Search Documents

By J. F. Childs

"INTRODUCTION Comprehensive overviews of the world-class talc deposits and related prospects in Montana were published by Olson (1976) and by Berg (1979). Both of these compilations include detailed descriptions and maps of the talc deposits and occurrences and were followed by a regional map and summary descriptions of the talc deposits published by Van Gosen et al. (1998). More recent publications, descriptions and field guides for some of the deposits include Underwood et al. (2014), Cerino et al. (2007), and Cerino (2002). The present paper focuses on some of the more recent ideas regarding talc formation that have developed since the publication of the earlier overviews. Olson (1976) reported that talc production from the deposits in southwestern Montana was over 200,000 tons in 1974 and that talc production had doubled between 1969 and 1974. The last year for which the U.S. Geological Survey published production records for talc by state was 1993. Production in Montana in 1993 was 350,000 tonnes (Virta, 1994). Remaining reserves are substantial at all three of the producing mines in the district. Minerals Technologies Inc., the parent company of Barretts Minerals Inc., stated in its 2014 annual report that it has reserves of 2,791,000 tons of talc. Imerys stated in its financial report for 2014 that it had 19,638,000 tons of proven and probable talc reserves at its North American mines. Although the Imerys reserves were not reported by individual mines or states, a large proportion of the total reserves would likely consist of the reserves at the Yellowstone mine, located south of Ennis, Montana. Talc mined in southwestern Montana is of high purity and is the quality used in a wide variety of applications including paints, ceramics, plastics, rubber, coatings, agriculture, cosmetics, and pharmaceuticals. GEOLOGIC SYNOPSES FOR MAJOR MINES AND COMMENTS ON REGIONAL DISTRIBUTION OF TALC OCCURRENCES The general geology of southwestern Montana is shown in Figure 1along with the locations of the three producing talc deposits in the area and the extent of pre-Belt marbles that host all of the talc mines and prospects. The term “pre-Belt” is used in the present paper because zircon and other radiometric data developed in recent years indicates that the metamorphic rocks that form the crystalline basement for the middle Proterozoic Belt basin in the Dillon Tectonic Block of southwestern Montana includes both Archean and Paleoproterozoic rocks (O’Neill et al., 1996; Foster et al., 2006; McDonald et al., 2012). An envelope or “corridor” has been superimposed on the geology in Figure 1 which encompasses all of the talc deposits that have a significant resource. This “talc corridor” will be discussed in later sections of this report. The more important talc deposits are discussed in this report section."

Jan 1, 2016

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By L B. Sukla, V N. Misra

Microbial desulfurisation of coal has significant advantages over physicochemical desulfurisation processes since the former process selectively removes the inorganic sulfur compounds and heavy metals without significant carbon loss. The purpose of this study was to improve the desulfurisation yield of a coal sample from northeastern coalfields, Assam, India using microbial technique. The coal sample contained 2.13 per cent of total sulfur and 2.59 per cent of ash. Stirred tank reactors of 40 L capacity were operated in batch mode. Initially, the reactor was fed with 40 L of slurry containing ten per cent (w/v) coal, ten per cent (v/v) inoculum of mixed culture of mesophilic acidophiles, native to coal itself and the requisite amounts of constituents for 9K medium without added ferrous sulfate. The percolate of the reactor was then used to seed the medium for the next experiment. The purpose was to obtain a better adapted and more active biomass which would give a better desulfurisation yield for coal. Further studies were conducted in the bioreactor, fed with 40 L of slurry containing ten per cent (w/v) pulp density of coal, ten per cent inoculum (derived from previous studies) and the medium, supplemented with ferrous sulfate. Results showed an increased total desulfurisation yield of 43 per cent in the latter treatment in comparison to the previous one, where the desulfurisation yield was only 23 per cent. The findings also demonstrated the convenience of using inocula derived from coal, where 50 - 60 per cent of pyritic sulfur was removed, while chemical desulfurisation is of little significance with the majority of coal types. The ash content was also reduced to 1.74 per cent as the low pH of the process caused dissolution of a number of common minerals present in the coal.

Jan 1, 2004

By D. K. Panda

The behavior of single drops with gas evolution at the interface is of interest because this is one of the important reactions that occur in oxygen steelmaking vessels, where a large amount of iron-carbon drops are dispersed in an oxidizing slag. The carbon dissolved in these drops, reacts with the slag to form CO, which is evolved as a gaseous phase. A room- temperature model was used to study the nature of this type of reaction including the effect of various factors such as viscosity and the presence of surface active impurities. Experiments were done for reacting drops over a wide size range to observe various regimes of behavior. Large single drops were levitated in a counter current flow to produce a sufficiently long residence time to allow the study of the various stages in the reaction. The emphasis of this work was to obtain photographic evidence of a high quality to describe all possible modes of behavior, and so a lot of effort was given to developing and perfecting experimental techniques.

Jan 1, 1994

By R. Grau

"After commissioning and start-up of the first 500m3 TankCell® flotation cell in 2014, the over 300m3 mechanical flotation cells have earned their place in large-scale flotation operations. These 500 to 630m3 cells, designed for projects with large throughputs, are proven to provide savings in project capital and operational expenditure through savings in foot print, energy consumption, and less equipment to install and maintain. Addition to savings in different phases of a project, these cells provides operational flexibility and has shown improvements in metallurgical performance. In this paper a case study from Kevitsa TankCell® e500 installation and Buenavista del Cobre TankCell® e630 installations will be given.INTRODUCTION After development (Grönstrand and Bourke, 2008), characterization (Morales et al. 2009; Yanez et al. 2009; Grönstrand at al. 2009), validation (Elgueta et al. 2009; Coleman and Dixon, 2010), and more than 350 industrial installations of the Outotec TankCell® e300 flotation cell, the well proven energy efficient TankCell® product family introduced the TankCell® e500 forced-air flotation cell late June 2012 (Outotec.com, 2012). The introduction of the 500 m3 flotation cell followed by introduction of a 630 m3 flotation cell, TankCell® e630, in October 2014 (Outotec.com, 2014). These large flotation cells are designed for projects with high throughputs where the number of cells needed for operation with smaller equipment would become large. The benefits of this size of flotation cells comes from the lower capital expenditures due to lower equipment costs, savings in plant footprint, less installation work with less auxiliary equipment, lower energy consumption, and less units per installation resulting in less components, spare parts and maintenance.The first TankCell® e500 was commissioned and taken into operation in October 2014 at FQML Kevitsa Cu-Ni-PGE concentrator, nowadays owned by New Boliden. The first TankCell e630 was taken into operation in January 2018 at GrupoMexico’s Buenavista del Cobre Cu-Mo concentrator. The start-ups of the first TankCell® e500 and TankCell® e630 followed with test work where the hydrodynamic performances of the cells were characterized and metallurgical performance studied. The results of the TankCell® e500 test work were presented in detail by Mattsson et al (2015a; 2015b) and TankCell® e630 by Grau et al. 2018. In this paper the metallurgical improvements achieved with the large cell installations will be presented."

Jan 1, 2019

By Redhead Robert J.

"In 1991, the Canadian Council of Ministers for the Environment (CCME) charged its Waste Management Task Group with developing a nationally coordinated strategy to measure, monitor, and achieve the objective of decreasing the generation of waste (solid and hazardous) by50% from 1988 levels by the year 2000.With the encouragement of the CCME, which viewed hazardous waste as largely an industry problem, a committee, the “Industry Action Group”, representing eleven industry trade associations with a strong interest and involvement in hazardous waste was recruited.The Municipality of Markham, Ontario was also recruited (Appendix 1)."

Jan 1, 1996

By K. P. V. Lei

The Bureau of Mines investigated molten salt electrorefining 'n helium atmosphere cells as a means for the production of ductile vanadium. 'Electrolytes composed of NaCl-VCl2, LiCl-NaCl-VCl2, BaCl2-KCl-NaCl-VCl2 KCl-LiCl-VCl2, and CaCl2-NaCl-VCl2 were tested. Two electrolytes, KCl-LiCl-VCl2 and CaCl2-NaCl-VC12, were selected for laboratory-scale production tests. A molten salt electrorefining process was developed for the production of ductile 99.6 percent vanadium from a commercial 90-percent grade. Using the CaCl2-NaCl-VC12 electrolyte, an 87-percent recovery of ductile vanadium was made; an 85-percent recovery was made with the KCl-LiCl-VCl2 electrolyte.

Jan 1, 1967

The Tuesday Morning session opened at 9:00 a.m. and was presided over by Mr. E. C. DeMoss, Vice President, Utah Construction & Mining Company, San Francisco, California. Mr. DeMoss introduced Mr. C. Howard Hardesty, Jr., Senior Vice President, Con¬tinental Oil Company, New York, N. Y. Mr. Hardesty spoke on the "Relationship of Coal to Progress in Oil Industry." Mr. Hardesty was born in Fairmont, West Virginia, 1922. He is an attorney by profession; he attended Mercerburg Academy in 1939 and received a Bachelor of Science degree from Duke University, 1943. He then served three years in the U. S. Navy and returned in 1946 to obtain his LL.B. from West Virginia University in 1949. Mr. Hardesty has had an outstanding professional career which started as a partner of the law firm of Furbee & Hardesty, Fairmont, West Virginia. He subsequently was West Virginia's State Tax Commissioner and President of the West Virginia Bar Association. In 1963 lie became General Counsel of Consolidation Coal Co., Pittsburgh, Pennsylvania; in 1964 he was made Vice President, Secretary and General Counsel, Consolidation Coal. In 1966 he was elected Executive Vice President of Consol, and, shortly after it was merged with Continental Oil Co., he was made Senior Vice President of Continental. He is married to the former Doris Wilson; they have two children and reside in Greenwich, Connecticut.

Jan 1, 1968

By S. Banisi, A. R. Hasankhoei, Gh. Parsapour, A. R. Ghasemi

At the Gol-E-Gohar mining and industrial Company, a pelletizing plant, which includes two parallel dry closed grinding circuits and a pellet production circuit, produces 600 t/h. Each grinding circuit consists of a burner, a dry ball mill (6 m×13 m) and an air separator. Each ball mill consists of a 2 m-long dryer chamber and an 11 m-long grinding chamber. Iron ore concentrate is fed to the drying chamber to decrease its moisture from 2.5% to below 0.2%. The drying chamber consists of 56 flights in two rows. It was found when the feed moisture content decreased from 1.3 to 3.5%, the throughput decreased by 14% (40 t/h) indicating a low performance of the dryer. In order to improve the efficiency of the drying section, a scale down version of the dryer was constructed in a 1m diameter mill with a transparent end to make image analysis possible. It was found that because of the inappropriate veiling profile in the drying section, most of materials are not subjected to the hot gas tunnel. To overcome this problem, various flights with different geometries were physically tested and also simulated by the KMPCDEM © software. With the aim of arriving at a proper veiling profile which maximizes the particles contact with hot air, a new flight design was obtained and tested. The installation of the rectangular tooth type flights in one of the mills in the plant made the comparison of the old and new designs possible. The evaluation of the designs in a period of three months indicated 15 t/h increase in the throughput in the case of the new flight design.

Jan 1, 2016

By Elson Renato Santos Souza, Ricardo Pondé Weber, João Carlos Miguez Suarez, Sergio Neves Monteiro, Suzane de Sant’ Ana Oliveira

Foi estudado a influência do aporte térmico, de soldagem, sobre a resistência balística de um aço de alta dureza (HHA) temperado e revenido (HHA), utilizando o processo de soldagem a arco. O aço HHA, temperado e revenido, foi caracterizado por análise metalográfica, ensaios mecânicos e ensaios balísticos. Os resultados mostram que o aporte térmico da soldagem teve influência significativa nas propriedades mecânicas da Zona de Fusão (ZF) e da Zona Termicamante Afetada (ZTA), ocasionando mudanças na resistência balística. O melhor desempenho balístico do material soldado foi obtido para a soldagem de baixo aporte térmico.

Oct 30, 2017

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling."

Jan 1, 2003

By Guy N. Bjorge, A. J. M. Ross, S. J. Staple, J. D. Johnson, J. F. Wiggert

In recent years the Homestake mine has been served by three shafts, the B. &. M., the B. & M. No. 2 and the Ellison, supplemented by an inside shaft, the Milliken, extending from the 2000-ft. level to the 3200-ft. level. In 1932, when a new operating shaft was under consideration, the bottom of the mine was at the 3200-ft. level. The B. & M. and the B. & M. No. 2 shafts were down to the 1550-ft. level and the Ellison was being deepened from the 2600 to the 3200-ft. level. All ore was hoisted at the B. & M. and Ellison shafts. Levels below the 2600 level, which were under development only, were served by the Milliken shaft. Below the 1550-ft. level, the mine was served only by the Ellison shaft from the surface. Within a few years, when ore reserves above the 1550-ft. level would be depleted, operation would be limited to the Ellison shaft and the auxiliary underground shaft. The Ellison shaft alone was not adequate for hoisting the entire output from the deeper levels and also handling all men and supplies. Furthermore, assurance of safety and uninterrupted operation required two fully equipped shafts to the deeper levels. Therefore a new operating shaft was authorized in November, 1932, and was named for A. J. M. Ross, the mine superintendent. Plans for New Shaft The B. & M. shaft, begun in 1878 before much was known of the form and extent of the orebodies, was too near the ore and was endangered by ground movement. In 1924 this shaft was seriously threatened and sinking of the B. & M. No. 2 shaft, to supplant it, was begun. The latter was completed to the 1550-ft. level in 1928. In the meantime ground movement at the B. & M. shaft had practically stopped and, though loss of the shaft constantly threatened, ore hoisting was con-

Jan 1, 1937

By B. Erik Ydstie, Tor Lindstad, Vianey Garcia-Osorio

"As a result of the high temperatures present in a Carbothermic Aluminum Process the content of aluminum and aluminum sub-oxide in the gases leaving this process is high. These gases as well as energy must be recovered. In a Vapor Recovery Unit were the aluminum compounds react in a series of Heterogeneous Non-catalytic Reactions forming solid, liquid and gas products. The different product phases depend on the temperature present in the system. In this work we present dynamic model of the Vapor Recovery Unit of a conceptual Carbothermic Aluminum Process. Because of the complexity of the system several models are developed and coupled to capture the essential physics of the multiphase reaction problem. A Shrinking Core Model describes the reaction mechanisms. Then material and energy balances are coupled with the thermodynamics properties from the FACT database of thermodynamic properties, resulting in a system of nonlinear Partial Differential Equations. In the paper we describe the model development and governing equations for the reaction mechanisms and fluid flow. Finally we review the numerical schemes created for the solution of the model system. The model can be used for control and design purposes.IntroductionThe Carbothennic Processes for producing Aluminum can be divided into two groups (Motzfeldt et al. (1989)) In the first approach pure alumina is produced and reduced to pure aluminum. In the second approach an alloy (e.g. aluminum and silicon) is made and then aluminum is produced from the alloy. The history of both processes has been described by Ginsberg et al. (1965). At least three aluminum producers began largescale testing of this process in the 60's Alcan, Pechey-Ugine and Reynolds. Alcoa did some smaller scale experiments.Alcoa was one of the first companies to produce aluminum by Carbothennic Reduction (Foster et al. (1956)) and US Patent 2,829,961 April 8, 1958. In this process a carbon containing molten aluminum phase was a floated on top of an oxy-carbide melt. During the cooling the dissolved carbon deposited as aluminum carbide. The carbide was then separated from the molten aluminum by a fluxing agent. This process was successful but economic unfeasible."

Jan 1, 2001

By J. H. Viljoen, A. Heyns, J. F. Morrison, C. H. Wyndham, N. B. Strydom

Discussion M. J. Martinson* (Associate Member): This is another interesting paper in the series which the Human Sciences Laboratory is publishing on the physiological cost of the more strenuous manual tasks performed underground. As a mining engineer-albeit presently an academic one -this contributor is more concerned with the practical significance of the study in the field of stope cleaning than with physiological niceties, but before discussing some of the practical issues raised by the paper perhaps the authors would care to reply to lay comment on three physiological matters. Firstly, in two places the authors make statements to the effect that the maximum oxygen intake of 'average' (sic) Bantu mine workers is 3.0 l/min. What do the authors mean by 'average'? Maximum oxygen intake in the individual is probably some function of inter alia age, physical fitness, state of health, ambient partial pressure of oxygen, diurnal and/or seasonal changes in metabolism, and possibly cumulative exposure to dust and other occupational contaminants. Since maximum oxygen intake is apparently such an important quality in manual labourers we ought to have a clear picture of its distribution in the entire labour force, and also know precisely how the individual's quantum is affected by factors such as those mentioned above. Secondly, arising out of the same statements and ignoring the reservation implicit in the previous paragraph, is it correct to say that the 'average' Bantu mine worker has a maximum intake of 3.0 l/min? In the August 1966 issue of the South African Journal of Science four of the present co-authors reported the mean maximum oxygen intake of a random sample of 338 Bantu recruits of different tribes to be 2.63 l/min with a standard deviation of 0.542 l/min, and these figures were repeated in a paper published in the November 1968 issue of this Journal. Admittedly the mean maximum oxygen intake of the six subjects used in the present study was 3.05 l/min, but since they were selected on the grounds of previous shovelling experience they can hardly be regarded as being 'average' recruits. Thirdly, it seems to me that the authors are perhaps a little uncritical in their acceptance of the '50 per cent of maximum oxygen intake' level of activity for endurance work. I am not unmindful of the evidence upon which this level is based, but I suggest that the evidence is at best tenuous and that the whole topic of fatigue and 'optimum' levels of productivity under conditions of high muscular activity and considerable psychological stress is a lot more complicated than would appear from the authors' ready acceptance of the 50 per cent level. Under present working conditions the question is largely rhetorical because it would need an army of supervisors to ensure that all members of a typical gang work at 'optimum' levels throughout the shift, but if individual performance should ever become more readily determinable the issue might become crucial to management and malayisha alike. So much for physiological matters; now a few random thoughts on some wider, practical issues raised by the paper. In the paragraph headed Material the statement is made that 'The mixture (of fine, medium-sized and bigger rocks) was considered to be representative of an average underground rock sample'. Elsewhere in the report the authors specifically draw attention to the effect of particle size on the oxygen consumption of men shovelling graded material, and intuitively one imagines that the size distribution of the material being shovelled would be highly significant in a study such as this. Presumably the authors were forced to assess size distribution subjectively because of the lack of objective data on the subject, and possibly the necessity for this assumption highlights how little we know quantitatively about any of the variables in stope cleaning systems. In this connection it may be remarked that although the present study was largely designed to show how dip and stoping width effect energy expenditure in shovelling, no data are given-nor, probably, are they available-to show how the industry's stoping tonnage is distributed in terms of these two factors. It seems to me that if the mining industry seriously hopes to improve stope productivity it must start by measuring the basic variables in existing systems. Elaborating somewhat on the previous paragraph, there also seems to be a tremendous gap between the present study-and its predecessors-and the prospect of gainfully using the information so carefully garnered by the authors. It would be reassuring to hear from the authors that their work on the physiological aspects is being integrated in some master plan for increasing productivity of manual labour. This I fear is not the case, and if productivity has changed at all in recent years I would hazard a guess that the change has been brought about by random factors rather than by systematic engineering design. The Human Sciences Laboratory has worked extensively in stopes in the past, and possibly the time has come when it should widen the ambit of its operations to include engineering-type analyses of cleaning systems, with particular emphasis on the economics of rapid cleaning by manual labour. Perhaps experiments could be conducted with stakhanovite-type gangs consisting of men selected for their high maximum oxygen intake and superior motivation; these men might be offered special incentives in the shape of extra pay

Jan 10, 1969

By Lisa E. Helberg

"Titanium tetrachloride is produced through the chlorination of a variety of titanium bearing ores, some occurring in nature, and others enriched in titanium content by a variety of ""beneficiation"" processes. The chlorination step can produce a variety of metal chloride impurities, such as iron chlorides and vanadium chlorides, which must be removed from the TiC14 before it can be used to produce pigmentary TiO2, titanium metal or for any other commercial use. The requisite manipulations involve both physical and chemical separations in a multi-step process. The history of various purification strategies will be discussed.TextThere are a wide range of titanium-based products available, all of which start with titanoferrous ore of some type. Two main routes are used to convert ores into products, known as the sulfate and chloride processes. The sulfate process uses sulfuric acid to digest the ore, separate the impurities, and then precipitate titanium dioxide from the resulting titanyl sulfate (TiOSO4) via metatitanic acid. This process can also supply TiOS04 for other applications."

Jan 1, 2011

By R. L. Crosby, L. W. Higley

Magnesium- rich magnesium- aluminum- zirconium alloys in the cast and in the extruded and heat- treated condition were studied to identify the phases present and to determine phase distribution . In cast alloys , two intermetallic compounds were identified : ZrAla by X- ray diffraction ; and Mg₁ Al₁₂ by microscopical observation . Based on microscopical comparisons between the known phases in the cast structures and the phases in the structures of extruded and heat - treated rods , ZrAl₂ and Mg1 , Al12 were identified in the structure of the latter . The presence of these intermetallic compounds in rod specimens could not be confirmed by X- ray diffraction . ZrAl₂ was observed in the structure of extruded and heat - treated rod specimens containing as little as 0.01 weight - percent zirconium . The presence of aluminum restricts the solubility of zirconium in magnesium because of the strong tendency to form ZrAla . This intermetallic compound segregated in clusters of small particles in the matrix of cast alloys , and only slight improvement in distribution was noted when the alloying techniques were varied .

Jan 1, 1964

By J. C. Beidelman

One of the oldest settled portions of Canada is that "strip of land" extending into the Gulf of St. Lawrence, known as the Gaspe peninsula, with the Bay of Chaleur on its southern boundary. This "strip of land" is still so very sparcely populated that only at a few places does settlement extend more than a few miles from the coast. ? The peninsula is 160 miles long, 75 miles wide and with the exception of the above mentioned settlements is a mountainous wildness-void of all roads or inhabitants. Developments in the interior, of all nature, out-side of the cutting of timber by limit holders, was entirely lacking until the year 1915, when mining was first commenced. In the summer of 1844 Sir William Logan made a preliminary survey across the peninsula, from Cape Chat on the Gulf of St. Lawrence to Cascapedia on the Bay of Chaleur, passing through a country ?of which very little was known at that time. After a rather rough trip to the headwaters of the Grand Cascapedia river, Logan's party descended this river to its mouth, passing ten miles west of what is now known as the Federal mines. There is no record of Logan, or of any of his party, finding zinc or lead ores of any character on their journey across the peninsula, and until 1909 no precious or base metals were discovered within reasonable distance of Logan's survey.

Jan 1, 1924

By T. SPOLAN, G. W. Jones, R. E. Kennedy

Information relative to the explosibility of acetylene at elevated pressures and means of handling acetylene safely under these conditions is of considerable interest at present. American practice limits the pressure at which acetylene may be generated and distributed to poiIits of' use. The pressure in portable acetylene generators is 15 pounds per square inch gage. Tests made by the Bureau of Mines have shown that 15 pounds per square inch gage is too high to prevent explosiofiS of gaseous acetylene in the absence of air; in fact, dry acetylene gai can be exploded at pressures greater than 5.9 pounds per square inch gage. The Bureau has been interested in the explosibility of acetylene for many years because of its continued: use for illumination in many metal mines and its general use in cutting 1illd~--eldifigoperations in the mining maus-try.

Dec 1, 1948

By H. Kosmider, P. Coheur

New processes of blowing with an oxygen-enriched air or gas mixtures of oxygen and steam allow the steelmaker to produce, in a basic converter, a rimmed steel low in nitrogen (0.0020 pct), phosphorous (0.020 pct), and sulphur (0.020 pct). The physical properties (ductility) of the new steels are excellent. Furthermore, from the point of view of economy, these new methods of blowing offer outstanding possibilities. THE natural occurrence of geological deposits of iron ore and local economic circumstances led European blast furnace men to work large quantities of lean iron ore with a phosphorus content as high as 0.5 pct. The iron obtained from these ores generally contains 1.5 to 2.1 pct phosphorus, 3.6 to 3.9 pct carbon, 0.3 to 0.6 pct silicon, 0.04 to 0.08 pct sulphur, and 0.3 to 1.2 pct manganese. To produce steel from this pig iron, the steelmaker has at his disposal several processes. One of the simplest and most economical is the pneumatic process developed by S. G. Thomas in 1879. This process of steelmaking, called the Thomas process, consists of blowing through the bottom of a basic bessemer converter and is used widely in Western Europe, as shown in Table I. Due to the development of tonnage oxygen plants, this process has become more important because the use of oxygen offers new possibilities of steel manufacture. Not only may the quality of the steel be improved, but liquid pig iron also may be used, the composition of which does not meet the heat requirements of the blow with atmospheric air. It is not intended to present here a detailed scientific discussion of the basic bessemer process but rather to discuss briefly its industrial possibilities in the case of rimmed steel and when blowing with atmospheric air, oxygen-enriched air, or gas mixtures of oxygen and steam. This paper is based on the current practice at Klockner-Hüttenwerk Haspe's steel division, and at six Belgian and Luxemburg steel works. The latter are members of the Liege section of the C.N.R.M. (National Institute for Metallurgical Research) and are: ARBED, John Cocker-ill, Esperance-Longdoz, HADIR, Miniere et Metal-lurgique de Rodange, and Ougree-Marihaye, most of which are working with tonnage oxygen plants.' In order to avoid any misunderstanding, it should be noted that most of the techniques to be men- tioned, or similar ones, are used currently at many steel plants in Western Europe. Background The basic converters used in Europe have a capacity of 17 to 65 tons of steel, and are similar in shape to the one in Fig. 1. The lining is brick or rammed dolomite and has a life of 250 to 500 blows. The bottom is rammed dolomite and has a life of 40 to 80 blows. As far as we know, the type of blast used does not appear to have any influence on the life of the lining. Bottom life, on the contrary, depends very much upon the composition of the blast. It is only when

Jan 1, 1955