Search Documents

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By J. L. Young

The McLaughlin Mill started operating in January, 1985. For the first eighteen (18) months start-up, initial operation, and circuit debottlenecking have been done. The mill was designed to recover gold from a refractory ore requiring acid autoclaving pretreatment. This paper discusses the problem associated with bringing this complex hydro-metallurgical plant to consistently achieve design tonnages. Also, briefly described are the mill flowsheet, training program, permitting, and process and project development.

Jan 1, 1987

By Paul F. Kerr

The insufficiencies of our mineral resources are becoming well known, and the national political conscience seems to be troubled at last by our dependence upon mineral commodities which must come from other lands. This realization places increased responsibility upon the industrial, educational, and governmental groups whose task it will be to solve the problems of mineral supply. As we all know, from the time that man first sought mineral deposits until recent years, prospectors have been largely responsible for mineral discoveries. Today the era of the prospector is almost over. The human ants that have literally examined all accessible outcrops and have tested the gravels of nearly all stream beds in the United States have left undiscovered few worthwhile mineral deposits within the scope of their recognition. The pages in the history of mineral exploration are now being turned from the era of the surface prospect to the era of the hidden de- posit.

Jan 1, 1949

By J. -P. Saindon, L. D. Nel, A. E. Hall, S. G. Hardcastle

"This paper reports on an investigation into gas and dust concentrations in Ruttan Mine's exhaust air. The values obtained indicate that there is excellent potential to recirculate approximately 25% of the hot exhaust air into the intake air to reduce winter heating costs. Contaminant concentrations vary significantly during the course of the working shift and decrease in the mine exhaust system as the air returns to surface. A proposed on-line control system is outlined which would permit recirculation to be implemented with a pay-back period of less than two years. IntroductionIncreased energy costs and depressed mineral prices have resulted in mines, which use winter ventilation air heating, reviewing their systems to try to reduce costs. Heating costs can be significant, for example, Potash Corporation of Saskatchewan spends an average of $580,000 per mine per year and Ruttan mine spends approximately $IM per year on propane for its direct-fired heating system.Several method s of reducing heating costs have been considered and the following have potential application.Heat Exchange Between Exhaust andIntakeThis is usually accomplished by run-round glycol systems. The system is limited by ice formation on the coils in wet exhaust air and by the low exhaust air temperature, usually l0ºC. It also requires close proximity of the intake and exhaust airways to ma~e the cost of the connecting pipeline and pump systems economic . A feasibility study by Inco's Thompson operation reported that a proposed system of this type had a 19-year payback period and was, therefore, uneconomic. Potash Corporation of Saskatchewan is currently investigating plastic heat exchangers for a trial system because of corrosion on metal exchangers. It has the advantage of a 17°C exhaust temperature and relatively dry exhaust air.Waste Heat ReclamationThe waste heat from compressors and hoists can be used for heating in some mines. The feasibility of such a system depends on the individual layout and the proximity of the heat source to the inlet airway. Other mines have considered using the exhaust air in greenhouses to provide a cash crop."

Jan 1, 1988

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By L. J. Friedman

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric ?acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design _to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators, The current? design offers improved' impurity scrubbing along with increased reliability. in addition, a number of alternate gas cleaning systems have been offered Chemetica LAB System; Monsanto DuPont D:Jna-Wave Syatem1 Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems. _

Jan 1, 1992

E. Windsor Richards, London, England:—In reading this paper the most interesting point to me mas the question of the maximum percentage of phosphorus allowable in the steel rail. Mr. Colby said, and we will all agree with him, that the engineer knew, and even a steel-rail maker grants that phosphorus is the most undesirable constituent of steel. We in England have been for a long time considering a specification for the supply of steel rails. This matter has been taken up by the Institution of Civil Engineers, the Mechanical Engineers, the Iron and Steel Institute, the Institute of Naval Architects, and the Electrical Engineers. Committees have been formed,and the whole matter has received most careful attention. They arrived at last at an analysis which I will read: " The carbon is to be from 0.35 to 0.5 per cent.; the manganese from 0.7 to 1.0 per cent.; the silicon, not to exceed 0.10 per cent.; phosphorus, 0.07; and sulphur, 0.07 per cent." As to the phosphorus, which is the most important point of all in the analysis, we have for many years, and indeed until very lately, always agreed to supply steel which would not contain above 0.06 per cent. of phosphorus. Iron-ores are not quite as good now as they were formerly, and the manufacturers at the meetings of the committees referred to, tried to obtain an increase in the allowance of phosphorus. They asked the Sub-committee to agree to 0.08 per cent. of phosphorus. They tried all they possibly could to obtain that; but they failed. English engineers in Great George Street and all over England, representing the important Associa tions I have mentioned, would only agree to 0.07 per cent. and that is the maximum allowance of phosphorus. Mr. Colby is an able advocate, but with all his ability he would not have been able to persuade the English engineers to agree to 0.08 per cent.

Jan 1, 1907

By G. E. Murray

Introduction The development of the method for recovering zinc from lead blast-furnace slags at Trail is interesting and important in the history of both lead and zinc metallurgy. Many efforts have been made in the past, particularly in Germany, to make economic recovery of zinc from slag. The Pape process on Oker slags was successful and is being worked at the present time. More recently the Waelz process has come to the fore. One effort at Cockle Creek, Australia is of special interest in view of subsequent developments. This was re-ported in detail by Guy Courtney in 1920(1). It deserves mention as it shows how, as in many other instances in the metallurgy of lead and zinc, important pioneering work has been done in Australia. These experiments, started over 25 years ago, comprised reduction with coke, powdered coal, and eletrothermically in carbon-lined furnaces. The so-called slag eye furnace, which volatilised the metals from a blast furnace running with a hot top, was also investigated.

Jan 1, 1933

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By H. S. Duzgun, N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline’s long-term availability, to develop preventive maintenance plans and to make future projections about the dragline’s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, Page 736 and Marion 7820, which have been operating in the Tunçbilek openpit coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data and (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (15.29 m3) seemed to be more reliable and less likely to fail when compared with Marion 7820 (30.58 m3). The operating hours without failure range from 41 to 51 hours with 50% reliability.

Jan 1, 2011

By Carl R. Christiansen

The primary objectives of this project are (1) the determination of manpower demand in primary lead and zinc production for the years 1985 and 2000, and (2) the estimation of the availability of the required manpower for these years. In order to meet the first of these objectives relationships between employee requirements and metal production in the various states were established, The total primary lead and zinc production from United states mines in 1985 and 2000 has been predicted by the U.S. Bureau of Mines. These forecasts and the 1974 figures are as follows: [1974 1985 2000 Lead metal, tons 669,000 700,000 900,000 Zinc metal, tons 494,000 585,000 995,000] Mining By analysis of ore reserve data and industry characteristics, the authors estimated the portion of the primary production which each state would yield in the future years. As manpower requirements are determined by the tons of ore produced and by worker productivity, these figures were determined for each mining state and district by developing relationships between lead and zinc metal production, ore production, ore to recoverable metal ratios, employee productivity, and number of employees required. The number of new employees required annually to compensate for attrition and production growth is provided, also.

Jan 1, 1975

By Angelina Anani, Nilufer K. B. Akbulut, Sefiu O. Adewuyi

Crucial information about safety, design and operation from ground movement data can be utilized in underground mines. Communicating the information and exploring new findings can be a challenge, however, in a decade where there is an ever-increasing volume and velocity of data due to advancements in mining technologies. This challenge escalates for geotechnical data as they are multidimensional, depending on the space and the rate at which they take place. To tackle this challenge, geotechnical engineers should focus on using simple yet compelling visualization of rock mass data in 3D. Competent visualizations of ground conditions as a trigger action and response plan (TARP) could ease the communication of safety concerns and the exploration of rock mass displacement and strain surrounding an opening at an underground mine. Therefore, this study focuses on using scientific visualization methods by rendering geotechnical data over the surface of a 3D mesh model to display TARP levels. The study was conducted at the East Decline of the San Xavier (SX) Underground Mine, a laboratory mine operated by the University of Arizona. The project aims to produce visualizations that optimize the use of geotechnical data in near-real time.

Sep 1, 2025

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

By S M. Stewart

Industry, especially extractive industry, must now give serious attention to the impact its operations have on the natural environment and on the economic, social, and cultural context within which it operates.   While this obligation is statutorily managed, there has been a recent shift towards a culture of self responsibility. Industry is now talking about earning its ôsocial licence to operateö and the importance of maintaining the ôtriple bottom lineö, thus adding environmental and social performance to the usual financial criteria used to measure organisational performance. The social context within which companies operate has also become more sensitive with industry responding to a growing public expectation that it conduct itself in a way that strives for sustainability by operating and developing in a way that meets the needs of the present without compromising the ability of future generations to meet their own needs.   There are glowing accounts of industries engaging and collaborating with the communities within which they are based. In amongst these are also some disasters which result from cultural assumptions, industry created dependencies and the failure to attain community buy-in despite significant investment by the industry involved.   There are also remarkable stories of communities, and action groups within communities, being a significant catalyst for positive change of their natural, cultural and social environment. In amongst these stories there are also accounts of long and drawn out battles; adversarial situations where no one wins; a litany of mistrust, tricks and tactics, with the better resourced party ultimately achieving its primary objectives at the cost of the other (and at the cost of any potential fruitful, mutual relationships).   So what makes the difference in achieving the positive rather than negative outcomes? The answer lies in the way the outcomes are achieved. Building relationships based on good communication, respect for divergent views, mutual understanding, and the development of trust and empathy, makes it possible to identify shared goals and objectives that best meet the needs of all parties.   Research indicates the mining industry is making good progress in developing policy and commitment to community development and engagement but that, ætranslating commitments into improved practices at the site level remains one of the industryÆs toughest challengesÆ. (Australian Government - Community Engagement and Development Handbook October 2006 @ page 49.)   This paper considers the merits of a process of community collaboration and what it has to offer in terms of meeting that challenge.

Jan 1, 2007

By D Hillier, A Giblett, K Parker, V Ramsell

Kalgoorlie Consolidation Gold Mines (KCGM) operates the Kalgoorlie Super Pit open cut, Mt Charlotte underground mine, Fimiston process plant and Gidji Roaster facility for joint venture partners Newmont Mining Corporation and Barrick Gold. In 2004, the Fimiston plant was upgraded by the addition of gravity concentration to the Fimiston and Mt Charlotte grinding circuits, including the installation of a central intensive cyanidation reactor to process the gravity concentrates. The gravity project was justified after detailed analysis demonstrating an expected increase in overall gold recovery of approximately one per cent, in addition to reduced elution costs and reduced gold inventory in flotation concentrate stockpiles. The gravity circuits were commissioned in August 2004, and have since consistently recovered 10 to 20 per cent of the gold present in the KCGM ore, delivering a reduction in coarse gold losses equivalent to 0.45 per cent additional metal recovery and contributing to improved metal accountability.CITATION:Giblett, A, Hillier, D, Parker, K and Ramsell, V, 2012. The impact of gravity gold recovery at Kalgoorlie Consolidated Gold Mines, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 199-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By G. Richards Gwinn

In modern warfare, mica is truly indispensable. Coordination of combatant units necessitates maintenance of intricate communications equipment, in the construction of which high-grade sheet mica is essential. Scrap, ground, and the poorer qualities of block mica, which are less essential to the military program, are not considered in this paper. Furthermore, as the paper is designed primarily to assist mica miners, mica derivatives, Such as splittings and films, also are excluded from discussion. The paper therefore relates solely to block mica of strategic quality. Understanding of t e many factor involved in marketing mica is definitely advantageous to mica, miners. The nature and detrimental effects

Jan 1, 1943

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

This manual provides basic practical instruction on the inspection of driven piles. It covers the essential components of pile driving, such as the pile driving hammer, hammer accessories, the pile and soil, and frequently encountered test methods in an uncomplicated, yet knowledgeable, and practical manner. Insight is given into the methods of installing the foundation, dealing with the cranes which do the lifting, the hammers which do the driving, the leads that guide the hammer and pile, the compressors which provide the external power when required, and finally prevalent analysis tools and testing instrumentation and procedures which enable you, the Inspector, to do your job. This DFI Inspector's Manual for Pile Foundations will help the Pile Inspector who has limited knowledge of pile foundations. Perhaps this Inspector has been pressed into service at a moments notice; a few helpful hints and suggestions to him are desperately needed and he can look here for the basics. It is also useful for the experienced Pile Inspector as a reference guide. However, this manual is not a detailed check list of every possible scenario and detail which could ever be encountered. There are other sources available which give more detailed descriptions (and should be consulted by the Inspector when appropriate; a list of this additional reference material is provided and suggestions made in appropriate chapters of this text). The current manual is more a brief "textbook overview" with some of the more important aspects given at least some emphasis so that the Inspector has some direction and hopefully helps to produce a safe, yet economical, foundation.

Jan 1, 1997

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

By H. K. Najarian

AT Josephtown, Pa., on the south hank of the Ohio River about thirty miles northwest of Pittsburgh, is the Josephtown electrothermic zinc smelter, which operates as a custom smelter receiving both domestic and foreign concentrates. Constructed in 1930, the plant was designed to produce zinc oxide and to process 124 tons per day of zinc concentrate obtained mainly from the Company's New York State mines. Zinc condensing equipment was developed in conjunction with the St. Joe electrothermic. furnace and commercial production of zinc metal started in 1936. Expansion of the plant and equipment during 1939 and 1940 brought the processing. capacity to upwards of 300 tons of concentrate per day; and the plant operated at peak capacity during the war years, earning the Army-Navy "E" award and three subsequent stars. A postwar plant expansion is now under way, designed to increase the capacity to 500 tons per day of concentrate, with an estimated daily production of 160 tons of zinc metal of various grades, about 100 tons of zinc oxide, and 425 tons of sulphuric acid as major products.

Jan 1, 1947