Search Documents

By S. S. Yu

In this paper, the producing process of using V2O3 as raw material to obtain vanadium nitride was analyzed through the means of thermodynamic. The analysis shows that conversion follows the principle of reduction step by step in the conversion process of V2O3. The temperature of the reaction system has prominent influence on the nitrogen content of products, and the reaction is very sensitive to temperature. As raising temperature, the fine grain structure of the nitrides is more evident, and the grain size of nitrides increases. At 1703K, the nitrogen content of the products tended to be constant after soaking over 3 hours.

Jan 1, 2014

By A. J. Mcintosh

PRICE changes in competing fuels in the last three decades have reflected the changes in the consuming habits of the people of the United States. Prior to World War 11 the importance of fuel oil and fuel gas increased almost constantly while the relative importance of both bituminous and anthracite coal decreased. During this same prewar period coal prices increased to a much greater extent than oil prices. In fact, in many years, oil prices declined and in most cases are now no higher than they were back in 1925-26. During the war natural economic trends were entirely upset because of the tremendous petroleum requirements of the Army and Navy. Under these conditions many industrial plants were converted to the use of coal and the new installations in home heating and industrial plants of all kinds which might have used oil were practically eliminated. Although petroleum prices were rigidly controlled by OPA coal prices increased several times during the war. An over-all statement as to the rela-

Jan 1, 1947

By A. Ingelson

Conflict over mineral development and its impacts on indigenous peoples occurs in many countries around the world. Canada, Bolivia and Peru have experienced mine development for centuries in areas where indigenous communities have been and continue to be affected by the mining industry. On a global basis the mining industry continues to face the challenge of implementing meaningful consultation programs with indigenous peoples. Many governments around the world have adopted sustainable development as a policy and one important element of sustainable development is minimizing social conflict. John Moffet and Francois Bregha (Moffet & Bregha, 1996), in their analysis of the role of law reform in promoting sustainable development, noted that stakeholder participation can reduce this type of conflict. Social conflict can result in expensive litigation and costly project delays for mine developers. Meaningful consultation with indigenous peoples in areas where mine development is proposed can be a critical factor in securing a social licence to operate. A report released by the United Nations in 2005, outlined the elements of a concept called ?free, prior informed consent? (FPIC) that promotes more sustainable development. FPIC provides that mineral exploration and mining should not proceed unless the mining company has secured the consent of the relevant indigenous group(s). This paper employs a comparative approach to evaluate the extent to which three active mining nations, Canada, Bolivia and Peru, require consultation with indigenous residents and adhere to the principle of FPIC. The comparative approach assists in the identification of those consultation elements in the legal regimes of each country that can minimize social conflict in mineral exploration and mine development and therefore contribute to more sustainable development. First, we examine the legal requirements to consult with and accommodate indigenous communities in Canada, a country with a long history of mineral development over a large geographic area that has entrenched in its Constitution the protection of indigenous peoples? rights. We then turn to an analysis of Bolivia, one of the most indigenously conscious mining jurisdictions that has followed the Canadian lead in entrenching constitutional protection for indigenous peoples. Third, the approach to consultation with indigenous peoples in Peru, a nation that has not adopted the Canadian and Bolivian approaches to constitutional protection of indigenous peoples rights, is considered.

Aug 1, 2013

By Fred W. Gordon

The North Chicago Rolling-Mill Co., of Chicago, have four furnaces at South Chicago, built during 1881. Each furnace is 20 feet diameter of bosh, and 75 feet total height, the hearth being 11 feet diameter, and the top 15 feet 4 inches. They are blown through seven 7-inch tuyeres placed 5 feet 6 inches above the hearth level. Cubical contents, 15,000 cubic feet. Each furnace is supplied with 2 blowing engines, 84-inch blowing cylinder, and 36-inch steam cylinder, and 54-inch stroke. These two have one jet-condenser worked by an auxiliary pump. The blast for each furnace is heated by the aid of three Whitwell fire-brick stoves, each 21 feet diameter and 60 feet high. In the batteries of boilers furnishing steam for four furnaces there are 36 double-length boilers, 76 feet long, 48 inches diameter and 16,000 square feet heating-surface. The plant was designed to produce 3600 tons per week, or 900 tons for each furnace, and was fitted as above with such engines, boilers, and hot-blast stoves as were thought requisite for that production ; hence, calculated from the present make—not the least remarkable feature is the economy of construction—there are less engines, less boilers, and less hot-blast power for the iron made than at ally plant within my knowledge, or it could to-day be duplicated for less money per ton of iron made per week than could any plant now in existence, whether using fire-brick or cast-iron stoves for heating the blast. This is a practical demonstration of my assertion in a paper on fire-brick stoves, read before the Institute," that the application of fire-brick stoves in construction really lessens the first cost. In view of the statements just made, I must be most emphatic in assuring the members that nothing is strained or overburdened.

Jan 1, 1886

By J. M. Ross

THE Homestake mine is situated in Whitewood mining district, in the northern Black Hills of South Dakota, in the city of Lead, Lawrence County. The entire property, comprising 557 lode claims with a total area of 3343 acres, is held under United States Patent. The older claims were 300 by 1500 ft. under local regulations, the newer ones 600 by 1500 ft. The Homestake was discovered April 9, 1876, by Moses and Fred Manuel, and Jake Harney, who were drawn into the northern hills, from the Custer placer district, by news of the discovery of rich placer deposits in Deadwood Gulch. They located a number of additional lode claims and, in a short time, the whole country was covered with locations. The Manuel brothers built an arrastre the following winter and took out $5000. The next year the Homestake lode was sold to Senator George Hearst and associates, who organized the Homestake Mining Co. Other companies were formed to exploit other groups of claims and at one time five companies were operating on this deposit, the Father DeSmet, the Deadwood-Terra, the Caledonia, the Highland, and. the Homestake Mining Co. These companies, however, have been merged into the Homestake Mining Company. The first stamp mill, known as the "Eighty Mill," commenced operation on July, 12, 1878, and production has been nearly continuous since that time.

Jan 2, 1925

By J. S. Ll. Leach, J. B. Cohen, M. B. Bever

IN the work reported here, the heats of formation of a copper-rich Cu-Sn (a) solid solution and of the Cu.Sn (0 phase were measured by tin solution calorimetry. An approximate determination of the heat effect attending the precipitation of 6 from a supersaturated a solid solution was also made.

Jan 1, 1955

By Kumar M. Lyer

The channel reactor for ferrous and nonferrous processing has been modeled as a combination of ideal reactors. Cold model studies simulated the counter-current flow of slag and matte (or metal) with high-strength submerged gas injection. A composite model has been developed which describes the mass transfer between the two liquid phases, including the transfer of minor elements. The residence time for the matte droplets in the matte/slag emulsion is compared with the settling rates for the matte droplets in the slag to determine their relative importance in the mass transfer between matte and slag. The governing equations for mass transfer have been developed using correlations for the mass-transfer coefficients in the continuous and dispersed phases. An application of this scheme to a typical copper smelting system is presented.

Jan 1, 1993

By H. Fechtig, R. H. Buck, A. G. Guy

MULTIPHASE diffusion has been studied for many years in two-component systems1,2 and many of the experimental aspects are now fairly well understood.314 Although by no means all of the problems connected with the two-component case have been solved,' attention has recently been directed to the more complex situation involving three components. The pioneer work of Clark and Rhines6 yielded a qualitative picture of the types of behavior that can occur, and Clark7 has suggested conventions for describing the various phenomena. Kirkaldy and co-workers8,9 have made quantitative studies in several ternary systems and have offered explanations of the occurrence of isolated and nonisolated precipitates. At present, however, there is no comprehensive theory for the variety of phenomena observed in ternary, multiphase diffusion. By analogy with several studies that have been made of multiphase diffusion in the binary Cu-Zn system,2'10'11 a similar exploratory study was made of Cu-Zn-Ni alloys lying along the line in the ternary diagram from the point 80 Cu-20 Ni to the zinc corner of the diagram, Fig. 1. A principal question to be answered was whether initially plane interfaces would remain plane during the course of one-dimensional diffusion. The diffusion specimens studied are described in Table I. The five separate alloys from which they were made were melted in evacuated Vycor capsules from 99.9 pct purity copper, zinc, and nickel. Since some of the alloys were too brittle to be swaged, all of the alloys were used in the cast condition. To facilitate later homogenization, the molten alloys were solidified by plunging the capsule in water. Homogenization heat treatment was done at 720°C for 20 hr. The five nominal compositions in weight percent zinc and nickel, respectively, were: 37.5, 12.5; 44.0, 11.2; 50.0, 10.0; 55.0, 9.0; 65.0, 7.0. Ln Table I the alloys are identified only by their zinc content. Sandwich-type diffusion specimens were prepared by pressure welding disk specimens, each about 3 mm high by 10 mm in diameter. Welding was done in a special threaded vise which was heated at 500°C for about an hour in an atmosphere of flowing hydrogen. A measurement of the separation of the phase interfaces was made on a polished flat on the welded specimen, and then the specimen was sealed in an evacuated capsule and given the diffusion treatment shown in Table I. The diffused specimen was sectioned longitudinally

Jan 1, 1965

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002

By Nikolaos Polysos

To drive and utilise gate roads economically requires accurate planning and risk assessment considering the variable geomechanical requirements. The geomechanical part of roadway planning is secured by geotechnical investigations of drill cores and geophysical borehole logging. The rock specific parameters determined in this way allow a statement about the quality (defomtation and strength characteristics) of the rock that has to be cut across. They set up the basis for a standardised rock assessment. Combined with the prevailing rock mechanical situation, technical boundary conditions for advance and support techniques can be identified already in the planning phase. Detailed geotechnical investigations prior to the planning and driving of roadways can lead to a technically and economically optimised roof support system. Geotechnical core logging and a standardised assessment scheme based on the data acquired will be introduced. Geophysical borehole logging methods provide additional physical data. Different methods and their validity, which may lead to a further improvement of the planning reliability, will also be presented. The geomechanical information gained and their relevance fir the planning will he illustrated. Keywords: rock classification, geotechnical rock parameters. geophysical well logs. support planning

Jan 1, 2002

By Lee Barbour

Waste-rock piles from metal mining operations are comprised of large surface deposits of unsaturated, coarse-grained soil and rock. The unsaturated condition and heterogeneous, coarsegrained nature of these deposits make them difficult to monitor or characterize. Key parameters that must be evaluated include; volume-mass relationships (e.g. water content, air content, porosity, density, degree of saturation, grain-size), transport properties (e.g. air-permeability, gas diffusion, hydraulic conductivity), geochemistry (e.g. solids, gas, and fluid phases) and soilatmospheric fluxes (water and gas). This paper describes some of the techniques that have been developed to characterize waste rock piles for uranium mines in Northern Saskatchewan. For each technique, the method of measurement is described, and preliminary field data are presented and discussed.

Nov 1, 2002

By Sadi Medina

As it is characteristic from Custom Smelters, ENAMl Las Ventanas Smelter has to deal with different qualities and quantities of mining products from about 70 suppliers, that contain a variety of impurities that would be harmful for copper production. In order to increase the smelting capacity, an oxygen plant has been running since September of 1990. Moreover, to improve the environmental conditions, a new sulphuric acid plant started up to neutralize the metallurgycal off-gases from the Teniente Converter and partially from the Peirce-Smith converters. Based on the on-line operation among the reverberatory furnace and the Teniente Converter using oxygen enriched air to produce high grade matte, most of the volatilizing impurities, mainly arsenic, are collected as discarding compounds in the gas cleaning system of the acid plant. This paper describes the continuous performance of the Teniente Converter with acid plant, the results attained, the operation problems and how they were solved. The impurities distribution achieved in this process is also included.

Jan 1, 1993

By Adam J. Gesing

Eddy current separators are increasingly used by the auto shredder operators to produce higher grade of nonferrous metal concentrate for recycling. While this increases the unit price of the concentrate, metal losses through inefficient metal recovery quickly offset the price differential. We show how to optimize the eddy current separation system at the shredder to maximize mate- rial throughput, nonferrous metal recovery and grade of the nonferrous metal concentrate.

Jan 1, 1998

The steps for the beneficiation of iron ores differ from ore to ore, depending on the mineralogical phases of the particular iron ore and the nature of the association of the gangue minerals with iron oxide in that ore. The extent to which the beneficiation can be undertaken economically depends both on the amount and the nature of the gangue. The analysis of the phases present in an orebody optimises the mining and process operations (separation, beneficiation, sintering, etc).X-ray diffraction (XRD) provides qualitative and quantitative information about the main ore phases as well as the gangue mineralogy and the amorphous content present in a sample. In addition, modern quantification methods such as Rietveld refinement allow the calculation of the distribution of elements in solid solutions such the substitution of Fe with Al in goethite or hematite.The use of high speed detectors has made XRD an important tool for grade and process control. Finger printing of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. Grade control using XRD can be completely automated and controlled remotely.The two case studies in this paper demonstrate how XRD and finger printing can be used for grade control, process optimisation and quality control of a goethitic and a magnetitic iron ore. The enormous potential of XRD as an inexpensive, reliable tool, useful in the characterisation of iron ores will be demonstrated.CITATION:K÷nig, U, 2013. Application of x-ray diffraction to iron ores - potential implications for grade control and downstream processing, in Proceedings Iron Ore 2013 , pp 275-280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By L. A. Cornish, I. A. Mwamba, R. A. Couperthwaite

"In previous work by the authors, it was established that additions of 0.2 at.% Ru to an Fe-40 at.% Al alloy improved the corrosion and oxidation resistance of the alloy. The alloy was produced by mechanical alloying and spark plasma sintering and the work showed that nonequilibrium processing was able to significantly refine the grain size of the material. The sintered material had a higher hardness than the as-cast material and the change in grain size did not significantly affect the oxidation and corrosion. In the present research, the mechanically alloyed powder was coated onto a mild steel substrate using cold-spray coating at a gas pressure of 10 bar and a temperature of 500°C. The coatings were found to be 5–10 um thick, although thicknesses of up to 30 um were observed. The coated materials were subjected to oxidation and corrosion tests to determine the effectiveness of the coating in increasing the oxidation and corrosion resistance of mild steel. This was done to determine the effectiveness of cold-spray coating as a technique to coat these mechanically alloyed powders. IntroductionPrevious work conducted by Mintek (Couperthwaite et al., 2013, 2015) investigated the effect of precious metal additions on the structure, oxidation and corrosion properties of an Fe-40 at.% Al (Fe- Al) alloy. Initial work determined that additions of more than 0.5 at.% precious metal did not improve the oxidation and corrosion properties of the materials and in some cases even decreased the resistance to corrosion. Further work identified Pt and Ru as beneficial additions to the FeAl alloy. Four alloys were then produced by mechanical alloying and sintering (FeAl–0.2 at.% Pd, FeAl–0.2 at.% Ru, FeAl–0.5 at.% Ag, FeAl–0.5 at.% Pt). These alloys were all successfully produced by melting and casting and mechanical alloying sintering and it was found that the nonequilibrium processing greatly decreased the grain size of the materials compared to the ascast materials. It was found that the additions of Ru and Pt were still the most beneficial to the oxidation and corrosion properties, with Ru being considered the most beneficial."

Jan 1, 2016

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By Jing Zhang, Qing Xiao, Xulong Liu, Qiuju Li

"Pickling sludge generated from stainless steel production process contains large quantity of Cr, Ni, and Fe. The disposal of and fill sludge directly not only leads to the heavy metal dissolves in the soil and underwater, but also loss value metals. However, the major mineral phases of value metal are hydroxides and there are lots of calcium fluoride and water in the sludge. So the pickling sludge has to be pretreated before reduction-magnetic separation. The TG analysis, reduction reaction and magnetic separation were all used to study the pickling sludge. The result indicated that up to 900°C the total weight loss of pickling sludge was 22.32%. The mass contents of Fe, Cr and Ni in the tailings (non-magnetic) were 4.27%, 0.067% and 0.041% respectively.IntroductionSince 21st century, the stainless steel production in the world has been continuously increasing because of its excellent performance [1]. However, high stainless steel production means a high pickling sludge production. For example, in a stainless steel plant with waste water quantity of 100m3 /h, the production of pickling sludge will exceed 15 Kt/a. Pickling is essential for generating of a homogeneous and corrosion-resistant surface during stainless steel production subsequent process. Pickling of stainless steels is predominantly carried out with an aggressive solution, sulfuric acid H2S04 or composed of nitric acid HN03 and hydrofluoric acid HF [2]. During the pickling process, the pickling acids are recovered through ion exchange and metal ions such as Fe3+, Cr3+ and Ni2+ get into the acids forming the pickling waste water [3]. Then, the pickling waste water is precipitated with lime, forming pickling hydroxide sludge. It is not feasible to recycle or treat the pickling sludge using conventional methods, because the sludge has high contents of calcium fluoride and water but low contents of iron, chromium and nickel. However, it would also pose a potential environmental problem if deposited outdoors over a long term because it contains heavy metals such as Cr and Ni. At present, solidification/stabilization (S/"

Jan 1, 2014

By Jensen B

The approach of using the Coward Triangle for the analysis of flammable mine gas mixtures has been examined for its application, to the flammability of coal dust/gas/air mixtures. Explosible lean limit and rich limit concentration data for dust/methane/air mixtures are examined and illustrated using co-ordinate geometry. It is concluded that a three-dimensional envelope representing hybrid explosible mixtures can be drawn. The dimensions of this explosive zone will vary with the characteristics of the coal dust and the gaseous composition of the mine atmosphere. Further research is needed to establish these dimensions for important mined seams.

Jan 1, 1994

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By L. Kuzev

Unknown and unpopular vibrational grinding mills possibilities to horizontal working chambers have been discussed. They can be realized under normal conditions with the typical values of vibrations applied with vibrational grinding which are: vibration frequency from 15 Hz to 50 Hz, vibration amplitude to 6 mm and vibration geometry. These possibilities constantly increase involving new raw materials and processes. Vibration grinding is possible with other technological process accompanied by intensified technological processing, while the process decreases. In many cases these technological decisions are original.

Jan 1, 2014