Search Documents

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By C. S. Ek

Tests have been performed to recover silver and lead from residues produced after a super-hot leaching in a zinc hydrometallurgical plant operating with jarosite precipitation. When this residue is leached in ammoniaammonium sulfate or in diethylenetriamine solutions, lead dissolution is not complete and its recovery from the aqueous solutions is either difficult, due to the operating conditions, either expensive due to the amount of added reagents. In both cases, silver is partly dissolved, partly left in a new residue still containing lead and baryum sulfates. The best treatment seems to include a selective flotation producing first a silver concentrate assaying about I % Ag, then a 50 % lead concentrate collecting the baryum salts, and a final quartz-gypsum tailing. Metal recoveries can reach 50 % and 80 %, respectively.

Jan 1, 1989

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper is devoted to ultrafine grinding of processing products. This process allows one to include into operation complex ores which earlier were considered as inefficient and economically inadvisable to treat. Fine dissemination of valuable component often does not allow its liberation via standard grinding in ball mills, and therefore requires modern methods of ultrafine grinding (UFG). An example of successful ultrafine grinding usage is its application for crude flotation concentrates regrinding before cleaner flotation stages. A problem often arises with a commercial copper concentrate production in the course of copper ore flotation. Crude flotation concentrate regrinding in a ball mill does not provide for good liberation of the material before cleaner stages. UFG application allows one to get commercial copper concentrate with copper grade of 20% and higher. Another example of ultrafine grinding application is its usage for highly refractory pyrite product received after gold-lead scavenger flotation of polymetallic ore. Earlier this product treatment was economically inefficient. At current application of ultrafine grinding down to 85% minus 20 µm and subsequent gravity processing it is possible to pass major part of gold (73.4%) into concentrate. The constraining factor for UFG application in processing may be the chemical activation of minerals. In the result of this, flotation selectivity may decrease. Therefore ultrafine grinding application extends the areas of efficient usage of metallurgical processes. New technologies allow increasing the level of valuable metals recovery."

Jan 1, 2014

New Zealand's Land and Income Tax Act 1954 contains unique incentives for companies engaged in mining certain specified minerals or petroleum. Sections 152 and 153 provide for the taxable income of such companies to be based not on profits made but on dividends paid to shareholders. A significant saving in tax results, particularly where profits are not distributed: but the Act attempts to ensure that undistributed profits are used for further mineral exploration and development. To encourage investment in the mining industry, persons taking up shares in a company mining for the specified minerals or petroleum are entitled to a one-third deduction in respect of monies paid on the shares and used by the company for its purposes; and company shareholders may make loans to the company and write-off such loans for tax purposes to an amount of up to half their taxable income. Maximum utilisation of the tax incentives calls for careful consideration as to whether a mining or petroleum company should be financed by way of loan capital or share capital.

Jan 1, 1971

By Sneyd R. J, Walton M. C

In early 1987 Minproc acquired a license from the inventor to engineer and construct acid plants incorporating the Fattinger technology. The process offers a simple and reliable method of producing sulphuric acid from metallurgical off gases at significantly lower capital and operating costs than the more familiar contact process. The process also offers the simultaneous production of nitric acid, if the NOx content of the off gases is high enough. A development of this latter process has other applications within the minerals industry, particularly in conjunction with refractory gold ore preoxidation.

Jan 1, 1989

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a longwall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

By B. C. Darst

Developments in the agricultural use of potassium (K) have been based solely on the essential role K plays in crop production. Crop plants cannot complete their normal life cycle if K is deficient or absent. In fact, no essential plant nutrient other than nitrogen is required in greater quantities. Table 1 shows the amounts of K some crops take up from the soil. Although the exact functions of K in the plant are not well known, its primary role seems to be tied to plant metabolism. Potassium is vital to the process of photosynthesis. When K is deficient, photosynthesis declines, but respiration increases. These two K-deficient conditions. . . reduced photosynthesis and increased respiration ... lower the plant's carbohydrate supply, the end result being poor agronomic crop production. Potassium is also essential to several other plant functions, including the following: 1) Protein synthesis. 2) Water use efficiency, through the influence of K on stomata opening and closing, to maintain the turgidity in plant leaf cells. 3) Translocation of heavy metals such as iron and zinc. 4) Ionic balance. 5) Control of enzyme reactions within plants.

Jan 1, 1985

By Mirza Muhammad Zaid, Nana A. Amoah, Ping Chang, Guang Xu, Ashish R. Kumar

The key takeaway of this study is the significant improvement in dust protection for roof bolter operators in underground coal mines. The optimized canopy air curtain (CAC), with a redesigned two-level manifold system, provides uniform airflow distribution that effectively reduces dust exposure. By enhancing the protection of operators from harmful respirable coal and silica dust, this technology can reduce the risk of diseases such as coal workers’ pneumoconiosis (CWP) and silicosis. The application of this optimized CAC design in real-life coal mining operations can dramatically improve worker health and safety by minimizing dust-related exposure, ensuring compliance with industry regulations and prolonging the lifespan of mining equipment by reducing dust accumulation.

Dec 1, 2024

By J. F. Magee

THERE is nothing new about drag-line dredging for placer gold. The use of the separate unit for excavating preceded the large barge with bucket-line excavator mounted upon it, which has developed to a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant to work economically the shallower gold gravel deposits that the bucket-line dredges do not work. The dragline dredge consists of the drag-line excavator, on caterpillar mounting on the edge of the dredging pond, which feeds the gravel to the washing plant, mounted on a floating barge in the pond. There have been more than twenty-five such plants built and operated in central and northern California and an unknown number in other States. There have been variations in details of design but the essentials are similar in all. I wish to describe the operation of a typical drag-line dredging plant, that of the Wyandotte Gold Dredging Company on the Farnan Ranch in the Oroville district. This organization of six active partners built their first plant on Wyandotte creek in the autumn of 1933. The operation was successful due to wise management, which was based upon good plant design and proper principles of operation. The partners elected one of their number, H. F. England, as manager with full control and responsibility. This plant and operation furnished the pattern for many subsequent ones.

Jan 1, 1937

By Donald A. Bruce

"Abstract The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.In the BeginningIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2014

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By Youze Xu

The leaching and reduction of Cr(VI) in soils contaminated by chromium-containing slag were investigated with column experiments. The results showed that Cr(VI) concentration in leachate decreased from 988 mg L-1 to 407 mg L-1 after 7 days when water was used as leaching agent. However, Cr(VI) in leachate in culture medium treatment was not detected at above periods. In comparison, Cr(VI) concentration in leachate from autoclaved soil remained 398 mg L-1 at the end of experiment. The results indicated that the indigenous microorganism was capable of reducing Cr(VI). The amount of Cr(VI) reduction was 335 mg at the whole experiment period and the reduction rate was 67.09 mg d-1. Carbon supply showed minor effect on Cr(VI) reduction. However the reduction capability of Cr(VI) could be improved by combination of the carbon and the nitrogen. The optimal quantity was 5 g L-1 of yeast extract and 4 g L-1 of glucose.

Jan 1, 2009

By L. C. IlsLey

In January, 1922, a conference relative to trailing cables for use with permissible mining machines was held at the Pittsburgh Experiment Station of the U. S. Bureau of Mines. At this conference it was recommended that the bureau take steps to investigate the rubber-sheathed type of cables and to bring about the establishment of a list of approved cables. Effective until such time as a complete investigation could be made, the bureau asked the several manufacturers holding approvals for mining machines to recommend cables for use with their machines. In general the cables recommended were tentatively approved. Due to the lack of available personnel, no actual tests of cables were made until mid-1927. Meanwhile a field investigation of trailing cables was made at 20 mines of three coal companies in western Pennsylvania, and samples of cables were obtained from the manufacturers for laboratory tests. Twenty-five samples of the concentric-type cable, representing the product of five manufacturers, were obtained for the tests. These cables were of four sizes, as follows: 3 cables of No. 2 B & S gage, 17 cables of No. 3 B & S gage, 3 cables of No. 4 B & S gage, and 2 cables of No. 6 B & S gage.

Jan 1, 1929

Despite the research interest on non-cyanide gold lixiviants over the past three decades all the non-cyanide gold processes are still at the developmental stages with limited understanding on solution and pulp chemistry in some cases. This is partly associated with:the difficulties in measuring reliable equilibrium data for various gold(I/III) complexes with non-cyanide ligands; the lack of knowledge on mixed-ligand complexes; and different kinetic stabilities of gold(I) complexes with respect to disproportionation. This paper presents reliable equilibrium data for complex formation, dissolution, precipitation, hydrolysis and disproportionation reactions of gold(I/III) compounds with a range of non-cyanide ligands: S2-, HS-, S2O32-, SO32-, SCN-, SC(NH2)2, OH-, NH3, Cl-. Solubility of gold(III) compounds with non-cyanide ligands follows the order: Cl- > NH3 > OH-. In the case of gold metal the solubility order at a given temperature is MgS > Fe(III) or Cu(II) / Cl- > Cu(II)/NH3 > NaOH, but the solubility increases with increasing temperature. Rate of gold oxidation with different non-cyanide lixiviants depends on the oxidant, ligand and temperature and follows the general order of oxidants: Fe(III) or Cu(II) > X2 or OX- > O2 (X = halogen). In the case of metal ion oxidants oxygen is required to reoxidise Cu(I) or Fe(II). Some of the reported data on chloride and thiosulfate leaching of gold are presented to highlight the effect of additives and the copper, silver and sulfur contents of the starting material on the success of non-cyanide leaching processes.

Jan 1, 2004

By Y Peng, D Liu, S Vink, B Wang

There have been strong industrial observations that clay minerals have a deleterious effect on mineral flotation grade and recovery. However, rigorous explanation on the role of clay minerals in flotation and effective ways to reduce their negative effects are not available. In this study, the flotation behaviour of low quality and high quality coal samples were examined at the Xstrata Oaky Creek Coal plant, and laboratory in fresh and recycled water with high ionic strength. Anionic and non-ionic dispersants including lignosulfonates and triblock copolymers were also tested with an objective of improving coal flotation in recycled water. It was found that overly stable froth was produced in the flotation of both low quality and high quality coal samples in saline water. Speciation modelling indicated precipitation of hydrophilic components which may adversely affect the flotation. Despite the overly stable froth, saline water produced much higher combustible recovery than fresh water without significantly losing the product quality. Lignosulfonate dispersants displayed a potential to improve the flotation in fresh water, but not in saline water. Significant flotation improvement was achieved with the triblock copolymer examined in both fresh and saline water.CITATION:Liu, D, Wang, B, Peng, Y and Vink, S, 2012. Determining the effect of clay minerals on coal flotation using saline water, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 151-158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Friedrich Benthaus

"The natural and man-made realities on either side of the Atlantic are different. Therefore, a large part of the other side' s knowledge and experience cannot be transferred easily. In the following, the author will attempt to describe some of those developments in the German hard coal industry which may be of particular interest to readers on this side of the Atlantic.The area of the Federal Republic is quite small, especially if compared with a country as large as Canada. On a territory the size of the maritime provinces of New Brunswick and Nova Scotia, Germany holds coal reserves roughly corresponding to the total Canadian reserves. More than 20 billion tons of hard coal down to a depth of 1500 m, and more than 30 billion ton s of brown coal of lignite are technically and economically extractable acording to current technology.However, not only are Germany's coal resources more concentrated; the country is also densely populated, and there are dense networks of railroads and highways All components of the so-called infra-structure are available everywhere, be it electricity, any machinery or personnel. Public opinion is likely in favour of an increased utilization of coal.The coal industry is well developed through a long evolution covering centuries. As a consequence, there is an effective and intensive cooperation of numerous bodies and institutions concerned with coal mining, from government agencies including the inspectorate to suppliers, trade union s, producing companies, to jointly operated management and research organizations. In the Federal Republic, hard coal is mined in deep mines only, and lignite in general, only from open-cast pits. There is a complete organizational and geographic separation of hard and brown coal in Germany. Because the Federal Republic holds only insignificant mineral oil and very little natural gas deposits, coal is essentially the only and consequently the most valuable source of energy."

Jan 1, 1984

By Tom Skodack

Mine and tunnel contractors face a complex environment-one in which economic risks are high, operating costs grow ever higher, ore grades are lower or recovery more difficult, and civil construction projects are intensely competitive on a world-wide scale. Within the context of this environment, the risks and rewards of proper machine selection for rock excavation have become proportionately large. Speed, depth and scope of analysis, and extensive supporting information are indispensable in the selection process. Equipment designs and their applications are also myriad and diverse. Several equipment alternatives and excavation techniques may have to be evaluated at once to choose the most cost-efficient approach. The following examples are typical of the current demand for more detailed equipment analysis: • An aggregate supplier starts a new quarry. He knows his targeted tonnage, blasting restrictions, and previous operating costs from other quarries. But he must improve on his old costs. What drill pattern, hole size, and bench height will give lowest cost per ton? How many crawler drills and what type will produce this tonnage most efficiently? • A mine is using a fleet of twin pneumatic ring drills for long hole drilling to initiate their cave. The mine is facing both air shortages and increasing operating costs with decreased efficiency in the ring drill fleet. If they invest in new hydraulic long hole drills, what impact will each drill unit have on production? Each twin drill unit? What configuration gives best operator efficiency and subsequent reduction in manpower? Which configuration gives the best return on investment? • A tunnel contractor is bidding a long straight water tunnel by conventional drill and blast methods. What is the optimum number of drill booms for the tunnel cross section and excavation schedule? How many rounds per day can he achieve? What are his total project drill, blast, and muck costs? In the past, such questions could be answered, but only approximately at best. One good prediction could involve many hours of laborious calculations that had to be repeated each time a new parameter was introduced or an existing parameter changed. In 1980, increasingly complex analysis, coupled with increasing need and quick response times demanded by industry, led Atlas Copco's project department to turn to the computer. New computer programs based on theoretical considerations and three decades of worksite performance data were developed for evaluating mine and tunnel contractors' equipment needs, productivity, and partial or total operating cost calculations for most conventional drill and blast excavation techniques-including shot rock loading and transportation. This Computerized Analysis of Rock Excavation-or CARE-program has since been available to the mining and construction industry. From each program specific results can be pre- dicted, including: • Productivity Calculations-Rock drill penetration rate for a given drill, hole size, and rock type, optimized for the best drill steel life; net machine productivity (drill-out time or drill meters-footage-per shift); total drill round time, including charging, blasting, loading, and haulage; suggested drill pattern, computer printed, including hole size for a given rock drill, rock type, and associated blasting restrictions for either drift rounds or benching applications; long-hole drill meters (ft) per drill shift; breasting down (upper drilling) drill meters (ft) per drill shift; and comparison between continuous loading machine capacity and LHD capacity. • Operating Cost Calculations-Operating costs expressed as cost per drill meter (ft), cost per cubic meter (cubic yard) of excavated rock, and cost per meter (ft) of tunnel advance. These costs may be calculated using as many cost centers as the mine, quarry, or tunneling contractor wishes. Specific operating costs may cover drill rig operating costs only, less capitalization; drill rig operating costs, including amortized equipment investment; drilling and blasting costs; drill, blast, load, and haulage operating costs; long-hole drilling operating costs per drill meter (ft) or per blasted cubic meter (cubic yard) of rock; and loading and transport operating costs. In all the above cases, any number of cost and capacity calculations may be run by simply changing important cost center variables to judge their net effect. Accuracy as a Function of Input Data and the Statistical Data Base Accuracy of a projection clearly depends heavily on the data base from which the projection is drawn.

Jan 11, 1982

By F. Ajersch, M. Rigaud, M. Jallouli

"Le gonflement des boulettes d'hématite à été étudié à l'aide d'une méthode de mesure standard ISO ainsi qu'à l'aide d 'une méthode de mesure dilatométrique.La première méthode a servi à l'étude des boulettes haute silice (5% SiO2) dont l'indice de basicité (IB = CaO + MgO -i- SiO2 + Al2O3) a été ajustée soit à l'aide d'une addition de dolomie, soit à l'aide d'une addition de pierre à chaux, soit à l'aide d'une addition de ces deux composes. L'indice de basicité variait de 0.05 à 0.12. Les résultats de gonfle ment obtenus à 1000?C dans une atmosphère de 40 CO - 60 N2 ont permis de montrer qu’indépendamment de l'indice de basicité c'est la dolomie qui contribue le plus à diminuer le gonflement par rapport à la pierre à chaux. L'utilisation de l'indice de basicité comme critère de sélection des boulettes est discutée.La méthode dilatométrique a servi à l'étude du gonfle ment de deux types de boulettes préparées à partir de deux concentrés de fer et dont la teneur en silice a été fixée à 2.5% et 0 5%. Ces deux types de boulettes ont reçues les mêmes additions de liant en quantité et en nature. La détermination en continue du gonflement, à 950?C dans 40 CO - 60 N2, a permis d'une part de mieux cerner le niveau de réduction auquel correspond le maximum de gonflement et d'autre part de montrer que l’allure des courbes de gonflement est étroitement liée à la nature du liant. Une augmentation de la teneur en silice des concentres contribue à diminuer le gonflement des boulettes.Des essais de réduction de gonflement non isothermes ont été réalisés à des montées de température à 10 et 20?C/min. Les résultats indiquent que le gonflement déterminé dans les conditions non iso thermes est inferieur à celui obtenu lors des essais isothermes. On discute alors de la validité des essais standards de gonflement qui sont utilisés pour prédire le comportement des boulettes lors de leur réduction dans un haut fourneau."

Jan 1, 1983