Search Documents

By K. Tabra

In a mine operation, the proper strategy to handle residues is one of the main concerns, in particular when dealing with mine/plant liquid effluents. Most active water treatment systems at metal mines rely on standard alkali-addition procedures. However, the increase of mineral prices, stricter environmental standards and high metal content in some effluents, has led to the development of alternative treatment techniques for their removal and/or recovery. This article presents a roadmap to face mine wastewater treatment requirement, with focus on two active treatment strategies: 1) conventional lime-based technology and 2) the use of NaSH or Fe(OH)3 for metal precipitation and separation, including possible valuable elements recovery. The Roadmap consists of 1) Approach to effluent treatment 2) Characterization 3) Precipitation tests 4) Solid/liquid separation tests and 5) Economic analysis.

Feb 27, 2013

By E. Stansfield

IT. has long been known that coal is unstable and oxidizes in air, even at ordinary atmospheric temperatures; also, that such oxidation affects the analysis of coal. Nevertheless little or no precaution is taken to prevent oxidation in the ordinary methods of analysis, and the possibility of error due to oxidation is sometimes ignored even in researches on coal. Although the general nature of coal oxidation is well known, and many workers have made careful studies of the rate of oxidation of different types of coal exposed to oxygen at different temperatures, yet the amount of oxidation coals undergo in the ordinary process of analysis, and its influence on the determined analysis, is not well known, and the published data are widely scattered through the literature. This paper is a collec-tion, from this laboratory, of data that bear on the subject, together with a brief summary of three methods employed here to evaluate the oxidizabil-ity of coal. The post-Carboniferous coals of Alberta range all the way from anthracite down to lignite. As some of them are notably susceptible to oxidation, the necessity for care was early forced upon our attention, and oxidation has been reduced either by the removal of air with a vacuum pump or by the displacement of air with natural gas (methane). The two routine analytical operations most liable to involve oxidation are the preliminary, partial drying of the crushed coal (called air-drying) and the determination of moisture. The first is a prolonged operation on coarse coal at ordinary temperatures, and the second a short treatment on powdered coal at higher temperatures. Oxidation also occurs in coal samples stored in ordinary sample bottles. In order to gain information for this study, determinations were recently carried out on the same samples in air, in natural gas, and in vacuo. Sixteen coals were tested; three would be classed in the United States as coking bituminous coals, two as noncoking, nonslacking, bituminous coals, and the rest as subbituminous. Table 1 gives typical analyses of these coals as mined.

Jan 1, 1934

By Jack D. Melin

The commercial development of the Liwell Screen is a result of a thorough search for a non-blinding and highly efficient screening device capable of handling even the most difficult-to- screen feed materials. A proprietary development of Hein, Lehmann A.G. of Duesseldorf, West Germany, the Liwell Screen utilizes a unique flexible deck motion for sizing a variety of sticky, high surface moisture feed materials including raw coal and lignite at separations ranging from 3/4-inches (19mm) down to 10 mesh (1.5 mm).

Jan 1, 1983

By Clarence M. Haight

The general practice in drill sharpening shops, of which descriptions have been written, is about as follows: The bit is heated to 1600" to 1900°F. Then when forged to the proper shape and size in the sharpening machine, the steel is allowed to cool; it is then passed to a hardening furnace where only the end is heated to about 1450" F., and then quenched in cold water, brine, or in brine with oil on top.

Jan 1, 1922

By Stephanie Singarayer, Damodara Reddy Chinnasane, Mike Yao, Danielle Pelletier

Mining at Vale’s Creighton Mine has been active for nearly 120 years in Sudbury, Ontario, Canada. Being the deepest mine in the Sudbury region, mining induced seismicity is a common occurrence at Creighton Mine. Over the past five years, 26 large magnitude seismic events ranging from 2.5 Mn to 3.7 Mn (Nuttli) have occurred. Out of these large magnitude events, three 3.0+ Mn events occurred between April 2020 and January 2021. The majority of the 3.0+ Mn events are believed to be the fault-slip type that could be linked to the known major geological structures and/or long-term effect of mining over many years. The recent large magnitude events are believed to be triggered by high induced stresses while mining the first few stopes of a new lower horizon in the top-down centre out mining sequence.

Apr 26, 2022

By M. E. Rossi, J. E. Camacho

"Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations to assess the uncertainty of mineable reserves at the project’s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the correct (or accurate) characterization of uncertainty, adequately describing the variability observed from the data and its effect on the final objective.The objective of this paper is to compare the ad-hoc uncertainty model provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered, the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme.The application described in this paper is taken from a medium-sized Cu open pit and underground mine in northern Chile, and demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more traditional resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit."

Jan 1, 2004

By K. D. Allen, M. J. Blattman

The problem of measuring the amount of rock removed during a given time interval is faced by most mining operations. Many methods have been developed with varying degrees of success, dependent upon the mining method and the availability of usable data. The Rosebud Mine has been in production for nearly two years, employing several techniques to estimate monthly production from underground production stopes. The use of three-dimensional solids generated from survey data has greatly improved the reliability and confidence of monthly production reports. The authors will summarize the methodology currently being utilized at Rosebud.

Jan 1, 1999

By K. N. Weaver

In the early 1950's the cement industry began putting a new emphasis on geology. This article points up some of the industry's raw materials problems that geologists are uniquely qualified to handle. Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War 11, however, the industry began to recognize the need for geological exploration and some of the larger companies began to build a permanent geological staff. This development has its roots in: 1) The rapid expansion of the industry. After World War II and continuing into the early 1950's the demand for cement far exceeded the production capacity. This placed a great deal of pressure on the producers to enlarge capacity at their plants and to develop new sites. 2) The closing of many cement plants due to inadequate raw materials. Producers feared lack of raw materials due to inadequate exploration and evaluation. 3) An ever increasing pressure for upgrading of the quality of portland cement, necessitated upgrading the quality of raw materials. 4) The increasingly large capital investment needed to build new cement plants required a higher degree of accuracy in reserve calculation. These reasons are more or less self explanatory and will not be elaborated on. They are outlined to illustrate the probable evolution of thought among cement management to justify the development of a geological staff. In the author's personal experience the geologist must continually readjust to changing conditions within the industry. For example, cement production capacity grew so rapidly that today production is only about 70% to 75% of rated capacity (73.8% in 1963). Therefore, whereas the geologist's function during the active expansion of capacity was primarily one of exploration, one of his major functions today is the development of existing reserves. This assumes of course that reserves at existing plants have been proven to be adequate in terms of the company's reserve policy. Through the proper development of raw materials, the geologist can markedly influence quality control, production and long range planning. Examples of several of the operations of Medusa Portland Cement Co. will illustrate how proper attention to geologic detail pays off in the above areas. Because limestone is the major raw material of port-land cement, the examples will be concerned with it. DEVELOPMENT OF GEOLOGIC DETAIL One of the prime objectives of an exploration or development project should be the establishment of the stratigraphy and structure of the deposit. The basic tool for exploration and development is still the core drill, and the geologist must gain a maximum amount of information from a minimum amount of drilling. In order to obtain this objective the following is essential: 1) Adequate detailed geologic logging of cores. The core is first logged and separated into lithologically distinct units. In order to make the lithologic breaks as meaningful as possible, representative pieces of core (not all) are etched in dilute HCI. This removes the "drill polish", brings out the structure of the rock and indicates the proportion of dolomite and argillaceous material because dolomite and argillaceous material etch in relief. In this way the lithologic breaks become clearer and one gains a general idea of the chemical makeup before analysis. This method of logging lessens the probability of including two types of stone, e.g. limestone and dolomite into the same sample for chemical analysis. 2) Representative sampling for chemical analysis. After logging, the lithologic units are sampled for chemical analysis. A representative analysis can be obtained by extracting a 1-in. sample for every foot of core. For example, a lithologic interval of 10 ft to 20 ft would yield ten 1-in. samples taken at 11 ft, 12 ft, 13 ft... and 20 ft. These samples are then crushed, pulverized and split into a sample for chemical analysis. This sampling method represents a significant saving of time over splitting the entire core. 3) Preparing the core as a record. Because of the expense of storage and the difficulty of handling large amounts of core, only representative samples of each lithologic unit are saved for reference. An

Jan 1, 1965

By Andrea Koschinsky, Luise Heinrich, Stefan Gößling-Reisemann

"Germany, like several other countries, has entered a contract with the International Seabed Authority (ISA) to explore the prospects of commercial manganese nodule mining in the Clarion-Clipperton Zone (CCZ). Ensuring a maximally sustainable deep-sea mining operation requires a thorough understanding of the environmental impacts associated with every step of the mining process from the extraction of the nodules at the seafloor to the refinery on land. Against this background, the project presented here applies a combination of scenario-building and life cycle assessment (LCA) to assess and evaluate the sustainability performance of the individual process steps as well as the entire mining operation.Life cycle assessment (LCA) is a comprehensive methodological framework that allows the identification and quantification of impacts occurring during a products life-cycle, as well as the analysis and evaluation of their contribution to pre-defined impact categories, such as climate change, acidification and toxicity (Rebitzer et al., 2004). Until now, LCAs with a focus on raw material extraction have almost exclusively been applied to terrestrial processes. Noteworthy exceptions are offshore drilling, offshore wind farms and ocean fishing. Hence, the first part of the project is to investigate in how far LCA can be applied to deep-sea settings and if and in what way it could be adapted to be used in a deep-sea mining context."

Jan 1, 2017

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

By S. R. Steinacker, H. Schnideritsch, J. Antrekowitsch

Primary copper industry flue dust plays an increasingly important role in the creation of matte and slag. From a thermodynamic point of view, the chemically formed section of fine particles play a techno-logically interesting role in comparison to the mechanical carry-over. Here, the volatilization and the sub-sequent condensation in the off gas system lead to a characteristic distribution of the contained elements which are represented by various compounds of desired metals like zinc and lead. On the contrary, certain undesired components such as arsenic, bismuth and cadmium accumulate within the product as well. This paper describes existing models and theories concerning the formation of flue dust in the copper smelting process and presents a thorough investigation of the physico-chemical fundamentals by verifying assump-tions with thermodynamic calculations. By fully understanding the formation patterns at different stages and temperatures within the process, better knowledge for flue dust in the first step of the pyrometallurgi-cal copper smelting can be obtained - hence leading to new ideas and incentives for the following stages in the copper production cycle.

Jan 1, 2015

By L. Alan Weakly

Global warming is a political reality in the United States today. The actual impact of the continued utilization of fossil fuels is not known and is open to debate. However, the growing concern about the continued use of these fuels is problematic. There are technologies available to us today that would permit America to meet its future energy demand and not contribute to global warming. The inconvenient reality is that fossil fuels cannot completely be replaced with energy conservation and the use of wind, solar, hydroelectric, geothermal and nuclear energy. The connection between the greenhouse effect and global climate change was first identified by physicist John Tyndall in the 1860s. To prove the greenhouse hypothesis, Roger Revelle and his research team started measuring carbon dioxide concentrations in the earth?s atmosphere in the early 1960s (Becker, 2007). With the rising concern about global warming, scientists throughout the world have been obtaining surface and air temperature data. Scientists have also been comparing CO2 concentrations found in glaciers throughout the world with theorized annual temperatures. Data for both dates back 1,000 years. Armed with this data, many nations of the world and the United Nations Intergovernmental Panel on Climate Change (IPCC) have concluded that climate change is a reality. The IPCC also concluded that this climate change is the result of mankind?s consumption of fossil fuels and that catastrophic consequences will occur on a

Jan 1, 2008

By Jörn M. Seitz

Dynamic load testing is employed with ever increasing frequency to estimate the strength and elastic settlement behavior of piles of all types. For dynamic loading ram masses up to 20 Mg have been used and pile resistance forces up to 30 MN have been activated. Strains and accelerations induced by the impact are measured near the pile top and a load-set curve is computed by the so-called CAPWAP method. This paper briefly describes both the necessary equipment and other details of the dynamic tests and the available analytical tools for data interpretation. Furthermore the need for further research and the current status of standardization will be discussed. This paper also presents the results from several static and dynamic correlation tests on cast-in-situ piles of up to 2 m diameter and 64 m length. The results demonstrate the economical and technical feasibility of this test method.

Jan 1, 1987

By Brajendra Mishra, Mark L. Strauss, Gerard P. Martins

Nearly the entire worldwide production of europium is recovered, as a minor constituent, from mining bastnäsite, monazite ore, or ion absorbing clays. However, this research indicates a process to recycle europium from waste lamp phosphors as a strategy meet the demand for europium. In this process, waste fluorescent lamp powder is retorted, sieved, leached, and precipitated to produce a mixed europium/yttrium rare earth oxide (REO). Europium is separated from yttrium by selectively reducing Eu(III) to Eu(II) using zinc powder and precipitating europium (II) sulfate from solution using sulfuric acid. Screening experiments were conducted observe the effect of pulp density, precipitation time, entrance pH, and stoichiometric ratio sulfate upon the grade and recovery of europium (II) sulfate. The best conditions to maximize grade and recovery of europium (II) sulfate were a 1 h precipitation time, 10 the stoichiometric ratio of sulfate, 100 g/L mixed REO, and the entrance pH equal to 3. The maximum grade of europium sulfate was 95.93%, and the maximum recovery was 73.32%.

Mar 1, 2018

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By K. E. Harley, M. J. Whiting, T. J. Sabin, E. M. Ryan, J. F. Watts

"Wire and Arc Additive Manufacturing (WAAM) has the potential to enable a very significant reduction in buy-to-fly ratio compared to conventional manufacturing through the ability to build near-net shape components. Components manufactured from AA 2319 by WAAM can exhibit significant levels of porosity. There is also a variation in the physical appearance of the surface deposit sometimes found on such components. This deposit is similar to those observed on aluminium joined by MIG and TIG welding processes. It has been suggested that both the bulk porosity and the surface deposit are caused by hydrocarbon-based lubricant on the feedstock wire. An established correlation between surface deposit and porosity would offer valuable insight into WAAM products and enable early interventions in quality control or process monitoring based on visual examination. The relationship between the nature of the surface deposit and porosity has been studied for AA 2319 WAAM components manufactured using different wire batches. Evidence is presented to support the assertion that (i) there does not appear to be a relationship between surface deposit coverage and porosity, (ii) batch-to-batch variability in feedstock wire affects porosity. This study has led to a better understanding of the cause of porosity in WAAM components.INTRODUCTION There is a high cost associated with conventional, subtractive manufacturing because of the high ‘buy-to-fly’ ratio, a measure of the initial material bought compared to the material found in the finished part (Allen, 2006; Yilmaz & Ulga, 2016). A typical aerospace product may have up to 90% of the purchased billet of forging machined away which is cost inefficient and high in material waste. Wire and Arc Additive Manufacturing (WAAM) has the potential to reduce costs and lead time. Robotically controlled weld torches rapidly deposit feedstock wire in layers to build large near-net shapes with mechanical properties similar to those of conventional manufactured parts (Sequeira Almedia & Williams, 2010; Martina et al., 2012; Ding et al., 2015; Williams et al., 2015). A high level of porosity variation has been observed in aluminium WAAM parts (Cong, Ding & Williams, 2014; Gu et al, 2016) which can result in a range of material properties (Rudy & Rupert, 1970). This leads to difficulties in regards to standardisation and qualification of process and parts. In order for WAAM to be used commercially, porosity will need to be understood, monitored and reduced to a reproducible acceptable level or eliminated."

Jan 1, 2018

By Maria I. De Rosa

The Bureau of Mines performed experiments to determine concentrations of toxic gases and liquids, and smoke-particle diameters and diameter-concentrations evolved during degradation of PVC-derived brattice with and without nylon-woven fabrics, fiberglass, cotton, and jute brattices, and other mine materials. The samples were exposed in a 20-L chamber at temperatures of 1500 to 4500 C, with a chamber airflow of 10 L/min; 27.3 cm3/s of which was directed into a submicrometer-particle detector-analyzer. During the degradation of PVC-derived brattice, large concentrations of hydrogen chloride (TLV, 5 ppm; STEL, 100 ppm) evolved at a temperature as low as 2000 C. The minimum toxic load of 3.1 mg or 40 ppm in 50 L of dilution air, with O.l~g weight loss, may be reached at a mine face with 314,000 L of dilution air, at the 5th min, during which less than 1 kg of brattice undergoes combustion. Fiberglass, cotton, and jute brattices, pine wood dust, and coal dust showed small concentrations of carbon monoxide evolving during early stages of combustion. Hydrogen cyanide gas evolved from the PVC-derived, nylon-reinforced brattice; at a later stage of combustion, large concentrations pf carbon monoxide and dense smoke evolved from all PVC-derived brattices. Experiments to characterize smoke particles showed that marked differences exist in particle diameter-concentrations among the materials.

Jan 1, 1986

By B. L. Gibbs

Computers have been used in the minerals industry for about 30 years and, in a few cases, longer. With the explosion of microcomputing during the past 10 years, computers have changed how many minerals producers go about their work. What computer usage trends are active in the minerals industry today, and what can we expect in the future? In general, computer usage is accelerating. Engineers and geologists are becoming increasingly "application literate." Soft¬ware is increasingly oriented to how people work. User interfaces have improved, so most users need to know only a mini¬mum of system commands and structure to work with a computer. Most industry professionals know how to use word processing and spreadsheet pro¬grams. AutoCAD appears to be the drawing program of choice. One reason is availability of training and add-on programs for earthwork, mapping, contouring, etc. Another frequently cited reason for using CAD is the ability to quickly make changes to a map or design, as compared to hand methods. Management is moving toward greater acceptance of computer usage. Computers do not need workman's compensation ... even though they may get sick and take a few days off! Computer hardware used in most minerals-producing companies is strongly personal-computer based and likely to remain so. The 486 personal computers are inexpensive as compared to workstations and provide the power and speed to run most applications in minerals industry engineering offices.

Jan 1, 1994

By Ken Pill, Jennifer Nyman, Liz Moran, Keaton Belli, Chelsea Bokman

The Moab Uranium Mill Tailings Remedial Action (UMTRA) Project Site (Site) is a former uranium-ore processing facility near Moab, Utah, where production ended in 1984. The United States Department of Energy Office of Environmental Management (DOE-EM) is responsible for remediating the site to meet 40 Code of Federal Regulations (CFR) 192 standards promulgated by the United States Environmental Protection Agency under the authority of the Nuclear Regulatory Commission (NRC). Tailings from the former mill were stored in an unlined impoundment (tailings pile), totaling 16 million tons of waste material. Surface cleanup has been ongoing since 2009 and consists of removal and transport of tailings via rail to an off-site disposal facility in Crescent Junction, Utah, with an estimated completion date around 2029. Gravity-driven migration of tailings fluids and recharge through the tailings pile and former on-site ore storage areas in the northeastern part of the site led to contamination of site soil and groundwater. The primary contaminant of concern is ammonia, which was present in fluids used in the milling process (DOE 2003). Uranium is a contaminant of potential concern. An interim groundwater remedy is currently in place that utilizes a system of extraction and injection wells to limit discharge of contaminated groundwater into the nearby Colorado River. Exceedance of surface water standards for ammonia are a principal concern due to potential endangered species fish habitat areas along the Colorado River adjacent to the Site. When necessary, surface water diversion is used to lower surface water ammonia concentrations when suitable habitats develop for endangered young-of-year fish. Once surface cleanup concludes and the tailings pile is removed, a formal groundwater remedy must be selected and documented in a Groundwater Compliance Action Plan (GCAP). Under Title 1 of the Uranium Mill Tailings Radiation Control Act, natural flushing (i.e., monitored natural attenuation), may be selected as the groundwater remedy if it can be demonstrated that the remedy will achieve groundwater standards within 100 years. The 40 CFR 192 groundwater standard for uranium is 44 micrograms per liter (μg/L), and the target groundwater concentration of ammonia based on adverse effects on local fish species is 3 milligrams per liter (mg/L). A collaboration with Geosyntec Consultants, Inc. (Geosyntec), the Moab UMTRA Project team, the DOE Office of Legacy Management, the DOE-EM, and the Network of National Laboratories for Environmental Management and Stewardship was held in 2022 with the goal to generate actionable recommendations to develop a GCAP for the Site. The primary recommendation was development of a groundwater fate and transport model to predict the remedial timeframe under various groundwater remedies. This paper presents the results of soil and groundwater sampling, geochemical modelling, and laboratory column and batch reactor testing that will be used to parameterize a numerical model for estimating the remedial timeframe under various scenarios, including natural flushing.

Feb 1, 2025