Search Documents

By A. C. Stevenson

THE hoisting equipment selected for use at the Hecla mine in 1907 was one of the first Ilgner type Ward-Leonard controlled hoists put into ser- vice. Development of the Hecla below the 2000-ft. level, which is the ultimate depth of the old equipment, and the additional service required by the "Star," necessitated additional hoisting capacity. It will be our endeavor to give j70u a brief summary of the engineering which determined the selection of the new equipment. The engineer in making his decision as to size, speed, etc., must .make a duty study approximating as closely &s possible the actual opePating conditions which will eventually result. Primarily, it is necessary to know what work must be done. The amount of material which must be hoisted under the maximum condition, as well as its distribution from the various levels of the mine was carefully studied by the mining engineering department, as the ore reserves, their relative-position and the probable method of working them had to be considered. The final figures reached, taking into consideration four different operating conditions, were, in tons per day, as follows:

Jan 1, 1930

By Yoichi Takeda

The CaO-FeO,-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By L. H. Banning

In the fall of 1953 the Philippine Bureau of Mines, under a Foreign Operations Administration Technical Assistance (FOA-TA) program, began a systematic investigation of the nickel content of the well-known Surigao laterite areas, on the island of Nonoc northeast of Mindanao, to determine the occurrence, distribution, and grade of nickel contained in the laterite and in the subjacent serpentine. At the same time, a technical review of the possibility of producing commercial ferronickel from the nickeliferous materials in the Philippine Islands was made, and a smelting process was suggested. The proposed process would be similar to that developed by the Federal Bureau of Mines for the reduction of the nickeliferous serpentine occurring in the Nickel Mountain ?deposit at Riddle, Oreg. The potential avail-ability of electric power from the Maria Cristina facilities at 3 mils per kw.-hr. would enhance the economic possibility of this program. Development of an economically feasible process for recovering nickel from the nickeliferous serpentines and laterites should lead to the establishment of a new industry in the Philippines, to the development of a source of nickel in the Far East, of which at present there is none, and to partial solution of the problem of supplying the free world with nickel. Enough preliminary reconnaissance had been completed by early 1954 to permit sampling of the deposit for metallurgical investigations. The FOA then requested the Federal Bureau of Mines Northwest Electrodevelopment Laboratory, Albany, Oreg., to conduct preliminary electric smelting studies on nickeliferous serpentine and laterite samples.

Jan 1, 1955

Hydraulic backfill is generally retained in stopes using permeable barricades. Mitchell et al (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et al (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading conditions. This paper discusses the circumstances that led to these incidents and analyses the modes of failure. The standards for the safe operating of hydraulic backfill systems are reviewed along with requirements for ongoing management and control. The design requirements of barricade construction are analysed and some appropriate guidelines introduced.

Jan 1, 1998

By Bruno Bussière

Le drainage minier acide (DMA) provenant de la circulation des eaux à travers les rejets miniers sulfureux est sans doute le principal problème environnemental auquel est confrontée l?industrie minière. Afin de prévenir les problèmes environnementaux reliés au DMA, on doit restreindre la présence de l?une et/ou de l?autre des principales composantes menant à la production d?acide, soit l?eau, l?air et les sulfures. Pour ce faire, différentes techniques ont été proposées au cours des dernières années, dont la désulfuration environnementale et les couvertures avec effets de barrière capillaire (CEBC). Dans ce papier, on propose d?utiliser ces deux techniques en combinaison. Ainsi, on produirait un rejet désulfuré à l?usine de traitement qui pourrait, par la suite, être utilisé comme matériau pour la couche de rétention d?eau de la CEBC. Dans un premier temps, on présente les résultats d?une étude de laboratoire qui montre qu?il est possible de désulfurer les rejets de concentrateur à l?aide de la flottation non sélective jusqu?à l?obtention d?un résidu non générateur d?acide. Par la suite, des essais en colonne ont permis de démontrer qu?il est possible de limiter la production de DMA d?un résidu sulfureux à l?aide d?une CEBC dont la couche fine est constituée de résidus désulfurés. Des prédictions théoriques estiment même que la présence de sulfures résiduels dans la fraction désulfurée utilisée comme matériau pour la rétention d?eau peut avoir un effet bénéfique en réduisant la migration d?oxygène. En effet, les sulfures contenus dans la couche de rétention d?eau peuvent consommer l?oxygène qui tente de migrer vers le bas et, ainsi, réduire les flux d?oxygène qui atteignent les rejets réactifs.

Nov 1, 2002

By C. M. G. Wortley, N. Randolph, I. Ralston, R. D. Beck

The ?AMIRA Metal Accounting Project? had its origin in a workshop held in Cape Town on 1 August 2001, with the title ?Challenges in Metal Accounting and Information Management?, which was organised by the Western Cape Branch of the South African Institute of Mining and Metallurgy. This workshop identified the lack of an accepted set of standard procedures for metallurgical accounting as an industry-wide problem. Discussions which followed this workshop led to the initiation of the AMIRA Project P754, ?Improving Metal Accounting?, in 2003. The primary objective of the project was to provide tools for improving the auditability and transparency of metal accounting from mine to product and to facilitate good corporate governance. The planned deliverables of the project were a series of research projects into aspects of metal balancing in different types of metallurgical operations, a Code of Practice on Metal Accounting, and a textbook on the subject which could serve as a guide for metal accounting practitioners and students studying the topic. An additional planned deliverable was the provision of a new variety of professional experts in metal accounting, through successful completion of the research projects. Researchers were engaged at the Universities of Cape Town, Queensland and Stellenbosch and the project was sponsored by five mining companies, including three of the largest global mining groups. Research Program Eight research projects were undertaken as part of the P754 project and these are described briefly here to indicate the scope of the project. University of Cape Town ?Development of a methodology for measurement network design for metallurgical accounting at Namakwa Sands?. This project was based on the Namakwa Sands Separation Plant, with a data rich environment, and involved the investigation of measurement network design through the use of heuristics and the analysis of complex processing circuits. An industry-wide survey of current practice to facilitate the development of an expert system for plant accounting measurements was carried out. ?Metallurgical accounting design at the Waterval UG-2 Concentrator?. The objective of this project is to develop a model for predicting metal recoveries from the different components of a blended ore feed to a plant. ?Optimal measurement network design for metallurgical accounting at Zincor?. This project provided a hydrometallurgical test case for the design and evaluation of a semi-automated optimal measurement network. University of Queensland ?Quantifying the relationship between mine and mill?. This project involved a case study at North Parkes Mine, in which copper and gold ore is tracked from the pit source to the product, as well as a stockpile modelling study. University of Stellenbosch

Jan 1, 2007

The mining companies on the page opposite are among the elite industrial 500 in Fortune magazine's June Directory of U. S. firms that rang up the largest dollar sales volume in 1967. The companies are listed according to their 1967 sales rank, which is given along with their 1966 rank for comparison. Mergers played an important role in the addition and deletion of several companies to the list. Tenneco, Occidental Petroleum and Gulf & Western Industries made the list of mining companies by their purchases of Kern County Land, Island Creek Coal, and New Jersey Zinc, respectively. In turn, these three companies disappeared from the list. General Aniline & Film acquired Ruberoid, and Ideal Cement is now a part of Ideal Basic Industries -a name change only. Only two companies, St. Joseph Lead and U.S. Smelting, Refining & Mining, were actually displaced from the list. The mining industry increased its sales 14.5%, placing fourth among the 22 industrial classifications listed in the Directory. However, among the ten biggest losers in sales were four mining companies-Kennecott Copper, -33.8% ; Asarco, -21.8% ; Amax, -16.5%; and Anaconda, -15.1%.-which was mostly a result of the copper strike, except for Amax which suffered strikes at its molybdenum and aluminum operations. Mining heads the list of industries for return on sales and assets per employee, while it rests at the bottom with respect to sales per dollar of invested capital.

Jan 8, 1968

By Thomas V. Falkie

The title of this talk has brought some interesting responses - even before it was written - from different parts of the country. A geologist from the Western U. S, was deeply concerned with recent layoffs in his profession and the employment situation in general and wondered why "the AIME wasn't doing anything for the benefit of its members." A petroleum engineer in Texas said that a group in his field were studying "professionalism" and their professional status and wondered if there were any words of wisdom for him. A mining engineering professor from the East pointed out that the National Science Foundation did not include mining engineering as one of its recognized fields in one of its equipment funding programs. These are just a few examples of reactions received to date, but they serve to illustrate the broad image that the title has meant to various people. Actually the term profession is defined by Webster as "a calling requiring specialized knowledge and often long and intensive academic preparation." The word encroach means "to enter by gradual steps or by stealth into the possessions or rights of another", or "to advance beyond desirable or normal limits." The intention of this paper, as originally conceived and requested by the program chairman, was to combine those two words literally and talk about how the professional standing of mineral engineers is being eroded from people outside the profession. But the amazing preliminary response suggests that it may be timely to broaden the discussion by including some comments about professionalism in general. In the paper the terms "mineral engineer" or "mining engineering" are used frequently, but it should be clearly understood that much of what is said is valid and is intended for all fields covered by SME and perhaps for AIME in general.

Jan 1, 1972

By P. H. Dudley

I HAVE taken the liberty of calling the researches herein mentioned industrial, to distinguish them from those strictly scientific, where every known appliance is used to insure accuracy in determining principles. The industrial researches are made to ascertain wherein we have failed to embody, in practice, the principles which have been fully demonstrated by the more purely scientific investigations. So far the researches have been mostly confined to the conditions of combustion as used in locomotive furnaces, although we have examined, to some extent, furnaces under marine and stationary boilers. The products of complete combustion are gases, and, knowing what we should have, it is at once shown by analyzing the products whether the desired reactions are taking place. In spite of imperfect furnaces, lack of system in the arrangement of grate-bars and exhaust nozzles, the results are not altogether vitiated, because the analyses are not closer than one-tenth of one per cent., as under the present conditions it is hardly possible to collect gas exactly under the same conditions at different times. All of our industrial operations have developed in the past few years so rapidly, nearly all of them paying, that, until within the past three years, comparatively little attention has been given to their economy outside of the profession. Great corporations have not asked and considered the question in earnest, can we utilize our heat so as to produce the same effect at less cost? The applications of heat are so extensive, entering into every branch of industry, the principal power used to carry on metallurgical processes, to conduct transportation, that its economical generation becomes of universal importance; in fact, its economical generation and application is the leading industrial question of the day. It is stated by those who have given the subject much attention, that in our best steam-engines not over 10 per cent of the theoretical value of the fuel is utilized, and upon locomotives it is far less, probably not exceeding under the most favorable circumstances 5 or 6 per cent. In recent experiments made with the dynagraph, in drawing trains upon the Lake Shore and Michigan Southern Railway from Cleveland to Erie, 95i miles, we found the force required to draw a stock train of 709 tons to be 2,498,396,320 foot-pounds, exclusive of the force to move the locomotive itself. We

Jan 1, 1876

By P. H. Dudley

I have taken the liberty of calling the researches herein mentioned industrial, to distinguish them from those strictly scientific, where every known appliance is used to insure accuracy in determining principles. The industrial researches are made to ascertain wherein we have failed to embody, in practice, the principles which have been fully demonstrated by the more purely scientific investigations. So far the researches have been mostly confined to the conditions of combustion as used in locomotive furnaces, although we have examined, to some extent, furnaces under marine and stationary boilers. The products of complete combustion are gases, and, knowing what we should have, it is at once shown by analyzing the products whether the desired reactions are taking place. In spite of imperfect furnaces, lack of system in the arrangement of grate-bars and exhaust nozzles, the results are not altogether vitiated, because the analyses are not closer than one-tenth of one per cent., as under the present conditions it is hardly possible to collect gas exactly under the same conditions at different times. All of 'our industrial operations have developed in the past few years so rapidly, nearly all of them paying, that,, until within the past three years, comparatively little attention has been given to their economy outside of the profession. Great corporations have not asked and considered the question in earnest, can we utilize our heat so as to produce the same effect at less cost? The applications of heat are so extensive, entering into every branch of industry, the principal power used to carry on metallurgical processes, to conduct transportation, that its econonlical generation becomes of universal importance; in fact, its economical generation and application is the leading industrial question of the day. It is stated by those who have given the subject much attention, that in our best steam-engines not over 10 per cent of the theoretical value of the fuel is utilized, and upon locomotives it is far less, probably not exceeding under the most favorable circumstances 5 or 6 per cent. In recent experiments made with the dynagraph, in drawing trains upon the Lake Shore and Michigan Southern Railway from Cleveland to Erie, 941/2 miles, we found the force required to draw a stock train of 709 tons to be 2,498,396,320 footpounds, exclusive of the force to move the locomotive itself. We

By Henry Kreisinger, John Blizard

This preliminary statement presents some of the results of tests carried out at the Lakeside Station of the Milwaukee Electric Railway and Light Co. , by the fuel section of the U. S. Bureau of Mines , in cooperation with the research department of the Combustion Engineering Corporation of New York . The object of these tests was to determine the thermal efficiency , ease of operation , and other particulars of a boiler equipped with specially designed furnace and burners for burning powdered coal . The boiler tested haş 13380 square feet of heating surface , and is one of eight boilers equipped with the Lopulco powdered coal system supplying steam to two 20,000 -Kw . steam turbines in the largest power house burning powdered coal . Twenty- six tests were run at rates of heat transference varying from 4000 to 8000 B.t.u. per square foot of boiler heating surface , and the mean thermal efficiency attained was about 84 per cent , based on the gross calorific value of the fuel as fired . The efficiency varied little with the rate of steaming , and its high value is accounted for by the small loss from incomplete combustion and the small amount of excess air which varied from 5 to 36 per cent . The coal burned had a gross calorific value of about 11500 to 12800 B.t.u. per pound , contained 2 to 5 per cent moisture , 33 to 36 per cent volatile matter and 9 to 13 per cent ash, and was so ground thaf 89 to 95 per cent would pass through a 100- mesh sieve . The ash had a softening point of 2150 to 2450 degrees F. , but did not fuse together at the bottom of the furnace because it was partly protected from the flame radiation by means of a series of water tubes connected to the boiler which were placed between the fumace bottom and the flame, ..

Jan 1, 1923

One common public perception of mining is that financially it is an extraordinarily risky business. Another and contrary view, in certain circles, is that price risk and other financial risks can be relatively easily removed or shifted by a number of schemes or devices. In reality, beyond the orebody discovery stage, mining need not be any more risky than most heavy industrial businesses. Nevertheless, as stated by Rappaport, (1986): Risk is a parameter of central importance in establishing the economic value of any asset. The level of risk is determined both by the nature of the firm's operations and by the relative proportions of debt and equity used to finance its investments. These two types of risk are commonly referred to as 'business risk' and 'financial risk' respectively. The term financial risk is used somewhat more loosely herein to recognise the reality that any risk inadequately addressed in the design, construction and operation of a mining project can have significant financial consequences; usually negative. For instance, a specific area of business risk in mining is often called technical risk which definitely has severe financial consequences if not managed correctly. The various risk shifting, hedging and risk management tools available all have their place and range from merely useful to almost indispensable. However, in the long-term, financial risks are maintained at acceptable levels by the application of sound, more fundamental business management principles. There are many with a vested interest in perpetuating a perception that the conceptual foundations of sound management practice are extremely complex. In reality, most management concepts are prosaic, but their application requires incredible discipline and hard work. There is no magic formula or 'silver bullet'. It appears that a company whose activities are restricted to mining can analyse the range of risks specific to mine development and operations more clearly than companies in which mining is just one of many businesses. The almost universal failure of large oil companies in the mining business is probably the best example of lack of any clear comprehension of fundamental business characteristics and risks. Conversely, in regard to risk management, choosing to be in other business as well as mining does nothing to reduce the risks of the mining business. The individual shareholder can probably make such 'diversification of portfolio' decisions better than most management teams. It could be argued that diversification across a number of disparate businesses may actually increase overall corporate risk due to lack of management concentration and focus. These differences between the perceptions of financial risks and the realities in mining need to be further elaborated in relation to some uncompromising business concepts.

Jan 1, 1994

By S. McTavish

Since mechanically suitable grinding mills were available in 1908, mill operators have been searching for the best material and design with which to line the mills. These liner systems had to fulfill several criteria. First and foremost they had to last long enough in an operating mill to protect the mill structure from the abrasive wear of the ore and the grinding media. In addition they had to be able to efficiently transfer the energy from the mill to the mill charge in order to facilitate the grinding process. The liners also had to be easily attached to the mill when new and removed from the mill when worn out. The first liners used were generally made of cast white iron, Hadfield manganese, unalloyed high carbon steel and composites of steel and concrete or cemented in flint blocks or natural stone. 1

Jan 1, 1989

By C MacRae, N Wilson

CSIRO Minerals has recently developed an electron microprobe (EMP) based imaging (or mapping) method for characterising ilmenite concentrates. The method requires an electron microprobe analyser to collect elemental X-ray maps which are then processed via an in-house developed software module (CHIMAGE). The type of information readily available from EMP mapping includes; primary phase identification, modal analysis of phases, chemical analysis of individual phases, textural information (eg the alteration stages in the formation of leucoxene or pseudorutile from primary ilmenite and the development of macro-porosity), and the identification of coatings or pore-fill material. All of these parameters will impact on the choice of future downstream processing options considered for any particular ilmenite concentrate. The method has been demonstrated to be a sensitive analytical tool for assessing the distribution of aluminosilicate minor impurities in ilmenite feedstocks from the West Coast of Australia and also for characterising the complex chrome-spinel gangue phases common in East Coast ilmenite concentrates from the Murray Basin.

Jan 1, 2001

By Hiroyuki Matsuura, Fumitaka Tsukihashi

"Emission of CO2 gas from steelmaking industry covers more than 12 % of total CO2 emission in Japan. Though many efforts have been made to curtail energy consumption and high energy efficiency of Japanese steel production process has been achieved so far, further reduction of CO2 emission is strongly requested to develop sustainable steel production process and produce “green material”. Recently, authors have proposed the innovative hydrogen production process, in which water vapor is reacted with discharged steelmaking slag to produce hydrogen gas. This reaction can be achieved without any external energy source and operated by huge thermal energy associated with steelmaking slag and FeO or unrecovered Fe droplets that are relatively rich in the slag. In this paper, thermodynamic calculation results with various initial conditions in terms of hydrogen productivity were presented. Laboratory-scale experiments were also conducted to clarify the validity of thermodynamic calculation and the reaction rate in realistic conditions.IntroductionIronmaking and steelmaking process from iron ore through blast furnace and BOF is an essential steel production route for Japanese steel industries to supply high quality steel products in large quantity to society stably. Blast furnace – BOF process requires huge amount of fossil fuels such as mainly coal, resulting the emission of considerable amount of CO2 gas. Since the emission of CO2 gas from steel industries, about 147 Mt (FY2011), accounts for approximately 12 % of domestic CO2 gas emission in Japan (FY2011),[1] it is an urgent issue for steel industries to develop environmental-friendly ironmaking and steelmaking process and reduce CO2 emission. Various kinds of gases and by-products generated from ironmaking and steelmaking processes have been recycled as much as possible at present. Enormous thermal energy is also generated from processes and released to surrounding atmosphere as various forms such as sensible heats of gases, molten steels or by-products, and as heat losses. However, these energies are not utilized before final dissipation to atmosphere. Although various technologies to utilize thermal energy from ironmaking and steelmaking processes have been attempted to develop, practical application of these technologies has not been achieved because the thermal energy is not always useful as an energy source. In steelmaking process by BOF, fluxing agent such as CaO is added during reefing and thus about 100 kg/t-steel of steelmaking slag are generated. Since the steelmaking slag is discharged at temperature range between 1873 and 1923 K after discharge of refined molten steel, it also has large thermal energy. Amount of generated BOF slag is 11.0 Mt/y (FY2012) in Japan.[2] Assuming the amount of steelmaking slag is 10 Mt/y and its average heat capacity from room temperature to 1923 K is 1 kJ/kg·K,[3] unutilized heat is estimated to be 16 PJ/y, which is equal to annual energy consumption of 420 thousand families in Japan.[4]"

Jan 1, 2014

By Jianhang Hu, Li Yang, Yonggang Wei, Kongzhai Li

"In this paper, the pyrolysis of biomasses including bamboo, sawdust and walnut shell were performed in a tube furnace under temperatures between 400? and 600? to obtain biomass carbon, gas, and tar. Textural parameters analysis revealed the caloric value of biomass carbons between 32 MJ/kg and 34 MJ/kg. It also indicated that the surface of biomass carbon consists of mesopore and macropore structures. By using GC analysis, it was determined the main ingredients of pyrolysis gas are CO, H2, CO2, CH4, C2H4 and C2H6. Calculation states that the density of pyrolysis gas is roughly between 1.0 kg/m3 and 1.7 kg/m3, while the calorific value of pyrolysis gas is between 12000 kJ/m3 and 16500 kJ/m3, illustrating that pyrolysis gas is a median gas. The calorific value of biomass tar was found to be between 32 MJ/kg and 34 MJ/kg, with more than 80 compounds in the biomass tar identified by GC-MS method.IntroductionBiomass as a renewable source is the world's largest and most sustainable energy resource [1].The conversion of biomass has the potential to be a renewable and carbon neutral method of producing fuels and chemicals [2-4]. Pyrolysis is a thermo-chemical process defined as applying heat to degrade biomass in an inert atmosphere. It transforms unstable biomass and other organic materials into biomass carbon, gas, and tar [5]. Biomass carbon can be stored or transported much easier as compared to parent biomass or be converted to value added products such as activated carbons[6]; gas is a relatively low-energy-density fuel; tar can be considered as a source of useful chemicals[7].The characterization of biomass pyrolysis will lead to its increased understanding and utilization as a source of solid, liquid and gaseous products which can be used as fuels and petrochemical feedstock[8,9].In recent years, many researchers studied the effect of temperature on biomass pyrolysis product distribution characteristics in a variety of pyrolysis reactor[10]. Ramin Azargohar's paper [11] presents the results of characterization for biomass and investigates the effects of pyrolysis temperature on the pyrolysis products obtained by fast pyrolysis of four different types of biomass."

Jan 1, 2014

By Alfred E. Hunt

The application of the color-method for the estimation of manganese in iron and steel, based upon the depth of the characteristic purple color of permanganic acid, was first made in this country, the writer thinks, by one of the members of the American Institute of Mining Engineers, Mr. Samuel Peters, in 1874, at the laboratory of the Bay State Iron Company, and was published by him in the Chemical News. The method is credited to him in the new edition of Crooke's Select Methods. The principle of oxidizing manganese with peroxide of lead, or other oxidizing agents, and determining the amount of manganese from the color of the purple permanganic

Jan 1, 1887

By Eric Jones, Leslie C. Thompson

Biological processes for cyanide detoxification in mine waste are receiving attention as an alternative to conventional chemical treatment options. Some of the advantages of biological treatment include: Low comparative treatment cost * Shorter treatment time * In Situ Treatment * Complete Detoxification - Ends long-term liability - Eliminates in-perpetuity monitoring - Natural Re-Vegetation potential Natural and non-toxic nutrients, by-products and process end-products Hecla Mining chose a bio-neutralization process developed by Pintail Systems, Inc. for cyanide detox in spent are and process solutions from heap leach operations at the Yellow Pine Unit. The Yellow Pine operation is located 50 air miles east of McCall, Idaho, in the Stibnite Mining District. This district is a historic mining district dating back to the early 1900's. During World War II, this district produced a majority of the antimony and tungsten the United States using for the war effort. More recently, the Stibnite district has been known for its gold production. Hecla Mining Company is based in Coeur d'Alene, Idaho, and is a leading domestic producer of precious metals and a major supplier of specialty aggregate and industrial minerals. Pintail Systems, Inc. is a company specializing in the development of biological treatment processes for mine waste remediation. PSI has offices in three states and a laboratory, pilot plant and field office in Aurora, Colorado

Jan 1, 1993

The paper presents results of the mineralogical examination on samples from a bacterial leaching test which simulated in situ leaching for 482 days. Rock fragments (15 to 20 cm) were obtained from the top, the middle and the bottom of a bioleach column. Examination of the samples was carried by electron microscopy and image analysis. The surfaces of the rock fragments were studied to characterize the precipitation products, and cross-section cuts were studied to assess the advance of the bacteria leaching front and the dissolution of the different sulphide minerals.

Jan 1, 1991

By W. J. Slatosky

As a means of effecting better control of endpoint temperatirres at the Jones & Laughlin basic oxygen furnace plant, a set of mathematical equations has been developed. The eqlutions are the product of a themlochemical anaysis of the process and aye designed to calculate the required scrap, lime, and hot metal additions in terms of a number of independent variables. Results of test heats have warranted adoption of this technique by the Prodrrction Department. BECAUSE of the autogeneous nature of the basic oxygen steel-making process, bath temperature can be controlled without an external fuel supply by charging the furnace with additions that are thermally balanced. The thermal requirements of the charge materials are such that, during the refining process, they throttle the heat generated by the metallurgical reactions in a manner designed to result in a speci-fied temperature at the completion of the heat. In the past, operating personnel at the basic oxygen furnace plant of Jones & Laughlin's Aliquippa Works relied on their experience and technical knowledge of the process to determine the quantities of charge additions needed to result in a finishing temperature in the range 2880"to 2920" F. (The charge consists primarily of 93 tons of scrap and hot metal plus an amount of lime sufficient to maintain a basicity ratio of 2.8 to 3.2). Estimates of these materials are based on a consideration of the effects on finishing temperature of 1) iron silicon content, having a variation of 0.8 to 1.8 pct; 2) iron temperature, ranging from 2250°to 2600°F; and 3)any excessive cooling of the furnace due to a production delay. The end temperature of the preceding heat also serves as a guide in that, if a heat was within the specified temperature range, the succeeding heat could be charged with materials of nearly the same proportions, provided the hot metal used in each of the two charges was of approximately the same temperature and composition. On the other hand, if a heat was outside the specified tapping range, or if the hot metal used in that heat was of different analysis and temperature from that of the iron to be charged, an adjustment in the proportion of additions is in order for the following heat. Due to the complex thermochemical behavior of the process and to the inexact and subjective nature of the described method of determining charge additions, consistently accurate temperature control was not to be expected. Therefore, those heats out- side the specified tapping range necessitated subsequent adjustments by either reblowing the cold heats for a suitable length of time so as to elevate the bath temperature to the desired level, or cooling hot heats with a proper amount of scrap. Because extra time is required to make these adjustments, production is delayed. In an attempt to devise a method for improving temperature control, an analysis of the thermochemistry of the process was undertaken. This, in turn, led to the development of a set of mathematical equations which enable the calculation of the quantities of scrap, lime, and hot metal needed to result in any specified tapping temperature range. The analysis was not intended to be a repetition of work done by others such as McMulkinl or ~hilbrook.' It was meant to be an extension of their work so that charge additions could be calculated not in terms of silicon alone but, rather, as a function of all independent variables. This paper presents the derivation of these relationships, their effectiveness in controlling bath temperatures, and a method of utilizing them on an operational basis. The Heat Balance—The first step undertaken in the analysis of the problem was the enumeration of the pertinent variables. A list is presented in Table I where it is noticed that these quantities have been separated into the following three categories: important variables, variables considered as constants, and variables to be neglected. The breakdown was an arbitrary one designed to facilitate the analysis; otherwise, the mathematical treatment would have been exceedingly cumbersome and complex. Fortunately, experience has shown that these simplifying assumptions do not seriously impair the accuracy of the calculations. These variables along with the limiting assumptions listed in Table n were then used to write a heat balance of the process by applying the equation of continuity, Rate of Rate of Rate of Increase = Income - Outgo PI ] of Heat of Heat of Heat.

Jan 1, 1962