Search Documents

Mineral Processing Engineering Education in China - Bringing up the Engineering Diathesis and Design Competence of the College Students

Sep 13, 2010

By Daniel Rodríguez Hoyle

El presente texto señala una breve reseña histórica sobre el cobre, producción, exportación, consumo, reservas y su expansión mundial en el Perú durante los últimos cinco años.

Jan 1, 1968

By Ruirui Wei, Mingrui Yang, Xuewei Lv

Copper slag is a by-product obtained during smelting of copper from copper ores. In China, for one ton of metal production about 2.2 tons of copper slag was generated, and approximately 15 million tons slag is produced in 2013. Dumping and disposal of such huge quantities of slag will cause environmental and space problems. Most importantly, copper slag cannot be made full use of to maximize its value. In this study, copper slag was used to take the place of scrap iron and part of silica in traditional process and to produce FeSi alloy as the main material. Utilizing silica and copper slag as the raw materials and coke as the reducing agent, FeSi45 was produced in the induction furnace. In addition, the effect of different n(C)/n(O) on FeSi45 has been investigated.Increasing n(C)/n(O) is beneficial to form the stable phase of FeSi. Meanwhile, n(C)/n(O) greatly affects the reduction and recovery of silicon than iron. When n(C)/n(O) equals 1.10, the recovery of silicon and iron is about 77 and 95%, respectively.

Mar 1, 2017

By Frank H. Reed, P. W. Henline, Harold W. Jackman

A SUMMARY of the consumption of coal in 1945 shows that the coke industry accounted for 17 pct of the total coal used. No substitute for coke and the blast furnace in the reduction of iron ore has gained sufficient prominence so far to be given serious consideration. However, while the same slot-type ovens are being built and used now as were in use a few years ago, the problem of obtaining suitable coking coals, both high- and low-volatile, has forced many operators to revamp coal-blending facilities. Until the beginning of World War II, high-temperature coke plants were able to secure the required high-volatile and low-volatile coals from two or three seams and from three or four mines. Thus, many of our coke oven plants were able to operate with storage bins for two coals only. The variance in raw materials was not great, and uniformity of blend was a relatively simple problem. Since the beginning of World War II, many and important changes have taken place. Demand for all coals increased greatly. Production, though kept as near maximum capacity as possible, could not meet the demands for coal generally, and particularly for the various kinds of coal which have proved to be satisfactory for specialized uses; coals were allocated as nearly as possible in the order of greatest need; storage piling was reduced to the minimum necessary to keep plants in operation; uniformity of quality could not be maintained, and with this last, uniformity of composition of blends for coking could not be maintained. Whereas before the war producers of metallurgical coke could fill their needs from three or four mines, by the end of the war it was not unusual to find shipments to a single coke oven plant coming from as many as 30 different mines, in a single month. Since many of the mines producing both high- and low-volatile coal for high-grade metallurgical coke are rapidly nearing depletion, the problem of seeking new sources and of blending a number of coals in each plant for the production of high-temperature coke is facing practically every producer in the United States at the present time, and is one which will probably continue for many years to come. Midwestern by-product coke ovens in the Chicago and St. Louis areas use annually from 12 to 15 million tons of bituminous coals which are transported 500 to 700 miles from the Appalachian coal fields of Pennsylvania, West Virginia, and eastern Kentucky. Approximately two-thirds of this coal is high-volatile bituminous. The critical transportation problem confronting the nation in 1943, and the growing scarcity of the best Appalachian coking coals, prompted the Illinois Geological Survey to propose a research program in which would be studied the coking properties of blends of low-sulphur, high-volatile Illinois coal with the high- and low-volatile coals from the eastern fields. Such blends containing Illinois coal, if substituted for the all-eastern blends normally coked,

Jan 1, 1948

By A M. Ebbels

"Underground mine scheduling decision-making has been based on production requirements, equipment productivities and the mine planner’s instincts on the best scheduling strategy for the mine to optimise the net present value (NPV) of a project.In the last few years, innovative software has been developed to optimise underground schedules based on NPV. The schedule optimisation tool (SOT) allows the user to set up scenarios based on grade, metal content, capital and operating costs.This paper discusses the results of two case studies undertaken using the SOT software to optimise the NPV of the projects.In each case study, the SOT software has been applied in two ways:using the original mine planner’s scenario and determining whether the NPV could be improved by changing resource capacitieschanging the scheduling goals to determine whether a different mining strategy would have a better NPV outcome.The outcomes of the case studies demonstrate that the mine layout and design were contributing factors to the overall improvement of the NPV and that SOT has a more noticeable impact on the NPV of projects where less sequence constraints are required, such as geotechnical sequencing and access development.CITATION:Ebbels, A M, 2016. Optimising underground mining strategies, in Proceedings Project Evaluation 2016, pp 60–65 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By G. Cordingley, A. Mwanza

Lumwana is an open pit Copper mine located in the Northwestern Province of Zambia approximately 80 km west from the provincial capital of Solwezi, approximately 300 km northwest from the Copperbelt and 700 km northwest from the national capital of Lusaka. The mine has two major Copper deposits: Malundwe and Chimiwungo. Copper mineralization includes Chalcopyrite, Bornite and Chalcocite. In addition to Copper, these deposits also contain the undesirable element Uranium contained in vein hosted and disseminated Uranite. The processing plant was designed using conventional technologies: semi-autogenous grinding (SAG) and ball mill for grinding, and mechanical cells for rougher and cleaner flotation. Soon after commissioning in early 2009, it was recognised that two stages of conventional cleaning were unable to produce plant final Copper concentrates with the desired Uranium grades. Studies have shown that a significant quantity of liberated and fine Uranium particles (up to 80-90%) is recovered with the concentrate by entrainment. Lumwana Operations sought the use of the Jameson Cell technology after observing successful implementation at other sites in rectifying similar issues. In late 2009, Jameson Cell pilot-plant test work was conducted at the site and this quickly led to the installation of a full-scale B5400/18 model into the existing cleaner circuit. Inclusion of the Jameson Cell resulted in the plant being able to effectively produce clean and saleable concentrate with Uranium contents consistently below acceptable levels. Initially designed to be used as a cleaner scalper cell at the head of the existing conventional cell circuit, subsequent operational issues with the existing recleaner cells forced reconfiguration of the cleaner circuit and reintroduced the Jameson Cell for the recleaning duty. This paper reports the Lumwana Operation from the first two years of operation where it struggled to produce a saleable concentrate with Uranium grades below 150 ppm, which is the maximum allowable limit set out in the smelting contracts, to steps taken in the subsequent years to implement a satisfactory solution. The plant can now consistently produce a clean Copper concentrate with Uranium grades well below 130 ppm and the overall improvements implemented at site have seen the overall plant recovery improve by 1.3%.

Jan 1, 2014

By Miguel Vera Barrientos

Dado que el desarrollo de labores mineras se ve influenciado por el conocimiento del macizo rocoso puesto que otorga mayor seguridad a las personas, equipos e instalaciones en operaciones interior mina, el presente texto plantea un método sistemático para la rectificación de muestras de roca intacta con tablas de valores empíricos y escalamiento de los resultados.

May 1, 2015

By AIME AIME

THE report of the united. States Steel Corporation for the' year 1928 gives the, following ,figures of raw materials and' finished products . Raw materials, tons :

Jan 1, 1929

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

By M. H. Moys

I had the good fortune to attend the above Conference which was held in Kanpur, India, on 11-15 December, 1995. The Conference was held in honour of Professor P.C. Kapur of the Indian Institute of Technology in Kanpur. Professor Kapur was one of the early students of legendary teacher and researcher of mineral beneficiation, Professor Doug Fuerstenau of the Department of Materials Science and Engineering at the University of California at Berkeley. I have attended my fair share of international conferences and this one certainly rated at the top of the list on several counts. With an open-hearted hospitality which one might almost take for granted once you have spent some time in India, the organizers of the Conference looked after every need of their guests, including breakfast and transport to and from the conference centre, wonderful traditional lunches and dinners and outstanding entertainment in the evenings. The papers were generally of a high standard, and debate flowed enthusiastically and freely. Several international guests delivered seminal papers in their fields as discussed below.

Jan 1, 1996

By V. Polotski

This paper describes a platform for autonomous operations in open pit mining environments. A typical operation consists of: (1) Initial locomotion toward a remote worksite; (2) Pattern navigation within the worksite; (3) Worksite manipulations and (4) Return locomotion to the start location. The platform includes precise localization module based upon the fusion of odometry, inertial and GPS measurements. The guidance module starts from a set of way points specified on a GPSreferenced map and plans and executes the mission. A typical mission includes specified manipulative tasks along the navigation path. During motion execution the on-board system continuously verifies that the path is free of obstacles and that the hardware is not overloaded. Momentary losses of external positioning measurements does not adversely affect the performance, owing to the redundancy in position and heading estimation. A rehearsal phase follows planning and allows the supervisor to examine the kinematic behavior of the platform during motion, thus reducing the need for continuous monitoring during execution and providing protection against potential losses of communication.

May 1, 2003

Beaches contain the residue of eroded rocks which have resisted weathering, and it is common to find in all beaches some of the harder, heavy minerals. The natural sorting action of waves and winds tends to concentrate the heavy minerals into banded deposits.The value of such deposits is extremely variable. Even amongst the more concentrated deposits, the principal minerals, in the vast majority of cases, are magnetic, titaniferous magnetite and other forms of iron oxide, which, in the present state of mineral economics and technology, are of little or no value.Valuable minerals of fairly common occurrence in beach sand deposits are rutile, zircon, ilmenite, monazite and chromite, and each of these minerals, as well as others of less common occurrence, is obtained from beach deposits in various parts of the world.Along a stretch of 300 miles of coast from Coff's Harbour in New South Wales to North Stradbroke Island in Queensland, occur unique concentrations of heavy minerals. The principal minerals which occur are rutile, zircon and ilmenite, and for some years these deposits have contributed half to three-quarters of the world's consumption of rutile and zircon 1, ,2. The only other notable beach sand concentrations in Australia are at a number of places in the southwest of Western Australia, where deposits containing highgrade ilmenite are being developed.

Jan 1, 1950

By A J. Cornah

"The mine geologist’s role in classifying ore from waste during grade control represents a critical link in the mining value chain. Any improvement in the ore/waste selection success rate (thus reduction in misclassification) which can be delivered by the mine geologist represents a value proposition. Improvement achieved without additional operating cost (for example extra drilling and sampling) will directly and immediately add value to the mining operation and therefore clearly must be pursued. Such improvement may be leveraged from existing resource drilling data which are typically less numerous but better quality than the grade control data. They are usually excluded from grade control estimates (termed the ‘base case’ approach here) because of the differences in quality.Various specialised geostatistical tools are available to account for differences in precision and accuracy between data sources during spatial estimation. This paper uses a conditional simulation (CS) case study to assess the benefit of integrating resource data into grade control estimates through ordinary kriging (OK) of pooled data sets, cokriging (CK), and ordinary kriging with variance of measurement error (OKVME) when the grade control data are:unbiased but increasingly imprecisebiased and increasingly imprecise. The premise assumed is that the resource data are unbiased and precise.The paper demonstrates that, if appropriately handled, resource data may be used to improve grade control estimates and thus improve ore/waste selection success without additional operating cost. Where grade control data are imprecise but unbiased it is recommended to integrate resource data using OKVME. This re-appropriates kriging weights from less precise to more precise data locations and improves the grade control estimation precision compared to the base case; it consequently provides an improvement in the grade control selection success rate. If grade control data are associated with significant bias, integration through CK is recommended as the biased data are zero sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case and consequently improvement in the ore/waste selection success rate.CITATION:Cornah, A J, 2014. Incremental improvement of grade control models using resource data, in Proceedings Ninth International Mining Geology Conference 2014 , pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By J. B. Mudd

Introduction It is difficult to think of any activity on which mankind has been more dependent than mining, and certainly there is much evidence in almost every part of the world of old workings that clearly demonstrate that man from earliest times has dug and toiled to take from the earth precious stones, metals and materials that from time to time have been essential or of value to him. In step with social development and industrial and technological advances the tempo of mining activity, regulated only by the laws of supply and demand, has quickened and in this century has accelerated rapidly in keeping with its dramatic development. Indeed, the rate of change of events has been such that if it were to continue to accelerate as fast as it has over the past decade there is reason to wonder how the insatiable demands for metals and minerals are to be met in the years that lie ahead. Shallow mines containing high-grade ore deposits either have been or are being rapidly mined out and their place can only be taken in general by ore lying at greater depth, or by ore of low grade, situated for the most part in remote and in underdeveloped areas. The cost of exploration and development is rising at an alarming rate, with the result that the expenditure now required to bring a mine to production far exceeds anything previously contemplated. It is estimated that the total capital required to maintain existing operations and develop new ones during the next 5 years will be of the order of $50,000 million and of this, new capital to bring new mines to production will be of the order of $3,000 million. Today no single mining finance company can, from its own resources, find all the money for a major mining development, and as a consequence there has been a strong trend toward joint ventures and to the formation of multinational consortiums. International lending institutions already play an important part in financing many new mining projects and their participation provides the financial umbrella under which other lenders can invest with greater security. There is little doubt that to finance the costly ventures in the future, governments and international lending agencies, banks and finance

Jan 1, 1971

By Z. H. Zhou

It is difficult to remove cadmium from raw indium using only electrolytic refining because their standard potentials are similar. In this paper, physical and chemical methods were used to remove Cd from raw indium. Indium metal is vacuum refined for two hours at 400°C with a vacuum pressure of 20 Pa. In this process, 99.70% of the Cd can be removed. The removal rate of Cd reaches 90% to 95% when indium is further smelted for 10 minutes in a 20% glycerin solution of KI and I2 at 180°C. When pre-indium is electrolytic refined in an In2(SO4)3-H2SO4 system, in which the indium content is 80 to 100 g/L, the pH is 2.0-3.0 and the current density is 80 to 100 A/m2, the contents of the impurities decrease and the purity of the indium product reaches 99.99%.

Jan 1, 2007

This paper describes the sinking and lining of a 14 foot 6 inch finished diameter shaft down to and into the salt of a typical dome of the Gulf States region. The conditions and nature of the strata encountered divide the work into three distinct sections - that in (1) alluvial surface deposits, sunk through by open caisson methods, (2) water bearing rock, directly above the salt, and in (3) salt. ACKNOWLEDGMENT The writer wishes to acknowledge the cooperation of the sinking contractors, The Dravo Contracting Co. of Pittsburgh, Pa., through E. T. Gott, vice-president, in furnishing the data used in this paper.

Jan 1, 1932

By Helmut Thielsch

METALLOGRAPHIC specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production " requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and photography in electron microscope and (5) interpretation. PREPARATION OF METAL SURFACES Usual metallographic polishing is generally satisfactory. It is important though that the final polish be applied very care- fully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside from superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the same for 20 min. in a solution containing 8 grams cupricsulphate in 40 C.C. of concentrated HCl and 40 C.C. of H20 (Marble's reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by 10 min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

By P. G. Chamberlain, E. R. Podnieks, R. E. Thill

Although published data on the physical properties of rock are voluminous, information is often lacking on the environmental conditions under which such data were acquired. Efforts are frequently directed to improve specimen tolerances and preparation procedures; but investigators often overlook giving the rock environment equally careful control during the testing program. Generally, tests are conducted at existing laboratory room conditions, and the prepared rock specimens are frequently, if not most commonly, air-dried for various lengths of time before testing. The standard testing atmosphere recommended by the American Society for Testing & Materials (ASTM)1 is 73.4°F and 50% relative humidity. To maintain a rock at 50% relative humidity for testing purposes, however, requires special equipment and preconditioning procedures, as this study demonstrates. Relatively small variations in the moisture content of a specimen, for example, due to the coolants or lubricants used during specimen preparation, can cause significant variations in the physical properties measured. Such moisture variations may occur in the rock specimen even after it is air-dried, since laboratory humidity conditions commonly fluctuate from day to day. For these reasons, this study emphasizes procedures for preconditioning and maintaining a controlled environment during testing. Although the effects of moisture or temperature on rock properties have previously been studied, their combined effect on rock properties is unknown. In this study, uniaxial compressive strength, Young's and stiffness moduli, and longitudinal wave velocity were determined and compared under controlled conditions of temperature, moisture, and pressure for 11 environments considered to be of particular interest in laboratory, in-situ, and even simulated lunar environments. The following environments were selected for this program: -250°F under dry, 50%

Jan 1, 1972

By F. W. Benn

The Bureau of Mines investigated flotation methods for recovering fluorite and byproducts from two samples of the Fish Creek deposit in Eureka County, NV. The preferred method for tre.ating a fluorite-beryllium sample included (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, (3) muscovite flotation, (4) silicate flotation, (5) sodium hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concen-trate. Laboratory results showed that over 94 pct of the fluorite was recovered in a recleaner concentrate containing 98 pct CaF2, Beryllium flotation produced concentrates containing in excess of 5 pct BeO with recoveries over 70 pet. The preferred method used for a fluorite-mica sample consisted of (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, and (3) mica flotation using an anionic-cationic collector system. Laboratory results showed that 84 pct of the fluorite was recovered in a recleaner concentrate containing 96 pct CaF2, Mica flotation produced a concentrate containing 95 pct mica at 85-pct recovery.

Jan 1, 1986

By H. R. Banks

THE Sullivan concentrator has completed 20 years of operation. During this period a considerable amount of data has been accumulated concerning the characteristics of several types of flotation machines in their application to the problem of the differential separation of the lead sulphide, zinc sulphide and, in more recent times, iron sulphide, in the ore from the Sullivan mine. It is the author's intention to sketch briefly experiences encountered when the several types of flotation machines were introduced into the flow. ORIGINAL FLOTATION EQUIPMENT AND ORE The original flotation equipment consisted of four 18-cell lead-roughing machines, whose concentrate was cleaned in an 8-cell and recleaned in a similar 8-cell machine. Zinc concentration was carried out in four 18-cell machines. One 8-cell zinc re-treatment machine received the reground zinc middling. The 168 cells handled some 3000 tons of original daily feed. These cells were of the standard Minerals Separation type, equipped with 24-in. impellers. Spindles were driven through geared line shaft at a speed of 255 r.p.m. The impellers were the 45° type, except for the last three cells of the zinc-rougher machines, which were of sub-aeration type, with full bottom shroud and half shroud for the top side of the impellers. Four-pound air was introduced. This recognition of the benefit of intensified flotation operation for "gleaning" was an important phase in the early operation and will be discussed further on in this paper. Sullivan ore during this period is described as a finely disseminated mixture of four sulphides, totaling 90 per cent made up of 13.6 per cent galena, 14.4 per cent marmatite, 1 per cent pyrite and 61 per cent pyrrhotite. The specific gravity of the ore was approximately 4.4. There has been a gradual change in the ore content. The 10 per cent of nonsulphide constituents has increased to between 15 and 20 per cent and all three sulphides have dropped somewhat. Added equipment and changing technique have made possible the treatment of 8000 tons per day of mill feed instead of the 3000 originally handled. SPECIAL FEATURES OF FLOTATION AT SULLIVAN Sullivan flotation differs greatly from customary practice. The very heavy return of lead rougher middling and lead cleaner tailing, totaling at times 125 per cent of the new feed tonnage, has been the subject of much investigation. The practice is still employed.

Jan 1, 1944