Search Documents

By B. Krysa, A. Mitsui, T. L. Koehler

The presence of arsenic, even at trace levels, in copper processing leads to the risk of arsine gas where reducing conditions exist that can reduce any soluble arsenic present to its minus 3 valance state and generate hydrogen gas from the solutions. This risk is understood to be significant within the industry, particularly in the case of liberator cells where copper concentrations in solution are drawn down to remove the copper and impurities from the bleed stream. However, there are numerous other potential areas where the arsine gas risk exists including contact between active metal such as iron, zinc or aluminum and arsenic bearing solutions in pyrometallurgical dust treatment, refining and acid plant operations. In turn this breaks down to different mitigating strategies dependent on the risk scenarios considered; for example, how this risk interacts with Change Management, Confined Space Entry or Contractor Training. The ISO 45001 is an emerging standard meant to improve employee safety, reduce workplace risks and create safer working conditions all over the world. The paper shows a case study of how a framework consistent with the tenets of ISO 45001 has been used to provide a consistent assessment of this risk for a wide variety of copper operations and the expectations of how this may be used to effectively improve the effectiveness of barriers against future incidents. INTRODUCTION Arsine gas (AsH3), first identified in 1775, is a highly poisonous, colorless, non-irritating gas with a mild garlic odor that is heavier than air. Arsine gas is generated when reducing conditions are generated in the presence of hydrogen ions and arsenic compounds. Present permissible occupational exposure limit as defined by Occupational Safety and Health Administration (OSHA) as an 8-hour time-weighted average is ppm (0.2 mg/m3). Further increasing the risk, conventional respiratory protection utilizing half or full masks with gas filtering cartridges provide minimal protection against arsine. In copper processing plants, the risk of arsine generation is well understood in liberator cells, which are part of the electrolysis process. In this process, solutions containing copper are reduced in copper concentration removing not only the copper, but also arsenic, antimony and bismuth. The residual solution can be bled to control impurity build-up in the refinery. In this process, if the copper concentration is reduced to the point where As3- can form, arsine gas is generated via reaction with hydrogen ions generated during the plating process. The copper concentration at which arsine gas is generated depends on copper concentration at the cathode surface, the temperature and the acidity. As a result, there is always a risk of arsine gas generation in the liberator cell. Process measures to minimize or mitigate arsine evolution are tight control on final copper concentration, warm temperatures, fresh feed distribution and internal acid recirculation rates. Operator exposure protection measures are hooding, ventilation, arsine detection systems, restricted personnel access, automated shutdown controls and pre-defined evacuation plans.

Jan 1, 2019

By Zhiqian Zhang, Chao Wu, Chao Li, Hongxu Li, Yu Chen, Xiangxin Hao

"In this paper, the life cycle assessment models for automobile lightweight materials including high-strength steel, aluminum alloy and magnesium alloy are developed by Gabi software. The evaluation models and evaluation indicators such as acidification effects, rich eutrophication effect, ozone layer depletion effects, global warming, resource consumption and formation of ozone potential were taken into account. It is shown that the effects of acidification and ozone formation are mainly derived from the run phase of high-strength steel and they have strong environmental impact load. While considering the entire life cycle with materials production phase and resource consumption, the aluminum and magnesium alloy appe art o have large r environmental load than high-strength steel. Base d on the evaluation, some optimization tips are proposed.IntroductionAs the increasing of car ownership, automobile has its two sides. One which is the convenient, efficient and fast traffic vehicle; the other is aggravating energy consumption, emissions and environmental pollution. The car industry faces heavy pressure with energy saving, safety and environmental protection. Nowadays, the main study ways for automotive energy-saving and environmental protection are power system improvement, alternative energy sources and technologies. For limitation of technique, development cycle and market share, the development of car is little progress at this stage and the application has been restricted. And another important way is the lightweight of vehicle. Usually there are three ways to get the lightweight automobile body structure, automobile body structure optimized design, using advanced body manufacturing technology, development and application of lightweight high strength body material.The life cycle assessment (LCA)[1lis commonly used to evaluate environmental factors and potential environmental impacts of products and services. As an environmental management tool of product-oriented, it becomes increasingly popular in industry. In this study, the concept of LCA and GaBi software was used to develop models for the three automotive lightweight materials, evaluate the environmental impact and make horizontal and vertical contrast by choosing variety of evaluation systems and indexes."

Jan 1, 2013

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

By K L. Temel, W P. Player

The underlying message of this paper is that investment in prospecting, exploration and mining in New Zealand is welcomed. The Government's policy with respect to Crown owned minerals is for continuing investment in prospecting, exploration and mining which is in accordance with good exploration or mining practice. To encourage continued investment requires a business-friendly environment. Government policies and initiatives to enhance the business environment for the minerals and coal exploration and mining industries are discussed in this paper. As well, new initiatives under consideration, which have the purpose of enhancing the investment environment, are discussed.

Jan 1, 1997

By P. Davey Wheeler

San Francisco meeting, September, 1915) IN an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in. thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. 1.) Fig. 2 is a photograph of the end of the punching, showing the .hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of, radiographing metals. In order to gain some preliminary data, several pieces of ½ -in(12.5mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter 1 1/4 in. = 6.3 mm 2 1/8 in. = 3.1 mm. 3 1/16 in. = 1.6 mm. 4 1/32 in. = 0.8 mm. 5 1/64 in. = 0.4 mm.

Jan 8, 1915

By A Kleinitz, J Halilovic, K Trappitt

Mine operators use grade control to determine the destination of each block of material in the mine. In polymetallic mines, grades are best expressed in dollars: the Net Smelter Return, NSR, per tonne. To estimate NSRs, geologists working on grade control develop models for each geometallurgical domain in the mine. These models may incorporate observations on the mineralogy and grain sizes of the material being examined. The site’s mill operators contribute to the models by providing geologists with statistical analyses that relate assay results and mineralogical compositions to metallurgical parameters, such as the rates of recovery of each economic metal to each of the concentrates produced, and the compositions of those concentrates. The team responsible for sales and marketing of the site’s products contributes to the NSR models by providing details of the costs of shipping concentrates to smelters and refineries; and by providing figures that are specified in the smelter contracts, such as the payability of the metals in each concentrate and the fees charged by the smelter. The mill operators also provide, for the NSR models, equations to estimate the rates of recovery of deleterious materials to each concentrate. Deleterious materials comprise mostly halogens and amphoteric elements, both of which reduce the efficiency of smelters. Furthermore, deleterious materials such as antimony and arsenic may be poisonous to people and to the environment. The sales and marketing team provide specifics of the penalties that smelters impose upon deleterious materials. These penalties may reduce NSRs by tens of percent, possibly to levels below the cut-off grade. Thus, in the blocks that are subject to grade control, mine geologists monitor not only the concentrations of economic metals, but also the presence and abundance of deleterious materials. The preparation and maintenance of models, to estimate NSRs and to assess changes in the levels of potentially toxic materials to be mined, requires close and continuing consultation between corporate departments. There must be strong communication of mine geologists with the mill operators; with the people who market the mine’s concentrates; and, should there be a risk of encountering toxic levels of deleterious materials, with the mine’s health, safety and environmental officers. This co-operation could require radical changes in the structure of many organisations. However, experience suggests that such changes can significantly improve the profitability of a mine.

Mar 22, 2022

By Andreas Brandner

"At the beginning of 2007 the Austrian contractor PORR was awarded with remediation works for a 48-km long part of the railway line from Campina to Predeal – part of the Trans European main Corridors TEN-T priority line 22 Bucurest – Brasov, connecting the southeast European countries with the heart of Europe.Due to partly new realignment and change of regular sections as well as protection against rockfall and slope slide a huge bunch of slope stabilization works became necessary, which were awarded to the contractor PORR and their designer IB-Brandner.Following the studies of the tender documents for the planned protection measures responsible managers of PORR decided to propose an alternative protection design by IB- Brandner. Changing the original design a more flexible and environmentally compatible solution consisting of high performance net, soil nailing and rockfall protection systems (fences) was elaborated and adapted to local needs. During design process, several critical areas were identified and additionally taken into account.In the paper examples of the design and erection process show how difficulties in implementation starting with the presentation of the idea continuing to the realization on site were managed and a technically more sophisticated and commercially competitive solution could be delivered to the customer Romanian Railway – case study.The European Commission awarded – following an election process in which all citizens of the EU could join - the remediation project Railway line Campina – Predeal in Romania as the environmentally best EU co-financed infrastructure project. GENERAL PROJECT EVALUATIONDue to original design slope stabilization should be done by concrete slabs fixed with prestressed anchors and shotcrete cover.The area to be secured was limited to a 12-meter strip left and right from the railway track without reference to nature and local needs. Discussions with the client and his designer and rising awareness for the hazards to address took several months. Site visits in Austria to provide insight in the problems of dealing with natural hazards helped to convince the client of the needs and our alternative design."

Jan 1, 2017

By Luis M. González, Guzmánm Guillermo D., Davis Juan C.

"The Teniente converter (CT) of the Ventanas Smelter and Refinery of Codelco-Chile has two tuyeres for dry concentrate injection directly into the melt.The diluted phase injection system can feed 15 to 20 kg of concentrate for 1 kg of air, which creates a very abrasive solid/gas phase. The tuyeres commonly used lasted for about 3.5 days due to the accelerated decay of the shell, and 1.5 hours were necessary for the replacement of new ones in the reactor.Tests were carried out with common shell tuyeres with a tungsten based welding cover, and a life span of 28 days was reached, increasing the Teniente converter operational continuity between 1.5 to 2 %."

Jan 1, 2009

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

General Aurelio Blanquet,* the best known of living Mexican soldiers, formerly the trusted friend of Porfirio Diaz and organizer of the old Federal Guard of Mexico City, who as a sergeant commanded the squad that executed sentence on Emperor Maximilian, and. more recently was Minister of War in the Cabinet of Victoriano Huerta, landed in Mexico early in April and joined the forces of Felix Diaz. His landing in the state of Vera Cruz, it was stated, was for the definite purpose of aiding the movement now under way to overthrow Venustiano Carranza and to place in power a government that will be "pro-Ally" in its sympathies and will promulgate and enforce laws that will guarantee the rights of life and property in Mexico. The New York Tinges says of the revolution editorially: "Whatever may be the success of General Aurelio Blanquet's attempt to overthrow the Carranza Government in Mexico, admiration cannot be withheld from the General's publicity manager. No enterprise awning at the overthrow of a Government ever had more favorable and widespread advertising. Felix Diaz, whom Blanquet is going to reinforce, supersede, or overthrow, as the case may be-Mexican precedent in these matters offers opportunity for considerable speculation-has been conducting his revolution, at the old stand for some time, but without much success. But, says General Blanquet's representative, the landing of Blanquet will send a thrill to the heart of every true republican.' Meanwhile a biographical booklet is published, adorned with photo¬graphs illustrating the General's record, including such varied matters as the General in favor, receiving a decoration from Victoriano Huerta, and the General in exile, feeding the birds in Central Park."

Jan 5, 1919

By M Liang, C Putzmann, D Gokaydin

The mining industry faces numerous challenges in swiftly evaluating and exploiting new mineral deposits to meet the escalating demand for critical minerals and metals. These challenges necessitate the adoption of innovative techniques and technologies to expedite development cycles and facilitate the efficient exchange of knowledge and expertise. Traditional mineral exploration methods rely heavily on data governance, visualisation tools, and expert interpretation skills, often operating in isolation and limiting the integration of valuable data and knowledge (Lindsay and Perrouty, 2019). To address these integration challenges and bridge the industry’s knowledge gap, the concept of a digital twin offers a holistic solution (Ahn, 2021; Nagovitsyn and Stepacheva, 2021).

Sep 1, 2024

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Iron ore in Minnesota probably carries a heavier tax burden than any mineral in any other place in the world. The State Tax Commission, created in 1907, originated the system, and with the assistance of the School of Mines is constantly making such adjustments, changes and increases as appear necessary, in order to place mineral reserves on the assessment rolls at their true and full present taxable value. The ore bodies on the Mesabi are so well defined by drilling and underground devel¬opment that it is possible to estimate very exactly the volume on every forty acres of land taken as a unit. This is done by the operating or holding company and reported annually to the Tax Commission, Who check the estimates, having all data, and- proceed to fix the valuation for taxation purposes.The first step is to ascertain a general average selling price in open market, over a period of years ; then the total cost per ton (exclusive of royalty) to produce and market the ore. The difference between the average selling price and producing cost per ton is taken as the future full value per ton. This is then discounted at a rate of interest that represents the present and possible future worth of money, over a period of years that will be required to exhaust the ore body, giving the present full value per ton., Iron ore is taxed at 50 per cent of its full value, while other property is taxed at 33 1/3 per cent and 25 per cent."

Jan 1, 1920

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982

By T. Sterry Hunt

Jan 1, 1884

By Fred B. Ely

The first recorded production in the Dutch East Indies was in the year 1893 but seepages of dl were known to exist in North Sumatra, East Java and the east coast of Borneo at least as early as 1880. During the Of the above amount the Royal Dutch produced............................................. 36,006,079 Nederlandsche Koloniale Petroleum Maatschappij (subsidiary of Standard Oil of New Jersey)....................................... 3,867,769 Total Dutch East Indiea....................................... 39,873,848

Jan 1, 1931

By Jonathan Matthews

Efficient and effective management of mine tailings is essential for continued successful development of Alberta?s vast oil sands resources. Syncrude Canada Ltd. continues to research novel tailings management techniques in an effort to improve production efficiency and environmental sustainability. During the summer months of 2001, Syncrude Canada Ltd., in collaboration with members of the Canadian Oil Sands Network for Research and Development (CONRAD), conducted field-scale trials of thickened tailings technology at Syncrude?s Aurora mine, north of Fort McMurray, Alberta. This paper provides an overview of the test program including discussion of objectives, test configuration, and program observations. 0Data collected during the field trial indicate that substantial swings in feed slurry composition challenge effective thickener operation. When coarse mineral solids dominated slurry composition, thickener rake torque rose to unmanageable levels. It was determined that the end-of-pipe depositional characteristics of thickened oil sands slurry were generally consistent with present understanding of oil sands tailings slurries. After shear, thickener underflow product exhibited very shallow beach angles and a limited capacity to keep coarser particles in suspension indicating that stacking of ?paste-like? thickener underflow product from a conventional thickener is not practical in an oil sands setting unless process adjustments can be made to increase the underflow density and/or preserve the initial high yield stress of the underflow during transport and deposition. These technical challenges notwithstanding, Thickened Tailings technology offers considerable promise for recovery of warm water from oil sands process tailings.

May 1, 2003

By Ming-Feng Ye, Guang-liang Wu

The microstructure and mechanical strength variations of chromite pellets preheated and roasted in air were studied systematically. The results show that the chromite (Fe,Mg)(Cr,Fe,Al)2O4 is oxidized to magnesium-rich (Mg,Fe)(Cr,Fe, Al)2O4 and ferrochromium complex oxide (Cr,Fe,Al)2O3 in the preheating process over 500 °C. When the temperature is higher than 1000 °C, the new phase (Cr,Fe, Al)2O3 is formed, which is mainly distributed in the outer layer of a single chromite particle. Inner the particles there are acicular (Cr,Fe,Al)2O3 and unoxidized (Fe,Mg) (Cr,Fe,Al)2O4, which forming an interwoven structure together. The oxidation rates of pellets can reach to superior limits in 20 min. With the temperature increasing from 950 to 1300 °C, the mechanical strength and oxidized rates increase to varying degrees correspondingly.

Mar 1, 2018

By C. E. Corson

THE experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to have received less study and description from the standpoint of the metallographist than many others. The investigation here described was directed to the following points:-Steel containing about 0.50 per cent, of carbon : 1. The structure as related to the temperature, at the same rate of cooling; 3. The structure and physical properties as related to temperature at different rates of cooling; 3. The structure and physical properties as related to different finishing-temperatures and different rates of cooling; 4. The bearing of these observations upon the statement of Prof. Albert Sauveur.1

Sep 1, 1906

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By H. S. Strouth

JAMAICA-bauxite and gypsum-but what else? J Does the Caribbean island have anything more to offer in the form of mineral wealth? One answer may be iron ore deposits which show enough promise to warrant exploitation in the near future by a company associated with Standard Ore & Alloys Corp. In addition, Jamaica is reported to have gold, silver, platinum, copper, lead, zinc, manganese, cobalt, and a great many nonmetallic minerals. Of these, only platinum has not been produced commercially in the past. Right now, Jamaican bauxite is getting most of the publicity, but not too long ago other mining operations were in progress. Lack of proper interest, insufficient roads, and scarcity of venture capital forced those mining properties to suspend production.

Jan 7, 1954