Search Documents

By C. J. Chindgren

Two air classification systems were built and tested as separatory devices for recovering the nonferrous metal values from shredded automotive nonmagnetic reject scrap. A horizontal air system with a capacity up to 16 tons per hour was used to obtain preliminary separations, and a smaller capacity vertical system was used as a cleaning device. Shredded automobile reject material containing aluminum, copper, and zinc values of about $55 per ton were air-classified in the horizontal elutriator. Ninety-six percent of the metal was recovered in a 74-percent metal concentrate. Tandem operation of both classifiers recovered 92 percent of the metal in an 80-percent concentrate while rejecting 87 percent of the nonmetallics. Heavy media separation of the air-classified concentrate produced an overall recovery of 91 percent of the metal in the form of a 99-percent metal concentrate.

Jan 1, 1971

By D. W. Agers

This paper is an extension of previous work evaluating a new extractant, LIX®-64, for recovery of copper from dilute acidic solutions. Large scale pilot plant operations have confirmed the technical and economic feasibility of the process and, with minor exceptions, scale up parameters obtained by previous laboratory work. Operating problems encountered in the pilot plants are discussed. Design parameters for-scale-up to commercial plants are presented and discussed along with a revised capital cost estimate. The future pilot program is discussed, including minor design changes and the effect of entrained organic on dump leaching efficiency.

Jan 1, 1967

By S. F. Shaw

IT IS generally recognized that the natural gas absorbed in petroleum plays the leading r6le in moving the oil through the sands to the well and supplies the energy that delivers the oil to the surface when the wells are flowing. It is the purpose of this paper to note the amount of oil that could be lifted by this gas if 100 per cent. efficiency were obtained and the efficiencies actually obtained in the use of this gas. An article in MINING AND METALLURGY,' stated that in a Wyoming field, with a pressure of 300 lb. per sq. in., there would be absorbed 65 cu. ft. of gas per barrel, or 1.55 cu. ft. per gal. of oil. The writer does not know if data have been obtained, by experiment, for pressures beyond those indicated in this article, therefore, for the purpose of illustration, he has projected this curve to obtain figures for pressures greater than 300 lb., although probably experiment will show that the extended line is not quite correct.

Jan 1, 1926

By B. W. Naugle

A small-scale laboratory coke oven similar to those described by Swiniarski, Cryan, and Altieri and Fuchs, Sandhoff, Taylor, and Gauger was built by the Bureau of Mines in 1943. Tests made since that time have indicated that such a small oven is of questionable value in predicting the coking pressures to be expected in commercial coke ovens. This summary of the work done has been prepared at the suggestion of the Advisory Committee to the Bureau of Mines-American Gas Association Survey of Carbonizing Prop¬erties of American Coals.

Jan 1, 1948

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock. The first stage of the study was the recognition of the rock blast process in question, assessing key parameters that characterize this whole operation: geomechanical characteristics of the rock mass, implementation quality for drilling pattern and explosives charging (collar position, hole depth, explosive charge length and stemming size) and recognition of current blast designs. The central element of this study was the creation of a vibration attenuation and seed wave model which has allowed the characterization of this particular rock mass present in a region determined by the Minas-Rio team. The model is based on a near field vibration test, constituting a powerful tool in the design of blast parameters. The blast design developed from the damage model simulations basically modified the timing and sequencing. The aim of this study was to improve the fragmentation resulted by the blasting, considering the particle size requirements demanded by the primary crusher and to increase the productivity of the loading and hauling operations. The results were analyzed considering the effective productivity of the two different fleet types of shovels, where the authors have analyzed more than 46000 values of productivity from September 2017 to August 2018, taken from the Dispatch system. A significant increase in effective productivity of these load equipment was observed, 7% to the PC4000 fleet and 2% to the PC5500 fleet, values supported by statistical parameters and hypothesis tests.

Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. Since 1980, Australia's share of the world's output of these minerals has fallen. Exhaustion of known resources, together with the changing composition of new deposits, is expected to result in Australia's share of the rutile and zircon output continuing to decline. Its role as a major supplier of upgraded ilmenite, that is synthetic rutile, is expected to increase. In 1994, the Bureau of Resource Sciences assessed Australia's demonstrated resources of mineral sands as follows: rutile 14.4 Mt, ilmenite 132.5 Mt, and zircon 21.0 Mt. These resources are located along the coast of Queensland and New South Wales, in the Murray Basin of New South Wales and Victoria, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth. However, some 45 per cent of rutile and zircon resources along the coast of Queensland and New South Wales are not available for mining because of environmental concerns. World demonstrated resources are estimated at 40 Mt (contained TiO2) for rutile, 50 Mt for zircon and approximately 312 Mt (contained T1O2) for ilmenite. Outside of Australia, the most important resources of rutile, ilmenite and zircon are in South Africa (rutile, zircon , and ilmenite in the form of titania slag), Sierra Leone (rutile), India (ilmenite, zircon and rutile), and Canada (hard rock ilmenite). Significant resources of ilmenite occur in Madagascar and Mozambique.

Jan 1, 1996

By See G. T

Bentonites and fuller's earths from seven localities in N.S.W. have been analysed with respect to occurrence, mineralogy and physical properties and areas for future prospecting have been indicated.INTRODUCTIONThe rapid expansion of Australian industry in the postwar years has been accompanied by an ever increasing demand for fuller's earth and bentonite, but in New South Wales at least the demand has been met principally by imports. However, some local and generally inferior active earths have been won to blend with imported materials to reduce costs. The important discovery of the widespread distribution of bentonite clays in the Northern Coal Measures, made recently by Grim (Booker, 1956), has givenimpetus to the further search for material comparable in quality to the imported active earths.Bentonite may be defined as a highly plastic clay, generally possessing swelling properties, composed essentially of montmorillonite and derived from the alteration of volcanic ash. Fuller's earth refers to any clay which, with or without chemical treatment, is capable of decolourizing mineral or vegetable oils and is, therefore of economic value. Montmorillonite is the active component of most fuller's earths, though palygorskite-, halloysite- and even kaolinite-rich clays have been used.Previous literature related to the New South Wales deposits has been confined to general descriptions and little technical data beyond an occasional chemical analysIs have been available. Bentonites and fuller's earths from seven...

Jan 1, 1959

By D. B. Dow

The study of oil production methods with reference to the amount of oil originally pressent in the oil-bearing, formations has developed the fact that-ordinary methods-of production remove only a part of the oil actually present. In fact, it is generally realized that when a field is abandoned more oil remains in the sand than has ever been removed. As a consequence of this realization, the petroleum engineer has devoted considerable tine in recent years in devising methods for increasing the percentage of recovery. His studies have indicated that in most cases the total production of a field is dependent upon the available gas rather than upon the available oil. Mien the gas in the sand is exhausted, oil production ceases even though there may be enormous quantities of oil remaining unrecovered. Consequently, any method of conserving the gas or increasing the supply of gas will increase the ultimate recovery from a field. The practice of producing oil under vacuum increases the effectiveness of the gas remaining in the sand, as well as furnishing more gas by evaporating the light fractions of the crude. Pumping ' compressed gas or air down selected wells of a lease has been found to increase the production of oil from the surrounding wells. Studies of oil and gas ratios have indicated that much of the available gas has been wasted as far as its effectiveness on oil production is concerned. his has led to the development of "stop cocking"3 and the practice of producing under back pressure3, which methods aim, to obtain more effective work from the gas with reference to the amount of oil delivered to the well.

Jan 1, 1926

Geological discontinues in the coalbed, such as faults, sandstone channels, permeability facies, lithotype changes, and large scale partings in the coal seam, can cause intermittent production problems or produce unexpected amounts of water or gas from degasification boreholes. These discontinuities not only can impact methane emissions into the mine workings, especially if they hinder proper and effective degasification of the coalbed but may act as conduits for methane flow from gassy strata into advancing mine workings. The effects of these discontinuities are still under debate by mining and gas production experts. This study presents a numerical investigation using reservoir simulations of the effects of partings and permeability facies and lithotype changes on the production performances of vertical and horizontal degasification boreholes, as well as the emissions during longwall operations. In this work, the grid block was designed in a multi-layer 3-D structure which enabled spatial descriptions of the geometries and properties of the discontinuities within the coal seam. The studied coal seam discontinuities and their properties were distributed arbitrarily within the model. Production was simulated by vertical and horizontal boreholes. Degasification boreholes operated two years prior to start of the mining. The results of this numerical study show that in coal seams with major heterogeneities and discontinuties, the geometry and location of the boreholes are important for improved gas production. These considerations are also important for controlling methane and water inflow into the working environment during longwall mining.

Jan 1, 2008

By Niko Hellstén

To capture efficiently the valuable trace metals from nickel slag using electric furnace, it is important to study their distributions between the slag and metallic phases in the furnace. It is impossible to calculate accurately these distributions without experimental measurements. Therefore, in this work, selected trace metal distributions and phase equilibria between K2O containing iron-silicate slags and a metallic Ni-Fe-Cu alloy in nickel slag cleaning furnace conditions were studied. The experimental method developed and applied during the work, involved a modified quenching technique that included equilibration of the samples in semi-sealed quartz ampoules in an inert atmosphere and metallic Fe saturation. The use of the semi-sealed quartz ampoule prevents the escape of volatile elements from the sample during equilibration. Chemical compositions of the phases and the trace elements were analysed by EPMA. From the measured compositions, the trace metal distribution coefficients between the molten Ni-Fe-Cu alloy and slag were calculated.

By R. L. Grayson, S. Yuan

A stochastic model for evaluating the impact of the reliability and maintainability of shovels and trucks on the operational effectiveness of shovel-truck mining systems is presented. In the model, the Markov modeling technique is used to analyze the operating status of a shovel-truck mining system. Then, simulation is used to study the productivity of a shovel-truck system in a particular state. Finally, the relationship between the effectiveness of a shovel-truck system in terms of productivity and the reliability and maintainability of equipment is established. This relationship may be very useful to mine managers in making decisions in surface mining (e.g., regarding production process control, equipment replacement, and maintenance planning). A quantitative study is given to demonstrate how the reliability and maintainability of equipment affect the system effectiveness and how to pinpoint the parameter that has the most significant effect on the system effectiveness. The quantitative study indicated that in order to improve the system effectiveness significantly, the reliability and maintainability of the equipment need to be improved simultaneously.

Jan 1, 1995

By Y Li, Z Fu, D J. Williams, E Topal

Mine waste rock is unavoidable in the recovery of ore by open pit mining methods. Effective management of waste rock movement covers the removal and placement of the waste rock, generally in a surface dump in the most cost-effective way while satisfying the long-term environmental expectations. Since the 1960s, there has been significant research carried out into planning of ore movement from open pit mines such that the overall net present value (NPV) of the project can be maximised. Currently, several software packages are available to achieve this task as a common practice within the mining industry. However, planning of mine waste rock movement is still achieved manually, as the available software does not consider optimal waste rock movement and dump design. This paper describes a tool to optimise waste rock placement, which minimises the haulage cost while creating environmentally friendly waste rock dumps through selective placement and encapsulation of the reactive waste rock in the dump. The embedded methodology in this tool has been developed based on the mixed integer programming (MIP) modelling technique to optimise the waste rock movement. The methodology provides an easily-manipulated and fully-automatic tool for professionals to complete waste rock dump scheduling in four main steps: data input, model construction, model computation and solution retrieval. The application of the new tool into a real case project in this paper shows that it can determine economically and environmentally optimised waste rock dump schedules in an acceptable time frame.CITATION:Fu, Z, Li, Y, Topal, E and Williams, D J, 2015. A new tool for optimisation of mine waste management in potential acid forming conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By Walter Díaz Cartagena

El suelo es uno de los recursos más importantes del agua -en tanto sustenta la vida natural y fuente de alimento para toda la especie terrestre. Por tal motivo, el presente texto señala los planes y estrategias para el cumplimiento de los estándares de calidad (EKA) de los suelos. En la promulgación de D.S. N°02 2013-MINAM que aprueba dichos estándares, se establece el último componente por norma para conocer la cantidad de contaminación del suelo. Este decreto propone una serie de etapas en la gestión de suelos contaminados que van desde la ecuación de los instrumentos de gestión ambiental, la investigación de situación de estos suelos contaminados en la zona de producción para determinar el estado en el que se encuentran y la recuperación ambiental por parte de un plan de descontaminación de suelos.

Jul 1, 2014

By A. Paul Bond

Two series of 17pct Cr iron-base alloys with small, controlled amounts of carbon and nitrogen were vacuum-melted in an effort to detertmine the meclz-uniswls of inter granulur corrosion in ferritic stain-less steels. An alloy containing 0.0095 pct N aid 0.002 pct C was very resistant to intergranular corrosion, even after sensitizing heat treatments at 1700" to 2100o F. However, alloys containing more than 0.022 pct Ni and more than 0.012 pct C were quite susceptible to intergranular corrosion after sensitizing heat treatments at temperatures higher than 1700°F. This corrosion was observed after the usual exposure tests and after potentiostatic polarization tests. Electronmicroscopic examination of the alloys susceptible to intergranular corvosion revealed a small grain boundary precipitate; this precipitate was absent in the alloys not susceptible to such corrosion. Thc electronmicrographs indicate that intergranu1ar corrosion of ferritic stainless steels is caused by the depletion of chromium in areas adjacent to precipi-tates of chromium carbide or chromium nitride. It also seems likely that the precipitates themselves are attacked at highly oxidizing potentials. Confirma-tion of the proposed mechanisms was obtained in tests on air-melted ferritic stainless steels containing titanium. The titanium additions greatly reduced susceptibility to intergranular corrosion at moderately oxidizing potentials but had no beneficial effect at highly oxidizing potentials. A major obstacle to the use of ferritic stainless steel has been their susceptibility to intergranular corrosion after welding or improper heat treatment. It appears that sensitization of ferritic stainless steel occurs under a wider range of conditions than for austenitic steels. In addition, a greater number of environments lead to damaging intergranular corrosion of sensitized ferritic stainless steels than to sensitized austenitic steels. The chromium depletion theory of intergranular corrosion is widely accepted for austenitic stainless steels'" although there: are some objections.3 On the other hand, several alternative mechanisms proposed for ferritic stainless steels include precipitation of easily corroded iron carbides at grain boundaries,' grain boundary precipitates that strain the metal lat-tice,5 and the formation of austenite at the grain bound-arie.6 The application of the chromium depletion theory to ferritic stainless steels has been discussed extensively by Baumel.7 The present investigation was undertaken to determine which of the proposed mechanisms can be sub- A PAUL BOND IS Research Group Leader, Climax Molybdenum Co of Michigan, Ann Arbor, Mich. stantiated with experimental data obtained on ferritic stainless steels. High-purity 17 pct Cr alloys containing small controlled additions of carbon or nitrogen were therefore prepared, and then examined electro-chemically and metallographically. EXPERIMENTAL PROCEDURES Materials. Two series of experimental alloys were prepared from electrolytic iron and low-carbon ferro-chromium using the split-heat technique. In this technique, the base composition is melted, and part of the melt is poured off to produce an ingot. To the balance of the melt, the required addition is made and the next ingot cast. This process is repeated until a series of the desired compositions is cast. By this procedure the impurity levels are essentially constant within each series. All the alloys in the carbon-containing series were melted and cast in vacuum. The base composition in the nitrogen series was melted and cast in vacuum; subsequent ingots in the series were melted with additions of high-nitrogen ferrochromium, and cast under argon at a pressure of 0.5 atmosphere. Two additional alloys were produced starting with normal purity materials. They were induction-melted while protected by an argon blanket and cast in air. Table I gives the composition of the alloys. The 2-in.-diam ingots produced were hot-forged and hot-rolled to a thickness of 0.3 in. and then cold-rolled to 0.15 in. All specimens were annealed at 1450°F for 1 hr. The indicated sensitizing heat treat-s s ments were performed on annealed material. All heat treatments were followed by a water quench. Specimen Preparation. For the 65 pct nitric acid test, 1 by 2 by 0.14-in. specimens were wet-surface ground to remove surface irregularities and polished through 3/0 dry metallographic paper. For the modified Strauss test, $ by 3 by 0.14-in. specinlens were similarly prepared. Immediately prior to testing, the Table I. Compositions of the Alloys Composition, pct Alloy Cr hio C N 270A 16.76 0.0021 0.0095 270B 16.74 0.0025 0.022 270C 16.87 0.0031 0.032 270D 16.71 0.0044 0.057 271A 16.81 0.012 0.0089 27 IB 16.76 0.018 0.0089 271C 16.69 0.027 0.0085 271D 16.81 0.061 0.0O71 4073' 18.45 1.97 0.034 0.045 4075† 18.5 2.0 0.03 0.03

Jan 1, 1970

By Ernst Lindemann

The SMS group has developed the ultrasound technology “HD scan” for inspection of the internal quality of as-cast products. This method of sample analysis requires less preparation work and is safer than the current, most common technique of etching and/or sulphur printing. Furthermore, this technology offers a three-dimensional view into the sample of the cast product and thus more representative information for a better quality evaluation. The internal quality evaluation can be performed automatically and objectively by software based on clear statistical methods. A quantitative centerline segregation rating can be assigned to each sample, based on the size and distribution of segregates detected by the unit. Internal crack statistic (length, position, orientation, etc.) and narrow side profile can also be measured. Grain macrostructure can also be visualized which allows for a potential optimization of casting parameters like strand cooling, soft reduction or electromagnetic stirring. The accuracy of the new method was proven by parallel metallographic investigations of more than 100 samples of different steel grades and sample shapes. Automatic defect evaluation and classification was compared against macroetching results. It was found that HD scan identified more defects and the visualization of the macro structure could be performed in more cases than with macro etching. All tests, comparisons, further developments and analyses for various steel producers and steel treatment companies have been conducted at the HD scan unit, located at the SMS group headquarters in Düsseldorf, Germany (Figure 1). Based on the results, SMS group has designed a unit which can be used in industrial scale.

Aug 17, 2017

By P D. Franzmann, D J. Readett, J Peterse

A better connection between laboratory- and pilot-scale test results, and heap bioleaching performance can be achieved by generating reliable information on the fundamental microbial, chemical and physical processes that occur in heaps and incorporating this information into a comprehensive and robust model. More efficient heap bioleaching, particularly of chalcopyrite, has the potential to add value to the mining industry as well as deliver attractive environmental and social benefits to the communities within which those companies operate.The results of fundamental chemical and microbiological studies of the leaching mechanism, the temperature dependence of chalcopyrite bioleaching, and the optimisation of leaching conditions are described with examples from full-scale heaps. The development and application of a number of novel techniques and tools has assisted our understanding of heap subprocesses mineralogy, hydrology, chemistry and microbiology. The heap bioleaching model HeapSim, which embodies a large number of effects not previously accounted for in other models, continues to be refined and has been applied successfully to the study of several heap bioleach systems.

Jan 1, 2004

By FREDERICK J. ALCOCK

THE high prices which lead and zinc have commanded during recent months have given a great impetus to search for workable deposits of these metals, and there has accordingly risen a demand for information about deposits which have been worked in the past and which might possibly be opened up anew under these more favorable conditions. Production of zinc and lead in Canada has been on the increase during the last few years. In 1924, 175,- 485,499 lb. of lead with a computed value of $14,221,- 345 were mined. Of this, 96 per cent. was produced in British Columbia, 3 per cent. in Ontario, while Quebec and the Mayo district of the Yukon accounted for the remaining one per cent. During the same year the production of zinc amounted to 98,909,077 lb.. valued at $6,274,791. Of this 96,000,069 lb. were produced in British Columbia and the remaining 2,909,008 in Quebec. The large producer of zinc and also of lead is the Sullivan Mine at Kimberley, B. C. In comparison with the Sullivan, the deposits which are known to occur in eastern Canada are relatively small. Two, however, the Kingdoll lead mine at Galetta, Ontario, and the Tetreault zinc property at Notre Dame des Anges, Quebec, are steady producers. The object of this paper is to describe briefly these and other deposits of eastern Canada, to show their relation to geological events and to point out what are the chances of any of those which are idle at present developing into active producers or what are the possibilities of new deposits being discovered.

Jan 1, 1926

By Moussa Wone, Martino Scialpi, Colin LaVassar, Carlton Ray

The Potomac River Tunnel (PRT) is the next major phase of the DC Clean Rivers Program. The design-build PRT project includes a 5.5-mile-long, 18-foot-internaldiameter tunnel, seven shafts, and two underground connections to existing structures. Major challenges include tunnel boring machine (TBM) excavation though mixed-face conditions within a buried paleo-channel and an approximately 1,350-foot-long rock/ soil transition zone; construction beneath the elevated Whitehurst Freeway; tunneling beneath an existing luxury residential building and existing transit tunnels with limited clearance; and complex coordination with a variety of federal, regional, and local stakeholders. This paper describes the overall project scope, geotechnical conditions along the alignment, and primary design/construction challenges and mitigations.

Jun 13, 2021

By James P. Connell

HISTORICAL BACKGROUND The American Concrete Institute defines shotcrete as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity onto a surface." This definition thus includes what is traditionally known as gunite, which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this chapter. In 1914, following the invention of the mortar gun in 1907, then chief engineer of the US Bureau of Mines (USBM) George Rice developed the gunite process for underground test work at the USBM facility at Bruceton, PA. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto tunnel in California. The greatest development was in Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Initially, shotcrete was used to reduce manpower requirements for forming and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately after the opening had been made. The incorporation of wire mesh into the shotcrete led to the new Austrian tunnel method or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the US reliance on wood or steel supports in main-line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to accept the new and seemingly unrealistic lighter shotcrete support. APPLICATION REQUIREMENTS Shotcrete is a relatively new material for use in underground support systems. Consequently, experienced miners are not always available who are capable of applying the material effectively. Shotcrete, particularly in the small cross sections typical of mine shafts or haulageways, is applied in cramped quarters under less than ideal conditions. Adequate lighting should be made available. The surface should be clean and free of running or dripping water. It may be necessary to collect flowing water in plastic pipes or water collection devices. Any dry cement dust from previous shotcrete applications should be washed from the surface in order to assure a good bond. The US Bureau of Reclamation (USBR) while shooting test panels at the Cunningham tunnel in 1974, found that experienced shotcrete operators were able to obtain up to three times greater compressive strengths than were obtained by unskilled operators using the same equipment and shotcrete mix. ENVIRONMENTAL AND SAFETY REQUIREMENTS Since sodium and potassium hydroxide, as well as other moderately toxic compounds, are often contained in shotcrete (particularly where accelerators are used), safety precautions must be taken to prevent skin and respiratory irritation. Nozzlemen and helpers are required to wear gloves, protective clothing, and ventilation hoods with a filtered air supply. Respirators approved by USBM, equipped with chemical filters that will not pass the caustic mists, may be permitted in lieu of hoods if goggles or safety glasses are worn. Protective ointments are available to reduce skin irritation. All air and shotcrete feed hoses should be equipped with safety-type couplings and secured with safety chains at each coupling to prevent whipping in the event of a hose or coupling failure. Some environmental effects can take place down-stream from the development face being supported. The accelerator compounds, as well as the portland cement used in the shotcrete, will be found in the rebound material which falls to the invert of the heading. Since these compounds may be leached from the rebound material and carried by the drainage system, it may be necessary to install neutralizing or other water treatment facilities. Investigations may find that the final reaction with other compounds being leached from the mining operations may result in a more or less environmentally acceptable end product. USES OF SHOTCRETE General Uses Shotcrete, as a combination of cement, aggregate, and accelerator, is utilized for underground openings such as shafts, adits, haulageways, and service chambers for the following general purposes : (1) primary sup¬port; (2) final lining; (3) protective covering for excavated surfaces that are altered when exposed to air (the protective covering may be of a temporary or final nature); (4) protective covering for steel or wooden supports, rockbolts and rockbolt plates, heads, nuts, and other mats, including wire fabric, used to prevent rock-falls; and (5) as a lagging material in place of timber, steel, or concrete between steel or wooden supports. These applications can be grouped into three general use categories: shotcrete used as a rock sealant, shotcrete used as a safety measure, and shotcrete used as a structural support. Use as a Rock Sealant Thin applications of shotcrete can reduce or prevent slaking of shales or other rocks that are altered when exposed to the wetting and drying cycles created by mine ventilation circuits. While shotcrete may be effective in preventing such rock alteration, at the present time it is not as economical or efficient as other commercial sealants. However, if the sealant property can be incorporated into the structural support capability, the added contribution is usually helpful. Thin applications are not usually sufficient if the alteration of the

Jan 1, 1982