Search Documents

By David Hatton, Jacques van Wyngaard, Matheus Vilarinho, Neymayer Pereira Lima

The flotation of Brazilian fine iron ore particles presents well-documented challenges, particularly the high entrainment of iron into the quartz (tailings) stream, resulting in significant iron losses and reduced circuit efficiency. This paper evaluates the application of Woodgrove’s Direct Flotation Reactor (DFR®) technology, which has been piloted by Vale as a potential solution to these challenges. The DFR is assessed from a pilot scale and process design perspective, with emphasis on its staged flotation mechanism, energy dissipation characteristics, and concentrate handling mechanism that together collectively enhance the selective recovery of fine iron particles. The DFR’s operation is contrasted with conventional tank cells, highlighting its improved control over bubble-particle interactions, reduced entrainment, and potential for higher selectivity. The DFR pilot plant was used to perform reverse cationic flotation of a quartz-rich froth phase to upgrade the iron ore. Pilot plant results are presented, comparing DFR performance with pilot-scale conventional flotation tests on the same feed material and relevant industrial benchmarks. This paper compares a conventional mechanical cell circuit performance and design with a proposed DFR configuration for two -45μm deslimed size fraction samples, analysing parameters such as footprint, energy efficiency, reagent consumption, and overall metallurgical performance. The findings show that DFR technology has the potential to significantly improve the fine hematite selectivity in quartz flotation for iron ore applications, offering a pathway to increased resource efficiency and reduced losses to tailings.

May 2, 2026

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from the underlying unoxidized ore through prolonged Weathering. The degree of oxidation in different sections and at different depths within the bed is not uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By R. E. Lindstrom

The mineral bastnasite is utilized to describe alternate processes for the extraction and separation of the rare-earth elements by solvent extraction. The rare earths can be acid-leached directly or fused with NaOH before acid leaching. Cerium, the major constituent, can be recovered by fractional precipitation, fractional leaching, or solvent extraction with tri-nbutyl phosphate. The latter process is capable of producing 99.5-percent pure CeO2 at 98+ percent recovery. Lanthanum is subsequently recovered by fractional precipitation or solvent extraction with a nitrogen-based extractant. A 20-stage mixer-settler operation with a primary amine extractant results in a 95-percent pure La203 fraction at 96 percent recovery. Europium is amenable to extraction from most of the remaining rare earths with an organophosphate extractant. Selective stripping of the europium, followed by reductive precipitation, produces high-purity Eu203. Another possibility for europium purification involves the differential extraction of europium with an amine followed by a sub- sequent reducing strip. Separation of the remaining elements is more difficult but can be accomplished with amine or quaternary ammonium extracts. Typical separation factors achieved are 3. 8 for praseodymium-neodymium and 10. 5 for neodymium-samarium.

Jan 1, 1967

By M. Fornaro, E. Lovera, I. Sacerdote

"The analysis of the mining laws of the different European States reveals big diversities and, often, remarkable complications. This is due, firstly, to the history and culture of different States and, secondly, to the assets of natural resources. It is therefore difficult to find a common line between the text of the various mining laws, but it can be observed that nearly all the States distinguish the mining resources in two categories: the materials whose importance is considered strategic belong to the first category; in the second category the materials whose importance (above all economic) is mainly local are comprised. The paper, analysing in detail the planning procedures in some important Countries, investigates the possible perspectives of arranging some guide-lines for a correct approach to the sustainable exploitation planning/programming of mineral resources (with particular reference to "quarry" materials, such as aggregates), considering both the environment protection and the production needs."

Jan 1, 2005

By K. Winterton, Carruthers. J.

"Attempts have been made to produce hardened structures of a pseudomorphic type in various carbon and alloy steels. In order to obtain martensite with a fine distribution of cementite, an initial structure of fine lamellar or nodular pearlite is required; this may be obtained by conventional means. This is followed by partial austenitization and quenching.Two methods have been tried to induce partial austenitization:(a) A resistance (direct current) heating method involving rapid entry into the austenite field.(b) A new method, described as the ""threshold"" technique, involving homogenization of temperature just below A 1, followed by entry into the austenite field; two furnaces are required.The resulting structures have been examined for microstructures, hardness, tensile, and impact values. The tensile properties are comparable with those obtainable by conventional treatment methods. Impact values are disappointing, but this is explainable from the nature of the manifold changes occurring."

Jan 1, 1960

By Takayuki Sakai, Takefumi Takuma, Lee Roesner

"70-foot deep rectangular-shaped bulkheads were built with sheet piles as launching and receiving shafts for a pipe jacking operation for new underground waterlines in a densely populated section of Los Angeles, California. The Press-in Piling Method was specified to drive 95-foot long sheets (a record for the method) to form the bulkheads for the Los Angeles Department of Water and Power’s LA-29 (DWP) Connection Modification and Pipe Jacking. The piling was chosen because of its very low noise and practically vibration-free nature since the site is surrounded by houses, an apartment complex, and existing water lines. The out front areas of the bulkheads were grouted to let the TBM go through without major ground water leaks. Hydrophilic foam grout was also injected in addition to welding steel scab plates on the inside to seal them to achieve sufficient watertightness behind a few split interlocks. BACKGROUND This project was located in the Crescent Heights area of Los Angeles which is a few miles south of Beverly Hills. The project represents the completion of the last phase of the Stone Hollywood Trunk Line. This was an 8-mile long water trunk line that averaged 60 inches in diameter and was built to improve the reliability of the DWP’s major water system. This section of the project involved driving 2 deep shafts to allow for the installation of a 350-foot-long 72-inch steel casing using microtunneling construction. See Figure 1 for the shaft locations and the tunnel alignment. The challenge for the project was that this water line would have to pass beneath the Hollyhills buried box drain (15 feet high by 20 feet wide). Further complicating the construction was the soils beneath the drain. The DWP chose to drive the tunnel at a depth of approximately 65 feet to ensure that the ground conditions were uniform and suitable for the microtunneling equipment. There were two previous attempts to construct this work which failed because of poor ground conditions and very high water levels. This third attempt was critical because the DWP could not afford to have another failure due to the fallout with the residents being impacted by the project."

Jan 1, 2016

By B. Yu, M-H. Cao, C. Zhou, X-Z. Zhang

The transient infiltration and lubrication behaviour of slag during continuous casting of steel is important for billet quality. A two-dimensional coupled mathematical mould model was developed to investigate these phenomena. The accuracy of the model was verified by comparing the calculated slag consumption with measurements by the plant. The results show that the liquid slag is consumed from the middle and late period of positive strip time to the next early period of positive strip time, including the entire negative strip time. The maximum downward infiltration velocity and positive pressure in the slag channel is at the middle of the negative strip time. Increasing the positive pressure of the slag channel is conducive to lubrication. The shear stresses acting on the shell surface and at the mould side were determined by the lubrication slag consumption and total slag consumption, respectively, and gradually decreased with increasing slag consumption. The negative strip time was lengthened to increase the slag consumption and prolong the time near the maximum downward shear stress, so as to be conducive to the demould.

Apr 16, 2024

By R. J. Chase, C. Davies

"Abstract- The Merelani graphite-tanzanite deposit is located in northeast Tanzania, 14 kilometers south of Kilirnajaro International Airport and in close proximity to the towns of Moshi and Arusha . The graphite mineralization is hosted by relatively undeformed linear Proterowic metasedimentary gneisses, several of which have been subjected to hydrothermal alteration resulting in tanzanite mineralization. Exploration work comprised detailed geological mapping coupled with pit and trench channel sampling and a subsequent 1500 meters of diamond drilling. In addition, metallurgical tests have shown the graphite to be of unusually coarse flake size, crystallinity and high purity.Feasibility studies have shown the economic viability of a major coarse flake graphite deposit with the measured resource to 50 meters in excess of 9 million tonnes assaying over 8o/o graphitic carbon . Production is due to start by the end of the first quarter of 1994 with the processing plant design capacity initially set at 15 000 tonnes per annum.ln addition to graphite production, tanzanite will be produced through selective mining within the graphite open pit in the upper horizon and from underground workings within the lower horizon.The Merelani graphite-tanzanite deposit will be the first major orebody to be exploited through means of private funding since Tanzania gained independence."

Jan 1, 1994

By Myers, J. F.

The purpose of the mill tests reported herein, was to determine the relative power efficiency of fast and slow rod mill speeds on the ores of the Tennessee Copper Co. The tests were carried out at the lsabella Mill of the Tennessee Copper Co. under normal operating conditions. Every effort was made to keep the ore supply and other conditions constant, but it will be noted that some slight variation did occur. The open circuit 6 by 9 rod mill, and ore, used in these tests have been previously described.' Four motor drive pinions were available and the tests were performed in the following manner: each pinion was used to drive the mill for a period of one week. Constant sampling prevailed during the test run, and a composite sample for each speed test was made. Realizing that some slight liner wear took place during the four-week test-run, and that some slight variation of the ore may have taken place, a second and then a third series of four-week test- runs were made with the four different pinions. The screen analysis of each of the thee-week run samples at the various speeds were composited and the results are shown in Table 1. The authors feel that the 12 weeks of operation consumed during these test-runs would represent fairly the effect of each mill speed. The data of line 37 show that within the error of sampling and plant operation, the tons of minus 65-mesh material generated per horsepower hour was the same at all four speeds.

Jan 1, 1949

By Yves Boissonnas, Marco Bettelini

"INTRODUCTION AND OBJECTIVES The operational safety of long and very long rail tunnels represents a key issue in all development stages, including design, construction, commissioning and operation. The spectrum of potential threats is very broad and challenging. These issues can only be mastered by means of a proper combination of a number of safety measures at various levels. This paper focuses on the specific safety issues and the extremely challenging conditions characterizing very long and deep tunnels. They include a significantly increased risk during operation that the incident train cannot exit the tunnel by its own means, long self-rescue and rescue distances, the presence of a number of trains, possibly mixed traffic as well as significant thermal issues. Amberg Engineering is strongly involved in the design and construction of most long and very long rail tunnels in Europe, including in particular the Gotthard Base Tunnel (GBT), Lyon-Turin Base Tunnel (LTF) and the Brenner Base Tunnel (BBT). The combined experience arising from these tunnels forms an invaluable body of expertise, which is summarized in this paper. The focus is on shared issues with practical relevant examples and project-specific solutions. Special attention will be devoted to the 57 km long Gotthard Base Tunnel, which will be operational by mid-2016 and will be the longest infrastructure tunnel worldwide. VERY LONG TUNNELS IN EUROPE Overview From the point of view of safety, tunnels in excess of about 20 km exhibit a significantly increased risk that incident trains could stop within the tunnel. This is related to the European Technical Specifications for Interoperability (TSI) on rolling stock, to be discussed in the chapter on rescue stations. This paper will specifically focus on the following longest tunnels in construction or operation, listed in Table 1."

Jan 1, 2016

By E. M. Cox, A. S. Skapski, N. H. Nachtrieb, M. C. Bachelder

As a result of using copper-containing scrap in the steelmaking process, the copper content of steels has been steadily increasing for years. Consequently the possible role copper may play in the steelmaking process and in the finished product begins to attract the metallurgists' attention. Some time ago one of the present authors forwarded the idea—based on the results of the analysis of nonmetallic inclusions extracted electrolytically from steels—that sulphur in plain carbon steels is distributed mainly between copper and manganese, the amount of iron sulphide being very small; and that, consequently, the problem of copper and that of sulphur in steel cannot be treated separately.' At the time of the publication of the quoted paper little was known about the relative affinities of copper and manganese for sulphur at high temperatures except that at moderate temperatures (below 1000°C) the affinity of manganese for sulphur is much greater. To gather more experimental data on this subject, the present authors undertook the investigation of the equilibrium constants of the reactions: 2Mn(8 or 1) + S2(g) = 2MnS(s) 4Cu(s or 1) + S2(g) = 2Cu2S (S or I)* 2Fe(s) + S2(g) = 2FeS (s or 1) over a range of temperatures wide enough to establish the dependence of these equilibrium constants on temperature. From the equilibrium constants (K = l/Ps2) the free energy of formation (affinity) can be calculated from F° = -RTln 1/PSt (1) where the standard conditions chosen are: 1 atm of sulphur pressure and the activities of condensed components equal one. The decomposition pressure, Ps2, of sulphur over the respective sulphides is too small to be measured directly, but there is a way of eliminating this difficulty by measuring the equilibrium constant of the reaction between the sulphide and hydrogen. From the latter and from the equilibrium constant of the thermal dissociation of H2S we then calculate Ps2 for the respective sulphide. 2Mn + 2H2S = 2MnS + 2H, 2H2 + S2 = 2H2S_________ 2Mn + S2 = 2MnS The numerical values of the equilibrium constant of the thermal dissociation of H2S at different temperatures were taken from Kelley's paper, "The Thermodynamic Properties of Sulfur and its Inorganic Compounds."² In previous experimental work published by Jellinek and Zakowski3 and by Britzke and Kapustinsky4 the equilibrium constants of the reactions Metal sulphide + H2 = H2S + metal were determined by passing hydrogen, at different rates of flow, over the sulphide, analyzing the resulting H2S + H2 mixture and then extrapolating the H2S/H2 ratio (which is a function of the rate of flow) to the zero speed of flow, a method necessarily involving considerable uncertainty. In the present work the equilibrium ratio was actually measured instead of being extrapolated. The apparatus is shown in Fig 1. Experimental Procedure The sulphides were prepared by the following methods: FeS Powdered iron which had been reduced with hydrogen (ferrum reduc-tum) was mixed in stoichiometric ratio with sublimed sulphur and carefully ground. The mixture was put into an alundum crucible, covered with pure sulphur, and the reaction started by touching the mixture with a glowing iron rod. After the reaction was completed the product (still containing some metallic iron) was again ground with sulphur, put into a Rose crucible, covered with sulphur, and heated in a strong current of pure hydrogen. Analysis of the final product showed 62.46 pct Fe and 36.59 pct S. Theoretical for FeS: 63.53 pct Fe and 36.47 pct S. MnS Manganese sulphide (precipitated and carefully washed with distilled water containing H2S) was dried in a Rose crucible in an atmosphere of H2S and heated in a current of hydrogen for 2 hr at red heat. The product was then ground and ignited for several hours at 1000°C in a current of hydrogen sulphide. Analysis showed 64.53 pct Mn and 36.63 pct S. Theoretical: 63.15 pct Mn and 36.85 pct S. Some MnS samples were prepared from metallic manganese and sublimed sulphur by mixing and grinding them and then heating in a current of hydrogen sulphide in an alundum tube.

Jan 1, 1950

By Arthur L. Murray

"Putting safety over , " using the accepted meaning of the word " Safety " as the elimination of personal injury , resolves itself into the prevention or disassociation of a combination of two distinct circumstances . Opportunity for accidents is afforded by conditions that are likely to cause injuries , but such injuries are effected only when the human body is placed in a position to be injured . As will be discussed later , in mining , as in most other industries , the degree of safety experienced depends upon the disassociation of these two circumstances , first , by making working conditions as free from hazards as possible , thus affording the minimum opportunity for accidents to occur , and secondly , the training of employees to recognize dangerous conditions and adopt measures to protect themselves and their fellow employees against injury . The responsibility for preventing accidents rests upon every person employed in an industry from the directing head down through the individual workers , and the safety of that industry will be proportionate to the extent that each member appreciates and accepts his individual responsibility . Hence , safety becomes decidedly a personal equation . Whether the personal equation will be so applied as to result in the greatest freedom from accidents , however , depends largely upon the initiative of those directing the industry . Putting safety over in a small mine presents the personal equation in a more intensified manner than the same endeavor in a large mine . Large mines , owing to their size and financial standing, can usually main ta in and support an effective safety organization with one or more directors who devote all their time to the supervision of safety work . Most small mines with a limited number of employees and limited capital can not afford and are not justified in supporting a paid safety organization , and must depend upon the close cooperation of their working force in maintaining safe working conditions . On the other hand , if proper supervision is exercised the small mine has in some respects advantages not afforded by the large mine . The limited workings in a small mine should afford less opportunities for dangerous conditions to arise and permits more frequent inspection of the entire mine . The small working force permits more latitude in the selection of employees known or believed to be either safe workers or amenable to safety educational work. Likewise , a small working force facilitates the carrying on of safety educational work and allows a closer personal contact between the superintendent and his employees .

Mar 1, 1923

By D. I. Verrelli

Within the flotation community a belief has developed that some particle shapes are more ?floatable? than others. This is usually attributed to an influence of particle shape or roughness on the induction period required to achieve attachment between the particles and the air bubbles in the pulp. Up to now, such measurements have not been able to readily isolate the effect on individual flotation subprocesses. In contrast, our experimental apparatus, the CSIRO Milli-Timer, enables us to directly observe the process of particle?bubble interaction and attachment by means of a high-speed video recording, thus providing a direct measure of the induction period for attachment. To assess the influence of particle shape on induction time we used two varieties of methylated borosilicate glass particles ? spheres and angular ?frit? ? in a range of tightly-sized fractions. In doing this, we take care to account for the influence of other factors that could affect the induction time, such as the polar angle of sliding commencement, and approach velocity. These parameters are recorded as variables for each interaction, and corrected for using multiple nonlinear regression. Our results illustrate the importance of particle shape on induction period, with angular particles exhibiting induction periods that were an order of magnitude lower than those of spheres. Furthermore, the induction period was seen to decrease with increasing particle velocity, or kinetic energy on approach, but increased as the trajectory approached the limit of just grazing the bubble. Particle shape in mineral processing is a consequence chiefly of the mineral type and the type of grinding employed. The results presented herein indicate that attention should be paid to the shape of particles obtained from the grinding operation, besides particle size. Keywords: attachment, bubbles, flotation, induction period, particles, shape effects, surface roughness

Sep 1, 2012

By M. W. BERNEWITZ

DURING my recent extended visit to Australia and New Zealand, these notes on oil and gas prospecting in that part of the world were compiled from recent reports-press and government, from conversation with one of the financial leaders in the search for oil, and from personal observation of operations of the principal importers, blenders, and distributors of oil products; also from the astonishing testimony given by them to the Petrol Commission. Australia and New Zealand have practically no petroleum production beyond a few thousand gallons a year from wells in the latter Dominion. Everything is imported, Table 1. showing the quantities for 1929-30 in Australia and for 1930 in New Zealand,

Jan 1, 1934

By G. Chung, W. Petruk, D. Doyle

"A series of tests was conducted on Carol Lake iron ore, which contains about 38 wt % hematite and 19 wt % magnetite, to establish a flowsheet for high weight yield by spirals. A pilot plant was run in parallel with the IOC concentrator to simultaneously test two flowsheets on the same feed material. The IOC concentrator processes the ore by treating it directly in a spiral circuit, whereas the pilot plant used a laconite flowsheet which had a low intensity magnetic separator (LIMS) at the front of the circuit. The LIMS produced a non-magnetic (hematite-rich) product and a magnetic (magnetite-rich) product prior to treating the ore in two separate spiral circuits. The results from about 150 tests were evaluated by chemical assays and materials balancing techniques, and a selected test was evaluated by the image analysis and materials balancing technique.The image analysis and materials balancing evaluation showed that a higher hematite recovery was obtained by the hematite spiral circuit than by the IOC concentrator spiral circuit, and a slightly lower magnetite recovery by the magnetite spiral circuit than by the IOC concentrator spiral circuit. Furthermore the hematite recovery by hematite spirals was higher than the magnetite recovery by magnetite spirals. The better hematite recovery was achieved because a higher liberation is obtained for hematite than for magnetite, and the hematite in the Carol Lake ore has a narrower grain size range than magnetite. Consequently, better spiral control can be maintained when processing a hematite-rich spiral feed, than when processing a magnetite-rich spiral feed. Since the feed to the IOC concentrator spiral is a mixture of hematite and magnetite, an intermediate hematite recovery is obtained by the IOC concentrator. INTRODUCTIONA study of characteristics that affect recoveries of hematite and magnetite from the Carol Lake ores of the Iron Ore Company of Canada (IOC), was carried out in connection with a project on designing a flowsheet for maximum weight yields. A pilot plant using a taconite flowsheet was run in parallel with the existing IOC concentrator which uses a classical iron ore flowsheet. About 150 tests were run to compare iron recoveries and weight yields by the spirals in the two flowsheets. Better iron recoveries were indicated for the taconite flowsheet, but the results were not consistent and the reasons for the observed differences were not apparent. The material from one test (Test 61), which gave better iron recoveries for the taconite flowsheet, was evaluated by the image analysis and materials balancing technique. A suite of samples was taken from 5 points in the IOC concentrator and from 8 points in a pilot plant (taconite flowsheet). The samples were analyzed to compare the behaviours of the Carol Lake hematite and magnetite in the spirals of the two flowsheets. The results provided a sound basis for further tests in designing a high weight yield flow sheet."

Jan 1, 1993

By Clara Godoy, Paulo Couceiro, Juan Navarro

The continuous automatization and digitalization of the different stages involved in any underground construction bring new possibilities to optimize the operation. One of the most important requirements for the development of these projects consist of a proper rock mass characterization for optimizing the stages of the drilling, blasting and support cycle. In the last few years the road to digitalization has gone through data science and big data, showing the importance of data gathered to describe the geological and geotechnical environment that surrounds the operations. Since rock characteristics have an important influence in the drilling response, the technological advances in the sensorization of drilling machinery such as the Measurement While Drilling system (MWD) allow to gather the necessary amount of information to be applied in data science processes to evaluate changes in the rock mass with higher resolution than conventional methods. In this paper, Machine Learning techniques have been used to combine data monitored from the drill rigwith scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure. Considering blasting factors as constant, the model combines the rotary, percussive, hydraulic flushing and the rate of advance of the drilling, and the confinement of the rock mass by depth, to detect zones with different rock properties. This provide an early information of the rock mass condition around the blastholes and the prediction of expected overbreak generated after blasting, being possible to design more efficient bastings, in which each borehole is filled with the right and necessary explosive charge. The analysis comprises data from 57 blasts (around 1700 contour blastholes) and more than 4000 excavated sections.

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By Peter G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the information necessary in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included the following : (1) careful checks on the sampling and assaying (2) selection of representative samples used to establish the recoverable amounts of precious metals in the ore (3) examination of underground workings driven to provide samples both for metallurgical testing and for assay comparisons (4) evaluation of plant site and waste dump areas as non-mineral, including a placer examination of the taillngs disposal area (5) location of an adequate water supply. All these investigations were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1981

By Peter R. Drummond

THE paper consists of four sections: (1) a discussion of early work; (2) presentation of the results of a chemical investigation of Falcon-bridge nickel-copper blast-furnace matte; (3) application of the results of this investigation to mattes in general; and ( 4) a summary of conclusions. All general discussion will be confined to the fundamental system of ferrous-cuprous sulphides (FeS-Cu2S). Nickel-, lead-, and zinc-bearing mattes will be treated as minor varieties of the parent system. DISCUSSION OF EARLY INVESTIGATIONS Matte investigations may be divided into three classes: first, those treating the sulphides as alloys-theoretical studies of the system FeS-Cu2S, such as those of Hofman (ll)t or Carpenter and Hayward (2); second, chemical research on mattes made under smelter conditions, such as that carried out by Hawley (3) or Avetision ( 4); third, combinations of the . above, such as the investigations of Gibb and Philp (5) or Fulton and Goodner (6). Much research in the first of these classes, including determinations of . freezing points and of data for structure-composition diagrams of the system FeS-Cu2S, was carried out in the period 1890-1910. LeChatelier and Ziegler (1, 13) proved that FeS, when heated alone above its melting point, dissociated in part, and Friedrich ( quoted by Fulton, 6) showed the same for Cu2S. The reactions may be expressed by the following equations: [xFeS yFe + yS (volatilized)+ (x -y)FeS xCu2S )'Cu+ yS ( vohtilized) + (x -)')Cu,S ] Sulphur is lost by volatilization, leaving a melt of metallic iron plus ferrous sulphide in the one case, and of metallic copper plus cuprous sulphide in the other. If the mixed sulphides are heated far above their melting points, there results either an iron-rich matte containing Fe-FeS-Cu2S or a copper-rich matte containing FeS-Cu2S3-Cu, depending on the relative amounts of each sulphide in the mixture.

Jan 1, 1940

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11/2 inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219c. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: 1, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.