Search Documents

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By John C. Franklin

INTRODUCTION Alpha-emitting radon daughter products are a recognized health hazard contributing to the development of lung cancer in persons exposed to excessive concentrations over an extended period. The primary control technique used by the mining industry is dilution with fresh air. Because the uranium is deposited in porous sandstone in most U.S. mines, the control of this hazard with dilution requires excessive volumes of air. As the mines become larger and deeper, the cost for ventilation becomes a major expenditure for the mining industry Most mines are maintaining levels of radon daughters lower than required by law but to maintain these present levels the mining companies are going to be drilling more vent holes or using other control techniques as the mine expands. These control techniques are being investigated by the U.S. Bureau of Mines to determine their effectiveness, cost, and safety for underground use. [Instrumentation] The Bureau's early research used batch sampling of both radon and radon daughters for determining the concentrations. In both cases it was determined that batch sampling did not give a complete understanding of what was happening to the concentrations. Therefore, continuous monitoring systems were developed for both. A continuous flow-through radon monitor was developed by the Bureau (Franklin, et al.., 1976) using a modified Lucas flask mounted on a photo-multiplier-tube (PMT). The air was filtered twice prior to entering the flask to remove dust, diesel smoke, moisture, and radon daughters. The signal from the PMT was then inverted, shaped, and driven to a data acquisition system (DAS) which accumulated the signals. The DAS has two comparators for setting the scan time and interval, a 24-hour clock with Julian date, a printer, and a perforated paper tape punch. Sampling time is determined by the type of experiment being conducted. Our normal sampling time is one 10-minute scan every 15 minutes, but could be set as low as one scan every minute or as long as a 16-minute scan every 167 minutes. There are two models of the DAS. One is a 10-channel system and the other a 30-channel system. On a 10channel system normally 6 channels are used for radon and radon daughters and the other four channels are used for temperature, absolute pressure, air velocity, and relative humidity as described by McVey (1977). Figure 1 shows a scan of five channels monitoring the radon concentration from intake to exhaust in a stope for a non-work day. If the radon concentration stayed this constant during work days, then continuous monitoring would not be necessary. [ ] Droullard (1977) developed a continuous alpha-beta monitor. This monitor has been modified so that it can be used with the DAS previously mentioned. Control Techniques The U.S. Bureau of Mines has conducted research in controlling airborne radon/radon daughter for 10 years. Major efforts have been conducted in sealing the rock to prevent the release of radon, bulkheading to seal nonproductive areas, backfilling with classified mill tailings, and positive pressure ventilation. Also, tests have been conducted to determine the mining cycles contribution to the radon problem. Surveys One stope with two intakes and one exhaust was continuously monitored to determine the effects of blasting, mucking, and drilling on the airborne radon concentrations (Franklin, et al., 1976). Two other detectors were located inside the stope which were close to the mining activity. In this stope no appreciable change in radon was observed during drilling holes for blasting and roofbolts. This study showed increases up to 40 percent in radon for slushing in the exhaust drift. The radon remained high and very eratic during slushing, as can

Jan 1, 1981

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

IN the ordinary course of treatment of pyritic ores or concentrates, whether for the recovery of copper, tin, gold, or any other contents, the removal of some or all of the sulphur contents is almost invariably the first step. The practice is to roast the ore in a current of air so that the sulphur is oxidized to sulphur dioxide and the metal constituents are changed from sulphides to oxides. If it is feasible to produce sulphuric acid in conjunction with the treatment process, the sulphur can be usefully employed; but if this is not possible, then the sulphur contents not only become a dead loss, but tend to be a nuisance as well in the surrounding neighbourhood.The problem of avoiding this disadvantage and making economic use of the sulphur has had attention from the early days of scientific metallurgy, and in the past few years very special efforts have been made both to drive part of the sulphur as such from pyrites and recover it, and to replace the sulphur in the S02 by carbon, with the production of carbon dioxide and precipitation of the sulphur. So far economic success does not appear to have crowned these efforts. In the case of pyrites, of the two atoms of sulphur which go to make the FeS2, the first is very lightly held. Dissociation is effected by heat alone at a temperature which is given by Peters as 5160 C.Now, sulphur and hydrogen will unite or burn together, with the production of sulphuretted hydrogen. It occurred to the writer that, if hydrogen was passed over pyrites heated to the above temperature, this first atom would be snatched away by the hydrogen, and could possibly be economically recovered.The first step consisted of some simple laboratory experiments. From these it was found that this first atom was readily removed, and that the extraction was practically complete. Further, the reaction took place at a low temperature, a dull red heat being sufficient.

Jan 1, 1923

By Pengcheng Li, Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide could be utilized as a weak oxidant and a kind of coolant to oxidize elements, meanwhile, helping control the temperature during the converter vanadium extraction process. However, the optimum content of CO2 and the cooling effect of CO2 at low content have not been reported. In this study, experimental research based on the influence of different CO2 contents from 0% to 25% injected to the vanadium-containing hot metal was carried out, as well as contrast experiments of O2-N2 mixed blowing. The results indicated that the optimum content of CO2 was 15%. Under the optimum condition, the oxidation of [C] was the lowest and the oxidation rate of [V] was 96.9%, while the temperature was also lower than the O2-N2 mixed blowing. This paper provide a potential property for utilizing CO2 during the converter vanadium extraction process.

Jan 1, 2016

By Márcia Maria da Silva Monteiro Pereira

Tundish is the last reactor where significant metallurgical operations can still be done. Calcium aluminate slags are able to positively contribute to metallurgy considering oxide separation, protection against reoxidation and preclusion of resulphurisation. However, these are poor insulators. When using low melting point slags it is necessary to use another covering material. The deviation from saturation can be used as a measure of absorption capacity. By utilizing computerized construction of ternary and quaternary diagrams it is possible to compare different slags and to find proper slag compositions with reasonable capacity to dissolve inclusions. Objective of the present technical contribution is to evaluate tundish slag capacity to absorb inclusions, considering a particular tundish industrial slag and the changes in its chemical composition during continuous casting of steel. It was observed that slag composition changed during the continuous casting process; this variation is possibly related to interaction between the CaO-Al2O3 liquid slag and the rice hull ash layer which is used above it. Computational thermodynamics was used to determine activity of alumina dissolved in liquid slag; it was observed that the variation in slag composition did not change slag capacity to absorb inclusions, since precipitation of Al2O3 solid phases is not predicted.

Aug 17, 2017

By Ralph Arnold

THE American oil 'industry has reached the critical stage where the demand exceeds the supply with no hope of permanently bettering the situation through the development of new fields in the United States. Remedies may be sought along three lines: 1. Securing a foreign source of supply. 2. Curtailment of the use of oil and its derivatives. 3. Improvement in methods of recovery (including the recovery of shale oil), refining, and utilization. The oil companies with proper government support will push the acquiring of foreign territory; the price of oil and oil products will enforce a curtailment in use; it remains for the producers and refiners to brings about improvements and economy in recovery, transportation and refining; the general public must be instructed in utilization. The solution of the problem, therefore, rests largely in the hands of the technologists of the industry -the drillers, engineers, geologists, chemists, etc. Only through an exchange of the ideas of the individuals who are conducting the industry will its technology be advanced. , Among the agencies at work to bring about this result are the United States Bureau of Mines, the American Petroleum Institute, and the A. I. M. E. The Bureau of Mines has a trained staff of experts, maintains experiment stations and a field force of technologists, and issues many technical papers helpful to the industry. The Petroleum Institute is a clearing house for useful statistics and is now. organizing a research division under the able direction of Doctor Manning, but its principal field of activities is in the realm of co¬ordinating ?the financial and commercial activities of the` oil' companies.' It remains for the American Institute of Mining and Metallurgical Engineers to organize the individual technologists of the industry and provide them with means of exchanging and disseminating ideas through meetings and publications. It is the aim of the Petroleum Committee of the American Institute of Mining and Metallurgical Engineers to foster this exchange of ideas among oil men by enlarging the membership of the Institute among the field and office technical forces of the oil companies and thus arouse their interest in the vital problems of the oil business.

Jan 1, 1920

By E. J. Efsic, C. M. Wayman

The fcc to bcc y to a transformation in an Fe-24.5 at. pct Pt alloy was studied and found to be martensitic. Large martensite plates are formed in this alloy which are ideal for crystallographic studies; the Ms temperature is about -5°C. Ordering of the parent phase prior to transformation to martensite causes a pronounced lowering of the Ms temperature. For the first time in the case of alloys of iron, measurements of the habit plune, orientation relationship, and magnitude and direction of the shape stvain have been obtained on preselected martensite plates. It is shown that by measuring the initial and displaced (as a result of the shape strain) positions of three or more non-parallel fiducial scratches on one reference surfice the maguitude and direction of the shape strain and the state of distovtion at the parent-mavtensite interface can be determined with a reasonable degree of accuvacy. The agreement between the phenomenolog-cal crystallographic theory of martensitic transformations and the experimental results habit plune, orientation relationship, and nlagnitude and direction of the shape strain) is essentially perfect, and is thought to be the best reported to date for iron alloys. THE comparatively few investigations on binary Fe-Pt alloys have been concerned with magnetic properties, ordered phases, and the equilibrium diagram itself. Various investigations have shown that the equilibrium diagram is of the open y field type; in addition there is a peritectic transformation, a minimum melting point, and three ordered phases: Fe3Pt, FePt, and FePt3. The results of a number of investigators1-6 have shown that the temperature dependence of the y to a (and reverse) transformation in iron-rich alloys is reasonably well-established. The Fe3Pt phase was first noted by Kussman and Rittberg,7 and its existence was later confirmed by Franklin et al,8 Steijn and Donahoe,9 and Berkowitz et al.10 The FePt phase was reported by Isaac and amman' and later confirmed by a host of others.3,6,7,12,13 Kussman and Rittberg7 noted the existence of the superlattice FePt3. Prior to 1956, the 1 to a transformation in iron-rich Fe-Pt alloys was termed "irreversible". In 1957 Klokholm and Donahoe" termed this transformation martensitic, presumably because of its occurrence at temperatures well below those where diffusion normally takes place. This observation served as a point of departure for the present investigation, and in the very early stages of the work to be discussed it was readily verified that the y to a transformation in iron-rich Fe-Pt alloys is indeed martensitic. Quite large martensite plates exhibiting the well-known surface tilt were observed. These plates are ideal in the sense that the boundaries between the parent and product phases were usually very straight. It thus appeared that Fe-Pt martensites would be ideal for crystallographic studies, and this was the purpose of the present investigation. Details of the crystallography of martensitic transformations (particularly for iron alloys) and the phe-nomenological crystallographic theories15-l7 have been discussed many times and thus will require very little elaboration here. The end result of these theories, given in matrix form, is

Jan 1, 1968

By J Player, R de Vries, J F. Carswell, R Hassell

"The feasibility of Dugald River mine was highly sensitive to mining and geotechnical design assumptions, particularly stope dilution and strike length. Following the start of initial mine development in 2012 the project was suspended in 2013 due to concerns over the complex ground conditions and resulting dilution, stope sizes and general mineability. A technical risk mitigation program was undertaken with a key aim to increase the level of confidence in predicting stope dilution.A stope sizing and dilution model was developed that provided a range of stope sizes based on geotechnical conditions and acceptable dilution. The original feasibility used a standard stope size of 25 m height by 25 m span. The new model was used as the foundation for the subsequent updated development plan for Dugald River that reduced much of the previous technical risk through greater confidence in the geotechnical and mining parameters.Several methods to predict stope hanging wall dilution and appropriate stope size have been used at Dugald River that relied on the modified stability graph method. Improvements to the method were identified as more rock mass and mining data became available through the completion of a trial stoping program, increased underground development and a large geotechnical core logging campaign. These improvements not only focused on the technical aspects of the model, but also on creating an easy to use and sustainable process that could be used at multiple stages of mine planning from life-of-mine (LOM) through to final stope design.Several of the main improvements are: understanding stope failure mechanisms and collecting only geological information that is most relevant detailed modelling restricted to the rock mass that could be expected to influence stope behaviour accounting for different stope failure mechanisms with the stability chart method assigning a geotechnical confidence factor to the data making it useful as a mine planning tool with integration into the mine planning process using performance of completed stopes to update and calibrate the model.The model provides recommended hydraulic radius and associated dilution estimates across the ore body. Providing the hydraulic radius allows planning engineers the option to consider single, double and triple lift stoping options suitable to mine scheduling. While the model has been calibrated for conditions at Dugald River the process used to create the model is not site specific and is applicable to other steeply dipping tabular orebodies.CITATION:Hassell, R, de Vries, R, Player, J and Carswell, J F, 2017. Improving the prediction of stope hanging wall dilution – a critical factor to the success of Dugald River, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By J Johansson, B Johansson

The mining industry needs to attract and recruit young talented people. An important task is, therefore, to create an attractive mining workplace that engages with, and motivates youngsters who are not particularly interested in working in the industry. This paper aims to illustrate a way forward for the mining industry to form healthy and safe workplaces honouring key components such as knowledge, skill, co-operation, continual development and acceptance of diversity. This is a way to create a vision of healthy and safe mining work. The mining industry must work towards zero vision; a future without accidents and hazardous environments. In this paper the authors discuss different aspects of an ‘attractive workplace’ and summarises lessons learnt in 26 statements dealing with safety, both physical and social work environments, and social responsibility. The authors hope these recommendations will provide some guidance for how attractive workplaces should be designed for future deep mining.The paper is based on lessons from two large European projects, a Swedish-Polish project: The Smart Mine of the Future; and a European Union project: Sustainable Intelligent Mining Systems (SIMS). One of the authors was the WP leader of health and safety in both projects.CITATION:Johansson, J and Johansson, B, 2017. Attractive workplaces in future underground mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 99–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By C. W. Owning

"The Bureau of Mines has repeatedly emphasized the necessity of completely ""rock-dusting all coal mines, except anthracite mines, in every part whether in damp or dry condition."" Every open accessible part of, the, mine without exception should be thoroughly rock-dusted, including parallel entries, air courses, trackless entries, crosscuts, and rooms to within at least 40 feet of every coal face. Very few mines have followed this recommendation and warning, with the result that there have been explosions not only in mines which have not used rock dust but also in so-called rock-dusted mines. Following a number of mine explosions it has been reported that the mine was rock-dusted,"" whereas it is probable that only some of the haulage roads had been given a hurried application of rock dust and in most instances not as much as 5 per cent of the mine was really rock-dusted. That is not rock-dusting.Some conscientious, well-meaning mining men have felt that rock-dusting of haulage roads would effectively stop an explosion; however, when shown, through widespread explosions in mines ""well rock-dusted"" according to the above method, that leaving large areas undusted, furnishes paths through which a violent explosion may travel, these mining men have realized the necessity of thorough rock-dusting and have adopted this explosion-prevention method.The Mather Collieries mine, Pickands, Mather and Co., operators, at Mather, Pa., was the first mine in Pennsylvania to receive, full credit for rock-dusting under the new 'stringent ruling of the Pennsylvania Compensation Rating Bureau, the provisions of which require that:"

Feb 1, 1931

By B. Boryczko, J. Norwisz, Jose Escobedo Bocardo, Z. Kolenda, A. Holda

"Classical thermodynamic analysis of any thermal and chemical process is usually based on the first law of thermodynamics. Such an approach is not sufficient when deeper understanding of the nature of each elementary process is required. The use of the first and second law of thermodynamics together is necessary to solve practical process more effectively. Enthalpy and exergy balances allow to enhance our understanding of thermal processes especially when cumulative consumption of energy and exergy is calculated. To ensure reliability of such an analysis the least squares method for adjustment of mass balances of principal chemical elements has been applied and described in detail. Numerical analysis has been carried out to compare two different processes of copper production – shaft furnace and flash smelting.IntroductionClassical thermodynamic analysis of any technological process is usually based on the First Law of Thermodynamics in the form of energy (enthalpy) balances. Such an approach is useful in engineering practice as it makes analysis easier in the global scale neglecting modeling of the elementary processes, allows calculation of the thermal efficiency and makes possible to control quality of the measurement results. Additionally, graphical presentation of the energy balance is simple in the form of Sankey diagram.In the case of aluminum electrolysis process, design of the new electrolyzer or its modernization is always based on the enthalpy balance.However, deeper thermodynamic analysis leads to the conclusion that such an approach is not sufficient. The First Law of Thermodynamics guarantees the exact equivalence of the various forms of energy (allowing all forms to be measured in the common unit such as joules) but it does not guarantee interconversibility. Thermal energy (heat) is in a peculiar and unique position, for whereas all other forms can be completely converted into thermal energy, the reverse process id impossible, only a portion of the heat can be converted into mechanical energy. Explanation comes from application of exergy balances. As we know exergy expresses the amount of mechanical work necessary to produce a material in its specified state from components common in the natural environment, in a reversible way, heat being exchanged only with environment [1]. Consumption of exergy connected with the fabrication of some considered product appears not only in the plant manufacturing the product, but also in all plants delivering raw materials for the final production process"

Jan 1, 2008

By M. Javier

"Mining is the main activity that supports civilization. Actual mining presents contradictory concept to the health of the planet. Its business model is linear, fragmented and characterized by inefficiencies in the utilization of water, energy and mineral resources which generate waste and pollution. Before mining begins, it is critical to determine the vulnerability of the ecosystem and after mining, it is critical to determine the depletion of nature. Attending to these vital matters will require quantifying and measuring them. The purpose of this study is to provide and establish the metric to assess the performance and manage a sustainable future for our existence and that of our planet. This index is defined to measure and control Nature Friendly Sustainability (NFS) based on understanding nature. This index will determine the condition of nature constructed on the measurement of physical, chemical and biological equilibrium. Proposing a new mindset for mining design to satisfy nature’s needs would be to offer the same opportunities to future generations. Hence, sustainability is synonymous with equilibrium under a limited ecosystem. Nature is interconnected. Finally, this index of NFS is readable, standardized and relevant to keep nature’s needs in equilibrium. Establishing and NFS index is the next metric for humanity. INTRODUCTION There are a multitude of definitions of what sustainability is. Most of them are defined in terms of the corporate entity from which they emanate. The classical definition of management states that, “if we do not measure it, we cannot manage it.” Management of ecosystems is the definition of sustainability. Indicators of quantity and quality of sustainability are vital in order to create a metric for sustainability. These indicators will measure the depletion and degradation of nature as they occur through human intervention. The first step is to create a metric of sustainability to simplify its definition. The definition of sustainability is based on whether or not you consider nature to be finite or infinite, which is described in Nature Friendly Sustainability (NFS) [1]. The definition of NFS applies to any anthropogenic activity with an understanding of the equivalent activity in nature. That is to say, human activity with nature requires balance and equilibrium in order to be sustainable. The importance of this equilibrium is quantified in a set of metrics in order to establish measurement and acknowledge indicators for our dependence on nature. Sustainability is synonymous with equilibrium in any ecosystem that is limited and fragile. In the graph is the explanation of sustainability definition. See Graph 1"

Jan 1, 2017

By John D. Hanks

INTRODUCTION Chevron's Uranium Mill is located near Panna Maria, Texas; 70 miles southeast of San Antonio. Designed by Kaiser Engineering, the Mill will process a nominal 2500 dry T.P.D. of uranium bearing ore containing 15% uncombined moisture. Earl Torgerson, San Mateo, California, is the consulting metallurgist on process design. Feed to the plant consists of a mixture of high, medium and low grade sandy day ore; the average grade of the ore will be 0.7% throughout the life of the project. The ore is delivered to the mill via truck and stored by type in individual piles on a flat storage area. The ore is fed by conveyor to a semi-autogenous grinding mill. The SAG mill discharge slurry is pumped either to a storage tank or to the first of five mechanically agitated leach tanks where both H2SO and NaC103 are added. Following leaching, the slurry is mixed with thickener No. 2 overflow before being pumped to a six-thickener, countercurrent decantation circuit where the solution containing uranium is separated from the leach residue. The residue is washed essentially free of solubilized U308 values at the sixth thickener and discharged to an adjacent tailings pond. The first thickener overflow, containing approximately 0.4 grams U308 per liter, is filtered for clarification and sent to the liquid ion exchange (solvent extraction) section. The pregnant aqueous solution is mixed with organic solvent containing amine on which the complex uranyl sulfate ions are absorbed. The immiscible aqueous and organic solutions are mixed and separated in each of the four stages of solvent extraction. The final pregnant organic is directed to a stripping section. A strip solution containing (NH4)2S04 (ammonium sulfate) and NH4C1 (ammonium chloride) is contacted and separated from the organic in each of the four mixer-settler units. The strip solution is mixed with NH3 and the uranium precipitates along with trace amounts of sulfate, chloride, and ammonia. After washing in a thickener, the uranium precipitate or yellowcake is centrifuged and dried in a multiple hearth roaster. Overflow from the yellowcake thickener is recycled back to the stripping section of the solvent extraction circuit. The dried yellowcake concentrate contains more than 98% U308; diluents include H20, ammonia, chloride, etc.. Impurity concentratons in the product are sufficiently low, after drying, to permit direct shipment to refinement installations. ORE RECEIVING Ore from one or more mines will be stored on a pad adjacent to the uranium processing mill. Ore stored in the area may total 200,000 tons or more, which is equivalent to over a two month treatment reserve for the mill. In addition to providing surge capacity, the proposed storage facility permits natural oxidation of the ore and affords an area which, in turn, improve plant U308 recovery and reduces consumption of oxidizing reagents. The uranium bearing ore is segregated at the storage area into several distinct types. One group can be identified by its sandy, clay-like matrix and will be distinguished by its U308 concentration of high, medium, or low. Other ores contain substantial quantities of carbonaceous shale, typical of ore in the area. Feed is recovered from any one or combination of piles, in accordance with operating requirements and recovery factors. The run-of-mine ore, at 15% moisture, is transferred to a stationary, 24-inch by 24-inch grizzly. Undersize material falls into a 280-ton surge hopper located below grade, while oversize material is removed for preliminary size reduction. A sump-pump is located at the reclaim hopper to recover excess mositure and ore spillage for processing. Plant feed is continuously drawn from beneath the hopper at an average rate of 120 tons per hour by means of an apron feeder. The hopper is equipped with a low level safety system to protect the apron feeder assemble. The ore is transferred to a belt conveyor, elevated and discharged into a semi-autogeneous grinding (SAG) mill. Water addition at the discharge point is automatically controlled by a feed rate, moisture analyzer system located on the belt conveyor. GRINDING Minus 24-inch ore, at a rate of 120 mosit tons per hour and cyclone underflow at a rate of 137 moist tons per hour are combined with a controlled 186 gallons per minute fresh, warm plant process water. The mixture, at an average 68% solids, is fed to the SAG mill. The viscous mass is subjected to grinding at a temperature moderately above ambient resulting from use of the 140ºF well water. The 16.5'x5.0' Marcy Mill is driven by a 500 H.P. A.C. Motor. The mill will rotate at 73.4% of critical speed or 14.06 R.P.M. Eight percent of the mill's volume will be occupied by steel grinding balls; 22% by pulp. The mill is designed to rotate in either direction, in order to obtain maximum lifter and liner life. The SAG mill is equipped with a trommel having ½ -inch slots for removal of oversize material at its discharge and the large or oversize material is collected and either recirculated periodically or discarded. The undersize slurry is diluted to 64% solids with the addition of hot well water or mine water to the mill discharge sump. The flow is automatically controlled utilizing data from a gamma density meter. The slurry from the mill discharge sump is pumped to hydrocyclones to classify the particles. Underflow from the cyclones, at 80% + 28 mesh, is recycled to

Jan 1, 1979

By S. R. Goodman, Hsun Hu, R. S. Cline

The quenching technique has been used to study phase relations in the composition area 2FeO.SiO2-FeO-SiO2-MnO.Si02-ZMnO.SiO2 of the system iron oxide-manganese oxide-silica under strongly reducing conditions such as exist in a gas mixture consisting of equul parts of carbon dioxide and hydrogen. Liquidus and solidus temperatures of most mixtures in the composition area studied are in the range of 1173° to 1345°C. EQUILIBRIUM relations existing among the oxides of iron, manganese, and silicon are of particular interest in two areas of steelmaking: slags and ingot inclusions. Mixtures of these oxides represent about 90 pct of the slag in the acid steelmaking process, and so dominate the chemistry of the whole refining process. These constituents also play an important role in the early slags existing at the time of the "lime boil" in the basic open hearth process. If these slags are liquid, they "wet" the lumps of lime rising from the bottom of the bath, and react with them. A liquid slag rich in CaO is then formed at the very beginning of the refining. Because the temperature is still low, all conditions for a good dephosphoriza-tion are fulfilled at this stage of the operation. Metal deoxidized with ferromanganese or silico-manganese is likely to contain, as inclusions, phases made up from among the oxides of iron, manganese, and silicon. A knowledge of stability relations existing among the phases present in this system, therefore, enables one to predict the hardness of the inclusions encountered. Moreover, because the shape of the inclusions in steel has a profound influence on the physical properties of the metal, it is important to establish whether or not the oxidic material is present as liquid or crystalline phases during heating and rolling of the steel (-1150 to 1350°C). A knowledge of melting relations in synthetic mixtures of iron oxide, manganese oxide, and silica will give a clue to these problems. Methods for determining such relations and the results obtained are described iln this paper. I) PREVIOUS WORK A number cf previous studies have dealt with the three "binary"* systems bounding the system iron oxide-mangar,.ese oxide-silica. The system iron oxide-silica was studied by Bowen and shairerl in 1932. Their data were obtained by equilibration of mixtures in contact with metallic iron. Phase relations for the system iron oxide-silica ill atmospheres of different oxygen pressures car1 be derived from data on the system FeO-Fe2O3-SiO2 as determined by Muan.2 The diagram shown iri Fig. l is a section of this system in an atmosphere of CO2 and H2 in ratio 1:l. The system manganese oxide-silica has also been the subject of several investigations. Most of the early studies suffered from a lack of proper control of the atmosphere under which the equilibrations were carried mt. Phase diagrams for the system at two well defined levels of oxygen pressures have been determined recently. Glasser3 determined stability relations in an atmosphere consisting of carbon dioxide and hydrogen in ratio 5:1, diagram Fig. 2, and Muan4 studied phase relations in the system in air.

Jan 1, 1962

By E. H. Rose

IN a year of sober reflection and stocktaking after the mineral-squandering spree of World War II, the role that beneficiation of low-grade must henceforth play in American mineral industry has become unmistakable. From the volume of research and development progress in mineral engineering during 1946, mineral dressers evidently have ample resoluteness to meet the challenge. Perhaps ,the most conspicuous trend of the year was the renascence of interest in gravity concentrating methods and more serious effort than ever before to make them effective in finer size ranges down to 200 mesh. This has been forced by the problem in iron ores where the low value of the product will not support a high flotation reagent cost, however good flotation pilot plant results may have been and however well the acute problem of variable feed may be met. The race is on between rabbit flotation and tortoise gravity methods and a surprising amount of betting money is being laid on the tortoise which already is showing previously unsuspected talent for speed. Mostly, however, a wait-and-see attitude prevails during the present preliminary heats. As evidence of the latter, two magnetic plants are now on the boards for magnetic taconites on the eastern Mesabi to establish a reprieve against the time when nonmagnetic taconites must be addressed. Incidentally, these operations will force the blast-furnace issue on preparation of fine material since a minus-100-mesh grind is contemplated.

Jan 1, 1947

By Howard Willey

Mining operations of the Charcas unit at present are limited to the Tiro General mine at Charcas, in the State of san Luis Potosi, Mexico. The Tiro General mine was first operated during the Spanish occupation of Mexico for rich silver ores in an oxidized zone along the outcrop of the principal vein. In depth the ore is a complex sulfide with widely varying proportions of sphalerite, argentiferous galena and chalcopyrite ; and until recent years, it was economically impossible to carry on mining otherwise than irregularly in sections of the veins richest in galena and chalcopyrite. The advent of selective flotation brought the orebody as a whole within the field of economic interest, and a flotation mill of 650 metric tons daily capacity was constructed in the year 1925. The mining of partly worked-out sections of the mine, as well as the very heavy ground in most of the stopes opened in virgin ore, presented an unusually difficult problem. This paper describes the so-called "filled top slice" stoping method finally adopted as the standard system. Physical and Geological Conditions The principal orebody of the mine is an oreshoot about 1400 ft ng in a fissure vein striking about east and west and with an average lip of 70" to the north. The footwall of the orebody is fairly cleancu and regular both longitudinally and vertically and generally shows a dell-marked post-mineral slip. The footwall rock varies from a fairly strong limestone to a broken, metamorphosed limestone which requires heavy timbering. In some sections it is an altered, crumbly porphyry, which swells badly and necessitates frequent renewal of drift and raise tirnber. The hanging wall is irregular and frequently an assay wall. The stopina width ranges from a few feet up to more than 90 ft.; it averages about 30 ft. For the most part the hanging-wall rock is a shattered and altered monzonite porphyry, nearly aways requiring heavy timbering. The orebody is greatly fractured by post-mineral movement, which usually followed the footwall and left it as a smooth surface frequently covered with a slippery clay gouge. Two well marked transverse faults

Jan 1, 1931

By D. M. Ramsey

HIGH-INTENSITY magnetic separation as now practised in the commercial treatment of a large variety of industrial minerals is a com-paratively recent development, having had its practical beginning about ten years ago when it became necessary to devise more effective methods for the purification of the electric furnace abrasives and refractories-silicon carbide and fused aluminium oxide. The fundamentals of magnetic separation are, of course, very well under-stood; bur while very, very old in principle, the process has, in recent years, been developed to a point of far greater usefulness than heretofore. In fact, until the development of the high-intensity process,. magnetic separation was limited largely to the removal of tramp iron? with magnetic pulleys and the removal of the very highly magnetic portions of industrial minerals by means of horizontal conveyor-belt-type separators. All magnetic separation processes depend for their success on the fact that various materials are kinetically influenced to a greater or lesser degree by the force that we speak of as 'magnetism'. We have now come to regard 'magnetic separation' and 'high-intensity magnetic separation' as two different and distinct methods. However, both depend upon the reaction of a particle when placed in a magnetic field. The common types of magnetic separators quite generally operate on the principle that a magnetic particle can be lifted by a powerful magnetic force from a stream of material moving on a belt or other type of conveyor. The application of the force removing magnetic material by this scheme is directly opposed to the force of gravity and is, therefore, limited to sub-stances of a relatively high order of magnetic susceptibility, such as metallic iron and magnetite. Until a few years ago, one very important principle was almost entirely overlooked. Practically every substance is susceptible to some extent, at least, to magnetic attraction, and by the application of a magnetic force great enough, and properly applied, separations of materials heretofore considered 'non-magnetic' can be accomplished.

Jan 1, 1937

By Yuan Zeping

This paper describes the distribution and removal of the main impurities in the pyrometallurgical process ?at the Guixi Smelter. The paper discusses in detail our converting schedule?of3S-SB and injecting deeply a mixture ofNa2CO) and CaO flux into the converters to enhance impurity removal.

Jan 1, 1998

By Zhangm Zeqiang, Manman Lu, Hanquan Zhang, Hong Yu, Jintao Fu

"Pelletizing is an important technique in the ironmaking industry. Artificial and natural magnetites are materials that are widely utilized in the iron ore pelletizing process. In this work, the pelletizing characteristics of these two types of magnetite have been investigated in detail. The obtained results shown that in contrast to natural magnetite, the artificial magnetite concentrate exhibits stronger hydrophilicity, lower electronegativity, larger specific surface area, and rougher surface. In addition, the green pellets produced from the artificial magnetite concentrate are characterized by a higher compressive strength as compared to that of the pellets obtained from the natural magnetite concentrate. However, the shock temperature of the artificial magnetite pellets around 255 C is significantly lower than the threshold specified by the industry. The balling characteristics of the material obtained by mixing 20% of the artificial magnetite concentrate with 80% of the natural magnetite concentrate are considerably improved with respect to those of the individual components.INTRODUCTION Pelletization is an essential process of the ironmaking industry in China. Since the pellets produced from iron ore exhibit high mechanical strength, good particle granularity, and uniform shapes, pelletizing high-grade iron ores with good metallurgical reducibility can lower the coke ratio, improve their technico-economic index, and reduce the cost of processing pig iron in blast furnaces[1, 2]. Presently, high-grade magnetite is a material utilized for pelletizing various iron ores across the globe. However, its natural deposits have been depleting rapidly in recent years; as a result[3], China’s dependence on the foreign high-grade iron ores exceeded 70% in 2009 and reached the level of 87% in 2016. Hence, possible methods for the efficient cultivation of limonite, siderite, hematite, and other refractory minerals that correspond to low-grade, finely sized, inhomogeneous, and scattered iron ores have attracted significant attention [4, 5]. In particular, magnetization reduction roasting and magnetic separation techniques, which are widely utilized for obtaining high-grade artificial magnetite, represent effective ways of processing iron ores that can alleviate the scarcity of natural magnetite resources [6, 7]. The artificial magnetite produced by magnetization reduction roasting exhibits different characteristics as compared with those of natural magnetite (including the degree of hydrophilicity, surface potential, specific surface area, and other surface physicochemical properties[8-11], which significantly affect its pelletizing behavior. In this work, the surface characteristics of artificial and natural magnetites are investigated in detail, and their effect on their pelletizing properties (such as green ball strength, heat stability, and pelletization rate) are examined."

Jan 1, 2018