Search Documents

By R. Maurice King

In the operation of today's large scale ore-processing mills, it is extremely important to have some way of making an objective evalu¬ation of the performance of the available flotation reagents. Attempts to do this may often result in inconclusive findings since the magnitude of the difference in the mill results for any two reagents is apt to be quite small compared to the variability introduced by the process and 'the analytical procedures used to measure them. In cases where two reagents give vastly; different mill results, evaluation becomes a simple matter and as such deserves no further attention here. A question of primary concern, however, is how a mill can go about evaluating the performance of two reagents which may, for example, give a difference of only 0.001% copper in the-tailings or of 0.2% in copper recovery. The casual observer may feel that such small differences may be of little importance, but in a mill-whose daily tonnage is between 30 and 40 thousand, these differences could mean a substantial savings. Before the presentation of an actual example of a reagent testing scheme designed for just this-purpose, perhaps a few minutes should be devoted to a review of some statistical methodology to be used later in the discussion.

Jan 1, 1964

By E. R. Torak

Custom Coals, International has installed and is presently testing a 225 kg/hr. (500 lb/hr.) micronized-magnetite, fine-coal cleaning circuit at PETC's Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program's High Efficiency Preparation Subprogram. The project includes design, construction and testing of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense-medium cycloning of the 300 by 30 micron feed coal using three different size micronized-magnetite mediums, and medium recovery circuits using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

Jan 1, 1996

By Abhiram Kumar Verma, Soumya Ranjan Mallick

Generally, waste such as soil and sandstone is used in mines for road construction or haul roads. In many such mines, it is challenging to design haul road pavement to match the dumper capacity. This paper investigates overburden soil to find its utility as a pavement material. It is found that overburden soil is unsuitable pavement material without stabilization; hence, nine composite materials are developed using overburden soil and RBI. Physical, mechanical and microstructural properties of unstabilized and stabilized soil are determined. Statistical analysis is carried out to assess the effect of soil type, RBI and curing period of strength characteristics of unstabilized and stabilized soil. ANOVA tests assess the influence of RBI percentage on soil geotechnical properties, and regression relations are developed. Two-way ANOVA shows the effect of RBI and soil type on soil geotechnical properties, whereas one-way ANOVA shows that the influence of soil type is more than the RBI. The regression relation is developed for CBR, UCS, Poisson’s ratio and modulus of elasticity with a good correlation coefficient. The performance of RBI is more with the finer material and reduces with an increase in the size of soil grains. The performance of the developed composite is better than the earlier developed composite based on overburden with fly ash, lime kiln dust, lime or clinker.

Mar 19, 2024

By John Birkinbine

EXTENDED discussions, by inviting attention to problems affecting the conservation of natural resources, have encouraged investigations as to their sufficiency, with the general result that the more thorough the examination, the less cause appears for anxiety as to the exhaustion or serious depletion of these resources. The extent of industrial development, the large plants and the enormous volumes of materials required, when compared with conditions a few decades ago, are sufficiently startling to enlist the attention of those who "fear .the pace," and yet in but few instances has real solicitude for the future. been warranted by a knowledge of true conditions. In a former communication, presented 5 years ago,1 I endeavored to emphasize the fact that true conservation represented the best utilization of reserves and not the locking up of resources for future use; a conviction which has become more pronounced as the subject was investigated. Prophecies of the, early exhaustion of mineral resources have raised the question as to our permanent reliance upon these, and encouraged inquiries which have in most cases developed reassuring conditions. But the fact that the future appears less dark than prognosticated cannot excuse wastefulness or improvidence; and detailed study which demonstrates an apparent abundance of natural resources should encourage their best application. In making inventories of resources one is liable to confine conclusions as to availability upon present circumstances and conditions in the past, or to formulate data for the future upon methods which are rapidly being displaced. In reserves which are not reproductive, such as minerals, the possibilities of exhausting the supply are startling if estimates assume that future extensions will follow methods which were less economical than those now employed, or to he used, and we dare not claim that the limit of advanced practice has been attained.

Jan 9, 1914

By Philomene Verlaan

This study examines the possible relationships between compositional variability in non-hydrothermal manganese nodules and large-scale environmental parameters. In the central SW Pacific (145-180° W and 20-O° S) the level of primary productivity, the rates and proportions of carbonate, silica and organic matter supply to the sediments, and the position of the seafloor relative to the Calcium Carbonate Compensation Depth (CCD) appear to directly influence nodule composition. Four zones of nodule composition are apparent. These zones correlate fairly well with the level of primary productivity in surface waters, as estimated by satellite-based measurement of chlorophyll content. The observed correlations between surface productivity and nodule composition are consistent with the contention that the dominant source of several transition metals in these deposits (i.e , Mn, Ni, Cu. and Zn) is provided by removal of fine-grained particulate matter from the water column by biological means. Subsequent decay of organic matter in sediments augments the content of these metals in the nodules through oxic and sub-oxic diagenesis. The opposite behavior of Fe and Co content may in part result from mineralogical and dilution effects.

Jan 1, 2000

By S D. Dessureault

In one of North AmericaÆs largest mines, which contains more than six active coal-producing faces, mine controllers must meet the complex challenge of adhering to the mine plan while also ensuring customer quality. Fleet management systems (FMS) provide many different avenues to control production flows, from the faces to the various pit crushers. Nonetheless, mine controllers must balance a variety of factors such as unplanned downs, differing customer demands, their own daily key performance indicators (KPIs) related to equipment utilisation, among others. Deviating from the short-term mine plan is the most common means of balancing the other factors, since adherence to the plan is traditionally only measured during the weekly variance meeting with engineering staff. However, such deviation may be one of the most costly responses, as long-term scheduling issues may arise such as multi-face dead-heading or insufficient stripping. This paper focuses on the development of a system for real-time adherence to mine plan within a control room environment. This system is part of a larger blending-focused, multi-million dollar project with elements of a centralised remote control room, developed at the University of ArizonaÆs Mining Information Systems and Operations Management (MISOM) Mine Control Center (MC2). The mine plan (MPL) component of the overall blending system integrates both historical and real-time FMS data with mine plan requirements directly sourced from original systems (no additional input required). The measures, displayed largely as graphs, have tools to help controllers manage the production to facilitate adherence to the plan. Some measures are designed to motivate crews to perform by inciting competition between crews, softened through a study of the controller culture. The MPL component was deployed at the mine, and the before and after deployment adherence was measured. This paper discusses the technical development of the new tool, its deployment, and an ethnography (study of culture) to understand controller motivation.

Sep 26, 2011

By John Starkey

"The development of the Minnovex SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.In the last century, it was deemed prudent to select up to 50-tonne samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5-tonne sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50-tonne sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By H. C. LIVINGSTON

At the Hanna No. 4-A mine of The Union Pacific Coal Co. a new system of trackless mining is being utilized to extract a 26-ft coal seam. By using shuttle cars and a conveyor belt for haulage in the rooms and panel entries instead of pit cars and panel hoist a saving of 12 cents per ton is expected. Mining is conducted in a 26-ft coal seam laid down on a synclinal structure with active workings on a pitch of approximately ten to twelve degrees. The coal seam is interbedded between a shale bottom and sand- stone top. The coal is friable, high in moisture, and subject to spontaneous combustion. The mine is rated gassy by the State Coal Mine Inspection Department. Mining is conducted at the present time by unbalanced rope haulage an main slopes spaced on approximate 4300-ft centers with the three-entry system driven to boundary lines, strike entries being turned on approximate 1300-ft centers. Panels are driven to the rise between entries at approximately 750-ft intervals with panel rooms driven on the strike 500 to 600 ft long, leaving 150 ft of barrier pillar between each block of panel rooms.

Jan 1, 1949

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

By Yun Bai, Sarah Wilson, Michael Salcher, Mark Trim

Over the last decade more than 62 miles (100 km) of civil transport tunnels were constructed in Sydney, Australia, using the sequential excavation method (SEM). The WestConnex motorway tunnels, each stage of which used over 20 roadheaders to excavate up to 40 tunnel headings, had numerous caverns up to 100 feet (30 m) wide and 82 feet (25 m) high. SEM tunnels in North America typically have far fewer active headings. This paper examines the differences in scope and risk allocation for construction phase services, including comparison of the Permit to Tunnel (PTT) process in Australia and the Required Excavation and Support process in North America.

Jun 23, 2024

By C. G. McLachlan

This paper outlines a series of tests carried out during the first six months of 1927, in the laboratory and mill of the Moctezuma Copper Co. The object of the tests was to determine whether the soluble salts present in the mill circuit water were having a detrimental cffect on the recovery made by flotation. To accomplish this object a series of water analyses were made, followed by flotation experiments in which definite quantities of the salts found were added as addition agents. Before proceeding to describe the results obtained in the course of the investigation, reference will be made to five articles that have appeared during the last two years in which the action of such salts is discussed. Two of these are by A. T. Tye1, 2 and describe flotation practice at Cananea and the way in which water high in ferrous and ferric salts is conditioned for differential flotation. Two, one by A. C. Munro and H. A. Pearse3 and the other by H. A. Pearse,4 outline Britannia milling methods, and the advantages that have been derived from ore washing; while in the fifth, A. W. Hahn5 summarizes the results of laboratory experiments in which ferrous, ferric and aluminum sulfates have been added in varying amounts. The mill of the Moctezuma Copper Co. has a daily capacity of 3000 tons, and is situated about 75 miles south of Douglas, Arizona, on the Rio de Nacozari, in the Mexican state of Sonora. The ore treated is mined from the company's mine at Pilares, about 5 miles southeast of the Concentrator. This ore contains about 2.5 per cent. copper— present almost entirely as chalcopyrite—and 10 per cent. iron, of which

Jan 1, 1928

By Maria S. Gudjonsdottir, Miao Yu, Gudrun Saevarsdottir, Pall Valdimarsson

Around half of the energy consumed in aluminum production is lost as waste heat. Approximately 30–45% of the total waste heat is carried away by the exhaust gas from the smelter and is the most easily accessible waste heat stream. Alcoa Fjarðaál in east Iceland produces 350 000 tons annually, emitting the 110 °C exhaust gas with 88.1 MW of heat, which contains 13.39 MW exergy. In this study, three scenarios, including organic Rankine cycle (ORC) system, heat supply system and combined heat and power (CHP) system, were proposed to recover waste heat from the exhaust gas. The electric power generation potential is estimated by ORC models. The maximum power output was found to be 2.57 MW for an evaporation temperature of 61.22 °C and R-123 as working fluid. 42.34 MW can be produced by the heat supply system with the same temperature drop of the exhaust gas in the ORC system. The heat requirement for local district heating can be fulfilled by the heat supply system, and there is a potential opportunity for agriculture, snow melting and other industrial applications. The CHP system is more comprehensive. 1.156 MW power and 23.55 MW heating capacity can be produced by CHP system. The highest energy efficiency is achieved by the heat supply system and the maximum power output can be obtained with the ORC system. The efficiency of energy utilization in aluminum production can be effectively improved by waste heat recovery as studied in this paper.

Mar 1, 2018

By C. Rutledge

The new mining method of multiple strata blasting, called StratablastTM, is described in a separate paper presented at this conference. The current paper presents three case studies where the technique was implemented in three different configurations in large-scale blasts in Australia. The first two blasts were in the Hunter Valley of NSW while the third was at Ensham Mine in Central Queensland. All blasts comprised multiple layers that were blasted in a single drill and blast cycle, with unique designs applied to each layer to achieve different blast outcomes from the various layers.

Jan 1, 2006

By R. W. Boyle

"The concept of using chemical methods in prospecting dates back at least to the middle of the 16th century. Modern methods of geochemical prospecting, however, based on secondary haloes and utilizing trace-element techniques, were first practised in the U.S.S.R. and the Scandinavian countries in the 1930's. After 1945, methods based on soils, stream sediments and vegetation were rapidly developed in the U.S.A., the United Kingdom, Canada, France and other countries.The modern methods of geochemical prospecting owe their rapid development in the 20th century to the following:1.-Recognition of the primary and secondary dispersion haloes and trains that are associated with all mineral deposits. 2.-Development of accurate and rapid analytical methods utilizing the spectrograph and the various specific sensitive colorimetrie reagents, especially dithizone. 3.-Development of polyethylene laboratory ware of all types and the development of resins. This permitted greater freedom of field analyses and reduced the incidence of contamination.4.-Development of gas chromatography. This permitted the rapid and accurate determination of hydrocarbons in petroleum prospecting.Future research in geochemical prospecting should be focused on the following tasks: 1.-Definition of geochemical provinces and their relation to mineral deposits. 2.-Development of methods for discovering large low-grade deposits. 3.-Development of methods for discovering deeply buried deposits. 4.-Further development of methods to outline primary haloes. 5.-Eiucidation and formulation of techniques to relate the size and intensity of anomalies to the grade of the deposits. 6.-Development and refinement of biogeochemical methods, especially those based on indicator plants, chlorotic or toxic effects, and microbiological techniques. 7.-Definition of the types of primary and secondary haloes associated with accumulations of oil and gas."

Jan 1, 1967

By J. W. Oberholzer, C. F. Meyer

The increased use of continuous miners to extract thicker coal seams has necessitated the use of enhanced ventilation systems in the headings. Due to the increased face size, more ventilation is required to effectively dilute the liberated methane down to acceptable levels. If more air is directed to the face an increase in the entrainment of dust creates an increased potential for workers to be exposed to dust. To enable the ventilation systems to reduce the methane levels and the levels of the airborne dust the ventilation systems in the heading have to be carefully designed. The matter is made more complicated through the use of other ventilation methods like jet fans, air-moving sprayfans on the continuous miners and high capacity scrubbers on the continuous miners. To enable the design of a balanced ventilation system in seam heights of over five metres requires methods that consider the system in a three- dimensional manner rather than in a two-dimensional fashion. Through the use of computational fluid dynamics (CFD) coupled with appropriate methods of taking underground face ventilation readings these problems can be solved in a cost effective way. Using computer modelling, ventilation methods can be designed and assessed instead of using costly underground trials to test the alternatives. Use of this system has led to a higher level of ventilation design as well as a more effective method to combat the health and safety hazards in coal mine headings.

Jan 1, 1995

By Balladares V. Eduardo

Most of the arsenic contained in copper concentrates is removed in the gas phase during the smelting and converting processes and, according to recent environmental regulations, it is required to fix it in a solid stable form. In this regards, ferric arsenate has been reported as thermal and aqueous stable compound. Therefore, various alternatives for treating gas containing arsenic were considered in this work. From data obtained at laboratory scale on fixation of arsenic using iron oxide, a new process to treat copper concentrates containing arsenic was evaluated. The effect of temperature, oxygen potential and the sample porosity on the fixation of arsenic contained in a gaseous stream was studied, and the iron oxide converted into ferric arsenate was up to 10%. The obtained results suggest a new alternative for gas treatment with an interesting and attractive technical development. The arsenic was retained as ferric arsenate with thermal and aqueous stability, and it allows a safe disposal keeping the environmental restrictions. The kinetics parameters are used to scale up laboratory results to higher processing rates.

Jan 1, 2005

By E Werner, J J. Donovan, A J. Morris

Coal mining in the Pittsburgh coal seam, in the eastern United States, began in the late-1700s. Since that time numerous mining technologies have been used throughout the basin. Environmental concerns, particularly mine discharge quality, have only been considered since the early-1970s. During the last 20 years, many of the larger underground mines have closed and are now either flooding or already flooded. In order to understand the consequences and potential future effects of this flooding, mine mapping of the basin has been compiled utilising a geographic information system (GIS) with an emphasis on locating barrier pillars between mines. Mine flooding has been monitored at numerous sites utilising pressure transducers and data loggers. These data have been combined with historical data from mining companies and structure contour maps to yield chronological flooding maps of the basin from 1980 to present. Utilising these maps and the indicated flooding rates, future discharge locations have been identified along with estimates of when these discharges are likely to occur. Related work has identified barrier pillar hydraulic conductivities and vertical infiltration rates as a function of overburden thickness. All of this information has been integrated into a groundwater flow model that simulates mine flooding. This model is useful in defining mine to mine interactions as the various mines fill with water, and the testing of various flooding scenarios. The model will be used in evaluating mine discharge rates and evaluating the options for regional mine drainage treatment.

Jan 1, 2003

By Robinson BW, Walker RK

Using a new highly stable automated electron microprobe analyser, detection limits for gold in arsenopyrite have been improved. Using the AuLA emission tine at 40kV and 500nA, a limit of approximately 10gpt is attained in 10- lSmins. Some unusual features of the background need to be taken into account. Several ores containing different levels of gold in arsenopyrite have been examined, and it has been shown that gold is not evenly distributed between grains (some may contain more than 1%, invisible optically), and that the grains containing gold are often zoned. Gold may be released from the arsenopy rite by weathering or by heating in an inert or slightly oxidising atmosphere.

Jan 1, 1989

By T. Sharma, T. C. Rao

Laboratory studies have been carried out on acid leaching as a possible route for the extraction of potassium from glauconitic sandstone. Leaching efficiencies with sulphuric, hydrochloric and nitric acids were investigated. The effects on potassium dissolution of temperature, concentration and type of acid, stirring speed and leaching time were also studied. The results show that it is possible to recover 87.5, 93 and 85% potassium with 5 M H2SO4, HCl and HNO3, respectively. During the initial stages of the sulphuric acid leaching process the chemical reaction at the mineral surface is the rate determining step, whereas during the later stages diffusion through the product layer is rate-controlling. Overall, the process follows a mixed-control model that includes both chemical reaction and diffusion. The activation energy for the dissolution of K was found to be in the range 25.79-106 kJ/mol.

Jan 12, 1992

By J. R. Thoenen

[Since the publication of the preliminary report on this subject in July, 1927, (The Wire Saw in Slate Quarrying, Preliminary Report, Serial No. 2820, by Oliver Bowles) the wire saw has been in constant daily operation at the quarry of the Colonial Slate Company. Luring this time between twenty end thirty successful cuts have been made varying in length from forty-five to ninety-two feet and in depth from six to ten feet. No accurate time records have been kept on these cuts but they have totaled over 12,000 sq. ft. of area and required 19,000 lineal fact During these cuts the average speed of cutting has risen from the 12.8 sq. ft. per hour obtained in the original recorded tests to between 15 and 20 sq. ft. per hour, with the present rate running very close to 20 sq. ft. per hour at this quarry.]

Jan 1, 1928