Search Documents

By C. S. Herzig

In the Engineering and Mining Journal of Jan. 27, 1900, there appeared an article by Fred T. Greene, describing a method of measuring stopes by the use of strings, a clinometer and a tape. In the early part of 1899 I had occasion to use a somewhat similar method, for the purpose of accurately ascertaining the volume of a very irregular drift connecting two mines. This drift was an important factor in a lawsuit for $150,000, in which it was necessary to determine accurately the volume originally occupied by the material extracted from the drift. While it is unnecessary to give all details of the controversy, some explanation of the conditions is required for a clear understanding of the following description. This drift was started by the a E." Co. from its workings, in about 7 ft. of ore, and headed toward the " G " property, the plan being to extract all the ore between foot- and hanging-walls, but to take out nothing but ore. As the " G." workings were approached; the ore-body became very irregular and much thinner. It was, however, very closely followed, and where the drift broke through into the " G." workings, the hole was only 11 inches high by 14 inches wide, or just about the size of a man-hole in a boiler.. Thus, this connection-drift tapered sharply; and the very irregular foot-wall sloped toward the " G." workings, and entered them at a place where the stope was only about 3 ft. high, and the ground had already commenced to cave. It may be added that the ore-body was a nearly flat deposit of lead carbonate in limestone, the ore and gangue being quite soft. I was called upon by the " G." people to make the survey

Jan 1, 1901

By H. Maleki

As mining continues toward deeper reserves in thick western US coal fields, the control of mining induced-seismicity has become a priority in many operations in Utah, Colorado, and Wyoming. Gradual floor heave, common in many coal mines, has historically not been a safety issue. However recent occurrences of sudden floor heave accompanied with seismicity in a few deep mines have fueled this investigation. The focus is to identify and study the mechanisms resulting in sudden heaving of the mine floor in western U.S. deep coal mines through analytical calculations and back analyses of an actual event in a cooperative mine. Based on review of available data in three mines, underground observations and back analyses of an actual event, the authors have identified the following contributing factors (1) presence of stiff stratigraphic units and thick seams mined at depths exceeding 1000-ft (2) presence of geological discontinuities reducing the in-situ strength of the coal with calculated factor of safety near 1 for the mine floor (3) mining approaching areas of higher than normal stress gradient associated with previous mining or structural anomalies or surface topographic highs and (4) an additional source of energy triggering sudden failure such as periodic caving or slip along geological discontinuities. Preliminary examination of seismic data for the actual event in the cooperative mine and underground observations excluded fault slip at the mining horizon as the triggering mechanism but highlighted the significance of weak, anisotropic strata conditions near the intersection of two faults.

Jan 1, 2009

By H. F. Anderson

The Palabora Mining Company Ltd. is probably best known for its production of copper since 1965. The success of the PMC mine lies in the outstanding technical and highly organized efficiencies applied to the massive mining, transportation, and treatment operations necessary to produce profitable copper. We are not however going to discuss the well-known copper operation but the extremely successful recovery and marketing of Baddeleyite by the PMC group. Let us first review the extraction process at the Heavy Minerals Plant. Non-magnetic ground ore from the copper magnetic separators is processed in the Heavy Minerals Plant for the extraction of the "heavy minerals" uranium and zirconia (Baddeleyite). Thorium is also present as a potentially recoverable mineral. The content of the minerals in the feed is probably the lowest in the world to be treated commercially. Minerals are separated from the waste ore by a gravity separation process in which the high density minerals segregate preferentially in a waterborne system.

Jan 1, 1985

While ring-blasting techniques offer substantial benefits, there are intrinsic problems that are exacerbated when large blocks of ore are mined in attempts to improve the production economics. These problems relate to both the convergence of holes around the ring drive and the charging of up-holes. The size and shape of the ore block concerned should be carefully considered so that good drilling, patterns can be achieved. The hole diameters chosen, both affect and are affected by the size of the ore block. The explosive selected depends on the hole diameter and together with the diameter, determines the nominal drilling pattern. Ring-drilling patterns are best derived through the use of computer software together with engineering judgement. The loading of explosive is necessarily high, and charging patterns require careful thought if overcharging is to he minimised and adequate energy is to be available at all parts of the ore block. Initiation systems are critical to the blasting results, but sub-optimal systems must be adopted if collar priming is practised. In view of all these factors, idealised guidelines can be given for ring design, but it should be recognised that developments in technology may in time change some of these parameters.

Jan 1, 2000

By CYRIL W., William Campbell, Henry M. Howe

THIS paper gives the results of an investigation of the behavior of the argentiferous cobalt-nickel arsenides of Temiskaming, Ontario, in roasting, made in the metallurgical laboratories of the School of Mines, of Columbia University in the City of New York. The ore was kindly given by the owners of the La Rose and Trethewey properties at Cobalt, Ontario, and Mr. E. J. Hall, Tutor in Assaying in Columbia University, has helped us much. I. OBJECT OF THE INVESTIGATION. The object of the investigation was to learn:- 1. The temperature at which the arsenic is most rapidly expelled; 2. The thoroughness with which it is expelled by prolonged roasting at this temperature; 3. The effect of adding charcoal (a) near the end of the roast and (b) at the beginning of the roast. II. NATURE OF THE ORE. The important ores mined in the Temiskaming deposits are native silver-with small amounts of dyscrasite (Ag6 Sb), argentite (Ag2S), pyrargyrite (Ag3SbS3)-smaltite (CoAs2), chloanthite (NiAs2) and niccolite (NiAs). Mispickel (FeAsS) and cobaltite (CoAsS) also occur in smaller quantities. The average composition of the ore shipped from this district for the first six months of 1905 -was: silver, from 4.1 to 4.8 per cent.; cobalt, from 6.9 to 8.2 per cent ; nickel, from 3 to 4.7 per cent ; and arsenic, from 30.9 to 34.6 per cent. The ore which we treated consists chiefly of smaltite ; In our laboratory-work

Jan 1, 1907

By J. W. Wolfe

The Benedict-Webb-Rmbin equation of state was used in digital computer programs to make rapid determinations of natural gas equilibrium phase compositions. Mixture components were the nine hydrocarbons, methane through heptane. Comparative tests were made with data from field separators, plant exchangers and literature sources. For most tests made, the B-W-R equations predrcted component K-vallles, mixture enthalpies and phase aensities within tile accuracy of available correlations for rune-component mixtures: significant deviations were noted when mixtures contained components heavier than heptune. INTRODUCTION Rapid, accurate methods for calculating the properties of hydrocarbon mixtures are needed for predicting the behavior of natural gas processes. For example, because of the common use of two-phase separation methods in gas proccssing, calculations must be made for the density and composition of equilibrium vapor and liquid phases. In addition, predictions must often be made for the temperature and pressure changes associated with the flow of single- and two-phase natural gas fluids through heat exchangers, chokes and turbines. The complex nature of non-ideal mixtures makes rigorous calculations for these natural gas properties difficult and time-consuming. Natural gas properties have conventionally been determined with generalized data correlations. These correlations, such as the K-values presented in the NGAA Equilibrium Ratio Data Book, are usually based on some average property of the mixture and have proven to give satisfactory estimates for the properties of most oil and gas systems. Digital computers, however, have not only increased the utility of these correlations, but also have made practical the use of equations of state for calculating the properties of natural gases. Potentially, if basic pure component data are available, all the desired thermodynamic properties of mixtures can be derived from a single equation of state describing the mixture. Currently. the best equation of state for describing the behavior of pure, light hydrocarbons over single-and two-phase regions, both below and above critical pressure, is that of Benedict. Webb and Rubin.' The equation contains eight constants which are determined by empirically fitting the equation to pure-component PVT data. Benedict and his co-workers presented the clevelopment of their equation as early as 1940.2 The B-W-R equation is a modification of the Beattie-Bridgeman equation of state and gives better PVT predictions than the Beattie equation at densities above the critical density. Benedict et al. made the equation applicable to mixtures by relating the mixture constants to composition and the constants for pure compounds. These authors, in a serics of articles in 1951,' showed the accuracy of the B-W-R equation when applied to light hydrocarbons and their simple mixtures, and demonstrated the equation's utility for making vapor-liquid equilibria calculations. Since its inception, the B-W-R equation has been the subject of many papers. Numerous additions and modifications have been proposed,'-',"'-':' the purpose of most being to improve the equation's ability to predict PVT properties of specific mixture systems. In 1959, Opfell, Pings and Sage summarized much of the work on the B-W-R equation in their book on equations of state." Since natural gases are primarily mixtures of light hydrocarbons, the B-W-R equation is a natural choice for an equation of state to compute both phase equilibria and thermodynamic properties of natural gases. Consequent-

Jan 1, 1967

By Kevin Andrews, SETAREH GHAYCHI AFROUZ

Ground control analysis and groundwater inflow assessments for underground coal mines require in-depth field investigations including, but not limited to, geological and geotechnical core logging, downhole geophysical logging, laboratory rock strength testing, and packer (Lugeon) testing. Field and laboratory data collection are time consuming and expensive, and an initial understanding of the expected trends among various geotechnical and hydrogeological parameters can assist with the planning and optimization of geotechnical characterization studies and grouting plans. In this study, a comprehensive database is analyzed, comprised of important rock mass characteristics (hydraulic conductivity, rock quality designation (RQD), and lithology) for coal-bearing rocks in the Central Appalachian Basin. Statistical analysis of the data is completed to establish an enhanced understanding of geotechnical and hydrogeological conditions expected to be encountered as underground coal mining passes near and beneath streams and rivers. The results of the study provide valuable reference material for the coal mining industry for completion of shaft installations, mine stream crossings, environmental assessments, and grouting and mine dewatering designs.

Jul 1, 2023

By Zhonglin Ye, Yifeng Shi

"This paper has outlined forms of Au & Ag losses in copper smelting process and methods for increasing Au & Ag recovery, analyzed factors influencing Au & Ag recovery in copper converting process, presented Au & Ag behavior in copper electrorefining process, and reviewed effect of current density/electrolyte circulation rate during electrolysis and surface finish of cathode on Au & Ag losses. Measures and research direction for decreasing Au & Ag losses in electrolysis have also been introduced. Based on Au & Ag behavior in copper electrorefining process and previous studies by others, new approach for increasing Au & Ag recovery in copper smelter has been discussed. And brief comparison has made between continued multiplication method and equilibrium method application in the case of calculation of Au & Ag recovery in copper smelter.IntroductionAs gold and silver are the major by-products from copper smelting process, efficient Au & Ag recovery has become one of the key approaches for copper producers to increase economic efficiency. With similar physicochemical properties, Cu, Au and Ag belong to the first subgroup of elements in the same periodic table. Au and Ag will be enriched into Cu phase firstly when both matte-slag phase and copper-matte phase appear in copper smelting process. However, great changes have taken place in Au & Ag proportions into individual phase due to changes of physicochemical conditions in each smelting process. Metallurgists at home and abroad have carried out a great deal of pilot plant tests and laboratory tests in order to increase Au & Ag the former Soviet Union with regard to Au & Ag losses in copper smelting process in the 1970s and 1980s, and he proposed solutions to increase Au & Ag recovery in copper metallurgical plants. As more than 20 years passed, Jingchun Lu's paper, Discussion on Increasing Au & Ag Recovery in Copper Smelting System, remains as a literature of the most comprehensive study. Based on Jingchun Lu's literature, the authors of this paper discussed new approaches to increase Au & Ag recovery in copper metallurgical plants with combination of many researches done by other researchers for over 20 years."

Jan 1, 2013

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry's side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries' own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

By Euclid P. Worden

In 1977, an article in World Mining1 reported a total of 2726 rotary blasthole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher. Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to reducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is best measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, there are five factors which affect the rate of penetration. They are: (1) bit selection, (2) weight on the bit, (3) rotary speed, (4) hole cleaning, and (5) formation properties. Of these factors, all but one may be controlled by the operator. Looking at any one in detail may reveal possible improvements in the system. One of these factors -- proper hole cleaning - will be discussed in this paper. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in redrilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole. In an in-depth study of the cleaning of large diameter holes, Allen2 reports that horizontal air velocities of 38.10 m/s are necessary to prevent the saltation of drilled cuttings on the bottom of the hole. The exact flow pattern on the bottom of the hole, however, is not generally known. The air leaves the bit through the jet nozzles and the mouths of the cones, but where it goes from there is uncertain. This problem should be investigated by the bit manufacturers because they can best utilize the results of such an investigation to provide a more effective product. Some work has been initiated in this area and competition will probably increase its intensity. Bailing velocity is the best criteria to measure the cleaning of the hole, including the bottom, and is the factor on which efforts toward improvement must be concentrated. The first consideration is "What should the bailing velocity really be?" In drilling deep holes for oil and gas, 15.24 m/s is the generally accepted figure. In blasthole drilling, the figures of 25.40 m/s for average rock to 35.56 m/s for iron ore were first mentioned by Capp3 in 1962. The recommendations are the same to this day. A number of questions could be asked in regard to the apparent disparity between these two sets of figures. Various investigators have derived formulas which support one or another of these criteria. A thesis on the subject was written by Alexander4 who derived a formula based on research which resulted in velocities in the lower end of the ranges quoted previously. He set out to compare this figure to laboratory tests and his tests indicated that the velocities given by the derived formula appeared to be high.1 Perhaps the best reason that the 25.40 to 35.56 m/s range has been used, is that these velocities seem to work. Below the accepted figures, low bit life and slow penetration rates occur. Above these figures, increasing amounts of abrasive wear on the drill pipe and stabilizers seem to appear. There is a fallacy to this entire approach, however. The entire velocity calculation is made using nominal bit and pipe sizes and compressor deliveries with no compensation made for losses in the system. Perhaps an examination of some of the things that are not presently considered could lead to some practical improvements in the operation.

Jan 1, 1980

By Benjamin Smith Lyman

THE importance of topography to geology is so commonly underrated as to deserve to be pointed out again and again. The relation of topography to the different branches of geology may be seen best by a glance at them all. Geology is well understood to consist of the observation of facts about rocks as materials of the earth (geognosy), and the explanation of those facts (geognosy). The facts to observe are : I. GEOMETRICAL, as (1) structure, including the dip and strike at different points, the size, shape, and position of basins and saddles; (2) vertical section, that is, the thickness of rock groups and of their parts ; (3) horizontal or geographical position. 11. PHYSICAL, such as texture, whether sedimentary or crystalline ; and, if crystalline, whether granitic, porphyritic, amygdaloidal, globular, or concretionary ; whether compact or granular; coarse or fine; pervious or impervious; hard or soft; firm or tender; with cleavage or without ; massive or thin ; the microscopic structure ; also whether magnetic or not ; soluble or insoluble ; fusible or infusible ; and the constituent minerals. 111. CHEMICAL that is, the composition of the rocks and of their minerals and their affinities. IV. PALAENTOLOGICAL, as what kind of fossils are in the rocks,

Andy H. Vassiliou – Introduction Ladies and gentlemen,.good evening and welcome to the Paul F. Kerr Memorial Symposium dinner. I believe we are all here to honor the memory of a great teacher and advisor, and a true friend -- Professor Kerr, or Dr. Kerr, or to most of us who were his students, "Pappy" Kerr. Most of us who attended the Paul F. Kerr Memorial Symposium earlier today at the New York Hilton had the opportunity to read, or listen to, or discuss scientific papers presented in honor of Dr. Kerr. In addition, all of the speakers had the opportunity to reminisce about their association with Dr. Kerr, who was credited as having contributed substantially to their graduate education and the development of their careers. Dr. Kerr's two daughters -- Ruth and Nancy -- who attended the Symposium at the Hilton are also here with us tonight. I think we should keep tonight's festivities on an informal basis since we are all old friends or former students of Dr. Kerr. Some of us may want to say a few words about our experiences at the time we were students at Columbia, and hopefully include some anecdotes relating to Professor Kerr. I would like to invite everyone to do so, but first we have arranged for two of us to be the lead speakers, whom I will introduce in a few moments.

Jan 1, 1985

By M. G. Benz, J. F. Elliott

A new type of solution calorimeter has been constructed to measure heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction at temperatures above 1000°C. With it, measurements hove been made of the partial molar heats of mixing joy tin in the Cu-Sn system from 0 to 13 at. pet Sn at 1127°C and fir nickel in the Cu-Ni system from 0 to 9 at, pet Ni at 1200°C. The integral molar heat of mixing for the Cu-Sn system is strongly negative with a calculated minimum value corresponding to the composition Cu3Sn. The integrnl molar heat of mixing for the Czi-Ni system is slightly positive at these temperatures. These integral molar values have been measured with a probable error less than 30 cal per g-atom at an atom fraction of nickel or tin equal to 0.1. The estimated probable error for the Cu-Sn system is approximately 450 cal for a measured heat of solution of approximately 9000 cal. For the Cu-Ni system it is approximately 700 cal for a measured heat of' solution of approximately 60 cal. A new type of heat of solution calorimeter was designed and constructed to provide a more accurate experimental method for determining heat effects at high temperatures, (T > 1000°C). With it, partial molar heats of mixing, enthalpy increments, heats of fusion, and heats of formation and reaction for metal systems can be measured directly. Previously it has been necessary to rely upon the use of the dropping calorimeter or the van't Hoff equation applied to equilibrium data for this information. For the most part equilibrium data are scarce and difficult to obtain in many cases, and it has been necessary to rely upon the "method of mixtures" for the desired enthalpy measurements. An earlier study1 provides a prototype for this work. The "method of mixtures" as outlined by K. K. kelley,2 "consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a calorimeter operating at or near room temperature.'' In this manner the change in the total heat content (enthalpy) of the substance between the temperature of the furnace and that of the calorimeter is determined. In order to determine high-temperature heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction, it is necessary to take the difference between two such measurements, one before and one after the occurrence of the enthalpy change being studied. The desired enthalpy change is then the small difference between two large numbers. Small errors in the large numbers are included as large errors in this small difference. It is this difficulty that must be avoided for accurate measurement of the desired functions. The procedure with the new solution calorimeter consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a solution calorimeter operating in the temperature range of 1000o to 1200°C. Measurements in the range of 1200" to 1600°C are planned for the future. By selection of the composition and

Jan 1, 1964

By R. A. Cummings

Certain roof shales in coal mines deteriorate upon exposure to the atmosphere, causing difficulties in the mining operations and adding to the cost. This report presents the results of both field investigations, in a West Virginia mine, and laboratory studies on the effects of atmospheric moisture on roof shales. Based on these observations a conceptual procedure is presented on how shale deterioration might be predicted during exploration, and guidelines are given as to how air tempering or conditioning chambers may be designed to reduce moisture effects. Recommendations for further studies are included. An annotated bibliography of the literature constitutes the second volume.

Jan 1, 1981

By Kimio Ilagaki

The distribution ratios of Ag, Pb, As, Sb and Bi for the Cu2S-FeS or Ni3S2-FeS matte I FeOx-SiOl, FeOx-Si02-CaO or FeOx-CaO slag equilibration in a MgO crucible were determined experimentally at 1523 ~1573K under controlled partial pressures of S2 and 02 at given PS02 of 10.1,50.7 and 101.3 kPa(O.I, 0.5 and I atm), and the observed dependency of distribution ratio on the matte grade, S02 pressure and slag basicity were analyzed on the basis of thermodynamics.

Jan 1, 2003

Equilibrium in the reaction H2(g) + [%0] (in liquid copper) = H2O (g) was investigated at temperatures between 1200 -and 1350°C with p(H2Oj/p(H2) ratios between 1 to 15. A semi-microbalance was used for direct measurement of dissolved oxygen in molten copper. Oxygen was found to obey Henry's law under the experimental conditions used. The standard free-energy change for the above reaction is given by Equation 1where 1 weight per cent solution is the standard state for dissolved oxygen.For the dissolution of oxygen in copper according to 1/2 O2(g) = [%0] (liq. Cu), the standard free energychange is given byEquation 2.

Jan 1, 1973

A New Ingersoll-Rand Turbo Blower The Ingersoll-Rand Co. has added to its Turbo Compressors and Blowers a low-pressure machine t o handle volumes from 3,000 to 35,000 cu. ft. per minute at from 1-2 ½ lb. These are particularly adapted to such service as foundry cupola blowing, atomizing oil for oil burners, supplying blast to heating and annealing furnaces of various kinds, blowing air for water-gas generators, pneumatic conveying and ventilating. They are of the single stage, double flow type and are furnished either electric motor, steam turbine or water wheel driven.

Jan 6, 1916

By P Audet, D R. Mulligan, D Doley

This analysis attempts to reconcile existing ecological theories, rehabilitation planning goals and implementation constraints in the form of a rehabilitation paradigm that considers potential and pragmatic ecosystem transformation pathways. The framework prioritises multiple developmental scenarios for post-disturbed landscapes within a continuum of ecological outcomes. A feature of the framework is that ænovelÆ ecosystems and agro-ecosystems, having a range of commercial and societal values, are valid outcomes spanning the conceptual divide between the ecological functions of under-rehabilitated versus re-instated ænaturalÆ landscapes, especially in a changing environment. Landscape suitability analyses are considered to be fundamental to the incorporation of regional landscape and climate in the implementation of land rehabilitation and management strategies. Altogether, the paradigm could facilitate the identification of widely pertinent rehabilitation goals having direct implications at the regional scale of restoration ecology and acceptance of the need for ongoing commitment to the management of disturbed environments.CITATION:Audet, P, Doley, D and Mulligan, D R, 2012. Can ænovelÆ ecosystems offer suitable rehabilitation alternatives for post-mined landscapes?, in Proceedings Life-of-Mine 2012 , pp 135-142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Kwong. Kyei-Sing

Gasification is a process that converts a carbon feedstock into synthesis gas (CO+H2). Slagging gasifiers operate at high temperature and pressure and in a corrosive-wear environment from the slag. Cr2O3-based refractory linings are used to protect the steel vessel that comprises the gasifier from the aggressive gasification environment. Increasing service life of the gasifier is one of the keys for wide spread development of this technology. In support of the goals, research on the gasifier atmosphere, the slag chemistry, the interaction of Cr2O3 refractory with different feedstock mixtures (e.g., coal and petcoke) were characterized by post mortem analysis of bricks from service in gasifiers and thermodynamics simulation of the environment. Examples demonstrating how thermodynamic calculations can explain the post mortem results and make predictions of material interactions will be given. Attention is placed on the possibility of Cr+6 in different feedstock mixtures and operating conditions.

Jan 1, 2010

By Robert B Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943