Search Documents

By John W. Brauns, David H. Orr

9.1-1. Description and Basic Function. A conventional railroad haulage system for a surface mine performs the function of transporting the ore and/or waste out of the pit to a crushing plant or dump. Trains consisting of a locomotive and gondola or side-dump care suitable for loading by power shovels are used. Gondola cars are restricted to hauling ore as a rotary dumper is required to unload them. Side-dump cars are more versa- tile, being satisfactory for carrying both ore and waste; but because of their additional dumping mechanism they are likely to be more expensive to maintain (12). Also they weigh up to two times as much as a flat-bottom car of the same capacity, and, therefore, fewer cars can be hauled per train. Standard-gauge track is most commonly used. Track systems incorporate temporary track of low quality in areas where moves are frequent and permanent track of high quality on main lines. Rail haulage enabled open pit mining to establish its reputation, for efficiency. Prior to World War II it was the principal type of transportation used in large pits. Other successful surface mine haulage methods have been developed since that time. These have served to supplement railroad transportation, permitting selection of a method that is best adapted to the peculiar requirements of each mining project. 9.1-2. General Applicability and Controlling Physical Conditions. For handling rough rock, the shovel-train system is unexcelled (6). The ideal application is in a physically large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transported than will any other haulage method. Relatively gentle

Jan 1, 1968

By H. H. McGregor

Introductory remarks by author When Mr R. C. J. Goode suggested preparation of a paper in the area of manpower utilization in South Africa, I was, while keen to accept his invitation, somewhat hesitant for two reasons. Firstly, I recognized the great difficulty of making a factual contribution, because of the lack of really relevant statistical information available, the fact that much of it is out of date, and the difficulty of researching and co-ordinating it and of evaluating a statistically sound resultant viewpoint. Experience in the actual preparation of this paper has done nothing to change my view in this respect. Secondly, it is obvious that a paper presented to a meeting of this Institute, by a member of it, would be expected to devote considerable attention to the subject in the mining industry. I am not directly employed by the mining industry, although my company has carried out extensive assignments for various sectors of it both in this country and in other parts of the world, since the 1939-45 war. I am more conscious than most of the tremendous technical and managerial skills at the disposal of the industry in this country, and consequently am equally conscious of the hazards of publishing facts and figures which might be taken to indicate any criticism of performance. I am aware that some of the information that I am about to present may indeed generate comment, and possibly even critical comment. I would like to be regarded therefore in presenting this information, as a member of the group, rather than an external critic. Under these circumstances, comment can only be constructive, and this is my earnest hope. The contribution of my paper, if contribution there is, will I hope be in the area of assessing labour productivity in mining, and in secondary industry in such a way that the performance of each against its own past results is comparable. This task has not for the present been to my knowledge attempted, and in advance I wish to take out authors' insurance against legitimate criticism from professional economists and others, by stating that I am well aware of possible short-comings in the arguments. Nevertheless I believe that under the circumstances I have, with the important assistance of several people, been able to take the subject further than has been the case in the past. Finally, I have related productivity in the mining industry and in secondary industry to a target of productivity in the Republic of South Africa. I was fortunate recently in being able to attend a series of lectures by a prominent economist in America. He introduced his subject by calling it 'A broad survey of macro-economics'. Perhaps I might be permitted to describe my paper, in the same idiom, as 'The macro-management of labour'.

Jan 6, 1970

By Joe D. Mitzel

The Indian Head fine has been in existence since 1922. For over 56 years there have been North Dakota people mining coal at this same location. The area affected will fit inside a circle 5 km in diameter, and the coal is lignite. The seam thickness has varied from 2.4 m to 3.65m, and the overburden from 6 m to 30 m in depth. me Lignite coal which is being mined at the Indian Head Mine is from 15.8 x l0 6 to 16.7 x 10 6 J per kg; it has a moisture content of 33 to 38%; an ash content of 5 to 10%; and a sulfur content of from 0.5 to 0.7%. The moisture content and the fact that we crush the coal co a top size of 14 cm x 0, are two of the characteristics or the product which cause it to freeze and remain inside of the railroad cars on the slope sheets. The market for the coal initially was almost entirely local coal sales. That is, coal was sold to people in the area who used the lignite to heat their homes, stores, offices, schools, and churches. Back in the early 1920's, there were no stoker-fed boilers, or pulverized fuel boilers, as we have in today?s marketplace. Basically, all of the coal was sold as lump coal, pieces about 30 to 35 cm square, to be used in furnaces: and nut coal with a top size of about 7.5 cm to 10 cm to be used in the old kitchen cookstove. All of the coal fines, less than 5 cm, were screened out and layed onto a pile. There was no market for the smaller sizes of the lignite coal. It has been our experience that when the coal is in lumps or chunks larger than 7.5 cm to 10 cm, there is a very slight possibility of freezing. That is the chunks themselves freeze, but by their nature, they do not cling to one another or form large masses of frozen material which are difficult to remove from the slope sheers of the railroad cars.

Jan 1, 1980

By Derek. C. Arnold

In order to meet increasing demands for water supply in the next millennium, the Government of the Hong Kong Special Administrative Region have identified the need for a major new water treatment and transfer scheme. The project now under construction will comprise a 1.2 km long raw water aqueduct, a major new 0.25million cubic metres per day water treatment works (with space for upgrading to 1.2Mm³/d), a 12.1 km long treated water aqueduct and a primary service reservoir. In order to meet increasing demands for water supply in the next millennium, the Government of the Hong Kong Special Administrative Region have identified the need for a major new water treatment and transfer scheme. The project now under construction will comprise a 1.2 km long raw water aqueduct, a major new 0.25million cubic metres per day water treatment works (with space for upgrading to 1.2Mm³/d), a 12.1 km long treated water aqueduct and a primary service reservoir.

Jan 1, 1999

The purpose of this work is to determine the equilibrium-state of the aqueous-solution which is produced by the leaching processes, including natural weathering of pyrite minerals. The latter can lead to acid-mine-drainage (AMD). The ferric iron species (Fe3+) resulting from bacteria-catalysed oxidation of ferrous iron (Fe2+), in the presence of water and air, is known to bring about steady-dissolution of minerals chalcopyrite (CuFeS2), sphalerite (ZnS), pyrite (FeS2), and so forth. Good-aeration, relatively high-porosity and sufficient bacterial activity tend to promote leaching in waste-rock-dumps. The composition of the aqueous-phase that accumulates in the pore-space (or in open-pits) is of practical interest as it would strongly influence the leaching of both sulfide and non-sulfide minerals. Since the reactions among the various ionic species occur relatively fast, the solution-phase may be regarded as approaching a state of virtual-equilibrium and it is possible to determine by computation the respective concentrations of the many dissolved species. For the Cu-Fe-H-O-S system, these species may include: H+, Fe2+, Fe3+, Cu2+, HSO4-, SO42-, OH-, CuSO4o, H2O, Fe(OH)+, Fe(OH)2+, Fe(OH)2+, Fe2(OH)24+, Fe(SO4)+, Fe(HSO4)+, Fe(HSO4)2+, and Fe(SO4)2-. The aqueous-system which may be constituted from appropriate mole-quantities of H2SO4, FeSO4, Fe2(SO4)3, and CuSO4 is in fact the result of various natural processes (reactions) and due respect must be accorded to the extents of these reactions. The present model computes the equilibrium molalities of the foregoing ionic and neutral aqueous species, using the iterative equilibrium constant method that ensures strict-adherence to charge-balance and elemental molar-balance constraints. The dissolving sulfide-minerals (FeS2, CuFeS2) consume Fe2(SO4)3, H2O, and O2 and yield FeSO4, H2SO4, and CuSO4 while the aqueous-phase tends to become progressively acidic (declining pH) reflecting the gradual increase in the extents of sulfide-dissolution reactions. The equilibrium-state of the solution-phase is computed for specific set of values for the extents of respective reactions. The temperature and pressure of the system are 25¦ C (298.15 K) and 101.325 kPa (1.0 atm), respectively. The mica-like minerals such as the biotite [H2K(Mg,Fe)3Al(SiO4)3] tend to consume much of the H2SO4(aq), with the extracted K+, Mg2+, Fe2+ and Al3+ ionic species accumulating in the solution. The precipitation of the jarosites (potassium, hydronium, or ammonium) contributes to the removal of ferric and ferrous species from the solution-phase. In the present work, the emphasis is on predicting the compositions of the aqueous- and condensed-phases with advancing time or increasing æextent of reactionÆ. The results of such calculations are compared to published data on raw AMD (acid-mine-drainage).

Jan 1, 2008

By C. H. Jr. Herty

The results of a study of the open-hearth process from the physicochemical view-point are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon, and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. THE effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styri1 from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900° F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,3 Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 2, 1926

By T. M. Barczak

Many of the support concepts currently used in the United States originated in South Africa. These products include the Hercules Crib1, Propsetter, MX Prop, Rocprop, and Spider Prop. Another recent development has been the introduction of hydraulic prestressing units, such as the Jackpot system, to various U.S. standing support systems. Several other prop-type supports with similarities to systems used in South Africa are in use in U.S. coal mines. Some exciting new developments that improve the installation and yield performance of props are also underway. In addition to prop-type supports, crib-type supports and single-unit systems such as the Can support are also frequently utilized in longwall tailgates in the U.S. The goal in U.S. support development is to enhance roof support capability while alleviating material handling barriers to reduce injuries associated with support handling and installation. Support products are generally full-scale tested at the National Institute for Occupational Safety and Health (NIOSH) in the unique Mine Roof Simulator load frame. The performance testing protocol is designed to simulate the full range of load conditions that occur in underground mining to identify the performance deficiencies and limitations of the support products. Once the products complete the performance evaluation, they are implemented into the NIOSH Support Technology Optimization Program (STOP). STOP is a window’s based software program that was developed by NIOSH for facilitating the design of standing roof support systems. STOP has become an industry standard to compare the performance capabilities and facilitate the application of these support products into various mining conditions. The purpose of this paper is to provide an overview of the support design and application philosophy in the United States.

By N. Plint, E. T. Pinkney

Copper segregation developments within the Anglo American Group are described with particular reference to the work of the TORCO Project Team. Some radical differences have been adopted in the mechan-ical approach as compared with methods used by previous workers. Most important among these are the following: (1) The heating unit is a fluidized-bed roaster. (2) A moving bed segregation chamber is used in which a packed bed of heated ore, to which reagents have been added, moves slowly downwards under gravity and is discharged at a controlled rate by means of a suitable valve mechanism. (3) The quantities of reagents used (sodium chloride and some form of carbon) are only a small fraction of those recommended by other investigators. (4) Retention times of only 2 min have been satisfactory for the complete segregation of many types of ore. Project TORCO is the code name given by Anglo American Corp. of South Africa, Ltd., to the investigation undertaken in Zambia to develop a plant capable of treating large tonnages of refractory copper-bearing ores by the segregation process. The process has now been under investigation for six years (1960-66) and during that period work has progressed from bench-scale laboratory tests through small-scale pilot-plant work to a 500-tpd commercial pilot unit. Test work has been carried out mainly on the ores of the Zambian Copperbelt and results have been encouraging. Recoveries on the order of 90% have been obtained on all Copperbelt ores tested with high concentrate grades. PRELIMINARY INVESTIGATION Laboratory scale segregation test work on Nchanga banded sandstone ore and oxidized ore from Kansan-shi was originally conducted by Professor Maurice Rey. SociCtC Miniere et Mktallurgique de Pefiarroya, in 1957. Both ores responded favorably to the process. In November, 1960, the consulting engineers of Anglo American Corp. of South Africa, Ltd., initiated preliminary investigations on the application of the segregation process to Copperbelt ores. In early laboratory work, samples were heated in a closed, externally heated tube furnace for one hour at temperatures ranging from 800 to 830°C. The free moisture content of the ore feed was 4% and reagent additions were 0.5% salt and 1.0% coal. Both salt and coal were pre-crushed to -48 mesh Tyler.* All samples except an ore from the Bancroft mine responded well to the process and recoveries of over 90% were obtained. The presence of dolomite was responsible for the relatively poor recoveries from the Bancroft ore, as tests on one of the other ores with additions of calcite or dolomite confirmed. Recoveries dropped from 94 to 45% Grades of all the rougher flotation concentrates produced were low at 10-15% copper. The laboratory investigation was then followed up on a pilot-plant scale. An attempt was made to carry out the segregation process in a coal-fired 5-ft-diam fluidized-bed roaster. The feed consisted of a banded sandstone from Nchanga to which 0.5% sodium chloride had been added. Reducing conditions were maintained in the roaster by the addition of coal in excess of that required for heating the feed. The excess coal and added salt constituted the segregation reagents and the temperature of the bed was held at approximately 750°C. Recoveries of copper and grades of concentrates were low. The reasons for lack of success were: (1) The reaction is a gaseous one and a fluidized-bed roaster is therefore unsuitable as a segregation unit. (2) Coal in excess of that required for heating was introduced into the fluidized bed and under these conditions some of the copper would be reduced in situ. The term "reduced in situ" is used here to describe any copper mineral reduced to the metallic state in its original site within the ore particles. If this copper is to be recovered by subsequent froth flotation it must first be liberated from the gangue by grinding or some other method which, in practice, is usually not feasible on ores of this type.

Jan 1, 1969

By José Robles

En 1922, se instalaron las primeras compresoras de 80 H. P para la obtención de gasolina natural en Brea y Pariñas, a través de la utilización del gas producido en los separadores de baterias de crudo. Sin embargo, esta cifra se elevó a 22, 000 h.p, demandando una red de 5 plantas de compresión-absorción que funcionan en conjunto con una Planta Central de destilación-estabilización y dos estaciones compresoras auxiliares. En este punto, la intención del trabajo es mostrar el proceso de logro de gasolina natural en el Perú, y el sistema de distribución de gas seco, a partir de la conexión con pozos productores, las plantas de compresión-absorción, equipo de compresores y el equipo de enfriamiento general.

Jul 20, 1955

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By Steve Dillingham

In recent years, there has been a trend toward increasingly demanding blasting standards being enacted by local and regional regulatory authorities. The objective of this paper is to alert blasters of the difficulties that are created for blasting projects as a result of these restrictions, as well as the steps that can be taken to minimize future conflicts.

Jan 1, 1995

By JOHN DUNFIELD

Good quality sphagnum peat bogs occur across Canada in areas of ample rainfall and cool, temperate climates. Early peat production techniques were restricted primarily to hand digging blocks of peat and piling them up to be dried by sun and wind. Suburban de velopment in the 1950s and the concomitant spread of home gardening triggered a dramatic growth in peat demand; labour costs rose in the same period. Peat production techniques had to alter accordingly. The three mechanical inno vations attempted were hydraulic mining, mechanical block digging and vacuum harvesting. Of these, the last method pro ved the most successful in Canada and is used to harvest 80% of Canadian peat production. Escalating transportation costs are the most important feature affecting future development of the Canadian peat industry.

Jan 1, 1984

By W. M. McKewan

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. A 2-in-diameter 6x25 fiber core rope was degraded on a bending fatigue machine. This was the first in a series of tests on rope of this construction and size. Baseline testing at the laboratory was reported in an earlier publication. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that as a wire rope nears the end of its useful life, deterioration and the consequent loss of rope strength increase at an accelerated rate.

Jan 1, 2010

By R L. Brathwaite

The epithermal gold-silver deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Epithermal deposits consist of quartz veins, quartz vein stockworks and hydrothermal breccias that are mainly hosted in subaerial andesitic or rhyolitic rocks of Tertiary age. The deposits were formed at depths of typically less than 1 km and at temperatures between 180¦ and 320¦C, although ore grade mineralisation was generally deposited at less than 270¦C.   In New Zealand, epithermal deposits occur in association with late Cenozoic volcanic rocks in the Northland, Coromandel and Taupo volcanic regions. All of the past and present gold production, estimated at greater than 380 t (along with 1300 t Ag) comes from the Miocene-Pliocene Coromandel Volcanic Zone, where about 50 epithermal gold-silver deposits occur over a 200 km long belt. In Northland, silver and mercury have been produced from hot spring type epithermal deposits, and several gold-silver prospects have been identified. Ore grade gold-silver mineralisation is currently being deposited in several active geothermal fields of the Taupo Volcanic Zone, and extinct geothermal systems occur on the western side of the zone. The active systems have provided natural laboratories to help understand the processes of epithermal mineralisation.

Jan 1, 2005

By S. B. Keith

Cerro de Pasco Corporation operates five large base metal mines in Peru having a combined production of some three million tons of ore a year. An integrated complex of concentrators, smelters and refineries produces annually about 25,600 short tons of copper, 48,100 short tons of lead, 60,500 short tons of zinc metal, 102,300 short tons of zinc concentrate, 8,272,000 ounces of silver and substantial amounts of bismuth, cadmium and selenium. Geology plays an important role in these operations. The organization of detail geologic work in and around the Cerro mines was set up by John M. Boutwell in 1918 and a geology department was established in 1920. Growing through the years, the department technical staff now numbers over thirty men and. their work covers all phases of geological investigations. Many outstanding geologists of the past and present, too numerous to name here, have studied and contributed to the knowledge of the deposits and the ever growing list of Cerro "alumni" must rival that of any other mining organization. Numerous papers on the geology of Cerro's mines can be found in the technical literature and several doctoral theses have been presented on Cerro subjects as indicated in the attached bibliography, Specimens of Cerro's ores can be found in museum, college and university collections throughout the world. Yet, as with all mines and mining districts, the geologic knowledge of Cerro's deposits in Peru is being revised and added to constantly. This presentation cannot hope to cover adequately all the phases of the geology and mineralization. For a more complete background and discussion of the mine you are referred to the bibliography. Here I shall outline only briefly the more important geologic features and describe some of the newer developments of recent years The credit for the data presented here belongs to the many geologists who have worked or are now working for Cerro de Pasco Corporation, but I must assume sole responsibility for any omissions or variations in the interpretation of their work.

Jan 1, 1965

By D. Zaharaki

In the present experimental study the geochemical stability of inorganic polymers was studied by immersing them in various solutions (distilled water, seawater and 0.5N HCl) for a period of 7 months. Inorganic polymers were synthesised by mixing ferronickel slag with kaolinite, potassium hydroxide and sodium silicate solution. The cement like paste was heated at 80 °C for 48 hours and left for curing at room temperature. Their structural integrity was assessed by compressive strength testing after subjection to freeze-thaw cycles as well as high temperature heating. XRD studies were carried out in order to identify new formed phases and provide useful information regarding the progress of the mechanisms involved.

Jan 1, 2008

By J. Oré Iwanaga

El presente texto señala el uso de geocontenedores como una alternativa en la deshidratación de lodos líquidos ( relaves) a través del programa MATLAB que permite la determinación de los parámetros de diseño más importantes. La ejecución del programa se realizó en la planta concentradora de la Compañía Minera Raura, ubicada en la cordillera occidental entre Huánuco y Lima, sierra central del Perú donde se estableció la presión de bombeo (Po) y resistencia del geosintetico (T),a partir de datos conocidos como: perímetro (L) y peso específico del lodo líquido.

Jul 1, 2014

By Leonard L. Fischman

It is important to define "adequacy," and the most useful definition is a continuing availability of mineral materials under cost and other conditions which imply no significant burden on the achievement of otherwise attainable levels of consumption and well-being. For current decision making, it is sufficient to consider adequacy just to the end of the century, with some regard being given to then remaining mineral inventory. A comparison of cumulative demand projections to the year 2000 with already identified reserves ( economically recoverable amounts in known deposits) suggests little reason for concern with world adequacy of iron ore, aluminum, manganese, chromium or potash. Conservative estimates of "prospective" reserves (amounts producible at today's prices, but yet to be discovered) suggests that there are ample quantities of virtually all other mineral resources as well. A probable exception is oil and gas, of which there may be scant amounts remaining after the turn of the century. However, there is an evident sufficiency of substitute forms of energy, though it is difficult to see just where developing technology will take us. The critical questions have to do with the increasing dependence of the industrialized countries on external sources of supply , coupled with a new international politic s which complicates the problem of insuring timely development of, and access to, remaining deposits. In this context, Canada, a still mineral-rich nation, is in one of the more favorable positions.

Jan 1, 1977

By E. H. Dix

All commercial aluminum contains small percentages of copper, iron, and silicon as unavoidable impurities. The purest metal obtainable commercially, special grade high purity ingot, contains a maximum of 0.50 per cent. impurities of which the usual minimum amount of copper is 0.01 per cent.; silicon, 0.12 per cent.; and iron, 0.20 per cent. This grade is too costly for most purposes. The two standard grades, Nos. 1 and 2, containing a minimum of 99.0 and 98.0 per cent. aluminum, respectively, are more generally used. Other grades of secondary aluminum often contain as high as 3 or 4 per cent. of impurities, which include 1 per cent., or more, of zinc. Specifications for high-grade aluminum-casting alloys generally allow a maximum of 1.7 per cent. for total impurities. The S. A. E. Specification No. 33, which is intended to cover alloys made from secondary aluminum ingot, gives the iron maximum as 1.5 per cent. and the maximum for silicon (including manganese and tin) as 0.75 per cent. The effect of even relatively small amounts of impurities on the physical properties of ingot aluminum is shown by the following cornparison of two lots of aluminum, which may be taken as representative of special grade and grade No. 2 ingot, respectively. AnalysEs Special Grade, Gbade No. 2, Per Cent. PeR CBnt. Copper................................. 0.01 0.32 Silicon................................. 0.12 0.32 Iron................................... 0.42 0.82 Aluminum.............................. 99.45 98.54

Jan 1, 1923

By E. H. Dix

All commercial aluminum contains small percentages of copper, iron, and silicon as unavoidable impurities. The purest metal obtainable commercially, special grade high purity ingot, contains a maximum of 0.50 per cent. impurities of which the usual minimum amount of copper is 0.01 per cent.; silicon, 0.12 per cent.; and iron, 0.20 per cent. This grade is too costly for most purposes. The two standard grades, Nos. 1 and 2, containing a minimum of 99.0 and 98.0 per cent. aluminum, respectively, are more generally used. Other grades of secondary aluminum often contain as high as 3 or 4 per cent. of impurities, which include 1 per cent., or more, of zinc. Specifications for high-grade aluminum-casting alloys generally allow a maximum of 1.7 per cent. for total impurities. The S. A. E. Specification No. 33, which is intended to cover alloys made from secondary aluminum ingot, gives the iron maximum as 1.5 per cent. and the maximum for silicon (including manganese and tin) as 0.75 per cent. The effect of even relatively small amounts of impurities on the physical properties of ingot aluminum is shown by the following cornparison of two lots of aluminum, which may be taken as representative of special grade and grade No. 2 ingot, respectively. AnalysEs Special Grade, Gbade No. 2, Per Cent. PeR CBnt. Copper................................. 0.01 0.32 Silicon................................. 0.12 0.32 Iron................................... 0.42 0.82 Aluminum.............................. 99.45 98.54

Jan 1, 1923