Search Documents

By N J. Grigg

Gekko Systems has developed an underground pre-concentration plant (Python) to reduce mine operating costs. Many ores liberate favourably using either high pressure grinding rolls (HPGR) or vertical shaft impactors (VSI). Using these comminution circuits for mineral liberation; rather than for the final recovery process and by utilising a high mass pull, high recovery process route (gravity/flotation), a narrow, low head, compact processing plant was developed that can sensibly be operated underground. The Python underground processing plant can provide a number of advantages for narrow vein mines including lower haulage costs, improved mine call factor and lower operating costs. The focus on fine crushing reduces the power requirement of the plant to approximately 8 kWh/tonne. The Python underground processing plant has been designed to be towed down the decline or lowered down a shaft, and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a saving in mining costs and a significantly smaller environmental footprint.

Jan 1, 2008

By N. A. D. Parlee

The diffusion rate of hydrogen in liquid iron has been measured by a gas-liquid metal diffusion cell technique. The diffusion cell was formed by immersing an alumina tube containing hydrogen gas at 1 atm in a bath of stagnant liquid iron. The change in the composition of the melt in the cell was determined by measuring the rate of absorption of the gas in the cell. The appropriate solution to Fick's second law was used to examine the data and calculate diffusivi-ties. The absorption of hydrogen in stagnant pure liquid iron has been found to be diffusion-controlled. The results show that the chemical diffusion coefficient, D, of hydrogen in pure iron in the range of 1547" to 1726°C can be represented by the following Arrhenius relation: D(sq cnz per sec) = 3.2 x X exp(- 3300 i 1800/RT) where the uncertainty in the activation energy corresponds to the YO pct confidence level. Oxygen in the melt (above 0.015 pct 2) increased the apparent rate of absorption of hydrogen. The importance of diffusion data on liquid metals for predicting the rates of certain metallurgical processes has been recognized for a long time. Moreover, these data are much needed to test and develop theory for diffusion in liquid metals. Despite this practical and theoretical interest, however, relatively little reliable information about diffusion in liquid metals is available in the literature. This is particularly true for gas components such as hydrogen, oxygen, and nitrogen in liquid metals, where almost no data on chemical diffusion coefficients are to be found. This is probably due to a multitude of experimental difficulties particularly associated with high-temperature melts. In an effort to fill this gap in information, a research program was undertaken to study the diffusivities and rates of solution of gases in liquid metals. This paper presents the results of a study of the diffusion of hydrogen in liquid iron. EXPERIMENTAL METHOD Two methods for the study of the kinetics of dissolution of gases in liquid metals are being employed in this laboratory. Both involve the measurement of the volume of gas absorbed by the melt as a function of time and as such both avoid the uncertainties involved in chemical analyses of quenched samples for relatively small amounts of gas. In the first method, the gas dissolves in an inductively stirred melt and, in the absence of a slow surface reaction, the results are often interpreted in terms of mass transport across a liquid "boundary layer" between the homogeneous gas phase and well-stirred part of the melt. Other interpretations of the results of such experiments have also been described in the literature.1'5 In the second method a gas-liquid metal diffusion cell is used.' The gas dissolves in a cylindrical column of stagnant liquid metal and, in the absence of a slow surface reaction, the results are interpreted in terms of a non-steady-state diffusion solution to Fick's second law. The weakness of the first method is that while it gives information on the mechanism of absorption by stirred melts it yields an overall rate constant which even in the simplest cases depends on the nature and the thickness of the "mass transport layer" or "boundary layer". It yields no values of diffusion coefficients. The second method was used in this research because in many cases it is possible to determine the diffusion coefficient of the gas component in the liquid metal. In this research it has been utilized to measure diffusion coefficients of hydrogen in liquid iron. The apparatus used was essentially the same as that described by Mizikar, Grace, and par lee but certain modifications have been introduced to meet the elevated temperatures and special conditions of this research. Fig. 1 is a schematic drawing of the apparatus and Table I gives the identification of various parts in this figure. The diffusion cell, shown in detail in Fig. 2, was formed by immersing an impervious alumina tube (hereafter called absorption tube) in a bath of pure liquid iron contained in an alumina crucible. Two types of tubes were used, Morganite triangle RR and McDanel AP35. The crucible was contained in a vertical impervious alumina combustion tube (32 mm ID by 914 mm long) which was closed at both ends by water-cooled brass heads employing O-ring compression seals, Fig. 1. A protection tube enclosing a Pt, 5 pct Rh-Pt, 20 pct Rh thermocouple was introduced through the lower end of the combustion tube

Jan 1, 1968

By Kurt RP Petersen, Hendriena van der Walt

With the decline in fine diamond production from the Argyle mine in Australia, there is a greater emphasis on efficiently treating the finer size fractions through a DMS circuit. Although it is generally well understood that smaller diameter cyclones are more appropriate for this application, practical results do not necessarily meet this expectation. In this paper the operational performance of particular sized cyclones throughout the group was compared. Based on the results there is evidence that under certain practical operating conditions, small cyclones are not necessarily best for fine size particle treatment, particularly given the production pressures faced by all mines. However, there seems to be considerable merit in using larger sized cyclones, which tend to exhibit less performance variability, irrespective of operation conditions.

Jan 1, 2006

By Constance F. Acton

This paper presents an overview of -- the carbon-in-pulp process for gold and silver recovery as seen in the early 1980's. Traced back to its origins in the mid-nineteenth century the process development through the present state-of-the art is described. The process technology and equipment design are described in detail for the carbon-in-pulp process. A typical process flowsheet is given with a description of appropriate design criteria. Technical advantages and disadvantages as compared to the traditional countercurrent decantation process are discussed including some illustrative comparisons of capital and operating costs. A summary of currently operating carbon-in- pulp plants throughout the world is given with an insight into future developments in this industry.

Jan 1, 1982

02, NaCI03, H202, Na0CI and Ce+4 have been examined as oxidants in an alkaline carbonate system for uranium in in situ leaching. The South Texas and New Mexico ores contained up to 2.6 meqJg of reducing compounds which consume oxidants in the leading operation. Leaching rates did not increase linearly with the oxidation potential of the oxidants. A mild oxidant can be used to maximize uranium oxidation selectively and oxidant efficiency. 02 can oxidize most of the uranium mineral with an adequate rate and high oxidant efficiency.

Jan 1, 1990

By T. T. Chen, J. L. Jambor, J. E. Dutrizac

A reconnaissance study of the neutralization potential of 30 diverse minerals, 28 of which are silicates and aluminosilicates, has shown that most of these minerals contribute minimally to the neutralization potential (NP) in standard static tests. Feldspars in particular give low NP values and would not be expected to attenuate the acidity to any significant extent in acid rock drainage settings. The BET-determined surface areas of the minerals vary considerably, and the large surface areas of some of the pulverized samples have clearly affected the NP values even though the standard static-test protocol was used for the preparation of the samples. The low NP values of most silicates and aluminosilicates are in general agreement with the laboratory-determined slow dissolution rates for these minerals. The results suggest that, in the prediction of whether rocks will be acid-producing, the most realistic measure is that of the carbonate content. In mine wastes from metalliferous ore deposits, the contribution to the NP by the non-carbonate gangue assemblage is unlikely to be more than a token amount until well after the establishment of an acid rock drainage situation.

Jan 1, 2000

By K. Terhaar

The objective was to determine operating protocols for a lead and silver column flotation cleaner, being considered for installation at Sunshine Mining & Refining Co.'s Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause and effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feed grade. The results were that xanthate, zinc sulfate, and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences were useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training, and provide a foundation for future on-line control.

Jan 1, 1999

By A. M. McKim

6, 7.3 meter diameter autogenous mills at Wabush Mines are undergoing conversion from a radial configuration of pulp discharger to a curved design. Improved discharging efficiency has effectively lowered the pulp level in the mill. The low level operation enhances the grinding efficiency netting a 12% power reduction. Significant reductions to rate of wear has been a spin off benefit. The design incorporates features for holding the assembly solidly in place thus eliminating bolt hole damage and leakers. Preliminary work in one 11 meter mill at Hibbing Taconite did not indicate that all the same advantages were available in their process.

Jan 1, 1982

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Binary alloys of titanium with silver, lead, tin, nickel, copper, beryllium, boron, silicon, chromium, molybdenum, manganese, vanadium, iron, and cobalt were studied. One-half-pound ingots of the alloys were prepared in an arc furnace, employing a water-cooled copper crucible, an argon atmosphere, and a water-cooled tungsten electrode. The half-pound ingots were fabricated by forging at 1700°F in air to 1/4-in. slab, followed by hot rolling at 1450°F to 0.060-in. sheet. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships were determined for these alloys. EARLY in 1947, as one phase of the evaluation of materials for Air Force Project RAND, Battelle successfully arc melted Bureau of Mines titanium and obtained a few basic properties of unalloyed titanium and several titanium-base alloys. The low density, excellent resistance to corrosion, and high tensile properties of these materials stimulated a great deal of interest among metallurgists and designers seeking better materials of construction. As a result of this early work, Battelle, under contract with the Air Materiel Command, Wright-Patterson Air Force Base, has continued extensive studies of titanium alloys. The result of the first year's work is described in three papers. The present one deals with binary alloys, the second with ternary alloys, and the third paper with quaternary alloys. Melting Method The arc furnace for melting titanium and other refractory metals was developed at Battelle Institute under Air Force Project RAND. During the present work, considerable improvement has been made in the design and operation of this furnace for making small ingots of titanium and titanium alloys. The improved furnace design is illustrated by fig. 1, which shows a cross-sectional view with the dimensions of various parts and their relationship to one another. The essential features of the furnace are the inert argon atmosphere, the water-cooled copper crucible, and the water-cooled tungsten elec- trode. The melting crucible is formed by spinning 0.064-in. annealed copper sheet. A groove for an O-ring seal is spun into the flange of the crucible. A fiber gasket between the crucible flange and the water-cooled brass cover provides electrical insulation. The brass cover is fitted with a sight glass, an opening for the water-cooled electrode, and a tube through which the material is charged. Direct current is used for melting, with the positive electrical terminal connected to the water jacket and the negative terminal to the electrode. A typical heat is made in the new furnace as follows: Approximately, 0.20 lb of titanium under 2 mesh per in. and the alloy addition, if any is to be used, are placed in the bottom of the crucible. The cover is clamped on the crucible so that the O-rings make a tight seal. The remainder of the charge is placed in a glass bottle, and this is connected by a rubber hose to the charging tube of the furnace. The crucible and the charge are evacuated with a mechanical pump to a pressure below 50 mm of mercury, or less if desired, and held at this reduced pressure for 5 min. Hot water is circulated through the jacket during the evacuation period to assist in outgassing the crucible. Following the evacuation, tank argon of 99.92+ pct purity is flushed through the crucible for 5 min and then adjusted to give a positive pressure of 1 to 2 psi. During subsequent operation, an argon pressure regulator introduces only enough argon to compensate for the small leakage which occurs through a mercury trap. Re-evacuation and reflushing the melting chamber with argon produced a negligible reduction in contamination. Two 550-amp generators, connected in parallel, constitute the power source. Normally, about 800 amp are used for melting alloys which are not extremely refractory. The generators are set for 90 v open circuit and 200 amp. The arc is struck and the electrode is withdrawn to produce an arc of 23 to 26 v. This voltage is maintained while the electrode tip is moved slowly around a circle 1 in. smaller than the diameter of the ingot. The current

Jan 1, 1951

By J. Humphrey

Introduction The weight of a Mining Truck can be affected by field modifications, the selection of items like tires, rims or even the conditions in which it operates. Truck performance and the compliance with a number of ISO standards, e.g. braking, steering and ROPS are dependent on truck weight. It is critical that truck owners understand the impact of changes in weight1. What makes this even more difficult for owners to evaluate is that there is no standard terminology or definitions for Mining Truck weights. This paper discusses and defines weight terminology, how it applies to performance and standards and the impact on the application of Mining Trucks.

Jan 1, 2007

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for the expensive large-scale tests that are currently being used. A radiant-panel apparatus was used to determine the materials’ relevant thermal characteristics: time to ignition, critical heat flux for ignition, heat of gasification, and mass-loss rate. Three thermal parameters, TRP, TP1 and TP4, were derived from the data, then developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with the thermal and ignition hazards of similar materials reported in the literature and support this approach as a simpler one for quantifying these combustible hazards. Resumen ¦ El objetivo de este estudio fue el desarrollo de un método a escala de laboratorio con el fin de clasificar los peligros de ignición y fuego de materiales comúnmente usados en minería subterránea y la eliminación las pruebas costosas y a gran escala que se realizan actualmente. Se usó un aparato de panel radiante con el fin de determinar las características térmicas relevantes de los materiales: tiempo de ignición, flujo de calor crítico para ignición, calor de gasificación y tasa de pérdida de masa. Se derivaron tres parámetros térmicos de los datos: TRP, TP1 y TP4, luego fueron desarrollados y subsecuentemente usados para clasificar los peligros combinados de ignición y fuego de materiales combustibles, de bajo riesgo a alto riesgo. Los resultados tuvieron una comparación favorable con los riesgo/peligro térmicos y de ignición de materiales similares reportados en la literatura y apoyan este enfoque como uno más simple para la cuantificación de estos riesgos combustibles"

Jan 1, 2015

By Peter Joralemon

I want to limit my remarks to epigenetic ore deposits, but do not necessarily subscribe to the classic theories of hydrothermal ore deposition. I will consider an epigenetic deposit as a primary deposit in which the economic minerals have been introduced subsequent to the formation of the enclosing rock, regardless of the source. Past ore discoveries have been made to a great extent by prospecting techniques that have remained relatively constant over the last many decades. In many cases the discoveries have been enlarged or enhanced with the use of technical tools such as geophysics, but theoretical geology, which should serve as a foundation for exploration, has shown little progress of practical importance since the turn of the century.

Jan 1, 1967

By R. S. Fowkes

The Bureau of Mines constructed a fully automated pilot plant facility to study the hydraulic transportation of solids through a lock hopper feeder system. An equation for the energy requirements to transport coarse solids hydraulically proved applicable to this system. Optimum velocities were obtained for limestone, mine refuse, and bituminous coal. The experimental data, calculations, and graphs show the effect of velocity, specific gravity, and solids concentration on head loss and power requirements. Other data were obtained and evaluated to determine the effect of particle size on head loss. Results also are given for (a) tests using friction reducing polymers; (b) tests using seven test sections of steel alloy pipe to determine their wear characteristics; (c) tests to determine spatial segregation of moving particles; and (d) tests to determine the effect of shape, size, and specific gravity on particle velocity in a horizontal pipeline. The lock hopper feeder system was found practical for continuous hydraulic transportation of the material types and size ranges tested.

Jan 1, 1969

By Azin Zangooi, Cesar Gomez, James Finch

Frother concentration is a variable which significantly affects the flotation performance by decreasing bubble size and helping froth stabilization. Variations in frother concentration, which mostly go unnoticed in industrial operations, may affect these functions. Some factors that can cause variations include the fact that frothers are normally dosed based on feed tonnage and not solution concentration, unstable frother delivery, incomplete dissolution for low solubility frothers, addition of frother-free wash water, remnant frother in recycle waters and frother partitioning to the froth. A colorimetric technique developed for determining frother concentration on site makes it possible to detect the occurrence of these problems and to establish their magnitude, allowing conditions to be adjusted to reduce frother concentration variations. By sampling and analysis, frother distribution throughout a circuit can be established, referred to as ‘frother distribution mapping’. Experiences at several concentrators processing sulphide ores are used to illustrate time restrictions for sample analysis, and to demonstrate temporal and spatial frother concentration changes as a consequence of variations in the grinding stage, recycled waters containing frother, and frother partitioning.

Jan 1, 2014

By W. R. Ernst

A method for the removal of nickel and vanadium contaminants from spent HDS catalysts involves pretreating the catalyst with H2S followed by the extraction of the metals with an acidic solution of ferric ion. The ferric ion solution alone removes significant amounts of active ingredients cobalt and molybdenum; however, after pretreating the catalyst with H2S, the extraction becomes more selective for the removal of Ni and V.

Jan 1, 1986

By R Hartner

Digital optical microscopy (DOM) and automated SEM-based (ASEM) mineralogy systems (MLA, QEMSCAN) have experienced significant developments within the last decade. However these developments have been independent from each other and the two mineralogical techniques have so far not yet been integrated to combine the strengths and technical benefits of both analytical platforms. This detailed comprehensive mineralogical information is critical support for geometallurgy.Major hardware and software advances in DOM in the last few years have provided important new capabilities with potential applications to automated mineralogy. These technological advances have been largely driven by sectors outside mining (eg medical pathology) and have not yet been widely adopted within the minerals industry. The advent of DOM offers significantly more automated mineralogy capabilities than traditional expert-mineralogist driven optical microscopy. This is based on advances in automated image acquisition, high resolution cameras for digital imaging, imaging of large areas through mosaic options, integration of multiple layers and application of advanced image analysis techniques.Ongoing research involves combining the outputs of DOM and ASEM-based microscopy to create new capabilities for integrated microscopy based on development of advanced cross-platform image fusion and data integration between DOM and ASEM (exploiting the benefits of both analytical platforms). This requires non-linear image registration and transfer of mineralogical identification from ASEM to DOM systems using sophisticated image manipulation and data analysis software.Examples will be given of image fusion and data registration for a range of different ore types. Image fusion techniques are demonstrated using a porphyry copper deposit sample where sulfides and precious metals are classified using the MLA and gangue mineralogy obtained from DOM images. Data integration enables creation of a library containing optical property variability information for minerals identified by the MLA; thus reducing the reliance on skilled mineral identification by supplementing human interpretation

Sep 5, 2011

By Dan Urich

This paper covers the construction and operation of the Grate-Kiln system at the Humboldt Mine. The mine concentrator and pellet plant are located approximately 14 miles West of Ishpeming, Michigan, on the Marquette iron Range. Production of pellets began in mid-July, 1960.

Jan 1, 1962

By H. V. Fairbanks

It is estimated that millions of tons of coal fines are unsaleable each year due to difficulty of drying them economically with conventional mechanical dewatering and thermal drying equipment. The difficulty is due to the fact that coal of small particle size presents a large surface area with polar groups which have a great affinity for water. In order to remove this water thermally, a high temperature is necessary which oxidizes the surface of the coal. This substantially reduces the heating value of the coal. If drying could be satisfactorily carried out at a lower temperature, much more of the heating value of the coal fines could be retained. It was conjectured that acoustic energy applied during the drying process might prove to be of value since acoustic energy has the property of producing cavitation at a liquid-solid interface when the intensity is sufficiently great. This cavitation process produces water at room temperature which can be carried away from the solid surface by a flow of relatively cool air. Hence, moisture removal is made possible at a lower temperature.

Jan 1, 1966

By Walter Miller

The remarkable strides which have been made in recent years in the art of petroleum refining are not fully apparent until we attempt to compare the scientific status of the industry today with the basic conditions existing a decade or so ago. The spotlight has played so strongly on the development of cracking that many of the wonderful steps brought about in other departments have crept upon us unawares. A number of causes have contributed to this highly accelerated rate of progress. Constant effort by both companies and individuals to obtain the honors and prizes rewarding new discoveries has played its usual important part in our industry as in others. Competition has applied its continuous pressure on the refiner to reduce costs and losses and increase the proportionate yields of the higher-valued fractions. Advances in the engineering professions and growth in chemistry and allied sciences have contributed much. But there are other factors which deserve particular mention. The rapid development of the internal combustion engine, with the rigorous quality requirements and large quantity consumption of both fuel and lubricants has been a tremendous influence in adding impetus to natural progress. The teaching of petroleum principles and practices in many of our best universities and technical schools, and the calling into the industry of ever greater numbers of scientifically trained men to supplement the efforts of the practically trained operators, as well as to apply at close hand the fundamentals of science as a life work, has had and is having an incalculable influence. Important Improvements Let us consider briefly some of the most important improvements: First, distillation, which constitutes the greatest single phase of refinery operations, even with cracking excluded; that phase of distillation being handled as an individual subject in this symposium. Today we are distilling crude oil and redistilling by-products at a rate very much faster than was possible with the lesser knowledge of the art which we possessed

Jan 1, 1927

By A. Perry Thompson

Discussion of the paper of A. PERRY THOMPSON, presented at the San Francisco meeting, September, 1915, and printed 'in Bulletin No. 100, April, 1915, pp. 645 to 677. ARTHUR S. EAKLE, Berkeley, Cal.-At the old Morning Star mine in Alpine County, where large masses of enargite were found some years ago, I looked particularly for evidences of replacement of pyrite by the enargite. While I have not made a particular study of any of the specimens, I judge that the pyrite and enargite were precipitated together. They were both primarily in those rocks. Of course, by using Mr. Graton's method of determination we might possibly find a situation somewhat different, but I should say that the enargite is not replacing the pyrite, but was simply precipitated at the same time. The bodies occurred there within 50 ft. of the surface, so it is probably not a case of secondary enrichment. H. W. TURNER, San Francisco, Cal.-In the case where secondary chalcocite shows a crystalline structure and cleavage lines, what is the evidence of the secondary nature of it? C. F. TOLMAN, Stanford University, Cal.-You can find practically all the evidences we have discovered in the microscopic study of ores. You can find all stages in the process of replacement of earlier minerals, especially bornite, by chalcocite, from a stage, in which the process has but just started with only occasional fragments of chalcocite set in bornite, to a stage where remnants of bornite are set in chalcocite. The replacement may take place along the cleavage lines or along the crystallographic directions of the earlier mineral, or it may take place irregularly. In one type of replacement you may find in one spot a few cross-cutting veins, and in another spot the latter may be so enlarged that there remain only a few individual specks of the replaced mineral.

Jan 12, 1915