Search Documents

By Robert B. Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

By AIME AIME

THE United Electric Coal Companies, operating large strip mines at various points in Illinois, pioneered in developing and perfecting the strip method of mining coal by use of large shovels and drag-lines. Coal stripping was first started on the properties owned by this company near Danville, Ill., in 1885. The first mechanical' excavating machine used for the purpose was really a dredge minus the hull, which had been purchased from the Marion Steam Shovel Co. It was erected on a wood frame supported by wheels and was referred to as a dry-land dredge or stripping machine. Wood was used throughout in the construction of this primitive excavator, even for the boom which was 50 ft. long. A single-cylinder vertical steam engine furnished power to hoist the %-yd. dipper arid swing the boom. 400 cu. yd. of overburden moved in a day was a great record.

Jan 1, 1936

By John Gross

"Introduction.Southern Illinois and Kentucky are credited with approximately 90% of the fluorspar production of the United States. A small amount of high-grade acid, spar is obtained from the ore by band sorting; the greater part, however, is recovered by jigs and tables as gravel spar containing approximately 85% calcium fluoride. In the jigging and tabling operations, galena is recovered, and enough silica and calcite are removed to raise the calcium fluoride content of the gravel spar to 85%. However, the removal of silica and calcite results in a large loss of spar. With increasing depth in the mines, zinc sulphide, sphalerite, is encountered in increasing quantity and the removal of this has become a serious problem. While the sphalerite can be fairly well removed from the spar by present milling methods, a marketable zinc concentrate can not be made. The experiments described below were made on fluorspar ore from Southern Illinois, by the mining experiment station of the U. S. Bureau of Mines, at Rolla, Mo., in cooperation with the Missouri School of Mines and Metallurgy.The ore tested contained. 7.3% lead, 27.9% zinc, 35.7% calcium fluoride, 9.5% silica and 4.7%. calcite.Tests and Results. In some preliminary tests it was noticed that a portion of the finely crushed ore adhered strongly to the sample pans, and upon investigation it was found that the adhering material was practically clean spar. By utilizing this property of adhesion 46.8% of the spar was recovered as a product containing 98.3% calcium fluoride. This suggested the possibility of using electrostatic separation."

Jul 1, 1921

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

By Frank R. Field, Randolph E. Kirchain, Elisa Alonso

"There are a number of environmental incentives for increasing recycling, including the reduction of waste, energy and resource use. Recycling can also be advantageous for manufacturing firms in both the short and long term. Secondary material can substitute for primary material, potentially dampening primary material price increases and reducing the pressure for greater primary extraction. This paper examines the potential for and dynamics of recycling for the case of platinum using a dynamic, behavioral simulation model of the primary and secondary markets. Since the secondary supply of platinum depends on a supply chain separate from primary extraction, recycling can diversify the risks of primary supply instabilities. Over time, recycling can cut primary consumption, reduce overall costs to firms, and possibly reduce the impact of price fluctuations upon firms.IntroductionThe benefits of recycling, from the perspective of the environment, are many, and the environmental benefits of increased recycling are considered a step towards increased sustainability [1, 2]. Life cycle assessments indicate that obtaining materials from secondary sources generally requires less energy and has fewer environmental impacts than extraction and refining of primary materials [3]. Analyses of materials flows show that, in addition to landfill volume reduction, recycling reduces primary material consumption, affecting long term materials scarcity [4, 5].The benefits of recycling are not limited to the environmental. Firms can benefit from the lower energy costs of recycling, especially that of metals whose primary extraction and refining are particularly energy-intensive (e.g., aluminum). The routine participation by firms in secondary materials markets (e.g., www.recycle.net) shows that this advantage has not gone unnoticed.Recycling can also benefit firms whose costs can be significantly affected by changes in material prices resulting from material shortages and material scarcity, with potentially permanent effects upon firms [6-8]. This paper focuses on the impact of recycling in the face of platinum scarcity for supply chain downstream firms."

Jan 1, 2008

By M. Elmadagli

Wear mechanisms of two commercial aluminum alloys, namely a spray formed and extruded Al-25%Si alloy, and a sand cast A390 alloy (18.5 %Si) that are known to be successful in cylinder bore technology were studied to have a better understanding of the requirements for wear resistant aluminum alloy design. From durability point of view these alloys are known to be successful for engine bore applications. It is interesting to compare the wear mechanisms in these alloys because they have significantly different silicon content and microstructures, and were produced using different techniques. The wear tests were done using a block-on-ring configuration, in controlled air atmospheres (5 % relative humidity). In spite of the differences in silicon content and microstructure, the wear mechanisms were similar and consisted of formation and destruction of hard tribolayers that are either formed by either mechanical or chemical interactions on contact surfaces. The differences in the wear rates between the two alloys arose from the differences in the hardness of the worn surfaces, and the alloy's ability to sustain the tribolayers on the worn surfaces.

Jan 1, 2004

By M. M. C. Lima, L. C. S. Solimani, M. A. Quintela

Galvanized steel scrap is recycled to B OF converters where zinc escapes from the bath and is captured by the gas control system, appearing in BOF sludge. As BOF sludge contain high iron content, it could be recycled, but due to its zinc content, it is disposed in landfills. In this study techniques were evaluated for zinc layer removal from scrap by sulfuric acid leaching. The effects of coating weight, temperature, time and sulfuric acid concentration were evaluated for three different galvanized scrap. The results showed that the behavior of each galvanized scrap was different. Nevertheless zinc removal efficiency was more than 80% with low dissolved iron in the leached solution.

Jan 1, 2011

By Charles A. Bankston, John C. Rowley, Robert J. Hanold, Joseph W. Neudecker

The basic concepts and processes of soil and rock melting as applied to excavation technology are reviewed. The electrically heated, small diameter prototype penetrator development sequence is presented. Emphasis is placed on the different methods of handling the fluid rock and soil melts and their significance in providing new solutions in hole support and debris handling problems. The refractory materials requirements, penetrator life and electrical heater technology are presented. Consolidating penetrators, which form stable glass-lined holes in low density rocks and soils, require no debris removal and will find applications in horizontal holes for utilities, cables, and pipeline installations. Extruding penetrators are being developed to make holes in dense, hard rocks. Melt is conditioned into a variety of debris forms, i.e., glass rods, pellets or rock wool, selected to match appropriate debris handling systems. Unique use in drilling into very hot rock or magma for geothermal exploration or production wells is projected. Some of the results of laboratory and field tests of these devices are compared with theoretically derived operating performance. Coring-consolidating penetrators for geological sampling in alluvium are projected to larger diameter self-propelled and guided coring devices for prospecting along proposed tunnel alignments. Application to the melting of annular shafts for pipeline support piles in difficult conditions such as permafrost has been scoped. Conceptual design studies of large diameter tunneling equipment have indicated the system contributions and economic aspects of rock melting relative to material comminution, wall and roof support and materials handling.

Jan 1, 1974

By Kostas Fytas, Sebastien Perreault

This paper presents EOLAVAL, an integrated mine ventilation design software. In its new expanded version it is a user friendly and fully interactive computer package. The features of the new version are a graphics interface fully compatible with Autocad files, an integrated database of fan characteristics and the optional use of the thermodynamic approach in carrying out network simulations. This software can be used in underground mine ventilation planning: mine ventilation network analysis and simulation, economic design of airways, auxiliary ventilation design, calculation of a mine air heating plant, and evaluation of the natural ventilation and pressure losses in a mine shaft. This paper presents a case study illustrating the use of the computer package in mine ventilation design.

Jan 1, 2002

The Epithermal and Mesothermal Gold Prospectivity modelling projects carried out by Crown Minerals provided explorers in New Zealand with a new compilation of historical exploration data combined with new geological information from the GNS QMap 1:250,000 scale mapping project. These data were used to produce predictive mineral potential maps for gold mineralisation in New Zealand. The aim of these projects, to stimulate mineral exploration and investment in exploration, has been successful with eight new companies acquiring new tenement positions and committing significant exploration expenditure to exploring in New Zealand in the coming years. The projects were done at a national scale and consequently not all exploration data were compiled into the prospectivity models. Several of the new companies recognised the value of the prospectivity modelling work and committed exploration funds to continue the modelling process. They recognised a need to compile the remaining data and run the models again to allow detailed exploration targeting. Detailed data compilations including digitising historic exploration stream sediment sample, rock chip sample, soil sample and drilling data has been completed. New models have been completed in Otago for mesothermal gold mineralisation and in the Coromandel and Northland for epithermal gold. The new models have been compared with the original regional scale models and used to target prospect scale exploration. This work has allowed exploration models for epithermal and mesothermal mineralisation in New Zealand to be refined. More importantly this work has identified significant areas with potential to host gold mineralisation with little or no systematic geochemical data including soil sampling or drilling. Exploration work programs have been designed to acquire these missing data and exploration funds have now been committed to test the areas highlighted by the prospectivity modelling. In summary, the Epithermal and Mesothermal Gold Prospectivity modelling work has successfully attracted new investment and ideas to the exploration scene in New Zealand. The projects had an estimated cost of NA$250 000 and will in the next two years, just through exploration expenditure, attract more than NZ$10 M in investment. If a mine is discovered the return on investment will be considerably greater.

Jan 1, 2004

By Albert F. J. Bordeaux

(Cleveland Meeting, October, 1912.) THE immediate vicinity of the sea-shore, affording special facility for the exportation of ores, makes it possible to work certain mines in the Vladivostok district, which, in more remote places of Siberia, would remain unproductive. Outside of the city of Vladivostok the population is small and the country is very little prospected. Additional discoveries of valuable deposits like the large body of calamine which has recently been opened in the neighborhood of earlier worked lead-silver ores, in the Tetiuhe valley, are still in the field of possibilities. For many years gold alone was produced, in part from the coastal rivers and in part from a quartz-vein on Askold island near Vladivostok. But the production is diminishing, and prospectors are looking for other rivers in the interior, such as the tributaries of the Ussuri. These rivers are now more accessible than formerly, due to the slow but gradual development, of colonization by the Russian peasants. The few natives of the country, called Orodjones, are of the Chinese race. They resemble the North American Indian and are hardy fur-hunters. They have given some attention to placers and have already shown good specimens of gold-dust from the rivers Iman, Bikin, Noto, etc. Coal-mining was begun in the Vladivostok region more than 20 years ago, but in a somewhat irregular way. The industry is not as yet important and the best coal-seams are badly prospected, or ire even neglected. Copper, lead, and iron exist in several places. The amounts give some encouragement to the anticipation that the discoveries will give rise to important metallurgical works. I here present a review of the various deposits, based upon such safe information as is in hand, when I have not drawn upon my personal observations. Fig. 1 is a snap of Eastern Siberia, showing the mineral deposits.

Oct 1, 1912

By E. F. Miller

The subject " Safe Timbering of Working Places in Mobile Loading" is one that requires an analytical study of the strata both above and below the coal seam as well as the characteristics of the coal seam itself. The projection or mining plan must be based on economic roof control in which the application of timber can be minimized without incurring cost increases in other phases of production. The several types of loading machines in common use today are not adaptable to the same projections or timbering systems. Consequently the type of equipment to be used must also be considered. For these reasons the writer does not believe that the problems of timbering in working places can be discussed without simultaneously considering economic production as well as the safety of men and the conservation of equipment. Prior to the introduction of loading machines as a substitute for the pick and shovel system of loading coal, the care and maintenance of the individual working places were generally the responsibility of the coal loaders who worked in them. Up to that time very few coal companies had developed and applied fixed and definite standards for timbering the working places in the mines they operated. It is common knowledge that mechanical loading of coal has had several false starts in the last twenty-five years and it is only in the last decade that it has developed to the stage at which we now find it. During this twenty-five year period the management of the more responsible companies have come to realize the tremendous importance of roof control in coal mining. From a safety viewpoint, the lack of roof control has been and still is responsible for more than a third of the industry's annual fatality experience. In recent years workmen's compensation and insurance rates have steadily increased while the profit margin has decreased almost to the point of elimination. From an economic operating viewpoint, the failure to properly control roof is quite often the most costly single phase of coal mining. Since the manufacturers of loading machine equipment have so improved their machines that normal care and maintenance can reduce to a minimum the time lost because of mechanical failure the production delays from other causes have assumed a far greater importance. Roof control in the broad sense and in the light of concentrated mining plans or projections that are adapted to mobile loading should be regarded as one of the major problems in the inseparable phases of production and safety of the workman and equipment at the working face. The subject of this paper cannot be treated properly unless what is said here is based upon the broad and fundamental problem of genera' roof control. The suc-cessful solution of a problem arising in any industry must have its origin in a complete analysis of the known facts or factors that pertain to it. The several illustrations

Jan 1, 1949

By T. M. Ruff

A GPS-based traffic awareness and collision avoidance system has been implemented at mines with long, narrow access roads to help avoid accidents involving two approaching vehicles or vehicles following too close. A simple display in the cab of each outfitted vehicle gives an indication of oncoming traffic and a voice announcement indicates the type of vehicle that is coming as far out as 300 meters. Advanced warning of approaching vehicles is increasing driver awareness, especially around blind corners and in adverse weather such as heavy fog, snow, or rain. Speeding alarms have also been implemented and are especially critical as a vehicle approaches reduced speed areas near single-lane bridges or tight curves. A description of the system, safety improvements seen since its introduction, and implementation challenges will be discussed.

Aug 1, 2013

By Lj. D. Andric

By the micronization-milling of the material, the size and the structure of its particles are changed and it comes to the increasing of the potential energy of the system as well as to the chem-ical activity of the material what is the result of an increased free surface and of the concentration of the grate defects, that is of the internal energy of the system. All these changes that are reached, show that new characteristics of treated materials are got by micronization process. Controlling the process of the micronization and by purpose directing of the new characteristics of the activated materials, we can have the positive effects and use them in more technologies. Talc is important nonmetallic mineral raw material that is widely used as either the basic raw material, or as filler. This has stimulated its technological investigation, as well as the investigation of its physical-chemical characteristics. In this paper are shown experimentally reached results of the physical-chemical characteristics of the talc during the process of the micronization in high energetic mill. In this paper, the optimum conditions of miconization of talc in high-energy-speed rotary mill and its influence micronization on a degree of Fe2O3recovery by hydrometallurgical methodes, are presented. The X-ray analysis of the obtained products showed that high quality talc with low content of can be obtained by these physical-chemical processes In this paper, the principles and application or fine and ultra-fine grinding high-energy attriton mill with small balls, enabling fast, efficient grinding, low energy consumption, short grinding time and easy handling will be described.

Jan 1, 2014

Universities have had a long history in the education of geology graduates, Analysis of this history reveals a record of success, as judged on a world basis. However there have been significant changes in the last 20 years that have impacted on the ability of universities to continue to provide their traditional style of geology education. These changes have increased in the last 10 years. In the teaching side, there has been a change in expectations. Additionally the increasing workload decreases the value of each academic to perform the tasks needed by the new education. In the area of research, the funds provided have continued to decline, in both real and absolute terms, and it is now necessary for universities to seek out funds to pay for their postgraduate research. Additionally, the universities have slipped into the error of what cahn only be termed "academic incest", and research student mobility has decreased to an undesirable level, stifling initiative and new ideas in a number of cases, The only solution is for Government monies to be "directed" - ie that the postgraduate student must leave his or her original university in order to receifve the research stipend/scholarship. On the government front, the government and its agencies have not adequately analysed and recognised the need for the redirection of education and research funds into the needy areas of science and technology, especially those that related to the minerals area.

Jan 1, 1986

By Paivi Suikkanen, Kari Hietala, Kaarlo Haavanlammi

"Processing of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of platinum group metals (PGM’s) and cobalt are key issues of the Nickel Smelting technologies. PGMs are typically found in association with each other, but also importantly with nickel and copper. A challenge of producing saleable concentrates at acceptable recovery degrees, an increasing focus on the sustainable use of metals and recent decreases in the value of nickel has increased the interest to find a reliable route from Cu-Ni-PGM bulk concentrates to product. According to studies, most efficient process for Ni-Cu-PGM concentrates is flash smelting using DON process20 years ago, in 1995, Outokumpu commenced at Harjavalta a new Nickel Flash Smelting technology based on the Direct Outotec Nickel (DON) Smelting Process. The DON process enables production of high-grade nickel matte with low Fe-content directly in the Flash Smelting Furnace (FSF) without subsequent converting. Metal values from the smelting slag are recovered in the Electric Furnace (EF) as iron containing Ni-matte. Matte refining is based on atmospheric pre-leaching and total pressure leaching. Nickel, cobalt and iron are leached leaving a leach residue containing small amount of gangue minerals and PGM’s. Iron is removed from the leach solution in and nickel will be recovered with standard methods. Overall > 95% metal recovery can be expected with low energy consumption and low environmental impact."

Jan 1, 2014

By D. N. Seidrnan

In the present note we present thermal-analysis data for the liquidus curve from 0 to 76 at. pct Se and for the selenium-rich monotectic reaction in the Pb-Se system. We have previously reported that no expey-imental eviderzce was found for a lead-rich monotectic reaction, at -860°C with a monotectic composition of -20.5 at. pct Se, as found by Nozato and Igaki.&apos; Our additional data substantiated this earlier finding and extended the composition range studied. The alloys were prepared from semiconductor -grade lead and selenium purchased from the American Smelting and Refining Co. Both elements were 99.999+ wt pct pure as determined by the supplier. The impurities for lead were Fe (1 ppm) and Cu & ppm) while for selenium the impurities were Cu (< 1 ppm), As (< 1 ppm), Te (1 ppm), and C1 (<1 ppm). The general procedures used for thermal analysis were those specified by the National Bureau of Standards. A Pt/Pt-10 pct Rh thermocouple calibrated against the freezing points of zinc and copper purchased from the National Bureau of Standards and antimony (99.985 pct pure) purchased from A. D. Mackay, New York, was used for all the thermal analysis. The thermocouple electromotive force was measured with a Rubicon Type B potentiometer used in conjunction with a galvanometer with a sensitivity of 0.5 pV (mm) -&apos;. The absolute accuracy of this thermal-analysis system was *0.5"C. One-hundred-gram alloys of the desired composition were sealed in quartz crucibles, with a central thermocouple well, at a pressure of less than 10"1 Torr. The alloys were initially heated well above the liquidus curve and shaken vigorously to insure homogeneity. Cooling curves were then taken by the direct method at cooling rates ranging from -0.5" to 1.5"C (min)-&apos;. The phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis is shown in Fig. l.* An extrapolation of the selenium-rich portion of the liquidus curve to the monotectic reaction isotherm (678.3"C) gave a value of 76.1 at. pct Se for the monotectic composition. A tabulation of all the thermal-analysis data is given in Table I. As we previously reported no experimental evidence was found Fig. l—The partial Pb-Se phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis. For the sake of clarity the points for the 49.00 and 49.16 at. pct Se alloys were not drawn on this phase diagram, see Table I. for the lead-rich monotectic reaction found by Nozato and Igaki.&apos; This result was further substantiated by the fact that none of twelve lead-rich alloys, see Table I, examined for this monotectic reaction exhibited a thermal arrest in the temperature range (849" to 863°C) cited by Nozato and Igaki for the lead-rich monotectic reaction. Hence, our results tend to support the earlier qualitative work of ~elabon&apos; and Friedrich and ~eroux" in the 0 to 50 at. pct portion of the phase diagram, though the selenium-rich monotectic composition and reaction isotherm temperature were in agreement with the approximate values (75 at. pct Se and 672" to 680°C) given by Nozato and ~~aki. &apos;

Jan 1, 1967

By S. Feuerstein, L. Rice

The effect of low pressures on the flow and fracture behavior of molybdenum is described. For poly crystalline samples, room-temperature tensile tests indicate greater ductility under 10 Torr than under intermediate pressures up to and including atmospheric pressure (760 Torr). In addition, tests conducted at 760 Torr under atmospheres of air, dry nitrogen, and purified argon exhibited no apparent difference in mechanical properties. Critical tests involving baking in situ as well as those involving single-crystal deformation further imply that the ductility effect is a pressure-dependent phenomenon related only to the fracture process. This dependency is discussed in terms of adsorption and diffusion contributions. THE effect of very low pressures on material properties has heretofore been presumed to be important only for substances possessing relatively high vapor pressures at ambient temperatures. Research has therefore been concentrated primarily on organic solids and liquids, and in some instances on metals such as zinc and cadmium. Most vacuum-effect studies&apos; on the mechanical behavior of metals have been performed under conditions of either cyclic loading or creep rupture at elevated temperatures, i.e., over extended time periods. These studies were not restricted to high vapor pressure materials but also encompassed such metals as gold, copper, and nickel. Very little concern, however, was placed upon the importance of a vacuum environment on the mechanical behavior of metals subjected to a simple unidirectional deformation at ambient temperatures. A tension test is generally of short duration as compared to a creep test, and at room temperature vacuum effects if any would be expected to be surface-limited. In early 1963, Kramer and podlaseck2 reported a change in the bulk flow behavior of aluminum single crystals during room-temperature tension tests. The deformations were performed under pressure conditions of 760 to 3.4 X 10-8 Torr and indicated for the first time a vacuum surface effect contributing to the bulk tensile behavior of metal specimens. As a consequence, an experimental program was initiated in this Laboratory to study the effects of ultrahigh-vacuum conditions on the mechanical behavior of metals. The results of a preliminary study on poly-crystalline molybdenum3 revealed, unlike Kramer&apos;s observations of changes in the stress-strain behavior, only an increased ductility under ultrahigh vacuum. Flow behaviors were nearly identical for all tests re- gardless of pressure. This paper presents comprehensive results obtained in this area of research. 1) EXPERIMENTAL PROCEDURE Three material categories were used in this study: sintered and are-cast polycrystalline molybdenum of nominal purity 99.93+ pct and single-pass electron-beam zone-refined molybdenum single crystals having a nominal purity level of 99.99+ pct. The interstitial levels (weight percent) as determined by the Materials Testing Laboratories, Division of Magnaflux Corp., were as follows: sintered molybdenum (C— 0.005, H—0.0004, O—0.015, N—0.008); and arc-cast molybdenum (C-0.0038, H-0.0003, O-0.015, N-0.023). Single-crystal molybdenum obtained from Materials Research Corp. had a typical interstitial analysis of C-0.0015, H-0.00007, O—0.00045, and N-0.0001. Tensile specimens having a 5 mm diam by 50.8 mm length were prepared from these materials. An average grain diameter of 0.059 mm was obtained for the sintered specimens following a 4-hr, 1600°C heat treatment. Grain sizes from 0.019 to 0.149 mm were obtained in the arc-cast specimens following heat treatments from 1100° to 1600°C for 1 hr. This series of specimens was used exclusively for the grain-size effect studies. All samples were electrolytically polished in 97 pct sulfuric acid solution prior to testing. Experiments were performed at room temperature in an ion-pumped ultrahigh-vacuum system positioned in an Instron tensile machine, Fig. 1. A constant strain rate of 4.2 x 10-4 sec-1 as derived from crosshead displacement was assumed for the deformations. Starting vacuums ranged from 2 to 0.5 X 10-10 Torr. These pressure measurements were made using corrected values4 of an NRC Redhead gage. Comparative readings were also made against a G.E. triggered dis-

Jan 1, 1967

By W. A. Tiller, J. P. McHugh

HE majority of liquidus and solidus surfaces in phase diagrams have been determined by the conventional cooling- and heating-curve techniques.&apos; These techniques have two main shortcomings: 1) the solidus may be in considerable error due to the difficulty involved in completely homogenizing the solid and 2) the determination of liquidus and solidus in more than a two-component system does not enable one to determine tie-lines connecting the specific equilibrium solid and liquid compositions. However, in a recent paper by one of the authors,&apos; a method was suggested whereby the liquidus and solidus surfaces plus tie-lines in an n-component system may be determined. This method utilizes a controlled solidification technique and assumes that interface equilibrium exists during freezing. The present work was undertaken with a twofold purpose; first, to determine the liquidus and solidus lines in the pseudo-binary system Bi2Te3-Bi2Se3 by heating- and cooling-curve techniques and, second, to determine the partition coefficients of Te and Se in the BizTe3-,Sex system by controlled solidifica- tion techniques. The two sets of results can be compared to test the accuracy of the controlled solidification method. EXPERIMENTAL I—The starting materials for this study were 997999 pct Bi, Te, and Se, obtained from the American Smelting and Refining Co. The compounds BizTe, and Bi2Se3 were each prepared by melting together stoichiometric amounts of the elements, followed by twelve zone-refining passes. This produced homogeneous bars of the compounds for use in the phase-diagram studies. The apparatus used to obtain heating and cooling curves is illustrated schematically in Fig. 1. The alloy samples were located in a graphite crucible placed in a stainless steel canister. The canister was supported in a heavily lagged pit furnace by a device which oscillated the canister about its vertical axis at a frequency of about 3 cycles per sec during heating and cooling-curve runs. The graphite crucible was designed to minimize the thermal coupling of the sample to the furnace. A thin graphite sleeve separated the alloy sample from the stainless steel tube that housed the thermo-

Jan 1, 1960