Search Documents

By R. S. Warfield

The Kasna Creek copper deposit near Lake Kontrashibuna in the Lake Clark region, Alaska, was the object of an investigative project by the Bureau of Mines during the fall of 1948. Recessed because of inclement weather, it was completed in 1949. This project was a part of the Bureau of Mines program in Alaska for the development of critical and strategic minerals. The ore bodies are contact-replacement deposits in limestone. Mineralization is mainly specular and micaceous hematite associated with chalcopyrite, calcite, chlorite, quartz, and amphibole. The deposit, on the right limit of Kasna Creek approximately 2 miles from the shore of Lake Kontrashibuna, is composed of two mineralized zones that range in altitude from 2,350 to 2,650 feet. This report contains a brief history of the prospect, description of the physical setting of the property, its geology, and the factual results of the Work performed by the Bureau of Mines.

Jan 1, 1951

By N. D. Cristescu

The aim of the present paper is to show how a mathematical modeling of a creeping rock and that of an yieldable lining can allow us to obtain an optimization of the lining design and generally of the whole procedure and sequence of excavation-lining application. We follow the procedure presented by Cristescu (1989) Chap. 13, and Cristescu et al.(1987); for some other approaches see the literature mentioned, for instance, by Ladanyi and Gill (1988). We have in mind to describe the creep of the rock, i.e. the tendency of the tunnel to close in time, and to take into account that the lining itself may be deforming, i.e. possesses some rheological behavior. We start from the well known fact that "intelligent" lining, which are yielding to the pressure of the rock, may be much more successful in supporting creeping rocks than excessively strong, badly designed supports which are unable to resist to pressure of the rock, though these are oversized supports (too strong, too stiff, installed too early, etc.). In order to optimize the lining to be used for a certain rock, it is absolutely necessary to study in the laboratory the main mechanical properties of that specific rock and to formulate for it a reasonably simple mathematical model. Standard triaxial test results are quite enough to determine the model for the rock, combined with some creep tests which have to reveal the long-term behavior of rock (the so-called rheological model). What concerns the lining, we consider several kinds of linings existing today, for which a mathematical model was also formulated. One shows which is the interaction between the creeping rock? and the yielding lining and how can it be formulated in mathematical terms. Once written in mathematical terms, an optimization of the lining design and that of the excavation layout and support application sequence is possible. We will try to make the exposure as simple as possible, avoiding details and having in mind to give only a sketch of the problem, while the mathematical details could be worked out quite easy.

Jan 1, 1994

By Barton G. Stone

The mining and exploration industries have been using Geostatistics (Matheron, 1963) for the past forty years. It has been extensively incorporated into three dimensional block modeling software whose usage has reflected the growth in the use of personal computers since 1980. Because of the utility of geostatistical models in mining and production planning, much of the modern reserve and resource modeling is done by mining engineers, geostatisticians and geological engineers. Explorationists are initially less concerned with three dimensional models until such time as a deposit has been roughly delineated. However, the concept of regionalized variables in ore deposits deals with the effect of spatial correlations between data points in a three dimensional sample space and should be useful for optimizing the spacing of drill holes to allow maximum bang-for-the-buck in drilling programs. This paper examines three common deposit types (porphyry copper, VMS and intrusive gold) to examine whether geostatistical methods have been used to minimize drilling costs because of better understanding of spatial correlations. The three model types were chosen from publicly available corporate websites of Canadian based Junior Mining Companies. They include the Wolverine polymetallic zinc deposit of Yukon Zinc in Yukon, Canada; the El Morro Deposit in Chile (30 percent ownership by New Gold Mining Company, and the Fort Knox Gold deposit in Alaska and 50 percent ownership by Nova Gold Resources). Typically, individual mining corporations post their technical reports as CNI 43-101 reports on their corporate website as indications of the favorability or progress on their more exciting properties. Data considered for this paper was not collected or generated by the author, but the information was extracted from these publicly available sites and had a variety of authorship.

Oct 1, 2009

By Frank B. Gilbreth

The problem of the crippled soldier in industry is not a problem of war work only; it is a problem of industrial development. As individuals, each one of you is seeking to provide our maimed heroes with such teaching as will render them, in the shortest possible amount of time, productive and satisfied members of the community. As individuals you are interested in the organizations that are preparing to receive these men, to train them and to place them at that work for which they are best fitted. As an organization, it is now your duty to take up the industrial end of the problem, to investigate existing conditions in the industries, to discover where the opportunities for employment lie, and so readjust industrial practice that the cripples may be utilized to their own and the community's good with the least shock to themselves or to the industries, and with the greatest amount of permanent benefit to all concerned. We have divided industrial opportunities suitable for cripples, roughly, into three classes. First, such as already exist in the industries, which can be set aside for cripples only, present occupants being transferred to other work for which they can be fitted but which is not suitable for cripple work; second, opportunities in the industrial world that, through changes in the working equipment or tools, or through appliances attached to the cripple himself, can make the cripple a competitor of the sound worker; third, opportunities not existing at present in the industries, but which could be introduced for the good of the community without placing the cripples into competition with any existing class of workers. As typical of the first type of occupations for cripples, we have mentioned that of store-keeper, of the second type that of typist,2 and of the third type that of dental nurse.3 The last occupation can be so arranged as to take from the overworked dentist the work of cleaning teeth; and

Jan 1, 1918

By H. J. Wasson

With the close of 1932 and the third year of the depression, the activity of oil production presents, amidst the general wreckage and chaos of industrial society, a somewhat unique picture of rationalized economic effort. How long it will continue to present such a picture, however, is a subject for conflicting surmises. East Texas still dominates the contemporary horizon, but it has become, at least for the time being, a definitely known factor. With its 9500 wells it is approximately 90 per cent drilled up. So long as production control obtains, it is merely one important factor of the national oil reserve. Domestic Production The notable new discoveries in the United States were less numerous than for several years. Elsewhere in the world the record is much the same. The Conroe field in Montgomery County, Texas, lying in an intermediate zone that might be classified either as Gulf Coast or East Texas, represents perhaps the single example of a truly major discovery during the year. Elsewhere in Texas the new pool discoveries, about a dozen or so in number, were nearly all in the region known as Southwest Texas. Oklahoma contributed seven or eight new pools of the routine "run-of-mine" caliber, and the opening up of a few deeper oil pays also were of some significance. Continued expansion of the proved and semiproved reserves in Kansas added an important increment to the oil resources of that state. In California not a single new field was added to the roster, though deeper pay zones equivalent to or of greater importance than many new fields in other parts of the country were discovered or indicated. The new deep zone in the Belridge field is considered by some to underlie the prolific Temblor and may thus forecast the widespread distribution of a potentinl oil horizon underlying many San Joaquin Valley fields below the depths thus far exploited. Aside from the routine operations in connection with settled production, the Eastern fields were decidedly inactive. Further new develop-

Jan 1, 1933

By W. P. Lass

Discussion of the paper of W. P. LASS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 103, July, 1915, pp. 1443 to 1447. ROBERT M. KEENEY, Somersville, Conn. (communication to the Secretary *).-There is not only a possibility of improvement in present methods of treatment of the byproducts of refining in the cyanide plant by the use of the electric furnace, but also in melting and refining of gold precipitate. This interesting paper by Mr. Lass shows an electric furnace in successful operation in a large plant for the treatment of by-products. Electric melting of cyanide precipitate is a cheaper form of treatment in many cases than any of the combustion methods now used because of the high cost of oil, coke or coal in many camps, while on the other hand electric power may be had cheaply, especially in a place where there is possibility of development of high-head hydro-electric plants for power purposes. Also, if the oil-fired tilting furnace is used for direct melting of the precipitate, as is the case at many small mills, a great saving in cost is made by the use of the electric furnace because of the high crucible cost in melting with the tilting furnace. A study of this paper indicates the cost of the operation approximately. Consider all the fluxes to be turned in as byproducts and coke at $18 per ton.

Jan 12, 1915

By Peter Townsend, Sergei Diachenko, Allan Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30,000tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors; in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400m causing a major failure of the northwest wall involving close to 100Mt of waste material.

Jan 1, 2006

Many sampling standards arrive at a value for the prescribed sample mass by assuming a specific relation between the sample mass and the relative standard deviation of the fundamental error and assigning a value to the tolerated coefficient of variation. In order to obtain an equation that provides a relation between the minimum sample mass and the particle properties, many different models for the drawing of a sample have been developed. Here, a model for the drawing of a sample is proposed which can be considered to be a generalisation of the model used in GyÆs sampling theory. Using simulations, it is illustrated that the generalised model can lead to a better correspondence with actual sampling processes.

Jan 1, 2005

By M. Soleymani Shishvan

"Continuous mining systems containing multiple excavators producing multiple products of raw materials are highly complex, exhibiting strong interdependency between constituents. Furthermore, random variables govern the system, which causes uncertainty in the supply of raw materials: uncertainty in knowledge about the reserve, the quantity demanded by the customers, and the breakdown of equipment. This paper presents a stochastic-based mine process simulator capturing different sources of uncertainties. It aims to quantify the effect of geological uncertainty and its impacts on the ability to deliver contractually defined quantities and qualities of coal, and on the system efficiency in terms of utilization of major equipment. Two different areas of research are combined: geostatistical simulation for capturing geological uncertainty, and stochastic process simulation to predict the performance and reliability of a large continuous mining system.The process of modelling and simulation in this specific production environment is discussed in detail. Problem specification and a new integrated simulation approach are presented. A case study in a large coal mine is used to demonstrate the impacts and evaluate the results in terms of reaching optimal production control decisions to increase average equipment utilization and control coal quality and quantity. The new approach is expected to lead to more robust decisions, improved efficiencies, and better coal quality management.IntroductionContinuous coal mining systems containing multiple excavators producing multiple products of raw materials are highly complex and exhibit strong interdependencies between constituents. A network of conveyor belts is used for transportation of the extracted materials to different waste dumps or the coal stockpile.Optimal decision-making in short-term planning and production control are impacted mainly by geological uncertainty associated with incomplete knowledge of the coal deposit represented in the reserve block model. These uncertainties cause deviations from expected process performance. For more robust decision-making, understanding the impacts of these stochastic elements plays a key role."

Jan 1, 2016

Timestudy analysis of mining operations at North Broken Hill Limited has been carried out by dissecting operations into small elemental components, and accurately timing these elements. Over a wide range of observations, this has enabled standard time values to be calculated for all underground work.The application of the standard values is in calculating performances as a measure of work output and Performance Controls are kept on approximately two-thirds of underground employees. Through the Controls it has been possible to stimulate supervisory action to improve low performance, and to reduce delays and lost time.The values are used to calculate contract" prices, and anomalies in previous prices have been adjusted on work values and not on arbitrary standards. In out-of-the-ordinary circumstances, the request for a timestudy investigation has been made by both operatives and foremen, and the contract set following the timestudy analysis has been to the satisfaction of both parties.The range of values enables contracts to be applied to work which was previously performed on a day basis, resulting in improved performance.A natural corollary of timestudy is the analysis of methods, and in some cases method improvements have been introduced.It is anticipated that further investigations will be made on methods.INTRODUCTIONIn 1953, a Timestudy analysis of mining operations at North Broken Hill Limited was commenced under the guidance of management consultants. Its aim was, to determine standard time values for specific operations, which would provide management with a measure of productivity beyond the existing measures of tons or feet of advance, and also to determine whether increased output was available under existing operating conditions.

Jan 1, 1956

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By Kurt Oakes, John Williams

Placer Dome, US operates the Bald Mountain Mine. The Bald Mountain Mine is a surface operation located in remote northwestern White Pine County in east-central Nevada, approximately midway between Elko and Ely. The mine is in the Newark Valley along the southwestern flank of Bald Mountain a part of the Ruby Mountain range, at an approximate elevation of 7,500 ft (2,286 m). The geology at the Bald Mountain Mine is highly altered, both mineralogically, and structurally. Highwall stability and control have long been an issue at the operation, due largely to the varying geologic conditions. In some blasts as many as seven distinct geologic unconformities exist. These unconformities affect both final high wall integrities, as well as blast fragmentation characteristics. A 60 million ton (54.5 million tonnes) layback expansion of the existing “Top Pit” as well as development of a new satellite pit, “Sage Flats”, is being undertaken. Design final highwall pit slopes have been steepened from the traditional 47º to 55º in order to reduce overall ore-to-waste ratios, thereby improving economic viability for the expansion over the 4.5 year life of the project. With the increased usage of electronic detonators throughout the mining industry, mine operations staff, as well as representatives from the mines explosive supplier felt that an evaluation program incorporating electronic detonators would be warranted. The areas of focus for this evaluation would be resultant highwall pre-split integrities, peak particle velocity measurements (both near field and far field), frequency measurements, loader productivity, and visual interpretation of the results. The mine incorporates 25 ft (7.6 m) benches and uses separate trim blasts in conjunction with production blasts in order to reduce blast effects along final highwalls. Hole diameters in production blasts are 7? ” (200 mm). Typical production blast patterns are 18 ft x 18 ft (5.5 m x 5.5 m), drilled in a square pattern configuration. Shot sizes vary greatly, ranging from 200 holes to as many as 800. Bulk low percentage ANFO/emulsion blends are utilized as the redominant blasting agent. Non-electric dual delay detonators (25 ms/500 ms), with non-electric surface delays are the initiation system utilized in production blasts. Typical production blast design

Jan 1, 2004

By Charles B. Kenahan

Vanadium is subject to only light corrosion in phosphoric acid at temperatures up to 60° C. and has a moderate corrosion rate in this acid at 100° C. It is relatively corrosion resistant in sulfuric and hydrochloric acids up to 60° C, but corrodes rapidly at 100° C. It corrodes rapidly in dilute nitric acid at 35° C. Vanadium is almost inert in 10-percent solutions of formic, acetic, lactic, tartaric, and citric acids; in 9-percent oxalic acid it corrodes slowly up to 60° C. and rapidly at 100° C. Vanadium is resistant to corrosion in substitute ocean water, tapwater, and in 3-percent sodium chloride and 10-percent sodium hydroxide solutions. It is readily attacked, however, by 20-percent ferric chloride, 20-percent cupric chloride and 5-percent mercuric chloride solutions. Vanadium is protected by contact with magnesium, aluminum, and steel SAE 4130 in substitute ocean water, by magnesium and aluminum in 3-percent sodium chloride solution, and by magnesium in tapwater. Vanadium protects copper in substitute ocean water. When vanadium and stainless steel are coupled in sulfuric acid solutions, both metals are usually unaffected by contact, whereas the corrosion rate of titanium in sulfuric acid is greatly reduced by contact with vanadium.

Jan 1, 1962

By Qingjun Zheng, Robert Vasinko

Cladding by plasma transferred arc (PTA) welding is widely used for enhancing the surface properties of a metallic component, in particular wear, high temperature and corrosion resistances. This paper presents the application of Kennametal Stellite PTA cladding technology, especially the DuraStell PTA process technique, for tungsten carbide composite cladding for boiler tube application. DuraStell PTA process gives low heat input to the substrate and fast deposition rate. The cladded boiler tube samples showed more uniform carbide dispersion in the cladding, less base metal dilution, and insignificant effect on the microstructure and mechanical properties of the substrate base metal, in comparison of the traditional PTA and other arc welding process.

Mar 1, 2017

By R. B. Walker, R. Palmer, L. C. Bryner

The purpose of this investigation was to further study some of the factors affecting the air oxidation of sulfide minerals. Data obtained from laboratory studies on the effect of temperature, concentration of iron salts, pH, and other catalysts on the biological and nonbiological oxidation of sulfide minerals are presented. The oxidation of copper sulfide minerals and subsequent leaching of the soluble copper has long been a profitable operation. The chief oxidizing agent is oxygen from the air. This reaction is influenced by a number of different factors such as temperature, light, hydrogen ion concentration, oxidizing agents, and various catalysts. Sullivan1 found that copper sulfide minerals are slowly oxidized by the air and that dilute sulfuric acid and iron (111) increased their solubility. At that time it was not known that bacteria were involved in the oxidation of the sulfide minerals. It has been shown that pyrite, molybdenite, free sulfur, and the copper sulfide minerals found in the waste rock dumps in Bingham Canyon, Utah, are largely oxidized by chemosynthetic autotrophic microorganisms found in the leaching streams.2-6 Similar organisms have been isolated in other mining areas7,8 and from the effluents from coal rnines.9 The following are some of the questions that have arisen regarding the mechanisms of the reactions involved in the leaching process. How dependent is the leaching operation upon the biological reactions? How does the temperature effect the biological and non-biological reactions? How does the concentration of iron (II) and (111) effect the rate of oxidation of copper (II) sulfide? Does the iron act as a catalyst? Does activated carbon act as a catalyst on the oxidation of sulfide minerals? What effect does the hydrogen ion concentration (pH) have on the above reactions? The purpose of this paper is to report the results of laboratory studies on these problems. EXPERIMENTAL The apparatus used in this investigation was an air lift percolator described in our earlier work.' The percolator consisted essentially of an air lift which enabled the leaching solution and microorganisms to pass freely through a suspension of mineral (substrate) in Ottawa sand. The air lift served the additional purpose of maintaining an ample concentration of oxygen and carbon dioxide in the nutrient (leaching) solution. (See Fig. 1.) The percolators were so constructed that they could be immersed in liquid constant temperature baths for temperature studies. The thermostats were controlled to +0.5°C. The reactions were all run in the dark. The percolators were charged with one to three g of mineral, dispersed in 100 g of Ottawa sand and 100 ml of nutrient or leaching solution. The sand was purified to remove traces of iron by digesting with concentrated hydrochloric acid and washng with distilled water until free from chloride. After drying, the sand was ready for use. The compressed air supply was regulated to 5 psi and bubbled through an aerator containing distilled water, which was maintained at the same temperature as the bath used. The air was filtered through cotton plugs to maintain sterile conditions. The tops of the

Jan 1, 1968

By Gjergj Dodbiba, Toyohisa Fujita, Li Pang Wang, Masashi Yamane

"The platinum-group metals (PGMs), are currently receiving worldwide attention as they have major industrial uses. PGMs, i.e. ruthenium (Ru), rhodium (Rh), palladium (Pd), osmium (Os), iridium (Ir), and platinum (Pt), are widely used as catalysts in petroleum and chemical processes. In addition, they find wide applications in automotive exhaust-gas control converters and are of immense importance to the electronic industry. Broadly speaking, PGMs are extracted in minute quantities from a limited number of ores, found mainly in South Africa and Russia. As the PGMs are both costly and almost indestructible, they are usually recycled from various forms of scrap. In other words, the recycling of the PGMs is an essential factor in the overall management of the PGM economy. In addition, the ever-increasing user areas have created renewed interest in the search for new sources or deposits of PGM, which in turn requires an in-depth knowledge of its characteristics. In this work, the emphasis is placed on the need to analyze the composition and microstructure of blast-furnace slag for recovering PGM metals. In other words, chemical composition, surface analysis and microstructure analysis of the DC arc furnace slag have been carries out. The aim is to provide a detailed analysis of this material for anyone with an interest in gaining further knowledge of its specific content for recovering PGMs."

Jan 1, 2014

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012

By B. C. Peterson

Calumet Division, Calumet & Hecla, Inc., whose operations are in Houghton and Keweenaw Counties, Mich., is a highly integrated and complex organization. This division operates mines, a railroad, a concentrating mill, a reverberatory smelter, and the auxiliary generating plants and shops to service these operations. In addition, it operates a sands reclamation plant, leaching plants, a foundry, and a machine shop that serves varied industries with castings and parts for many applications. Calumet & Hecla, Inc. has produced over 60 percent of all the copper that has been produced in Michigan since discovery of the ore in 1864, and in 1959 the company ranked eight among the country's producers with a production of 17,407 tons. To keep abreast of modern accounting systems developed elsewhere in industry and to combat increasing costs due to higher labor and supply costs, as well as increased costs due to deeper mines and lower grade ore, the company has developed a modern machine cost accounting system. This not only provides the usual bookkeeping and cost accounting facilities but offers accurate cost data for engineering evaluation of the mining operation. This system is credited with being instrumental in permitting continued operation of these high-cost mines in a period of increasing costs with no corresponding increase in the price of metal.

Jan 1, 1962

By Guo Junfeng

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst, and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas. This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012