Search Documents

By I Coombes, M Trim, Y Sun, M McRae, A Spiegl, H Lagger, A Amon, P Barraclough, M Villeneuve

The Brisbane Airport Link Project (AirportlinkM7) includes the design and construction of more than 12.5 km of tunnels, with the Kedron interchange including four ramp tunnels that intersect with mainline tunnels and result in caverns with spans of up to 26 m. These caverns are in highly variable ground conditions with less than 35 m of cover underlying residential neighbourhoods and commercial properties. The Kedron caverns were constructed using the sequential excavation method (SEM). Owing to complex geometry and excavation sequence, the caverns were designed based on numerical modelling methods, including both two- and three-dimensional models. These numerical methods were used to develop a suite of support types with excavation sequences for the expected range of ground conditions. A combination of methods that included in-tunnel monitoring (convergence monitoring and extensometers), probe holes, endoscope probes, face mapping and ground settlement measurements were used to verify performance of the tunnel support systems and to select and refine the appropriate support system for each section of the caverns. The construction monitoring data indicated that numerical modelling can provide a good basis for predicting the performance of large-span underground openings in highly variable ground conditions. This paper presents a comparison of the performance of the caverns predicted by state-of-the-art numerical models and the actual measured performance.CITATION:McRae, M, Villeneuve, M, Trim, M, Sun, Y, Barraclough, P, Spiegl, A, Amon, A, Lagger, H and Coombes, I, 2014. Brisbane Airport Link Project – design and construction of the 26 m span Kedron Caverns: comparing monitoring data with the design, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Y Gu, R Fandrich

Traditionally, characterisation of the mineralogy and textures of ore and rock samples were based on observations of hand specimens and thin sections using an optical microscope. The extent of the data collection was limited by the available tools and thus variations in mineralogy and texture were generally not described by quantitative data. These qualitative to semi-quantitative approaches, even though well established over the years, resulted in variable observations and data sets. The data were unlikely to be representative of a sample and limited statistical validity meant the results could not be reliably used in modern digital mining design and planning. With recently developed SEM based quantitative mineralogy tools and the corresponding methodologies, ore textures can be quantified and compared numerically. The numerical data can not only enhance the understanding of an orebody in geological terms, but can also be used in the creation of metallurgical models for mine and mineral processing design and simulation. These capabilities provide valuable inputs to risk assessment studies and the evaluation of mineral projects.

Jan 1, 2007

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators 1-5 have noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilities6 and by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported' to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of this portion is shown in Table I and an approximate mineralogical analysis is shown in Table II. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of -6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1952

By T. P. Chen, F. W. Bowdish

Studies made with a captive bubble apparatus on the sulfidization and collection by amyl xanthate of true chrysocolla specimens have defined the ranges of pH value and sulfide concentration which permit contact between the bubble and the mineral surface. Titanium compounds were the most effective of the materials found to activate the sulfidization of chrysocolla. With titanium activation, the contact angles and the ranges of pH value and sulfide wncentration giving bubble contact were all increased. Chrysocolla ores were concentrated by flotation. Chrysocolla ores occur at many localities in grade and quantity sufficient to make mining and millin feasible, but no satisfactory method of concentratio has been found. Although chrysocolla may be leached with acid, only those ores without acid-consuming gangue may be leached economically. Because of its potential importance, a study of the conditions nece sary for flotation of chrysocolla has been carried ou The literature contains a few references to flotation of chrysocolla. Two methods were developed by the U. S. Bureau of Mines.1,2 The first consisted of a fatty acid soap and a high xanthate as collectors of chrysocolla from a synthetic ore, while the second involved the use of hydrogen sulfide and xanthate. Ludt and DeWitt3 demonstrated the difference in adsorptive powers of chrysocolla and quartz for bas triphenyl methane dyes and suggested the use of butyl, hexyl or octyl-substituted malachite green as collector. Jackel4 emphasized the effects of combin tions of reagents such as Aerofloat 31, pine oil, and Reagents 404 and 425 with sodium sulfide and zinc hydrosulfite as conditioning agents. Although he reported recoveries of 89% from a synthetic ore and 98% from a natural ore containing azurite, malachite, chalcopyrite and chrysocolla, careful application of Jackel's method to chrysocolla from Tyrone, N.M., failed to give a high recovery. MATERIALS AND TECHNIQUE Samples from Inspiration, Ariz., and Tyrone and Magdalena, N. M., were used for experimentation and verified as true chrysocolla by leaching tests, specific gravity tests and X-ray diffraction. Chrysocolla does not dissolve at pH 4, although malachite and azurite do. Chrysocolla is about half as dense as the copper carbonates. X-ray diffraction analyses by the powder camera method confirmed the samples as true chrysocolla. A captive bubble apparatus, which cast an enlarged image of the air bubble and the mineral surface upon a screen, was used to check on the character of the surfaces. The specimens were prepared by grinding a flat surface on a glass plate using fine abrasive; then they were washed and kept in distilled water until they were to be treated with reagents. Before each reagent treatment, the specimen was carefully checked for cleanliness in the captive bubble apparatus. It was assumed that the surface was clean if, after fine grinding and washing of the specimen, the bubble would not stick. Specimens were handled with glass forceps, and precautions were taken to avoid contamination of the mineral surfaces. Contact angle measurements were carefully made several times on each treated specimen to obtain reliable average values. EFFECT OF pH VALUE AND SODIUM SULFIDE CONCENTRATION In each experiment, a specimen with a freshly ground surface was immersed for 10 min in a solution of sodium sulfide, washed and immersed for 15 min in a solution containing 30 mg per 1 of potassium amyl xanthate. The specimen was then washed again in distilled water and tested for contact angle in the captive bubble apparatus while submerged in distilled water. In this series of experiments, the pH of the sulfidizing solution was varied from 3 to 7, and the concentration of sodium sulfide, containing 60% Na2S, was varied from 50 to 650 mg per 1. Many combinations of pH value and sulfide concentration resulted in no contact between the bubble and the surface, but over a limited range of conditions, contact angles varying from 24ºto 52ºwere obtained. The data in Fig. 1 show sulfidization conditions that lead to bubble contact and those that do not. The region of contact is surprisingly small, which may indicate why flotation of chrysocolla involving sulfidization has proven so difficult in practice. Several features of the system are illustrated in Fig. 1. In the region between pH values of 4 and 6 with sodium sulfide concentrations below about 350

Jan 1, 1963

By S. L. Weber, Y. H. Cheng, D. E. Banks, J. K. H. Ma

"The aggressive industrialization of America, the development of powered tools which generated massive amounts of respirable-sized dust particles, a latency period which may mask the relationship between exposure and development of disease, inadequate (or perhaps even careless) understanding of the relationship between dust exposure and disease, and respiratory protection which has later proven to be inadequate have resulted in a series of epidemics of silicosis which have caused the premature death of many workers.1-11 Emphasis on the regulatory control of dust levels in the workplace has greatly reduced the development of pneumoconiosis in the United States and in other developed as well as underdeveloped countries, yet the prevention of silicosis or coal workers' pneumoconiosis has not come close to being accomplished. Despite the public health perspective that pneumoconiosis arc totally preventable illnesses, there appears to be little evidence that this is the case.Cases of pneumoconiosis continue despite aggressive enforcement policies by regulatory agencies, attempts at dissemination of very readable materials aimed at workers and management 12.13 and respiratory dust exposure standards which are in place and appear, for the most part, protectivc.14- 16 It is more than frustrating for all parties associated with advocating workers' health to see reports of workers with aggressive silicosis. On another level, both the physician and the affected worker are helpless when a diagnosis of silicosis or coal workers' pneumoconiosis is made. Both realize that there is no proven way to affect the natural history of these progressive inflammatory and fibrotic processes. Neither is there any ""compassionate use"" therapy. What must be developed, at the very least, is a ""salvage therapy"" which has the potential to reverse, or at least dramatically lessen, the aggressive natural history of silicosis which develops over relatively short time periods. Because of the aggressive nature of silicosis (compared to coal workers' pneumoconiosis) attempting to develop a therapy for this illness should be a priority."

Nov 1, 1995

By Jose Luis Lopez Mendez

In May 1992, MEXICANA DE CANANEA, S.A. DE C.V. finalized the life of its Reverberatory Furnace which lasted 16 years. This created the need to prepare the Smelter for the next campaign.

Jan 1, 1994

By L. Andrews, G. Smits, M. D. Adams, E. A. Viljoen

A new approach has been developed that is capable of ascertaining the ore component that is responsible for the preg­robbing of pregnant pulps. Many gold mines are currently treating ores containing a component that is detrimental to the recovery of gold, in that they "preg-rob" the pregnant pulp by adsorption of some of the dissolved gold. The identity of the preg-robbing component in this type of ore has been the subject of considerable debate over a lengthy period, th various suggestions including amorphous carbon, chlonte, chalcopyrite and layered silicates, such as the phyllosilicate minerals pyrophyllite, kaolinite, phlogopite and illite. A means is now available to identify and characterize the preg-robber in gold ores. This new approach consists of contacting the ore with a synthetic aurocyanide solution, identifying the mineral grains by optical microscopy and analysing each grain individually using high-sensitivity electron microprobe analysis. The approach is exemplified in this initial study by identifying the preg-robbing component in an active sample of gold-bearing shale to be an amorphous carbonaceous phase consisting of discrete particles of about 5 µm diameter interspersed with shale particles and agglomerated into grains of up to 100 µm diameter. Microanalysis of these grains as well as other mineral particles revealed that the gold content of some of the carbonaceous grains was close to 7000 g,lt, with no gold being detected in any of the other mineral phases that were found to be present (e.g. quartz, chlorite, muscovite, pyrophyllite, etc). Bulk analysis of the sample for carbon and gold confirmed that gold loadings of around 7000 g,/t would be expected if all of the gold were adsorbed onto the carbonaceous component. The carbonaceous constituent is probably also responsible for the anomalously high surface area measured for the material. It probably acts in a similar fashion to activated carbon, and the correct choice of organic blinding agent will decrease the extent of preg-robbing by lowering the activity of the material for gold, without causing any downstream problems such as fouling of the activated carbon used for gold recovery

Jan 1, 1993

By N. Aouad

Dump truck operators are exposed to whole-body vibration (WBV) levels that exceed the International Standard Organization (ISO) 2631-1. The WBV level measured by RMS acceleration value, for operator comfort, and long-term health and safety is under 0.315 m/s2 by these standards. However, fundamental research by Frimpong and Aouad (2009, 2012) and field experimental study by Kumar (1999) have shown that operators are exposed to extreme WBV levels exposing them to injuries and musculoskeletal diseases in the long-term. These extreme WBV values in the vertical direction are equal to 3.56 m/s2, 1.12 m/s2 and 0.87 m/s2 for the operator?s seat, lower-back and cervical regions, respectively. This paper will outline current research to solve these problems. Keywords: WBV, Truck Vibrations, MSC.ADAMS, Virtual Prototyping

Feb 27, 2013

By R. Hemp

The first part of this paper describes the collection of barometric pressure measurements in a mine and their statistical analysis, which shows the effect of variations in barometric pressure, both on the primary emissions of methane gas into the workings (whether from fissures or from the surrounding strata), and on the flow of air to and from large unventilated, or poorly ventilated, areas. The second part of the paper deals with a study, based on computer simulations, of leakage flows of air into and out of sealed areas, and the reduction of such flows by the use of adequate seals.

Jan 1, 1994

By W. C. MENDENHALL

THE problem of maintaining the mining industry is two-fold; finding new supplies in the face of increasing difficulties, and making such advances in the arts of extraction and preparation as to use supplies of lower grade. Progress in mining and reduction methods and in transportation makes ore today of that which was waste yesterday. These are the fields of the metallurgists and the transportation engineers. The geologists and mining engineers must work together on the problem of ore finding. As the old prospector fades from the scene, men with equal hardihood and patience and equal power to meet the physical obstacles which confront the seeker after ore, must take his place, armed with all that has been learned from human experience about the causes, the controlling conditions, the indications, and hiding places of the metals. Such a seeker is dealing with some of the most complex and obscure of natural phenomena. In nature's laboratory, tremendous forces are at work. Tempera-

Jan 1, 1926

By F. E. Harris

IT has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-1. If the term used for carbon concentration is weight pct C, as is customary, then a factor must be found, changing this term to one of weight per unit volume when the diffusion coefficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expreses an evaluation of unsteady flow whereby .0 is given a relationship with the numerical value of C-X slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-X curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. No such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. THE STEADY STATE DIFFUSION OF CARBON IN AUSTENITE The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.1 For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase, carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid settles down towards its steady state value. At points well removed from the ends, the concentration will remain the same along planes parallel to the surfaces of the plate.

Jan 1, 1947

By Allan A. Este, Bruce Arthur

"Rio Algom's Stanleigh Mine and Mill Operation Was' officially started up in August 1983. In September 1982, Rio Algom contracted Estonix International Inc. from Lively, Ontario, to develop and implement two innovative programs: (1) Work Renovation Planning, and (2) Systems Performance Training. This paper deals with the development and implementation of these two concepts relative to the plants technology from start-up to present and the exceptional results achieved. This paper discusses how a small but motivated workforce resulted in the smooth transition from startup to full production. It also deals with how these concepts were applied elsewhere in the organization which permitted a successful transition and downsizing of the over-all operation.IntroductionRio Algom Limited produces uranium in Elliot Lake, Ontario. In the late 1970s Rio Algom entered a contract with Ontario Hydro to supply uranium from its Stanleigh property, which had been idle since 1960. The mine was subsequently upgraded, and a new modem mill was designed and built, commencing operation in 1983.From then until September 1990,Rio Algom had three producing mines and mills in the Elliot Lake area. Quirke mill, with a capacity of 6350 tonnes per day, operated continuously from 1968. The Panel mill with a 3000 tonnes per day capacity, operated since 1979. Stanleigh mill continues to operate under long-term contracts, although at a production rate about 25070 lower than its rated capacity of 5000 tonnes per day.Both the Quirke and Panel mills, although not entirely similar, were conventional uranium mills utilizing crushing, grinding, leaching and ion exchange. As such, and in keeping with the traditional management style, there was a rather large mill operating workforce, which utilized a line-of-progression job classification system."

Jan 1, 1993

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By P Marlow

Raiseboring is an attractive method of constructing shafts, being safe, fast and comparatively cheap. But this means back-reaming through weathered ground. However in the gravels and weathered near-surface rocks typical of the Western Australian goldfields, back reaming large diameter shafts through to the surface is risky and conventional sinking from surface has normally been required.An alternative construction approach has recently been used to stabilise the weak surficial materials and allow raiseboring through to the surface. The method is based on first installing rings of non-contiguous reinforced bored piles around the shaft perimeter, for temporary support, then back reaming shafts at full diameter through to the surface. Immediately after the reaming head is removed, the weak exposed materials are supported using remotely sprayed fibrecrete.The method has been successfully applied to four shafts since July 2007; 3 m and 4 m diameter shafts at Trident Mine, a 3 m diameter shaft at Wattle Dam and a 4.5 m diameter shaft at Athena Mine.Bored pile layout designs have varied from eight to 24 piles, of diameters 120 to 270 mm, in one or two rings. In one case, the top 10 m of the proposed shaft was pregrouted. Subsequent surveys have confirmed that fallout occurred in some shafts, out to the ring of piles, implying that the piles inhibited collapse.The practical implementation of the method was not always easy and many valuable lessons have been learnt. This paper documents key aspects of the method and the critical elements for its application.

Mar 21, 2011

By Herbert Hoover

BOTH the directors of industry and your leaders have made great progress toward a new and common . ground in economic conceptions, which, I am confident, has had a profound effect upon our economic progress during the last few years. That is the conception that industry must be constantly renovated by scientific research and invention; that labor welcomes those labor-saving devices; that labor gives its full and unrestricted effort to reduce costs by the use of these machines and methods; that the savings from these reduced costs shall be shared among labor, employer and the consumer.

Jan 1, 1930

By Tim Hurley

On Friday, May 27, 1983 at about 6 p.m., an avalanche occurred at the Revenue-Virginius Mine. Six mine personnel and two contract diamond drillers were trapped when the avalanche covered and blocked the portal, the only access into the mine. The San Juan Mountain Range in southwestern Colorado is an old volcanic caldera. It has dikes and other intrusions, many of which are mineralized with sulfide ores rich in silver, gold, lead, zinc and copper. Several peaks rise above 4,260 m (14,000 ft) and the district has been the location of avalanches dating back to prehistoric times. This is evidenced by the numerous snow-slide chutes that are infamous enough to be named on topographic maps.

Jan 1, 2006

By G. Danko

Ventilation and refrigeration for mine climate modification, contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can be used to minimize the impact of these costs. There are several computer codes available including CLIMSIM?, to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely: what accuracy is required of the basic input parameters, in order for a certain precision to be obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel's superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed to the changes of the rock thermo-physical properties, the heat transfer coefficient and the wetness factor.

Jan 1, 1988

By Valentine A. Chanturiya

A model for development of electric discharges between particles of sulfide minerals (pyrite) under the action of high-voltage nanosecond pulses is proposed. It is shown that through discharges in a layer of pyrite particles lead to energy concentration in small contact regions between particles; the concentrated energy is sufficiently high for local disintegration of mineral complexes.

Jan 1, 2009

By Thomas A. Phillips

The Bureau of dines present, an economic evaluation of its process for the ferric chloride leaching of chalcopyrite concentrate. In this process, chalcopyrite concentrate is leached with ferric chloride solution to extract copper, which is precipitated from the solution by electrolysis while leaving sulfur in the residue. Spent liquor from electrolysis is treated with oxygen to regenerate the ferric chloride leach solution and the sulfur-laden residue is processed to recover the sulfur. A cost estimate was prepared for a plant capable of processing 600 tons of chalcopyrite concentrate per day, 330 days per year. The fixed capital cost, on an early 1.975 basis is $27,831,600 and the estimated operating cost is 9.9 cents, per pound of copper product. In comparison, the estimated operating cost of a smelter equipped with a citrate process plant to recover sulfur is about 13.6 cents per pound of copper product. No charge for chalcopyrite concentrate or credit for recovered byproducts has been included in either operating cost. The ferric chloride leach process, therefore, appears to be economically attractive.

Jan 1, 1976