Search Documents

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By J Beniscelli

Some words to honour Pedro:Pedro was among the few persons with a very high level in geology modelling, resource and reserve estimation, geometallurgy development, sampling theory applications and a deep understanding of the mining industry needs. He had brilliant ideas about new developments on economic geology. He was always looking at the long-term and proposed challenging questions a decade in advance on their solution.The fundamental aim of geometallurgy is to add economic value to the mining of mine resources by timely providing information and knowledge about the relevant metallurgical variables represented by their space models. In this manner, geometallurgy allows obtaining the optimal design of a project, mitigating processing risks, optimising and supporting production plans and identifying and assessing mining business opportunities.This paper describes the conceptual framework and geometallurgical definitions and some of Codelco’s experience during the last 15 years.

Sep 5, 2011

CONCLUSIONS: Our experience, where we attempt to remove a continuous face with a seam more than six and one-half feet in thickness, has been rather disastrous. We have been able to open up faces and retreat for a distance of 75 to 100 feet in this particular character of coal, but after the supporting timbers have been removed for the second or third time we have found that the roof has a tendency to ride over the props and break off at the face of the coal support. However, where our coal is below six and one-half feet in thickness we have had very good success in handling the roof and breaking it off systematically with our break line of props, which are usually from 12 to 15 feet from the face of the coal. Our practice in to set props at about two-foot intervals in each direction and remove two sets of props, at the same time two additional sets are placed along the coal face. At all times we are very insistent that all props be removed from the gob and that entire coal be taken out so that it is possible for the roof to break freely and all come down, not having any supporting pillars in the gob. The conclusion of our experiments to date is that if all the supports beyond the breaking line of props are taken out as the long face retreats and the closer the breaking line of props is kept to the face the better the results will be. We have never felt it safe to have less than four rows of props to protect the machinery and men working along the coal face. We feel that the time element as to the rapidity with which these faces are advanced or retreated, is of vast importance, but to date have not had an opportunity or experience enough to reach any conclusion as to what time element is proper here with us. We feel that the crushing strength of the overlying strata will govern this to a large extent, and as ours varies considerably, it is going to he very difficult for us to reach a definite conclusion. My opinion is, that conditions may be such that rather than have a short face and retreat rapidly, it will be found that a longer facewith a slower retreat will work out better. Such a condition might give the overlying strata time to settle. The caving of roof or of control of this caving, with us, is quite closely associated with the ventilation. We find that the places where the strata overlying the coal are composed of shale, that the effect of the air on this is of very great importance. It is our endeavor, at all times, not only to remove obnoxious gases, but to keep a current of fresh air moving along the face and, of course, a portion of this travels over the gob and comes in contact with the roof and overlying strata. This, we find, helps materially in keeping the roof on the move. As it is our practice to keep water for sprinkling purposes at all places, we also use this water to keep the roof wet back in the gob. The effect of water on the shale is to cause it to disintegrate quite rapidly. MR. HOLMAN (Concluding): If there are any questions about this, I will be glad to answer them. I have some prints and also some pictures of the scraper loader and the shaking conveyors (distributes.) PRESIDENT MOSES: We wish to thank you, Mr. Holman, and also wish that you would thank Mr. Dupont for his paper. Are there any discussions? Do you wish to ask Mr. Holman any questions? (No response.) PRESIDENT MOSES: Mr. Holman, I would like to ask you how you take the photographs; were they taken by flashlight, or were globes used, or how were they taken, in a gaseous mine? MR. HOLMAN: Our mines being gaseous, we do not use the ordinary flashlight for taking underground photographs, but we have had considerable success, I think, with underground pictures by means of electric lights. We use 250 watt globes. We have six of these rigged up with tin reflectors, 18 inches in diameter, on standards, and we carry two or three hundred feet of wire connected with these six lights, and they can be turned on in the room where we take the photograph, by means of this extra wire. We set the kodak up and arrange the picture and take a long time-exposure. We usually take an

Jan 1, 1926

By N. S. Dalal, B. Jafari, F. H. Y. Green, M. Petersen, V. Vallyathan

"Stable coal radicals (SCRs) were detected by electron spin resonance (ESR) spectroscopy in the lung tissue of autopsied coal miners. The SCR concentrations were measured in the lung tissues from 98 coal miners with and without (a) coal workers' pneumoconiosis (CWP), (b) cancer, and (c) a history of cigarette smoking. Concentrations of SCRs were also determined in the lungs of nonminer controls. The SCR concentration was related to longer mining tenure, CWP disease severity, lung cancer, and cigarette smoking. The mean concentration of SCRs in the lung tissues of miners with 30 ± 1.4 y of coal mining exposure was 5.3 ± 1.3 x 10"" spins/g versus controls who had a nondetec¬table level (< 10 15 spins/g). An increase in disease severity was accompanied by a progressive increase in SCR concentration. A SCR concentration of 4.8 ± 0.7 x 10"" spins/g was found for simple CWP (with moderate coal macules) versus 7.8 ± 4.6 spins/g lung tissue for complicated CWP (with progressive massive fibrosis). Significantly higher (i.e., 10 x 10"") concentrations of SCR in the coal miners' lung tissues were associated with an exposure history in the anthracite regions of northeastern Pennsylvania. These results in¬dicate a possible role for SCRs in the disease process. Furthermore, ESR appears to be an adequate methodology for the quantitation of coal dust retained in the lung and for distinguishing exposures to anthracite and/or bituminous coal.THE PREVALENCE AND SEVERITY of coal workers' pneumoconiosis (CWP) differ markedly between geographic locations, mines, and coal fields irrespective of comparable levels of exposure to coal mine dust These differences cannot be fully explained by the presence of silica and other minerals in the coal mine dust.' Rank of coal is also an important factor in the pathogenesis of CWP. Equally important is that the prevalence of CWP decreases from east to west in the United States,' and South Wales miners develop more severe CWP than miners in Scotland.' However, there are conflicting reports that cast uncertainty on the influence of rank of coal in the development of CWP."" These problems are complicated but will be solved as new technology emerges and as more is learned about the disease process."

Mar 1, 1992

By J. Raath, A. J. Fischmann, C. Spagnuol, E. D. Brooks

This paper demonstrates the use of Clean TeQ Water’s ATA® rapid dewatering technology as an alternative approach to the tailings paddock buttressing method which is currently being implemented. ATA® is a three-component system where the tailings stream is separated into fines and coarse fractions utilising a hydro-cyclone. The results from the pilot demonstrated that the use of ATA® offers significant advantages, including higher homogeneity in the buttress, higher permeability, and faster settling rates.

Apr 8, 2026

[Adams, Leonard E.819 Newhouse Bldg., Salt Lake City, Utah Adams, V. H422 East San Miguel. Colorado Springs, Colo. Allen, Earl W.2636 So. Gilpin St., Denver 10, Colo. Allen, Thomas State Coal Mine Inspector, State Office Bldg., Denver, Colo. Ambler, J. B P. O. Box 591, Denver, Colo. Apperson, A. B 394 Elm St., Denver 7, Colo. Arnold, G. O Phelps-Dodge Co., Dawson, New Mexico Audin, Abel Somerset, Colorado Audis, Clement, Jr. Paonia, Colorado]

Jan 1, 1948

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively.INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By A. Lubinski, C. R. Stewart, K. A. Blenkarn

Storage porosity has been considered one of the important pore geometry characteristics of heterogeneous-porosity limestones. Storage pores are only containers for fluids, in contrast to flow channel pores which both contain fluids and provide continuity for fluid flow. The concept of another geometry characteristic, "poro-striction", is presented as a second pertinent variable in describing limestone pore space. In simple terms, poro-striction is a measure of the flow resistance between storage and flow channel pores. Alternating-flow core-testing theory provides flow relationships which can be used to divide the pore space of heterogeneous-porosity media into flow channel and storage pores and to measure the "porostriction" of the latter. Experimental application of this theory to naturally occurring heterogeneous limestones shows that "porostriction" and the ratio of storage to flow channel pores can be estimated. Porostriction and porosity ratio are microscopic characteristics which should influence oil-recovery efficiencies during certain types of displacement processes. A knowledge of pore geometry should be valuable in designing or selecting the most effective oil-recovery process for heterogeneous limestones containing storage porosity. INTRODUCTION The primary and secondary recovery of oil from limestone (carbonate) reservoirs has been and will continue to be a major source of the world&apos;s supply of petroleum. Oil recovery from this type of formation is strongly influenced by the size, shape and arrangement of the pore spaces which hold the formation fluids. Therefore, it is expected that better knowledge of pore geometry would lead to design of more effective recovery processes. The concept of storage and flow channel pores has been presented as an important characteristic of limestone porosity.1 In this concept, storage pores are only containers for fluids, whereas flow channel pores are those pores which both contain and transmit the fluids. The work reported herein involves the concept of an additional pore characteristic called "porostriction". This characteristic can be visualized as the flow resistance between the storage and flow channel pores. This resistance is an important pore geometry characteristic because it determines how easily gas and oil can replenish fluids removed from the flow channel pores. Fatt and co-workers at the U. of California have studied the effect of storage porosity and a factor similar to porostriction on transient-flow response of models of porous media during a pressure build-up or drawdown test.55 These models consisted of porous sandstone cores with artificially simulated storage pores. It is the purpose of this paper to describe tests which permit the storage porosity and porostriction of actual reservoir core samples to be estimated. The tests used for this purpose involved not transient tests but, rather, an alternating-flow technique in which pressure and flow are varied according to a sine-wave relationship. This technique may offer advantages over transient methods. THE POROSTRICTION CONCEPT Before discussing alternating-flow (A.F.) tests in core samples, it is necessary to define the porostriction parameter. For this purpose attention is focused upon an elemental volume v representative of a porous medium having both flow channel pores and restricted-access storage pores. For such an elemental volume, it is considered that the storage porosity is combined to form a single pore and that the access into the storage porosity may be represented by a single capillary tube connecting the single pore to the flow channels of the elemental volume. Let the radius of the capillary tube be designated as Rc and its length as L,. When fluid flows into or out of the pore, the following equation (Poiseuille&apos;s law) relates flow rate q to pressure drop p, and the physical characteristics of the tube and the fluid of viscosity jx.

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By G. Winkel

"Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today. In addition to protecting people, safety has been shown to make good business sense in any industry.The road to safety improvement is built on establishing a culture of safety that forms the basis for how work gets done in a company. Most importantly, an effective safety culture is built on the full engagement and participation of workers and leaders alike, who share in a vision for safe work performance where “no one gets hurt” and “everyone is a leader in safety.”Let’s learn together on how we can make a safety culture happen. The resulting bias for safety will ultimately save lives, and fulfills our moral objective to strive for safety excellence. IntroductionWe have the good fortune of living in democratic countries where freedom and the value of human life are key beliefs. These beliefs translate into the moral obligations and laws that we value and uphold in our society and life today.A minesite or workplace is simply a necessary part of our society where people earn a living. It is a place where our moral obligations and laws equally apply, a place where human life is of ultimate importance and value. In the early years of industry, this value has not always been evident. Take this description of a tragic accident reported in a coal mine on December 8, 1879:“Oliver Thompson, shaftman, aged 35— While taking wooden partitions out of a ventilation shaft, he fell off the work platform a distance of 100 yards, there did not appear to be anything unusual to account for this accident.”"

Jan 1, 2004

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

By N. S. Tanious

The need to provide better mine roof support and control in longwall tailgate entries prompted the Bureau of mines to search for a replacement product for wood cribs. Their search isolated steel-fiber-reinforced concrete (SFC) as the most effective replacement. Through successful laboratory and underground mine tests, handmade SFC cribs proved to be a viable and more effective roof support system. However, to ensure wider usage, U. S. Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Company in order to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated during this program to determine their compressive strength and post failure characteristics. After considerable testing and adjusting of various concrete mixtures, a final formulation for the SFC crib blocks was selected. That formulation permitted the construction of SFC cribs possessing a nominal crib strength of 3200 psi (22.1 x 106 Pa) and a nominal modulus of elasticity of 1.0 x 106 psi (6894.76 x 106 Pa). These SFC cribs can support from 3.5 to 14.5 times as much load as a wood crib, depending on the size of the wood crib being replaced. Both laboratory and limited mine tests, conducted by U. S. Steel Mining Co. have shown the SFC crib to be an economical and effective means of roof control.

Jan 1, 1984

By George Kellock

In presenting this paper for discussion at the Western Annual Meeting to be held in Edmonton, it is with the idea of creating a full and general discussion by the mining men in the Province as to the best way to eliminate, or at least hold down to a minimum, the dangerous coal-dust which is made in mining pitching seams in our Alberta mines by the chute method. Also, an alternative method is outlined, whereby the percentage of lump-coal mined can be increased, and the mining costs reduced-although the paper does not go into any detailed consideration of costs. The general trend of mining practice and lay-outs is at present towards mechanization, and the results being accomplished by the substitution of machines for manual labour are fully justifying the changes. In the technical mining journals, there are published from time to time papers dealing with a variety of methods of mining, which are descriptions of actual operations, and a great deal of interesting and valuable data is given as to the comparative values of the different methods, insofar as the percentage of grades of coal produced, the cost of production, etc., are concerned; but the mechanical methods described in these papers are nearly always suitable only for flat seams, or seams with a very low inclination.

Jan 1, 1929

By M. Clair Smith

The Sweetwater, Castro, Trinidad, New London, and Hilltop chromite properties are situated within an area 8 miles long and 1 mile wide between San Luis Obispo city and Morro Creek, San Luis Obiso County, Calif. Development work at this group of mines was a part of a long-range project by the Bureau of Mines to develop strategic mineral reserves in the United States in accordance with the Strategic Minerals Act of 1939. The junior author of this report participated in the preliminary examinations made in 1941 of the chromite deposits that later in the same year were the subject of more intensive investigation under the immediate supervision of the senior author. The ore occurs in lenses and kidneys in masses of dunite contained in large poridetite areas. Production has boon in the form of lump ore and concentrates from disseminated ore. Work by the Bureau of Miner included surveying, mapping, trenching, sampling, and assaying. It is summarized separately in the text under the name of each mine investigated. The report gives a brief history of the district, describer the concentrating plant of the Castro Associates, and gives detailed results on sampling and assays at the various proportion.

Jan 1, 1951

By Ed Revoort, Robert Schippers

In Rotterdam in the Netherlands the project ‘De Zalmhaven’ is being developed. The project consists of the realization of houses, parking facilities, two residential towers of 70 m and a residential high rise of 215 m. An artist impression for the project is given in figure 1. For the high rise a new development in the use of large diameter, drilled piles with a steel casing has been successfully utilized. In this article the installation method of 65 m long steel drilled piles in two consecutive sections is presented. The settlements for the building (and the influence on its surroundings) have been analyzed in detail using 3D Finite Element calculations, which will also be discussed. Finally there is focus on the results of settlement measurements carried out during construction in relation to the settlement prognosis.

May 1, 2022

By Sir Robert Hadfield

(New York Meeting, February, 1913.) THE Hadfield method of producing sound steel ingots has been the subject of a paper 1 read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make possible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying additional beat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By-one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molted condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 4, 1913

By V. Ross

"The Upper Group 2 (UG2) reef in the Bushveld Complex in South Africa hosts an estimated 40% of the world’s Platinum Group Metal (PGM) resources. The processing of this ore via flotation poses two particular challenges: limiting the levels of chromite in the concentrate to reduce downstream smelting problems, and enhancing the recovery of ultrafine (typically -10 micron), liberated PGMs. Conventional ways of suppressing the entrained chromite, such as froth washing, is not effective in PGM operations, which are dominated by mechanical cells. The recovery of fine particles is hampered by low collision efficiencies with air bubbles, as well as oxidised surface layers especially in tailings operations. This paper documents the results of laboratory tests on a run-of-mine PGM UG2 ore, investigating the application of a pneumo-mechanical column (PMC) and its effect on PGM flotation and its selectivity with regard to chromite. A key feature of the device is the stage-wise release of aerated slurry from an agitated downcomer, thus creating conditions where the superficial velocity profiles of air and slurry change axially within the separation zone. This aids segregation of the silicates and chromite-rich fractions in the separation zone, concentrating the latter towards the bottom of the column and minimising its entrainment into the concentrate. Comparison of the performance of the PMC to that of mechanical laboratory cells under equivalent operating conditions showed improved PGM flotation kinetics and recovery. This was accompanied by a decrease in gangue recovery compared to the mechanical cells by more than 40%, thus doubling the final rougher concentrate grade from 50 to 100 g/t. Significantly, whilst the overall Cr2O3 recovery was reduced by more than 60%, the selectivity (PGM recovery vs Cr2O3 grade in the concentrate) was doubled.INTRODUCTIONThe Bushveld complex in the northern part of South Africa hosts the world’s largest reserves of Platinum Group Metals (PGMs), representing approximately 40% of the total PGE. It is characterised by three main PGM bearing reefs, namely Merensky, Upper Group 2 (UG2) and the Platreef. The Merensky and Platreef are dominated by silicates in the form of pyroxenites, and carry economically recoverable amounts of copper and nickel, in the form of chalcopyrite and pentlandite. The UG2 on the other hand is a chromitite ore with chromite as (ideally, FeO.Cr2O3) the most abundant gangue, often constituting more than 70% by mass with a PGM grade of around 4.5 g/t. Other key gangue minerals are pyroxene, feldspar and talc. The PGEs occur in a wide variety of minerals, with platinum and palladium sulphides typically accounting for about half of the total. Base metal sulphides such as chalcopyrite, pentlandite and pyrrhotite occur in only very minor amounts, accounting mostly for less than 0.1% by mass."

Jan 1, 2018

By Gaby Steinbach

A novel synthesis is described for the preparation of supported gold catalysts for low-temperature CO oxidation. The novel route is a variation of the inverse co-precipitation method and requires amphoteric metal hydroxides, with zinc and aluminium hydroxides chosen. Catalysts were prepared by inverse co-precipitation (ICPa) and by the novel route (ICPb) and tested for CO oxidation at 60ºC. Preliminary results showed the novel route to be superior to ICPa; the catalysts prepared by ICPb showed higher catalytic activities. The effect on catalytic activity of parameters such as pH, calcination temperature, washing of precursor and calcined catalysts and ageing was investigated. A preparation pH of 9 and a Zn to Al mass ratio of 3 proved to be optimal. It was possible to remove residual chloride by washing thereby enhancing catalyst performance. Ageing and Mg citrate addition were also shown to improve catalyst performance. Characterization of the catalysts revealed that better activities were obtained when the support was more crystalline and had a higher surface area. The presence of carbonate-containing species in the support decreased catalytic activity. 197Au Mössbauer Spectroscopy revealed the presence of Au3+ when catalysts were heat-treated at temperatures of 200ºC and below. Catalysts calcined at 400º had 75% of the gold present as Au0, with the remaining gold present as Au3+.

Oct 1, 2003

By Fred H. Lightner

Mergers and acquisitions (M&A) within the mining industry are becoming frequent events. Large companies and small companies alike are jumping on the bandwagon of merger mania. The results of these mergers have significant impacts on the employees of the involved companies. Comments, observations, and specific examples of the &apos;peop1e"aspect of mergers are presented in an attempt to answer the question "will it be business as usual?" My answer is a simple NO. This paper attempts to provide support for my conclusion. The reader should recognize that the comments, observations, and specific examples mentioned in this paper are subjective and reflect the experience and prejudice of the author.

Jan 1, 2001

By M. Sephton

Slat-band chains, currently manufactured from Type 430 ferritic stainless steel, are used as conveyors in various industries. A process to strengthen these chains?with the aim of prolonging the lifetime of the conveyors?was developed recently. The process entails heat treating the cold-worked chain at 475°C,strengthening the material by precipitation of the Cr-rich phase a? at relatively long periods of aging. In the present work, it was found that increasing the interstitial content by solution heat treatments (at 880°C or 930°C) prior to cold rolling and aging, causes an increase in strength at shorter aging times as a result of the precipitation of chromium-rich carbides and nitrides. The solution treatments can introduce martensite into the microstructure if carried out at a sufficiently high temperature. This, along with the deformation caused by cold work, also increases the strength. Corrosion resistance is not affected by the treatments, but ductility is lowered. However, calculated critical crack lengths indicate that solution treatment at a temperature below the Ac1allows for a larger critical flaw size, and that the lifetime of the chains will probably be determined by fatigue. Although the duration of the service of the chains are reportedly controlled by wear, with these treatments the tensile strength of the material is increased to within acceptable limits for conveyor chains. The tensile strength is an indication of the wear or abrasion resistance of a material. It is expected that after the treatments, the wear resistance will be improved, but since embrittlement occurs, the fatigue resistance is lowered. It is concluded that the preferred processing route for the chains would be solution treatment at 880°C, fast quenching to trap the interstitial atoms, cold rolling and then aging at 475°C for 8 minutes.

Jan 1, 1997