Search Documents

By Henning E. Soderberg

Yesterday, air pollution was somebody else's problem -- today, it is everybody's problem. The coal industry with thermal coal drying, is aware of their problem and the necessity of doing an acceptable job; however, there is much to be said as to how good a job is required and what performance limits should be set up. American Air Filter Company has been one of the pioneers in the solution of the thermal coal dryer dust problems, Because of high moisture content, products of combustion and occasional temperature surges, only wet collection has been considered as the practical approach. Our first installation goes back some 12 years with a total to date of 29 Individual wet collectors, each, fabricated of suitable corrosion-resistant material, at 14 operating plants. To eliminate a potential air pollution problem, a performance requirement of not more than approximately one-quarter (1/4) grains per cubic foot in the dust collector discharge was used. In nearly all installations, operating performance surpassed requirements, but discharge stacks were not entirely free of discoloration. However, plant nuisance and air pollution complaints were eliminated. This satisfactory performance was accomplished by medium priced wet dust collectors operating at a 4-6" W.G. pressure drop with cater drain requirements of about 1 gallon of drain water per 1000 cubic feet of air exhausted.

Jan 1, 1962

By M. Somppi, D. Weirmeir, Z. Yamak

"Milling operations commonly employ activated carbon to capture complexed gold from lixiviants in leaching processes. As the carbon moves through pipes, pumps, vessels, kilns and other processes in the gold leaching circuit, this consumable may experience losses by various mechanisms like attrition, breakage, and rupturing. Whenever possible, capturing the fine gold-bearing carbon portion of this stream could provide value to milling operations at low capital cost and manageable financial risk. Identifying, testing, and validating the successful payback of a low-tech flocculant system is described. However, the work more closely explores a Monte Carlo risk-based methodology for understanding the potential payback of this project at various confidence levels – an approach that many improvement projects can follow where some level of uncertainty exists.INTRODUCTION Gold milling operations commonly employ activated carbon to adsorb gold from solutions. Normal handling causes the carbon particles from this material to abrade, break, rupture to a size that becomes too small for further use in the process. Operations often concentrate on capturing the fine particles because gold is associated with the carbon and this metal content can be a valuable revenue stream for toll processing. However, the small particle sizes become difficult to separate from the process and can ultimately leave the facility in the waste stream. Hence, operations often place a great deal of care in capturing as much fine carbon as possible by a variety of methods including using screens, settling tanks, and chemical methods. Retrofitting a circuit to capture more carbon fines is common but can expose the operation to financial risk. Approaching this potential improvement by leveraging a Monte Carlo methodology can be effective in understanding the risk and the associated payback of a project at various confidence levels. This method provides a strong framework for capital go-no-go decisions and the structure to validate the potential project success before implementation."

Jan 1, 2019

By G. Clarkson, M. Hitch, R. Clarkson

"A novel reagent-free method of extracting gold from gravity middling concentrates in the Yukon placer fields is presented in this paper. This method exploits the malleability of gold by submitting concentrates to grinding in a rod mill. Brittle waste minerals are effectively reduced, whereas malleable gold particles are flattened and are then extracted by classification through sieves. Recoveries in the field using a laboratory-sized rod mill regularly exceeded 90%, whereas correlation laboratory tests indicated recovery to be most sensitive to the mill charge size. This method has broad potential, including application to the gravity circuits of large hard-rock processing circuits.RÉSUMÉ Cet article présente une nouvelle méthode sans agents réactifs d’extraction de l’or dans les concentrés gravimétriques mixtes que l’on trouve dans les districts placériens du Yukon. Cette méthode exploite la malléabilité de l’or en broyant des concentrés dans un broyeur à barres. Les déchets miniers cassants sont bien réduits, alors que les particules d’or malléables sont écrasées puis extraites par classification au travers de cribles. Si les récupérations sur le site à l’aide d’un broyeur à barres de laboratoire excèdent 90 %, les essais de concordance en laboratoire indiquent que la récupération est très sensible à la taille de la charge du broyeur. Cette méthode présente un grand potentiel, notamment une application possible aux circuits gravimétriques des grands circuits de traitement des roches dures.INTRODUCTIONExploiting the high density of gold to separate it from waste materials is the oldest known mineral processing technique. This basic technique is still widely used in gravity concentration circuits today; however, gravity processing invariably results in high-value middlings, especially in the Yukon placer gold fields. In addition to having a uniquely high density, gold is also the most malleable metal. This unique malleability can be exploited to extract gold from otherwise inaccessible gravity middlings.The Yukon placer gold industry has been continuously ongoing since the 1860s, and today produces approximately 60,000 oz t (1.87 million grams) of crude gold annually, most of which is from the Klondike region near Dawson City (Van Loon & Bond, 2014). It is important to note that Yukon placer miners do not use any chemical extraction methods; rather, gravity upgrading methods are the sole processing techniques used. Placer deposits are typically coarse, well liberated, and naturally gravity concentrated and recoverable, thus making more expensive chemical extraction unnecessary (Mitchell, Evans, & Styles, 1997). Furthermore, a strict permitting regime, environmental concerns, lack of expertise, and fear of repercussions from regulators prevent miners from attempting more advanced processing methods, such as flotation or cyanidation. Even simple chemical extractions like mercury amalgamation have not been implemented for decades, with one observer noting that, as many as 30 years ago, “the art of mercury for amalgamating appear[ed] to be dying [in the Yukon]” (Osler, 1983)."

Jan 1, 2017

By A Gibbs

The mining sector has been a leader in investing in safety improvement initiatives, yet relatively few mining organisations can accurately track the positive effects of these initiatives or identify areas that may require more attention. The consequences of not taking safety seriously are severe, and unfortunately injuries and fatalities are continuing to occur across the mining sector (Brady, 2019). There is a tendency to turn to lag indicators such as All Injury Frequency Rate (AIFR), Total Recordable Injury Frequency Rate (TRIFR), and Lost Time Injury Frequency Rate (LTIFR) to track these outcomes. As outlined below these approaches are inherently flawed and a renewed focus is needed on indicators within the control of leaders, indicators that have high predictive validity for future events and data that is used in a way to enable learning and change.

May 5, 2022

By D. Marcus

A methodology was developed wherein. the increase in compressive strength, mineralogical changes and pore water composition were all studied simultaneously as a function, of moisturized spent shale curing time. From these results the relationship between the nature of cementation process and the composition of pore water was established. Heavy metals were entrapped in the cementing constituents and the pore water became mainly a solution of alkaline sulfates. While the specific data are applicable only to the material studied, the methodology and general conclusions are useful for evaluating the environmental factors in spent shale disposal and expected leachates composition.

Jan 1, 1984

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By N. A. Frazier

The technology for using limestone or lime to scrub SO2 from power-plant flue gas has significant implications to the limestone industry. A brief status report on these processes will be made, possible process requirements on the limestone properties will be reviewed, and projections on the buildup of demand with respect to time will be reviewed. Disposal problems inherent with the use of these throwaway processes will also be summarized. Given a viable technology, relations among (1) distance of power plants from low- and high-sulfur coal and limestone deposits, (2) modes of handling and transporting immense tonnages of bulk material-coal and/or limestone, and (3) regional air-quality standards are some of the factors which will ultimately determine the demand for limestone. A discussion of these factors will be presented, with the intent of identifying geographic regions where significant increases in production can reasonably be expected.

Jan 1, 1974

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

"The standard method of separation using flotation is compromised in terms of kinetics and efficiency, because of the generally slow separating differentials of fine bubbles and fine particle suspensions. A new flotation system has been developed that addresses these issues and imparts other benefits. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. Consequently the cell is designed only for the separation of the phases and not for bubble-particle contact. In the new system this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The observed result of these differential forces is the improvement of concentrate qualities by the reduction of the amount of misplaced material found in the froth. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.Prototypes of 0.65m, 1.7m and 2.2m cell diameter size have been constructed for hydrodynamic and industrial scale tests to assess the previously established computational methods for scale up of the process. The 1.7m cell has been installed and operated for cleaning of potash concentrates in Germany, at throughputs of 150 m3/hr, with extremely encouraging results. A 2.2m cell has been installed and operated in plant trials for superfine coal in South Africa. Results are presented that illustrate the effects of differential separations by comparison with conventional pneumatic and mechanical flotation techniques. Predictions of performance are provided in the contexts of the applications tested."

Jan 1, 2003

By Markus Papst, Denise Millier, Daniel Beckers, Axel Preusse

"At an open-pit lignite extraction mine in Germany, groundwater has to be pumped over a large area, which leads to subsidence at the surface. As long as the geology of the area of influence is homogeneous, the subsidence is uniform and has marginal influence on buildings.Since the geology of many regions is characterized by faults, there are different rates of subsidence along those faults, which can lead to considerable consequences. Those different rates of subsidence on both sides of a geological fault are associated with the structure of the geology and soil mechanical properties. Horizons with various thicknesses and types of soil are affected differently by the groundwater pumping because of the offset of the faults, and thus react dissimilarly to dewatering.The smaller the grain of the geological horizon, the stronger the chance of shrinking, which leads to a stronger effect at the surface; therefore, dewatering impacts on clayey soil are different to those on sand and gravel. Regions consisting of meadows with turf inclusions are endangered as well; compared to the surrounding geology, those areas react in an entirely different way to water removal, which leads to immense differences in subsidence.The differences in area and respective subsidence impacts, as well as if it is possible to localize those areas, is an issue which needs to be analyzed. Furthermore, detailed mapping can help in the development of future forecasts about those subsidence differences and can also help with monitoring geological faults. In the context of subsurface spatial planning, this mapping has to be kept under review medium- to long-term.INTRODUCTIONThe utilization of underground mining is of increasing significance and of high interest, both for the common good and for future generations. For decades, humanity has been extracting resources from the subsurface, and salt, coal, lignite and water - just to mention a few resources - have been extracted from underground (Sailer, 2013)."

Jan 1, 2016

By M. G. Pelipetz

High-pressure, high-temperature hydrogenation of coal has been known and practiced for many years. A full' understanding of the mechanism in this process by which coal is converted to oil and gas must rest on a critical interpretation of the manner in which external variables influence the rate and the course of the coal-hydrogenation reactions. Same Bureau of Mines studies on the effect of temperature, catalyst, and rank of coal on these reactions have been published. The effect of pressure was not studied in this earlier work, and the effect of reaction time was complicated by the interruption of long reaction periods in order to refill the autoclave with hydrogen. It is the purpose of this paper to present data from more recent autoclave experiments that extend the results of Storch, et al, on the kinetics of coal hydrogenation. These data must be explained by any comprehensive theory of coal hydrogenation; their detailed evaluation, however, will be deferred until a later publication.

Jan 1, 1949

Updraft sintering of lead concentrates was introduced at Port Pirie in 1955 and since that time a considerable amount of investigational work has been carried out in the laboratory and on the plant with the objective of improving both the understanding of the process and its practical application.From this work it is now possible to predict trends in design and operation, which should result in capital savings and increased efficiency of future updraught plants.INTRODUCTIONOver the last 70 years a remarkable advance has been made in the method of preparing lead concentrates for smelting in the Port Pide blast furnaces of The Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.). Beginning in 1889 with heap roasting, the process progressed to Ropp roasters and Huntington-Heberlein pots in various combinations, then to multiple small Dwight Lloyd (D.L.) downdraught machines. In 1940 two large 10 ft by 50 ft D.L. downdraught machines were installed, and finally in 1955 updraught sintering was ,introduced with the installation of the present 10 ft by 99 ft sinter machine.At the time this last machine was built it was the first unit of its type and thus, of necessity, an experimental machine. During the eight years it has been operating a considerable amount of investigational work on sintering has been carried out both on the plant and in the laboratory.It is now felt that sufficient information is on hand to predict at least tentatively, some of the future developments in lead sintering, whereby both the quality of the sinter and the rate of production may be improved. This will result in a considerable reduction in smelting costs.

Jan 1, 1964

By C. S. Spirakis, A. V. Heyl

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The modified basinal brines, containing partly oxidised sulphur species, scavenged metals from basement rocks and sediments and transported them through the host rock, which contained local concentrations of organic matter. Reacting in various ways with the mineralising solution as temperatures at the sites of mineralisation changed, organic matter caused the precipitation and dissolution of a variety of minerals in the ore zones; it was organic matter that caused all of these reactions to occur at the same sites. Thus all components of the mineralising fluid - salt, water, heat, sulphur and metals - were obtained within the ore district. The siting of the mineral districts was related to the locations of faults through U- and Th-enriched granites beneath sediments containing basinal brines, and the locations of ore deposits within the districts were controlled by local concentrations of organic matter

Apr 1, 1995

By T. Majcherczyk

Shaft lining reinforcing analysis of two shafts under construction has been presented in this study. The first shaft was driven from the surface, while the second was deepened. Mining and geological conditions have been studied with respect to the lining capacity. The improvement of shaft stability comprised two elements, i.e. reinforcement of the shaft lining capacity and improvement of the strength properties of the rock mass. In both tested cases, the particular hazard was connected with non uniform loadings of the lining, which could generate shearing stresses within lining structure. Thus such elements as armored concrete with high strength properties, bolting and injection sealing of the rock mass, and the use of special ring reinforcing the shaft lining have been used in order to reinforce the shaft-rock mass system. Practical conclusions related with new technological solutions, allowing the rock mass and shaft lining reinforcement, have been included for the present study. Practical conclusions related with new technological solutions, allowing for rock mass and shaft lining reinforcement, have been also included to the present study.

Aug 1, 2013

By G. Demi

Chromium ore exploitation has commenced in 1948 in Albania and there are produced about 24.3 million tons up to the end of 2006. Last years the prices and need were increased notably. Main export of chromium ores and concentrates was accomplished respectively 114 500 ton and 13 000 ton in People Republic of China during 2006 year. Location, status, reserves and grade of chromium deposits of Albania are presented in the paper. Chromium ore enrichment is related with their composition and Cr2O3 content, as well as with market requests. Actually, high grade chromium ores with Cr2O3 content over 38% ~ 40% are directly exported or treated in metallurgy, but last time have been exported and chromium ores with 28% ~ 30% Cr2O3 content for the reason that dressing plants can not be operated for investment lack. High grade chromium ores have been treated in heavy media separation plant before 1990. It is presented flow sheet, figures and necessity to put in operation HMS plant in the paper. Actually, low grade chromium ores with content 16% ~ 20% Cr2O3 are not enriched for the lack of investments, but before 1990 they have been concentrated in dressing plants producing chromium concentrates grade 48% ~ 50% Cr2O3. In the paper are shown technological schemes and industrial figures during more than 20 years operation and possibilities to reconstruct these mineral processing plants. Only chromium mineral processing plant of Bulqiza is in operation using as raw material its old existing tailings. The flow sheet and figures show that are possibilities to increase recovery and grade of concentrate in the plant. Separation and concentration of slimes in suitable equipment gives visible improvement of Cr2O3 recovery. Several tests have been carried out with flotation and magnetic separation methods for enrichment of low grade chromium ores. Flow sheet and figures of mineral processing ores content olivine as gangue mineral are interesting, because combination of gravimetric with magnetic methods is necessary in this case. In the paper are presented the tests and good results of low chromium ore pre concentration. Metallurgical treatment of chromium ores to produce Ferro chrome, as well as technological process, figures, consume of electrical power and materials in Elbasani and Burreli furnaces are shown and necessary investments to treat in metallurgy all produced chromium ores in Albania are considered.

Jan 1, 2014

By R P. Varden

This paper looks at the design of the Bentayga raisebore with subsequent back analysis using a LiDAR survey. A search for LiDAR raisebore assessment publications shows little work has been done on this subject. The paper examines the empirical design and RS2 modelling assessment with the bored condition. The high resolution of the LiDAR enabled mapping of weak structures that were located on the geotechnical investigation hole the orientations of which could not be determined. In addition, the scan showed were water ingress was occurring, potential stress overbreak and structural controls on stability. The LiDAR results were able to confirm no additional support work such as a shotcrete liner is necessary. The LiDAR results have been analysed in one metre increments as volume of overbreak against the empirical stability criteria (McCracken & Stacey 1989). The future use of LiDAR mapping over a range of rock mass conditions will provide quantification of the established empirical assessment improving its reliability. It is also a useful and accurate tool to monitor long term stability of a raisebore due to stress change or ore pass due to wear.

Mar 15, 2021

By MAX VOS

Lithium is the lightest and electrochemically most reactive of all metals. Renewed interest in lithium coincides with research in lithium batteries and power generation by atomic fusion. Ontario lithium resources are contained in spodumene pegmatites that can form where medium- to high-grade metamorphic volcanic-sedimentary formations are intruded by pegmatite and porphyritic granitic rocks. Spodumene pegmatites occur in at least twelve locales throughout northern Ontario, all of which are in the Superior Province of the Precambrian Shield. Tantalum, cesium, rubidium, beryllium, niobium and tin also were noted with lithium in spodumene pegmatites. Considerable potential remains for discovery of additional lithium and rare-element pegmatites in northern Ontario.

Jan 1, 1984

By Nelson de Freitas Costa

Em um ensaio de impacto Charpy convencional, não é comum mensurar a energia consumida nas etapas de fratura, geralmente se obtém apenas a porção de fratura dúctil. Esse trabalho tem como objetivo apresentar a proporção do consumo de energia das diferentes etapas de fratura e relacionar com a área de superfície de fratura do corpo de prova. Ainda, desenvolve discussão dos fenômenos envolvidos, utilizando a teoria já conhecida. Para a obtenção dos dados foi realizado ensaio de Charpy instrumentado em 50 corpos de prova de 9 lotes diferentes. As amostras foram retiradas a 1/3 do raio da seção redonda de barras laminadas a quente temperadas e revenidas. As amostras foram preparadas conforme amostra do tipo A, definido na ASTM E23. O ensaio foi conduzido a -20°C, obedecendo a norma ASTM E2298. Os resultados mostraram que aproximadamente 80% da energia consumida na fratura é consumida na etapa de fratura dúctil, sendo que 88% dessa energia é consumida na região de início de fratura. Essa região, porém, não representa maior área na superfície de fratura, devido a diferença de trabalho para deformação nas etapas de nucleação de trinca e propagação instável de trinca.

Oct 30, 2017

By D. Harrington

TheRe has been, during the past year, a wealth of report data and discussion relating directly or indirectly to various phases of ventilation of metal mines, and many of the data are from foreign sources. The phase of the subject most generously accorded the attention of the technical press is that of cooling mine air, with much less attention to other fairly intimately associated features such as fan performance, friction factors, fires, mine gases, mine lighting, health of miners, and ventilation standards. Cooling Mine Air South Africa, with its very deep mining on the Rand and with fairly high working temperatures, 'contributes the most definite data on the subject of cooling mine air, and undoubtedly the most interesting issued are those from a paper by J. H. Dobson,' in which he gives a comprehensive review of the subject as gleaned largely by analyzing the data in three papers.2 Dr. Dobson's summation is decidedly interesting. In general it is recognized that the introducing into the mine and circulating to the working places of large volumes of pure air is the most effective method of giving deep, hot metal-mine workings reasonably efficient working conditions. A tabulation as to the cost of securing various amounts of cooling by circulating various volumes, from 230,000 to 760,000 cu. ft. per min., indicates that there are cost limits beyond which increase of quantity of air in circulation is impracticable, as the annual cost of circulating 230,000 cu. ft. of air per min. in a certain mine at a depth of

Jan 1, 1928

By C. J. Kirkland

For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water that separates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peaceable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1991

By Bruce T. Stanley

Though most porphyry-molybdenum deposits lend themselves to various reserve estimating techniques, still there must exist the constant effort to not merely obtain an estimate but rather to obtain the best estimate. To answer the challenge of a complete ore reserve estimation, one must attack the problem with the purpose of obtaining the results closest to reality. What we wish to determine is simple: metric tons (short tons), grade, and kilograms (pounds) of molybdenum contained. In order to effectively accomplish this task, further consideration must be given to the ease of using the information obtained and its inherent reliability. The only known method for ore reserve estimation that supplies the needed results along with its distribution and a measure of confidence provided by sound mathematical backup is geostatistics. The following review is an example of geostatistical application of an ore reserve estimate at the AMAX Henderson mine demonstrating technique, viability, and usefulness of results.

Jan 1, 1979