomic skarn resources were estimated by USBM on five different skarn trends; measured subeconomic resources are negligible. Exploration by industry, 1992, was small-scale (on 2 skarn trends and 1 auriferous fault zone).

Jan 1, 1993

Conventional ferronickel smelting has five main steps: Drying, calcination, prereduction, smelting and refining. In the scope of the current work, smelting experiments were conducted using Sivrihisar laterite ores (1.26% Ni) of Turkey. The ore samples previously subjected to drying, calcination and prereduction stages were smelted in alumina crucibles in a laboratoryscale horizontal tube furnace under argon atmosphere. Smelting experiments were performed at 1500, 1550 and 1600 oC. The amount of excess coal used in prereduction step was another variable. Sivrihisar laterite ore is a limonitic one with low MgO composition. Therefore, MgO was added to the smelting charge as a flux. The effects of experimental variables on metal Ni content and slag composition were investigated.

Jan 1, 2012

By W. C. Joughin

The science of soil mechanics is 100 years old, and rock mechanics is about 80 years old. While methods of analysis and design have been developed and have evolved over time, these are relatively young sciences. The rapid increases in computing power and new technologies have enabled more sophisticated modelling and monitoring. However, there are still many aspects of soil and rock mechanics that are not well understood. Geotechnical failures, which have major consequences, still occur. These consequences may include environmental damage, major production holdups and associated loss of revenue, damage to infrastructure, and loss of life. High-consequence events, which are rare, are more difficult to anticipate and to design for, because by their nature they involve extraordinary circumstances or conditions, often geological in nature. The risks are usually mitigated by conservative designs and monitoring. Detailed geotechnical investigations help us to understand the natural variability of soil and rock masses and identify unusual or unexpected conditions. Investigating and researching major geotechnical failures is essential to enable these unusual circumstances to be anticipated. In the past, severe unanticipated events may have been treated as natural events or ‘acts of God’. However, society now has much greater expectations and it is essential to have policies and procedures in place that enable appropriate management of these rare, high-consequence risks. A good example is the Global Industry Standard on Tailings Management (GISTM), which was introduced after the catastrophic dam collapse at Vale’s Corrego de Feijao mine in Brumadinho, Brazil. The address will explain the concepts of uncertainty and variability, and how they should be taken into account in geotechnical design. The challenges facing geotechnical engineers, mine owners, and managers will be discussed. referencing a number of real case studies.

Sep 6, 2023

By Thomas Novak, Sampurna Arya, Joseph Sottile

Dust generation and its dispersion in a longwall mine pose significant health and safety issues. The concern is prominent at both the working face, where coal excavation exposes workers to high dust concentrations, and also in the return, where float dust accumulates. To address this issue, researchers at theUniversity of Kentucky designed and fabricated a flooded-bed dust scrubber integrated into a full-scale physical model of a longwall shearer. This mock-up was installed in the longwall test gallery at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). A full-factorial experiment was designed to measure the effectiveness of the scrubber on dust capture. Test results indicated dust reduction of up to 57% in the return airways. This paper presents the development of a computational fluid dynamics (CFD) model and its validation by comparing the simulation results against the experimental results. The CFD simulations show good agreement with experimental results with differences between + 6.9 and − 9.7%. The validated CFD model was used further to predict the scrubber performance under additional operating conditions, resulting in a dust reduction of up to 66.5%. With this level of success, the scrubber concept can be a game changer for the mining industry, and it can be utilized to improve health and safety in longwall mines.

May 26, 2020

By M. A. Evanto

Since the late 1970's, the Roof Control Division (RCD) of MSHA's Technical Support has been performing linear analyses for the enhancement of miners' safety. This remote sensing process uses Landsat data to predict areas of potentially hazardous ground conditions in underground mines. To date approximately 700 analyses have been completed by the RCD, with nearly 75 being performed with the current equipment, software and methodology which was updated in early 1995. While success is difficult to measure, requests for linear analyses continue to come from large and small mining companies which suggests the industry's acceptance of the process.

Jan 1, 1998

"INTRODUCTION These inspection standards have been prepared for use as a guide for the Federal inspection of anthracite mines. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7231 in January 1943 and used as a guide for Federal inspections. Numerous changes in the original standards have been made, due in part to recognition of shortages of some types of safety equipment due to the war, in part to need of additional standards to cover certain mine conditions and practices, and in part to conditions not foreseen when the original standards were prepared.Throughout these standards reference is made to determining the methane content of the mine air by using a permissible flame safety lamp. The Bureau has approved various electrical devices for the detection of methane, but it is recognized that new devices for determining the percentage of combustible gases as well as the percentage of oxygen, might be perfected for general use in mines, and therefore it may be necessary to revise certain standards to include the use of such equipment if and when the device is accepted as being permissible.About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however, failure to carry out the suggestions made in such of the other standards as are applicable may also lead to loss of life.With continuing change in mining methods, some of these standards may become inapplicable, and further revision will be advisable. Therefore, question regarding these standards and suggestions regarding new standards should be brought to the attention of the Bureau, so that changes may be made from time to time. Numerous changes proposed by mine operators and by State mining departments have been incorporated in these standards."

May 1, 1944

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By Thomas A. Milne

As part of the broad program to improve the safety of underground coal mines, the Pittsburgh Mining and Safety Research Center sponsored several detailed studies on the inhibition of coal dust-air explosions. The present study was one of these. The goal of the research was to advance the development of improved coal-dust explosion inhibiting agents by determining, on a laboratory scale, the basic chemical processes involved in the inhibition of coal-dust flames by dry-powder agents. B. Our Approach Neither the basic molecular processes involved in coal combustion, nor the molecular mode of action of dry-powder agents, are known with certainty. Our approach, therefore, involved the direct determination, by sampling techniques, of species behavior in small, aerodynamically simple flames. To further aid in separating behavior of coal and dry-powder inhibitors, the latter were studied in CH4-air flames.

Jan 1, 1976

By John E. Conley

The great demand for metallic aluminum for the prosecution of World War II caused the consumption of bauxite, the common ore of aluminum, to increase greatly. Prior to the war, the domestic deposits 'of bauxite, which occur chiefly in Arkansas and less extensively in Georgia, Alabama, and Mississippi, supplied only: about 30 ,percent of the ore required for aluminum-metal production and approximately 40 percent of alumina for all purposes. Enemy activities during the war seriously interfered with shipment of bauxite from the normal peacetime source in Surinam, Netherlands Guiana, South America, and focused attention on the necessity for increasing production from known domestic deposits. Even in peacetime, the production of aluminum ore in the United States could not satisfy requirements. Field drilling and exploration by Bureau of Mines engineers resulted in the discovery of important tonnages of high-grade bauxite suitable for treatment by the conventional Bayer process, Although an ore containing approximately 55 percent Al2O3 and only 2 to 4 percent SiO2 is preferable, it was necessary to use ores containing up to 8 or 10 percent SiO2. Because of the lower recoveries of aluminum with increased silica content, the Reconstruction Finance Corporation, through the Metals Reserve Company, established a base price of $4 for a 50-percent Al2O3 ore, containing 13-percent silica, with a premium or penalty of 14 cents for each percent of Al2O3 over or under 50; each percent of SiO2 under 13 was awarded a 20-cent premium, and each percent over 13 suffered a penalty of 43 cents; all prices were on the basis of 1 long ton of ore, dry basis.

Jan 1, 1949