Search Documents

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This article offers an examination of a retreat mining method conducted at the Pinoura Mine in India from 2010 to 2017. The method is atypical for coal mines of India’s coalfields. The method executes depillaring in a single pass and does not require the formation of galleries and support installation in splits, thus, reducing the cycle time. A variety of observations are discussed throughout this work and emphasis is placed on field measurements and depillaring under weak roof (RMR = 40–45). This paper discusses design techniques, specifically the estimation of the snook (remnant pillar) size, and important practical observations after the fact. The execution of this method was eventually conducted in eleven panels.

Aug 4, 2020

By J Kokado, N Hatta, S Yabushita

A theoretical model is described for prediction of the capacity of fines from porous ores, such as cokes and sintered ores, to be removed by a pneumatic, horizontal-type classifier prior to charging into a blast furnace. First, the influence of variation in the apparent density and drag coefficient of porous ores on removal efficiency is analysed from a stochastic standpoint. The effect on efficiency of collisions between particles in the classifying region is then examined analytically in relation to the ratio of the mass flow rates of particles and air (the loading ratio). Finally, a theoretical model is constructed that takes these factors into account. Theoretical and experimental results are compared and classifying efficiency is discussed from both experimental and theoretical viewpoints.

Dec 1, 1993

By W. P. Lass

(San Francisco Meeting, September, 1015) THE gold precipitate from the zinc-dust presses in the cyanide plant of the Alaska-Treadwell Gold Mining Co.; Treadwell, Alaska, is treated, in the refinery adjoining, by the Tavener or lead-smelting method. About. 3 or 4 tons of this precipitate are produced monthly having a gold assay value of $40,000 to $60,000 per ton. It was formerly the practice to treat the by-products from this process, consisting of 2 tons of slag, 300 lb. of matte, 500 lb. of refinery refuse, flue dust, etc., in a 24-in. water-jacketed blast furnace. This' practice was discontinued in the summer of 1914 by reason of the difficulty of keeping the lead-well open when treating a high-grade lead product; of preventing the loss of gold in the flue dust; and of avoiding injury to the general health of the refinery operators; a plain single-phase electric furnace was substituted for the blast furnace. The furnace was constructed from an old steel acid drum by cutting off the top and introducing a cable, made from strands of bare copper wire, through the bottom and spreading the strands out fan-shaped on the inside of the drum. Powdered graphite, obtained by grinding up old crucibles, mixed with 10 per cent. cement, was tamped wet into the bottom of the drum, around and completely covering the copper wires. The graphite was carried up to the bottom of the furnace, or lead-well, and acted as the lower electrode. The sides were built up of ordinary firebrick forming a melting chamber 14 in. in diameter by 20 in. high.

Jan 7, 1915

By G. Van Weert

In the spring of 2010 double refractory ores from historical stockpiles were processed through Barrick's Goldstrike pressure oxidation facility, thereby providing preg robbing feeds for a variety of metallurgical testwork. This paper describes the effects of amount, type, place and time of addition of activated carbons on CIL gold recovery and shows that native carbon in plant PDX'ed discharge solids can still preg rob gold loaded activated carbon.

Jan 1, 2011

By N. F. LeJeune, Earl C. Lane

This is the third of a series of reports on a survey of petroleum prod- ucts manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in the other parts of the United States, and the claim has been made that some of the present Federal Specifications for petroleum products tend to discriminate against Cali- fomia products. The purposes of the present survey are to determine what par- ticular specification requirements Califomia petroleum products characteristical ly fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what lines investigation to determine this question should proceed. The first report of the series gave the physical and chemical properties of the samples of gasoline and mineral spirits. A second report**, gave the physical and chemical properties of samples of lubricating oils. The present report deals entirely with burning and fuel oils. The refin ing companies have continued their very cordial and helpful cooperation. Seven samples of kerosene, four samples of Diesel fuel and eight samples of fuel oil were obtained. The methods of analysis used are those adopted by the Interdepartmental Petroleum Specifications Committee, published by the Bureau of Mines in Technical Paper No. 323. The specifications used for corparison are those officially adopted by the Federal Specifications Board for the use of the various Depart- ments and Independent Establishments of the Government, effective February 3, 1923, and published by the Bureau of Mines in Technical Paper No. 323, Part 1. Specific gravity, degrees A.P.I., viscosity and other special tests al- though not required by the specifications have been given for comparison. All temperatures are recorded in degrees Fahrenheit. Tables have been prepared giving data on physical and chemical propertios of the individual samples. Before each table the classification and specifica- tions for the particular class of oil considered in the table are given. Follow- ing each table, brief notes show wherein samples deviate from specification re- quirements.

Aug 1, 1923

æSustainabilityÆ is one of those words that has gained more usage in popular discourse than in the dictionary. In fact it is not in many dictionaries at all. Typically, given this, it also seems to mean different things depending on whose lips it emerges from. It is now like a code word in that if people say it, you donÆt have to think about its meaning; it is just æthereÆ and is taken for granted. This is a problem for the mining industry as we are now using the term too and to be effective in what we do, we need to have a reality check and see how those outside who have views on us (æstakeholdersÆ maybe) use it. The core issue seems to be æsustainability of whatÆ: the industry?, a company?, the global environment?, particular ecosystems?, the community? At these levels, the term seems almost meaningless. If we do not even agree on what it is, at least broadly, our communication and possible partnerships for going forward will be difficult to say the least. One reference to æsustainÆ in my thesaurus is: æTo keep from failing during stress or difficultyÆ. This may be a clue to something approaching a common notion. I suggest that to use æsustainabilityÆ we make the following assumptions:that we are talking about human activity aimed at making a living that has an impact on the natural and social environment; that humans must make a living (though what this needs to include is problematic); that the impact of particular activities has been problematic to date and needs to be monitored, altered, stopped, etc; that there is stress on both social and natural environments; and that change can be effected in order that particular activities such as mining minimise their negative effects and maximise their positive. This is why we are taking part in sessions such as this one today. Two more initial observations: First, it strikes me that even with the above assumptions laid out, æsustainabilityÆ and æsustainable developmentÆ are too abstract and general as concepts. We have to break these high and mighty ideals down into workable, bite-size chunks, into practical ways of dealing with the world outside our sites and companies. Second, sustainability, on both sides of the fence, too often focuses on nature and environment as though they are independent of people and community. I would argue, perhaps provocatively, that sustainability is primarily a people issue and has to be tackled as such. I want to look at the overall climate for business today and how it has responded before I return to what we can and need to do as the mining industry to make æsustainabilityÆwork.

Jan 1, 2002

By G. Vik, P. Chryssanthakis, S. C. Bandis, L. Haruik, N. Barton, M. Christianson, A. Makurat

The large jointed chalk reservoir situated at 3 km depth in the North sea's Ekofisk field is undergoing major compaction after nearly 15 year of oil and gas production. Approximately 150 km 3 of the overlying sediments, mostly shales, are involved in the subsidence. A maximum central subsidence of nearly 3 meters, and a maximum present rate of 45 cm per year has set in motion numerous studies of the phenomenon. Non-linear finite element (FEM) and non- linear distict element (DEM) analyses of the compaction and large scale subsidence were performed. Consistent differences between the continuum and discontinuum analyses were noted. In the latter, slip on hypothetical bedding planes and sub- vertical or vertical faults was allowed, which possibly gives a more realistic simulation of the real processes of subsidence in such a large body of rock. Laboratory studies of the reservoir joints included roughness measurement, JRC and JCS characterization, direct shear tests while saturated in heated Ekofisk oil, and coupled closure-shear-flow tests with heated oil followed by heated sea water. Discontinuum modelling using Cundall's UDEC was performed on representative jointed assemblies (two sets of steeply dipping conjugate joints) to investigate the effect of a major reduction of pore pressure within the deformable matrix and along each joint. It was found that the large shrinkage deformation of the matrix allowed joint shearing to occur despite the constraint of uniaxial strain. Relative mass bulking due to small but widely distributed joint shear possibly explains the observed maintenance of excellent productivity despite large vertical strains in the reservoir.

Jan 1, 1986

By P. J. Bartlett

Premier Diamond Mine exploits a kimberlite orebody using cave mining methods. A drilling level is established at the base of a block of ore to effect undercutting that leads to caving of the overlying ore. A second level is developed some 15 metres below the undercutting level to allow extraction of the ore once it has caved. As much as 45 per cent of the rock is removed on the extraction level creating a series of pillars. Undercutting creates abutment stresses, as high as 3 times the virgin stress, which affect the rock mass to a distance of 20 metres from the undercut face on the undercut level and on the extraction level 15 metres below. If the extraction level is completely developed prior to undercutting, where stress levels exceed 20 percent of the rock mass strength, extensive rock mass and support damage occurs as the undercut passes overhead. Rock mass damage takes the form of movement along existing joints and minor shear failure through intact rock. Support damage takes the form of cracking in rigid concrete linings. Where induced stresses exceed 50 per cent of the rock mass strength it is often impractical to keep excavations on the extraction level open. Rock mass damage takes the form of extensive failure of the rock in shear which evidences itself as propagation of the fracture zone around tunnels and footwall heave. Support damage results in destruction of shotcrete linings and concrete footwalls. As the interbolt support fails, badly fractured rock ravels around the steel tendons. Observation and monitoring at Premier Mine and on other cave mines has shown that induced stress levels and consequent damage are a function of :?the extraction ratio on the undercut and extraction level prior to undercutting ?the shape of the undercut face ?the rate of undercut advance ?the distance of leads and lags between adjacent tunnels on the undercut level. To ensure the stability of excavations, all of the above parameters must be carefully planned and the planned mining sequence rigidly enforced. The minimum of development is completed on the extraction level prior to the undercut passing overhead. Required development is then rapidly completed once the area has been de-stressed. Support is installed in three phases: ?Rockbolts are installed as soon as excavations are developed ?Wire mesh, steel tendon straps and a layer of shotcrete sufficient to protect the mesh and straps from damage by blasting and LHD loading is installed as soon as practical thereafter. Inevitably the shotcrete lining has to be replaced once the undercut has passed overhead.. ?Rigid shotcrete linings and concreted footwalls are completed only after the undercut has passed overhead and the area has been de-stressed.

Jan 1, 2000

By Bimal Nathwani

This paper presents an overview of bearings failures with focus on steel mill applications such as continuous casting, rolling mills, multi-roll cluster mills and wire and rod mills. This paper will also provide countermeasures for prevention of these modes of failures.

Jul 30, 2018

By E. L. Litchfield

This report of work by the Federal Bureau of Mines has two primary objectives: A survey of the present status and usefulness of the minimum ignition-energy concept, and the presentation of recent data that are believed to bear on the safety problem associated with the ignition of combustible gases by electric discharges. The minimum ignition-energy concept has widespread applicability, especially to safety. The primary obstacle in making theoretical calculations of the requisite ignition energy is the lack of data on chemical kinetics and flame hydrodynamics. The new data on electrical ignition are representative of the great increase in knowledge that can be achieved by proper utilization of geometrical and electrical characteristics associated with the ignition source. CONCEPT OF MINIMUM IGNITION ENERGY The basic concept of a minimum ignition energy (the minimum amount of energy required to cause ignition) follows quite naturally from general physical principles and from the stability (lack of chemical reaction) of the gaseous mixture under the initial conditions. It also follows that if, as a first condition, lossless, instantaneous, and spatially localized energy can be injected and, as a second condition, the relaxation time for conversion of this type of energy to the type required for the reaction is short compared to some characteristic time scale of the ignition phenomenon, the energy requirements will be essentially independent of the type of energy source. Even if condition one cannot be fulfilled, it is sometimes possible to estimate the energy content of the gas required for ignition, and under these circumstances, condition one is fulfilled in effect. There are several instances where results can be interpreted for circumstances that effectively satisfy conditions one and two; these will be discussed later.

Jan 1, 1960

By McGuirk. C. H.

The Port of Conneaut, long regarded as a leader in advanced bulk material handling technology, recently incorporated into its existing facility a new, multi-million dollar coal transfer-storage system. While the basic principles of conveyorized bulk material handling remain unchanged in the new system, design modifications such as rotary dumping of railroad cars, automated car feed to dumper, belt rip detection for conveyor belting, bucket wheel continuous production, and other innovations make The Pittsburgh and Conneaut Dock Company's complex worthy of classification as the "Port of Tomorrow - Today". The Pittsburgh & Conneaut Dock Company, the "Port of Tomorrow - Today", 1s a bulk materials storage and transfer facility located on Lake Erie, 68 miles east of Cleveland, 30 miles west of Erie, PA., and 138 miles north of Pittsburgh. Figure 1 shows an aerial view of the facility. It is designed to handle over 25 million tons per year of metallurgical and steam coals, direct shipping ore, fine ores, concentrates, pellets, limestone, and dolomite. Inbound shipments of iron ore and limestone are received from Minnesota, Michigan, Labrador, and Quebec. Coal arrives from Pennsylvania, Ohio, Virginia, West Virginia, and Maryland. Rail service is provided by the Bessemer & Lake Erie Railroad Company.

Jan 1, 1980

By T. C. Wesson

The need for elemental-analysis information on coal mine dust for use in health and safety research prompted this study by the Bureau of Mines. Neutron-activation and X-ray fluorescent techniques were used to obtain five-element analysis (silicon, aluminum, iron, calcium, and magnesium) on 444 samples from 68 coal mines in 10 States. From these analyses, the average composition of the dust in coal mines was determined. The contribution of the primary dusting material (limestone dust) to the makeup of coal mines was shown. Regional differences in mine-dust composition were indicated.

Jan 1, 1974

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"In recent years, much has been said and written on Lake Superior ores, giving the impression that the quality of the ore is deteriorating in grade and that the reserve of high grade ore is rapidly being depleted. Average analyses of ore produced in this district since 1902 show that the average quality has been practically uniform since 1910, and now closely approximates the average for the total reserves of merchantable ore.The accompanying tables and charts show the average analyses for the past ten years, weighted according to tonnage: The chart above shows graphically the average natural iron content for the old range, Mesabi, and grand total Lake Superior ore shipments since 1902.During the last ten years the decrease in iron content for shipments from all ranges except the Menominee was only' .05 of 1 per cent, while for the Menominee ores there was an increase of .052 of 1 per cent. These tabulations and the chart prove that the average quality of the total annual production of iron ore from the Lake Superior district is uniform. Mining men of the district know that all of the merchantable ores of every ore body are being mined out cleanly, and therefore the present average iron ore content of total annual shipments from the district may be expected to continue as long as the present merchantable ore reserves last. There is no logical reason to expect a decrease in the average iron content. Furnaces require ore of definite quality, and if this quality of ore cannot be produced from the natural ore bodies, it must be produced by mechanical means—that is, by concentration of low grade ores or iron formation."

Jan 1, 1920

By Henry Fay

LAWRENCE ADDICKS, New York, N. Y., (communication to the Secretary *).-There are two points regarding gun erosion on which I want to say a few words: The first is about the analogy to hardening of wire by drawing and the second the possible role played by thermal conductivity of the metal. The ductile metals do not necessarily become brittle when cold-worked as it is possible to draw copper from 3. in. in diameter soft rod down to the finest hair wire without annealing. This results, as stated in the paper, informing a hardened core with a very hard skin. The electrical conductivity is depressed some 3 per cent. and the tensile strength nearly tripled. A soft copper wire 0.08 in. in diameter and 6 in. long may be twisted 150 or more turns before the wire will snap under torsion. A hard-drawn wire will break after perhaps a dozen twists, the skin breaking down at one spot. Just wiping the wire with a cloth clamp with dilute nitric acid has a remarkable effect in increasing the number of twists without appreciably lowering the tensile strength, showing the skin to be very thin. On the other hand, pickling the rod, from which the wire is to be drawn, in dilute nitric acid also greatly increases the number of twists which can be applied to the resulting wire. This indicates that the copper oxide scale produced when the wire bar is rolled hot is more or less rolled into the rod and may have much to do with the skin effect. We also know that if the conditions of drawing are not correct, the heat of deformation in the die may produce quite an annealing effect. The application of this analogy to what occurs in a gun to produce the effects noted offers some difficulty. The second point is that as the temperature of the surface of the gun bore has undoubtedly a great deal to do with the amount of erosion, one natural remedy would be to conduct the heat away fast enough to keep this temperature within desired limits. This brings up the question of the thermal conductivity of the metal of which the gun is made. We know that the conductivity of pure metals is greatly altered by alloying and that the alloy is usually, though not always, lower in conductivity than the metal before alloying. This is interesting when it is considered that the high-nickel and manganese-steel alloys show greater erosion as stated. Would it not be instructive to study the question from the point of view of heat conducted away from the eroded surface?

Jan 3, 1917

By Burns K. L

Keyboard patterns of hundreds of minor faults with vertical displacements of 3 mm to 2 m occur within the Greta coal seam and cause serious mining problems in collieries. Many of the faults are concentrated in linear zones termed swarms. One swarm is 600 m wide and more than 800 m long and others are of comparable size.The minor faults between the swarms are normal and are relatively widely spaced and show dip-slip movements, but the faults within a swarm are clustered and show strike-slip and oblique-slip movements. Fault swarms ofthis size and frequency have not previously been described from the Sydney Basin or on a comparable scale elsewhere but appear to be a widespread phenomenon in Australian coalfields. The faults are assigned to classes onthe basis of orientation which are then assigned to sequential phases I to IV on the basis of offsetting relations between representatives of each class. Phase I faults are minor thrusts. Phase IT, Ill, and IV faults are concentratedin the swarms and show sinistral strike-slip and normal dip-slip movements. The interference of slickenlines indicates that multiple movements have occurred within a single phase; their order is (i) strike slip (ii) dip slip and (iii) oblique slip. All faults truncate and post-date both cleat and sedimentary "stone" dykes.Phase I minor thrusts trend at a high angle to the Hunter Thrust and are considered to predate the Late Permian movements on the Hunter Thrust. Phase II and III minor faults are younger and may be any age between the latePermian and Tertiary.

Jan 1, 1978

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By Pengfei Wang, Guorui Feng

With increase of cover depth, dynamic incidents, such as large gateroad convergences and coal bursts, are frequently encountered when mining deep longwall panels. It would be more adverse due to large inclination of the coal bed. Because of the shearer and armored face conveyor (AFC) sliding downhill, toppling of shields, disconnection of AFC to the stage loader are related to it. Tangshan coal mine is a typical deep, inclined coal mine situated in the east of China. The split-level longwall panel layout is being adopted for mitigating problems above, where tailgate entries of longwall panels are driven below gob edge and along the floor, while headgate entries are driven along the roof. Wire mesh and steel sets have been used empirically for support for tailgates for about a decade, which reduces the tunneling speed. In view of this fact, the paper serves to investigate the proper adjustment of the tailgate locations and to analyze the resulting stress and yield conditions according to support strategy. First, field measurements and observations were carried out. Stress data distributed within surrounding rock mass were obtained, especially within the roof since the roof consists of only a coal sheet with a thickness of 2–4 m. Roof pressure of the tailgate represents the pressure at the gob edge since it is below the gob edge. The convergence data were also collected. Numerical modelling using FLAC3D™ was conducted and validated by side abutment stress data. The double-yield constitutive model was used to simulate the gob. The finalized tailgate layout and design were determined through comparison of three scenarios. The research in this paper can help engineers choose the proper tailgate layout and support strategies for coal mines that are going to adopt a split-level longwall panel layout for mining deep, inclined longwall panels.

Jan 1, 2018

By Víctor Cobeña

El presente trabajo señala el desarrollo de la simulación de disparos por computadora -en tanto está diseñado para solucionar problemas de voladuras en las minas, canteras y obras civiles. El programa elimina el costo invertido en los métodos convencionales de "ensayo y error" de pruebas de campo y optimiza las operaciones de voladuras.

Jan 1, 1987

By Alexandra Garcia

A measurement-based ground control management system, commonly employed in coal mines, has been successfully implemented in a UK potash mine operating at a depth of over 800 m. This system includes the routine deployment of telltales in roadways throughout the mine to mitigate against the risk of large-scale roof falls and the deployment of detailed ?design monitoring? instrumentation for ongoing design verification. The routine monitoring systems used in coal mines have not been, to date, commonly applied in potash mines, despite the similar, variable weak geology and associated ground control hazards. Monitoring information from the site indicates that telltales can be deployed to monitor roof conditions, with action levels based on differential rates of strain, as opposed to absolute movement.

Jan 1, 2014

By D Bruce, D Cox

The main access decline at Carrapateena mine was excavated through two different underground aquifers. In these areas of decline, pressurised water finds the path of least resistance through the rock and into the excavation. In some locations the ground water would upwell underneath the roadway resulting in rapid deterioration of the running surface. The deterioration of the road was so rapid that the two areas of decline required significant roadworks every single shift or it would become impassable by mine traffic. With a full fleet of underground trucks hauling to the surface, managing these sections of roadway was impractical and unproductive. The site team resolved this issue by installing Roller Compacted Concrete (RCC) to the affected sections of decline. RCC is a specialist concrete product that is delivered to the site near dry and is installed using a grader and roller similar to road base. This product can be installed quickly and be trafficked within hours of installation, making it ideal for mines with single access declines and unfavourable road conditions. RCC roadways were successfully installed at Carrapateena mine in conjunction with under-road drainage. These roadways have proved to be a very effective solution which requires minimal maintenance and are resistant to water ingress from the aquifer. This paper discusses the technical aspects of the RCC, as well as the practical implementation of the solution as a whole.

Mar 15, 2021