Search Documents

By C. A. Stetefeldt

In a former paper (Runs., xxi., 286) I described the plant of the Marsac Refinery, and the manipulations of the process, but cou1d not, at the time, give reliable statistical results. To supply the latter is the object of the present paper. I shall give actual facts as correctly as possible, without any bias one way or the other. For all statistics I am indebted to Mr. W. G. Lamb, who has charge of the Marsac lixiviation-plant and refinery; to Mr. A. Luebeck, assayer at the Ontario mill; and to the Daly Office, Salt Lake City.* Before starting on the work of the year 1892, a most careful clean-up was made, and any remnants were charged to the refinery. During 1892 the Marsac lixiviation-works produced 48.8 tons of so-called "regular" sulphides, which contained, on an average, 11,449 ounces of silver per ton; 11.77 ounces of gold per ton; and 569.8 pounds of copper per ton. To this must be added, 266 pounds of sulphides and by-products left over from the product of 1891, which contained 1380 ounces of silver, 1.41 ounces of gold, and 63 pounds of copper. Before giving the results of the clean-up, a general discussion of the items of expense, methods of assaying, etc., is desirable.

Jan 1, 1895

By C. D. Hall, F. E. Dollarhide

Fluid Ioss agent.s for crude oil and for water have been studied in dynamic tests. A treatment using a spearhead with a fluid loss agent followed by plain fluid appears feas ible in crude oil, but not in water. An equation for spearhead depletion shows that spurt loss relative to fracture width must be low, if the portion of spearhead fluid in the treatment is to be small. The presence of colloidal matter in crude oils aids the fluid Ioss agent. Unlike in kerosene, where flow limited the agent deposition, in crude oils the filter cake continually formed and leak-off declined. The volume-time relation varied somewhat for different crudes, but was best described by a square root of time function. Spurt loss was inversely proportional to agent concentration. After the fluid loss agent initiated the filter cake, the crude oil colloids built on it effectively. A 2-minute or a 5-minute spearhead with double the normal agent concentration gave the same fluid Ioss curve as the same concentration did for a 30-minute test. The agents tested in water gave fluid Ioss plots on which, for the first few minutes, volume was proportional to the square root of time, but later became proportional to time. For fracture area calculation the customary square root of time function is a satisfactory approximation. Leak-off rates and spurt losses were higher in water systems than in oils. The spurt Ioss tended to be inversely proportional to concentration. In spearhead tests, the filter cakes were not eroded by water flow. However, the rather high spurt loss values make spearhead treatments impractical for water-based fluids. Introduction The effects of dynamic testing conditions on the performance of fluid loss agents in kerosene have been studied previously.' We have extended the work to include crude-oil- and water-based fracturing fluids. An understanding has been gained of the mechanisms of formation and functioning of the filter cakes of fluid loss agents. The practical aspects of evaluating performance of agents in relation to fracture area calculations also are considered. The feasibility of using the fluid loss agent in a spearhead stage of the treatment is examined further for both types of fluids. Experimental Procedure The dynamic fluid loss tests were performed in an apparatus similar to the high-pressure apparatus described in a previous publication.' A fracturing fluid was circulated over a rock surface located in a closed pressurized loop. The fluid flowed axially over the cylindrical surface of a core 2 in. in diameter X 3.5 in. long, mounted (with the flat ends sealed off) in a pipe, with 0.117 in. annular clearance. The filtrate was collected in a central hole in the core and led through valves to graduated cylinders. Provision was made for changing quickly the circulating fluid during the test (spearhead runs) without interrupting the filtration pressure. The only modifications were to add heating tapes and water jackets for the tests with crude oils, all conducted at ISOF, and to change all parts exposed to the test fluid to stainless steel for the tests with water-based fluids. The latter tests were made at room temperature, 80F. Three crude oils were tested. A mixed crude, obtained from a local refinery, contained a considerable amount of light ends. For safety reasons, it was stripped to 250F vapor temperature before use in the fluid loss tests. The other two oils were used as obtained from lease tanks. One was a greenish-brown, 37" API paraffinic crude, and the other was a black, 32" API asphaltic crude. The fluid loss agent for oil, here designated for brevity as Agent A, was Adomite@ Mark II*, a granular solid commercial agent, the same as previously tested in kerosene.' Three different compositions of fluid loss agents were tested in Tulsa tap water. Agent B was adomit& Aqua*, a solid commercial fluid loss agent, comprising clays and hydrophilic gums principally derived from starch. Agent C was a mixture of three parts of Agent B with two parts of silica flour. Agent D was Dowel1 J137, a mixture of guar gum and silica flour. The test cores were cut from contiguous blocks of Berea or Bandera sandstones. For the oil tests, the cores were oven dried, evacuated, saturated with kerosene, and the kerosene permeability was measured. The cores used with the water-based fluids were pretreated by saturating with 3 percent calcium &loride solution to minimize pemeability damage by the fresh water due to clay migration. The

Jan 1, 1969

By T. S. Fuller

The tensile properties of steels at elevated temperatures have been studied by numerous investigatorsll primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20" to 500' C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures2 for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon if increased tensile strength and decreased ductility .in the so-called "blue-heat" range, approximately 200" to 300" C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

By Mohamed Mortada

A practical analytical method is developed in this paper which provides the practicing reservoir engineer with a handy method for analyzing oilfield interference problems. The procedure employed entails the principle of superposition of individual eflects. A set of charts has been developed and can be used to evaluate the individual effects. The charts represent non-steady state pressure distribution in an extensive aquifer due to a constant rate of production from an oilfield which can be approximated by circular geometry; they are constructed from solutions to the diffusivity equation considering a circular sink as distinguished from a point sink. The solutions are obtained partially from mathenlatical considerations and partially from analog and digital computations. By virtue of the method of images, the charts can be used also to treat the case of production near a fault. In addition, provisions are made for treating oil fields, which are produced by partial water-drive. Treating an actual field case is deferred to a subyequent writing; however, illustrative example is presented to demonstrate the method of application. The pressure distribution in linear and limited radial aquifers is currently under study. INTRODUCTION With the increasing difficulty of discovering new oil reserves, attention is necessarily focused on the efficient development and production of existing reservoirs. Efficient production depends on the availability of reliable means for predicting the pressure-production behavior of oil fields. The prediction is usually performed by analytical methods or computers. Analytical methods are often limited to systems which can be approximated by simple geometry. However, analytical methods have the distinct advantage of being readily performed without special equipment. Analog and digital computers lend themselves to a variety of problems, but are not always locally available and consequently their use is limited. One particular situation in which analytical techniques are needed involves studies of multiple, water-drive oil fields sharing a common aquifer. Such oil fields are in hydrodynamic communication. Therefore, production from any of the oil fields is accompanied by a pressure decline which is transmitted through the aquifer to the other oil fields and manifested as pressure interference. The rate of propagation of the pressure decline is such that the pressure may be significantly reduced many miles away from a producing pool. An example of pressure interference is found in the Woodbine formation in East Texas. There. a dozen or more pools, including several of major size, draw on the Woodbine formation for water drive. The pressure in the water-bearing portion of the formation has been significantly reduced over an area of several thousand square miles. This reduction of pressure has been such that when the Hawkins pool was discovered in 1940, the pressure in it had already been reduced 280 psi below the initial value in the aquifer. This resulted from prior production from other Woodbine sand pools, including, in particular, the East Texas field some 20 miles to the east of Hawkins.' The above example indicates that the interference effect can be significant and should be taken into con-

Jan 1, 1956

By Zou Zhongpping

Under the new normal state, blast furnace outputneeds to be adapted to the market demand, however the limitation in blast furnace output has significant impact on blast furnace operation and is prone to cause inactive furnace hearth and higher fuel ratio. To address such problems, some practices to maintain stable and smooth operation of blast furnace in case of output limitation are proposed based on data analysis philosophy, which allows the blast flow and hence the top pressure to be determined based on the hot metal output, and adequate kinetic energy of blast supply can be assured by adjusting the tuyeres. Matching between the oxygen enrichment and the pulverized coal injection is also proposed based on theoretical flametemperature, and burden distribution cycle calculation method is proposed, whichoffersnew approach for analyzing the change in burden distribution pattern.

Oct 30, 2017

By P. Morissette

Passive monitoring of support performance during rockbursts was conducted at three deep underground mines. A comprehensive database was constructed of 172 seismic events and the associated damage to support systems at 266 mine locations from January 2000 to September 2012. The majority of pertinent information was obtained through seismic system records and on-site field assessments. This work assesses the quality of collected information and evaluates the dynamic-load demand on support systems in seismically active mines.

Aug 1, 2013

By J. M. Elegante

A belt drive attendant was working underground during his shift at the junction of two belt drives. He worked alone, but communicated with others at the mine by underground phone. At noon his shift foreman stopped by his workstation. At 2:00 p.m. he was contacted by phone by a fellow belt drive attendant. At 5:00 p.m., he was found dead by the oncoming evening shifter.

Jan 1, 1989

By Viswanadham B. V. S., Babu K. V

Wind energy is one of the most economical renewable energy sources. In order to support wind turbines onshore or offshore open-ended monopile foundations are widely used. Unlike conventional structures, wind turbine foundations experience a large magnitude of lateral loads in the order of 20 % to 30% of total vertical loads. The presence of soft clayey layers at shallow depth along the coastal region, offers lesser lateral load resistance to monopile foundations. One option to enhance lateral load capacity is by introducing fins to the outer surface of the monopiles. Studies pertaining to lateral load response of finned piles in clayey soils are very sparse. This paper presents some of the numerical model studies on the lateral load response of monopiles and finned piles in soft and stiff clay. In the present study, three-dimensional finite element analyses were performed on monopiles as well as finned piles. Analyses were performed in clay with different consistency varying from soft to stiff. Pile material is mild steel for all analyses. The pile section modeled as linear elastic material whereas soil was modeled as Mohr – Coulomb constitutive model with non-associated flow rule. Monopiles and finned piles having four and eight fins with different fin sizes and configurations are considered during the analyses. Finned piles advantage over monopiles to resist lateral load is highlighted in the present study. The results have shown that fins are effective to enhance the lateral load carrying capacity of monopiles and also it reduces the bending moment in monopiles for a given design load.

Sep 1, 2022

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996

By S. J. Neethling

"Flotation is a complex process with many factors that influence the performance of a cell. This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another.In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates. This interaction between variables makes it very hard to experimentally separate the impact of, for instance, the air rate from that of bubble size or bursting rate. In the simulator, though, it easy to make independent changes to these variables.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system’s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries."

Jan 1, 2003

By Wilfredo Serrano

El presente artículo describe la historia, características, especificaciones, ventajas de la máquina WS Morococha de gran volumen. Dicha máquina fue diseñada en 1966 en el asiento minero de Morococha y es utilizada para concentrar minerales por el método de flotación de forma económica. Entre las principales ventajas tenemos: gran volumen y capacidad por unidad, bajo costo de inversión y mantenimiento, la operación es independiente en cada máquina, su alto radio de concentración permite obtener rougher concentrados limpios directos y que en las paradas no se pierden el volumen del mineral retenido y el punto se descarga en la parte superior. De forma que esta máquina concentradora de minerales por flotación de concepción y desafíos mejorados, desarrolla mayor eficiencia y selectividad.

Mar 1, 1976

By A. J. Hyett, N. Hedrick, J. Blackall

The Garford bulb anchor is a modified cable geometry developed and patented by Garford Ply Ltd. of Australia, and which has recently become widely available in Canada. It is produced by deforming the seven wires (including the central kingwire) of a standard cable into a bulb" (Fig. 1). Laboratory cable pull tests indicate that the bond capacity of the 25 mm Garford bulb anchor is comparable to the nutcase cable, in excess of the birdcage cable, and significantly higher than standard 7-wire strand. Its comparative advantage over the latter is most significant for tests at low radial confinement and high water:cement ratio grout, which corresponds to operational conditions of low quality rock (i.e. weak, highly fractured rock masses, foliated hanging walls, failed ground, etc.) and poor installation quality control (perhaps the most common explanation for cable bolt failures). It is under such conditions that cable bolting is often ineffective. The most impressive result is that for a reduction of the effective rock mass modulus by a factor of five, the Garford bulb cable capacity remains virtually unchanged.

Jan 1, 1995

By Alim Ullah

Process, quality and management control are necessary in order to produce DRI of required quality and at minimum cost. Although the characteristics of the two (2) principal inputs, that is, iron oxide feed and natural gas (for gas-based DRI plants) can affect the operation of a DRI plant significantly, they are outside the control of plant operators, at least in the short run. The quantity of reduction gas, its composition and reduction gas temperature are some of the key process variables. Statistical Process Control (SPC) can be used in a DRI plant to minimize the production of off-grade material and costs, as well as to improve the overall operation of the plant. One of the key quality variables to be measured and controlled is percent metallization, defined as FeM/FeT*100 where, FeM and FeT respectively are metallic iron and total iron in DRI. Control charts are used to monitor the quality of DRI produced and, when necessary, corrective actions are taken to bring the product back within the control limits. Management control can consist of essentially following how well the plant performs against some pre-established standards of parameters like daily production, downtime, consumption of material and energy, etc. In this respect, it is suggested that yield, defined as theoretical consumption/actual consumption of iron oxide feed, be used to monitor the consumption of feed material. Similarly, instead of using natural gas per ton of DRI produced, a better criterion would be efficiency, defined as theoretical natural gas consumption/actual natural gas consumption.

Jan 1, 2006

By Kavanagh M. E, Henley R. W

The Meekatharra mining district lies in the northern pan of the Murchison Province of the Archaean Ynlgam block of Western Australia. Since dis- covery of the Paddy's Flat belt in the district in 1897 total gold production has been 67 tonnes and a further 33 tonnes in resources have been defined by drilling. The Paddy's Flat gold deposits occur within the Gabanintha Formation, a basal formation of the Murchison greenstone sequence containing komatiitic basalts, ultramafics and minor banded iron formations. The regional control on the distribution of deposits is an anastomosing shear belt which extends over 350 km and incorporates the Mt Magnet, Reedys and Meekatharra deposits. The following gold deposit styles may be recognized based on lithological association and alteration: Albite porphyry hosted, Carbonate-fuchsite- quartz alteration hosted deposits, Banded Iron Formation hosted sulphide replacement gold deposits and quartz vein deposits. With the exception of the banded iron formation hosted deposits, the Paddy's Flat alteration zone shows strong similarities to the alteration styles at Kerr-Addison (Ontario).

Jan 1, 1991

By A. Gibson

Most methods for the treatment of scrap printed circuit boards do not reclaim the components in working order as the boards are either fed to a copper smelter, to recover the valuable elements, or, simply landfilled. This work reports the dissolution of the solder in fluoroboric acid containing Ti4+ ions which was particularly selective for solder, allowing the components to be recovered. The solder was subsequently electrowon from the leachant. The boards were then shredded and the copper dissolved in ammonium sulfate and, then treated via solvent extraction to give an electrolyte suitable for electrowinning. The remainder of the metals were dissolved aqua regia, silver remained unattacked by the aqua regia, palladium precipitated as Pd(NH4)Cl6 in the presence of zinc and nickel, the gold was removed by solvent extraction and precipitated as nanoparticles. The aqua regia was then diluted and the zinc and nickel separated by solvent extraction.

Jan 1, 2009

By Jian Li, P. Liu, R. Zhang and J. Lo

In the past decades, focused ion beam (FIB) has evolved into a powerful microscope that provides capabilities that no other microscopes can offer. The combination of high-resolution imaging and stress-free ion beam cross sectioning provides valuable microstructure information both at the specimen surface and beneath. FIB techniques are also the preferred method to prepare site-specific transmission electron microscope (TEM) specimens. CanmetMATERIALS owns a world-class microscopy facility, where advanced microscopy work provides strong supports to research programs that cover a wide range of subject areas. This paper is aimed to provide a few practical examples of FIB applications in microstructure characterizations that include cross-sectioning and imaging, serial sectioning, and advanced TEM specimen preparation in materials research at CanmetMATERIALS.

Jan 1, 2015

By C. H. Bucknam

Acid neutralization titrations were applied to the characterization of soil and overburden for the control and prediction of acid rock drainage in the coal fields of the eastern United States in the 1970?s (1). These became known as the Sobek methods as a result of the early United States Environmental Protection Agency publication and the methods have been modified (2) to be adapted to many applications in the metal mining sector (3,4,5,6,), and, as a result, there are a large number of acid neutralization potential methods being used that are referred to as Modified Sobek methods. Standardization of neutralization potential methods for metal bearing ores and related materials based on carbonate carbon, rather than titration, commenced in the 1990?s through the American Society of Methods and Materials (ASTM) Committee E01 on Analytical Chemistry for Metal Ores and Related Materials Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials (7). A subcommittee section, E01.02.05 on Environmental Methods, was organized to coordinate the method and material standardization efforts of ASTM and the Acid Drainage Technology Initiative Metal Mining Sector (ADTI-MMS) Prediction Committee (8), which took on the project of standardization of the acid neutralization potential acidity titration method (ANPA) to supplement the carbonate carbon method in E1915 (9) for application to samples which have metal carbonates (10), in particular, which result in overestimation of the neutralization potential using the carbonate carbon methods (11).

Jan 1, 2010

By P. G. Gresse

The Orange-Vaal River system is known to be the primary secondary source for alluvial diamond deposits in the northern Cape and along the west coast of Namaqualand. The higher order sources for diamonds contained within this system are still not defined entirely to satisfaction, but certainly include kimberlite pipes exposed in the catchment regions of these rivers. The focus of alluvial diamond mining along the Orange-Vaal system recently changed from the traditional areas in the upper catchment regions?the Barkly West, Christiana, Bloemhof, Wolmaranstad, Schweizer-Reineke region, and the lower regions near the mouth of the Orange River at Baken, Alexander Bay and Oranjemund, to the area between Douglas and Prieska?the so-called mid-Orange region (Figure 1).

Jan 1, 2003

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The usual run time errors occur when illegal mathematical operations are attempted by MFIRE For exam¬ple, if the user enters a negative value for the input variable HEAT to model a heat sink or cooling station, a run tame error will occur because an exponential function is employed to better model the changing temperature dis¬tribution in the airways. DATA FILE ERRORS Two types of data file errors can occur. 1 An error may occur because the input data file itself is invalid This may be caused by: The data file cannot be found due to incorrect spelling, drive, or path specification Check the spelling and path at the prompt for location of the data file. The data file contains non-ASCII symbols Check op¬eration of the text processor to insure that only ASCII characters are produced Delete all non-ASCII and/or all out of place characters. 2 Data are accepted by the program, but are incorrect for the data types or ranges or the combination causes a data inconsistency This may be due to. An invalid character is located where a numerical value is required The input data value is outside the reasonable range The input data is insufficient to build the model for simulation. The input data exceeds the capacity of the program. PROGRAM ERROR DETECTION When the program is running, tracing messages are given on the screen indicating the group and lines of data that have been read and the section of the program that is executing Program termination indicates that problems are caused by the subsequent (not read) data file section. For each detected error, descriptive message starting with * ERROR * is issued and the program terminates. When a possibly wrong value and/or its calculated intermediate result is detected, a descriptive message starting with * WARNING * is issued and the program continues. If a modification of input value or calculated intermediate result is automatically made by the program, descrip¬tive message starting with * ATTENTION * is issued and the program continues. LOCATING ERRORS If a message indicates that the error condition occurred due to the data input file, locate and correct the data item. If no error message is issued, but the simulation results are not as expected, carefully check the list of input data shown in the output file WARNING messages and ATTENTION messages may reveal an error in the input data even though the program continues to operate Insure that the default values or modifications adopted by the program run are acceptable. Anomalistic data, though not incorrect or impossible, may lead to an unusual simulation For example, making a fan unusually powerful may prevent a normal strength fire from affecting the airflow distribution in the system Much care must be employed before considering an ex¬treme case. If a message indicates that the accuracy criterion in the temperature section of the program was not satisfied, a table detailing the current parameters of airways which have large fluctuation in the average air temperature from iteration to iteration is produced If the pattern of the parameters is clearly cyclical, while the variation of natural ventilation pressure is stable or cyclical from iteration to iteration, then, most likely there is no single equilibrium stage for the event If the variation of natural ventilation pressure decreases steadily though slowly, increasing the value of data item variables MADJ or ITN (on control line number 1) may allow convergence.

Jan 1, 1990

By John Arrell, James Stuart

We have developed a tester that is uniquely able to measure the no-fire power level of certain types of electro explosive devices (EEDs). In the past, it has been difficult to establish a no-fire power level for nonlinear conductors, such as semiconductor-bridge (SCB) EEDs, and conductive-mix EEDs.

Jan 1, 2011