Search Documents

By P. Barnes

(Resident Engineer, 1873-75.) SEVERAL statements have been made to the Institute, somewhat detached from each other, as to the cost of some parts of these works, but they have not included any extended description of the. buildings or machinery. The general plan of the work connected with the water supply differs, in some important details, from that which has been common either in the Pittsburgh district or elsewhere, and a somewhat extended description may be of interest to the Institute, in connection with a note of the cost of the work. The plan as a whole, and nearly all the important details, were developed by Mr. William P. Shinn, C.E., the general manager of the Company. The immediate and responsible charge of the work was in the hands of Mr. John C. Lewis, C.E., to whom had been committed all the work of this general description, including the laying-out of the whole of the foundations, the erection of the buildings, and the grading and laying down of the entire railroad system. The continuous operation of the machinery and other fixtures of these waterworks, for more than three years, has fully demonstrated the correctness and economy of the plan adopted. No casualties of any moment have befallen the apparatus, and no improvements have been suggested as important except that the gate at the river end of the conduit should have been made more completely water-tight, so that the whole length of the conduit could be pumped out dry without resort to any temporary dam in the conduit itself. In general terms the works of the Edgar Thomson Company are situated on a plateau, about 52 feet above the low-water level of the Monongahela River, and about 2000 feet from its bank. The site of the works is bordered on one side by Turtle Creek, a small stream which drains a considerable area of coal mining territory. This creek is about 100 feet from the group of buildings which have been erected, but it flows into the Monongahela River at a point, about 1200 feet further up than that selected for the entrance to the water-works conduit. It was ascertained by analysis that the water in the creek contains an important percentage of sulphate of lime, while the water of the river is of unusual purity, in respect of any salts

Jan 1, 1879

By Zhou Jun

Water-quenched samples were taken from a commercial flash furnace at three levels along its reaction shaft during operation at high feed rate. The samples were subjected to a series of analysis and observation. Such processes of the feed in reaction shaft as oxidation, desulfurization, melting, slag and matte formation and etc., variations of particle size along axial and radical direction of the shaft are investigated. The following smelting mechanism in reaction shaft named as “Multi-particle and multi-phase fusion model” is proposed: (1) Fragmentation and collision of concentrate particles take place simultaneously in reaction shaft with particle size growing up. Collision produces large-size “unit melt” which falls into the reaction layer in the settler bath. (2) In the settler reaction layer below the shaft, weak bath smelting reactions take place among the shaft products, producing final matte and slag which separate into two layers. (3) The processes in the shaft are all progressive along the whole height of the shaft. The predominant reaction in the shaft is oxidation, not reduction.

By R. G. Knickerbocker, T. E. Evans, D. R. Torgeson

"INTRODUCTION Sponge iron is a product resulting from the reduction of an iron oxide at such a low temperature that fusion does not occur, and the reduced particles retain substantially the same shape as the original ore. The removal of oxygen in the reduction process leaves the metal porous and reactive. Sponge iron may be compared in general to a chemically precipitated substance insofar as reactive properties are concerned. The high specific surface and the orientation of metallic structure are factors which probably contribute to the reactive properties of sponge iron.The term ""gaseous reduction,"" as applied to iron ores, required clarification. Strong evidence exists, for example, that ore is partly reduced to sponge iron by carbon monoxide in the blast furnace at temperatures around 800° C. at a point that may be as high as 30 feet above the tuyores. In 1923 and 1924, Sims and Wood attempted to reduce iron oxide with carbon in an Arsem vacuum furnace at 980° C. These investigators found that only 6 percent of the iron was reduced to metal when the iron oxide-carbon mixture was heated for 1 hour under evacuated conditions, whereas at atmospheric pressure 70 percent of the iron was metallized. Their results indicate that the process of iron-ore reduction at temperatures below the melting point of the ore may proceed largely, if not entirely, by the action of reducing gases even when the reducing agent is solid carbon. Therefore, the term ""gaseous reduction,"" as used heroin, is defined as a process in which iron ore is brought into intimate contact with a reducing gas produced in separate-equipment from the reduction chamber itself.A large amount of pilot-plant development on gaseous reduction of iron ores has been carried out by the Bureau of Mines at the Boulder Experiment Station and had as its objective the reduction of fine iron ore by means of producer gas. The use of use gas was prompted by two considerations: First, the possible utilization of large reserves of Western noncoking bituminous coals and lignites contiguous to iron-ore drewwing; and second, an investigation of the results that might be achieved in the pilot-plant gaseous reduction of fine iron ores by means of a relatively reducing gas. The results obtained, it was felt, would be of considerable value in indicating the direction which gaseous reduction experimentation must take for the development of a commercially practicable and economic process for the production of sponge iron."

Dec 1, 1946

By Max Mason

In 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which automatically and continually conveys messages from underneath. We also have available the earth's gravitational field which furnishes us

Jan 1, 1929

By Jon I. Voltz

The U.S. Bureau of Mines has conducted fundamental coal fragmentation studies to evaluate the effects of impact energy and direction of bedding planes on dust generation, size distribution, and impact-output energy relationships. Product size distributions were obtained for the fragmented samples by screening to minus 150 mesh. The minus lS0-mesh fines were analyzed with a light scattering photometer with a measurement range of 176 to 1.9 /.tm. Increased input energy produced a significant increase in the weight of plus 3/8-in material for impact perpendicular to the bedding planes. No significant trend was observed for parallel impact. Impact direction had little influence on dust size distribution, and input versus output energy relationships. As expected, total airborne dust measured at time of impact and percent particulates below 11 /.tm in size generally increased with increased input energy for both directions of impact. Energy used for sample fragmentation increased with increased energy input.

Jan 1, 1989

By A. C. Barlow

The use of deep wells for waste disposal is not a new technique. The production phase of the oil industry has been using this method to dispose of unwanted oil field brine since the 1930's The adoption of this method by other branches of industry, however, to dispose of manufactured wastes is a relatively new development, but one which is finding increased use (2). Deep well waste disposal is not an ordinary technique even though it is finding relatively wide application. In fact, just the opposite is true; it is still a rather extraordinary measure. It is not now, nor is it ever likely to be a disposal method which can be assured of success before it is tried.

Jan 1, 1964

By Marius Jacobs

"Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a "plateau" and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have "exemplary" safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA’s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization’s mindset? What characterizes these organizations’ decision-making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensiveresearch since 1997 of organizations that suffered unexpected disasters.The Piper Alpha Oil Rig disaster in the North Sea, on the 6 July 1988, was one of the most pivotal events in safety around the world. It changed the thinking and focus of governments, whole industries and led to numerous books and papers. It resulted in new legislation, textbooks and a critical self-examination by the oil and gas industry.In short, an explosion and fire occurred when a pipe started leaking gas and ignited. A temporary flange, with no safety valve, was used to block off this pipe during a maintenance operation the previous shift. The permit to advise operators not to start the pumps on this line was misplaced and lost. Several deficiencies, problems and system failures coincided. A key factor was that the water deluge system was inoperable at the time and failed to extinguish the large fire that erupted, followed by an even larger gas explosion. The accommodation unit, situated on top of the oil rig, was the main "killing field" - most men gathered here to await instructions (which never came) and where they died from smoke inhalation. Later, a large explosion of the gas pipeline from an adjoined rig exploded and killed more people.The line of events and the associated system failures are all very relevant in the analysis of the accident, and provide the only insight into what caused the accident. But much "further back", inside the organization’s culture, lurks more dark matter. The first inclination is to ask what was "deficient" in the culture. Did they not care enough about safety, or about their people? Did they have a culture where production decisions were more important than safety considerations? Did they ‘coerce’ supervisors and employees to ignore safety precautions or did they just "fly by the seat of their pants"?Not surprisingly, it is very difficult to identify the true nature of the culture in that business because in such an aftermath of death and destruction, no one dare say that the safety culture was a ‘positive one, focused and caring’ or that the company was doing well in safety and that this is only a freak accident. Indeed, there were many deficiencies in the organization’s systems and procedures, such as the permit to work system.But there are some niggling questions: How is then that the Piper Alpha Oil Rig was actually considered the company’s most productive and safest oil rig in the North Sea? Why would this rig win a safety competition, 6 months before the disaster, with the deficient permit as its most outstanding successful system?"

Jan 1, 2014

By Stephen D. Cramer

The objective of the present studies was to develop thick adherent and coherent coatings of platinum and palladium on refractory metals and other substrates of industrial and engineering importance. Existing platinum and palladium electrolytes were modified to make them suitable for the electrodeposition of thick deposits. The optimum operating conditions for these electrolytes were established. Pretreatment procedures for columbium, copper, graphite, molybdenum, nickel, stainless steel, tantalum, titanium, tungsten, vanadium, and zirconium substrates were studied. New pretreatment procedures for columbium, molybdenum, stainless steel, tantalum, tungsten, and nickel were developed. The internal stress and hardness of selected electrodeposits were measured. The effects of heat treatment upon the properties of electrodeposits were studied.

Jan 1, 1967

By M. M. C Jiménez, D. C. Buzzi, D. C. R. Espinosa, J. A. S Ténorio, G. F. R Oliveira

In this work the extractive and selective capacities of solvent extraction synergistic systems to recover nickel and cobalt were evaluated. The liquor used was from the high pressure acid leaching process (HPAL). Initially the industrial liquor, processed from lateritic ores, was analyzed to identify the concentrations of the metals. Experiments of synergistic solvent extraction were performed later. The extraction liquid-liquid was carried out with a mixture of Cyanex 272 (CY) and Ionquest 290 (IQ) extractants. The process was executed with the temperature of 65 ºC, pH of 5.2 and the ratio aqueousorganic 2:1. Systems of 80% kerosene and CY 20%, CY 16% - IQ 4%, CY 12% - IQ 8%, CY 8% - IQ 16%, CY 4% - IQ 16%, IQ 20% were studied during 20 minutes. The results of this paper showed that the mixture of these two extractants doesn’t improve significantly the recovery of nickel and cobalt from liquor.

Jan 1, 2014

By Qing Wang

A longterm overburden removal plan can be realistic and optimum only when the cost and capacity profiles off the equipment assigned to the operation are taken into consideration. Therefore, the planning should involve the proper assignment of equipment capacity by insuring a timely investment and a timely replacement policy throughout the mine life. A dynamic solution algorithm has been developed, by which all possible truck fleet alternatives are evaluated for each year off the operation. Cumulative cost off the operation is carried throughout the analysis. The optimum solution is obtained by selecting the minimum cumulative cost at the last year and tracing backward the best fleet alternative for each year. The solution provides: 1. the optimum amount of overburden to be removed each year; 2. the best fleet to be assigned to the job; and 3. the best equipment replacement policy.

Jan 1, 1989

By R. S. Moehlman

IN recent years, exploration and development by diamond drilling has become a popular attack on the problem of finding new ore shoots and developing extensions of known shoots. Diamond drilling has been used in recent years in extensive sampling of disseminated copper deposits, in preference to churn drilling. At the Harvard gold mine, near Jamestown, California, Philip R. Bradley, Jr., general superintendent, reports that: "The Harvard work was a singular example of the reliance that can be placed on diamond drilling in evaluating an ore body." Drilling at the Harvard mine will be discussed in a subsequent section of the paper. So popular has diamond drilling become, indeed, that many who have had slight experience with drilling are inclined to regard it as a cheap cure-all. This paper proposes to show some of the limitations on the application of drilling and some of the steps that should be followed in drilling programs to obtain reliable results. COST OF DRILLING Drilling has the advantage, over shaft sinking and drifting, of lower cost and greater speed. As compared with churn drilling, the advantage of bringing up a coherent sample instead of fine cuttings for a sample is obvious. Diamond drilling is generally more expensive, however, and more engineering effort is required in combining the average of core and sludge samples. Exploration of drift walls by hammer drills to a depth of less than 50 ft. is generally cheaper than diamond drilling, but beyond this depth the diamond drill is cheaper and more efficient. The principal factor in determining cost of drilling is the character of the ground drilled. Broken ground with many fissures is most expensive to drill. Hard ground is less of a problem with diamond drills than with ordinary machine drills. Hardness or softness affects only the speed of drilling. Caving, easily washed, sandy or clayey ground requires continual cementing and casing, which is the greatest cost problem. Thus, soft, incompetent ground is more costly to drill than hard, massive ground. Cost of drilling per foot in good to fair ground varies from less than $1 per foot, achieved in some districts in Ontario, the Mother Lode, and Missouri, to $5 per foot in many western states. In bad drilling ground, costs may range from $5 to $15 or more per foot, thus approaching the cost of drifting. Other factors that increase the cost per foot are: I. Short total length of hole drilled, so that the cost of moving in crews and equipment must be spread over a relatively few feet. 2. Cost of drilling per foot increases with depth beyond about 500 ft., as more time is consumed in pulling rods. 3. Cost of preparing drilling stations, getting air underground to stations, etc. 4. Inaccessibility and lack of water on the job make for higher costs.

Jan 1, 1946

By Young-Sool Jin, Heung Nam Han, Hong Joon Kim, Jae Kon Lee

A mathematical model was developed considering non-symmetric cooling' and stress distribution in both thickness and width direction of strip on a run-out table of hot strip mill. In order to solve a transient heat transfer equation including the heat evolved from phase transformation, a finite element method coupled with thermodynamic and kinetic analyses was applied. The heat capacity of each phase and heat evolution due to phase transformation were obtained from the thermodynamic analysis of the Fe-C-Mn-Si system based on a sub lattice model. The phase transformation kinetics of the steels was derived by using an inverse additivity technique with continuous cooling experiments. Heat transfer coefficients of strips on the run-out table were, by applying an inverse method, determined from the actual mill data under various cooling conditions. As for the stress analysis, the density change of strip due to cooling and phase transformation, and the transformation superplasticity were considered. A 90nstitutive equation for the transformation superplasticity, which is related to the phase transformation kinetics and the internal stress due to the density change of strip, was applied. A finite element method was adopted to calculate the deformation behaviour of strip on a run-out table of hot strip mill. Using the models, the temperature-phase-deformation history and distribution of a strip on the run-outtable was calculated.

Jan 1, 2001

By Lucas Coelho da Silva

Este trabalho tem a pretensão de problematizar a influência da corrosão, sobretudo nos trocadores de calor, e trazer a importância de um estudo prévio detalhado, ressaltando como o desempenho deste equipamento está relacionado ao material utilizado e como esse estudo pode nos abster de grandes dispêndios. Através de ensaios eletroquímicos vamos estudar o comportamento do aço Super Duplex UNS S32750 em diferentes meios corrosivos, com o intuito de avaliar se o nível de corrosão do material é adequado para as condições severas de operação impostas a um permutador de calor.

Aug 16, 2017

By Roy P. Hudson

A micropyrometer known as the De Graaf apparatus has several advantages over the gas-furnace method for determining ash fusibility. When the De Graaf apparatus is operated by a modified method of procedure, the results closely check those of the gas-furnace method. This is indicated by tests on 27 samples of coal ash, with an extreme variation in fusibility values of 654" F. However, most of the ashes fused at temperatures between 2300º and 2500º. This, presumably, is the temperature interval within which the micropyrometer gives the best results. Additional comparisons are desirable. DISCUSSION (Thomas G. Fear presiding) A. C. FIELDNER,† Washington, D. C. (written discussion‡).-—The Pittsburgh Experiment Station of the Bureau of Mines has made two investigations1 of the micropyrometer for determining the fusibility of coal ash. These studies were undertaken with a view to adopting the micropyrometer method us a substitute or alternate to the present standard gas-furnace method, in view of the obvious advantages of greater speed, smaller ash sample, smaller laboratory space requirements, less equipment and greater comfort to the operator. However, the investigation showed that the micropyrometer type of furnace as then operated in five laboratories having this equipment could not be accepted as an alternate to the standard gas furnace, which is capable of close duplication in different laboratories, as shown in a recent colmparison between the Pittsburgh Experiment Station of the United States Bureau of Mines and the Fuel Research Station of Great Britain.2 The algebraic meau

Jan 1, 1934

By Xing Yang, Zhen Peng, Guangwen Zhang, Haifeng Wang, Yaqun He

"Triboelectric separation of ilmenite ore based on the tribocharge differences between ilmenite and gangue minerals was conducted in this study. Triboelectric characteristics of ilmenite and its associated minerals were studied using polyvinyl chloride (PVC), pentatricopeptide repeats (PPR), copper, polymethyl methacrylate (PMMA), stainless steel (SS), teflon and quartz glass (QG) tribochargers in lab triboelectric unit. Results demonstrated that the ilmenite particles tribocharged positively while gangue minerals tribocharged negatively using PVC as tribocharger. The particle size also has a significant effect on tribocharge, and the -0.125+0.074 mm is the optimal size fraction of triboelectric separation. Charge-mass ratios of minerals increase with the increases of tribocharging length, but the increasing rate gradually reduce. At 1.5 m tribocharging length, charge-mass ratios of ilmenite, quartz, feldspar and mica are up to 6.07 nC/g, -6.05 nC/g, -4.30 nC/g and -4.56 nC/g, respectively. Based on the triboelectric characteristics of each mineral, triboelectric separation of ilmenite was conducted, and the grade of ilmenite ore increased from 15.47% to 28.40%. INTRODUCTION As a transition metal titanium plays an irreplaceable role in medical, aerospace and materials due to its light weight, high strength and corrosion resistance. Pure titanium dioxide is an excellent white pigment and is widely applied in industries of paint and textile. Ilmenite is the main raw material for titanium industry. For the beneficiation of ilmenite, series methods have been proposed, such as the application of dry magnetic and wet gravity separations to separate the ilmenite from the zircon and rutile. Electrostatic separation is extensively used in the beneficiation of heavy mineral sands for the recovery of rutile, zircon and ilmenite while flotation is used to separate fine ilmenite (Mehdilo et al., 2014; Fan et al., 2014). Compared with flotation and gravity separation, electrostatic separation does not consume water, and native properties of materials will not be changed and energy consumption will be reduced (Wang et al., 2014). Thus, the wide application of electrostatic separation and other dry separation methods is a trend in separation and purification industry, especially in water-scarce areas."

Jan 1, 2018

By R. E. H. Pomeroy

THE statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Me Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. ½ in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5° B., flashing in open test at 199° F. The oil is heated to about 200° F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 lb. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-oz. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and "dog houses? to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent.

Jan 2, 1915

The objective of a mine planning exercise is to plan a safe mine that maximises net present value (NPV) for the project. Two primary elements are key to design of a mine plan optimised to maximise profit: selection of an optimised production rate and selection of an optimised equipment fleet. Both depend upon accurate estimations of capital and operating costs for the equipment and for the life cycle of the mining operation. Once a trial production rate is determined, a primary equipment fleet, ie excavators, haulers, and blasthole drills, can be determined based on material characteristics and haulage distances and gradients. An auxiliary fleet, dozers, road maintainers, service trucks, etc can be determined using less rigid productivity criteria. With an equipment fleet determined, operating and support personnel can be assigned based on shift requirements and equipment operating needs; and material and supply requirements can be estimated. Knowing the areal dimensions of the major equipment items, road widths and repair shop dimensions can be determined. Personnel numbers and supply requirements determine the square metre sizes of offices, change rooms, and storage facilities. Reliable sources of capital and operating unit prices and costs for all these items are referenced in the paper. Once preliminary capital and operating cost estimates are calculated by applying unit costs to equipment, personnel, material and supply needs, potential profit can be tested using DCF techniques. An optimised mine plan can then be determined by testing the potential profitability of multiple mine production rates. Because of the economies of scale, full capital and operating cost estimates must be completed for each production rate in order to produce meaningful comparisons.

Dec 6, 2010

By Ravi S. Bellur-Ramaswamy, Daniel A. Tortorelli, Robert Haber, Nahil A. Sobh

We optimize continuous quench process parameters to produce functionally graded aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include 1) the process parameters to be optimized, 2) a cost function: the weighted average of the precipitate number density distribution, 3) constraint functions to limit the temperature gradient (and hence distortion and residual stress) and exit temperature, and 4) their sensitivities with respect to the process parameters. The cost and constraint functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine the precipitate particle sizes and their distributions. Both the temperature and the precipitate models are solved via the discontinuous Galerkin finite element method. The energy balance incorporates nonlinear boundary conditions and material properties. The temperature field is then used in the reaction rate model which has as many as 105 degrees of- freedom per finite element node. After computing the temperature and precipitate size distributions we must compute their sensitivities. This seemingly intractable computational task is resolved thanks to the discontinuous Galerkin finite element formulation and the direct differentiation sensitivity method. A three-dimension example is provided to demonstrate the algorithm.

Jan 1, 2001

By W. W. Culter

"This paper is the outcome of thorough investigation into the value of the previous methods used for deriving production decline curves. It is highly important that methods be employed that are fundamentally sound and also practicably applicable. Six methods commonly used were studied. Some of these were found to be fundamentally in error; some save reliable curves but involved much work and time in the preparation; others gave reliable curves with less time and effort.It was found that of the methods previously employed the ""family curve"" method described in Bull. 134 Amer. Inst. Feb. 1918, pp. 499-500 by Lewis and Beal, was probably the most satisfactory. The now method given in this paper ploys the same principles as the ""family curve"" method, but is mathematical instead of graphical,The engineer and the oil man should carefully boar in mind both the use and the limitations of the average production curve such as is derived by the ""family curve"" method or other methods mentioned. Estimations of future productions or of underground oil reserves of a particular tract or well should be made from the production records of the tract or the well itself wherever such records are satisfactory. The use of the average curve of a district or field should be applied only to those properties or wells where there are not sufficient data to construct individual or tract production records, or where the productive life so short that a satisfactory individual record can not be obtained."

Jul 1, 1920

By D. M. May

"Cut-and-fill mining is a stoping method that has been widely utilized in the mining industry over the past forty years. It took preference over shrinkage methods at Levack in the early 1930sbecause of its safety aspects; i.e., prompt support of the stope sidewalls, good working floors and better accessibility to support poor back areas. In addition, higher recoveries of ore were possible because of the flexibility of the method in that silling could take place easily at any horizon; low-grade ore could be sorted and left in the stope as fill and certain zones of rock could be left unmined. With modern techniques, a steady production rate can be established, as filling and mining can be carried out stimultaneously.AIthough there are numerous variations of cut-and-fill mining throughout the world, this paper reviews the original type of mining, with modifications and improvements through the years to present modern practices, with the Levack West operation appearing to be the most productive at this time. Stoping efficiencies have also increased substantially from the original 10 tons per manshift to the present 55 tons per manshift.The paper also outlines the many improvements that have been made with respect to mucking and ground support operations; from hand mucking in a single stope to the use of frontend loaders and haulage trucks in fully accessible stope complexes; and from timber props to roof bolts of various types. Although present methods are extremely satisfactory, experimentation is continually being conducted to improve safety and productivity for future mining.IntroductionThe major mining operations of the Ontario Division of Inco Limited are located in the Sudbury Basin (Fig. 1). Around the rim of this geological formation and within 30 miles of the City of Sudbury are nine producing mines and one ' open pit operated by the company .Ore production currently approximates 11.5 million tons per annum from underground and open-pit operations. Underground mining methods include sub-level caving, shrinkage, cut and fill, undercut and fill, blasthole and vertical retreat. The Levack Complex, the main plant of which is the central Levack Mine, produces 11,000 tons per day.The first prospecting in the Levack area, in 1887, was conducted by James Stobie, who examined rock cuts along the route of the Canadian Pacific Railway to the northwest of Sudbury. However, it wasn't until 1913 that operations commenced at Levack under the Mond Nickel Company."

Jan 1, 1981