Search Documents

By W. A. Backofen, F. de Kazinczy

FRACTURING under conditions of particular interest is identified with the junction of curves relating tensile yield and fracture stresses to test temperature; the intersection point gives the lowest stress, for brittle fracture (at the ductility transition temperature). An expression for is found in Cottrell's brittle-fracture analysis, Eq. [15],1 while measurements of this stress and temperature have been reported for a low-carbon steel heat treated to differ-

Jan 1, 1962

By J. G. Thompson

THE methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value represent-ing the sum of the oxygen contents of several or all of the oxide con-stituents present. With such diversity in the principles and. aims of the different groups, it is not surprising that concordance of results by differ-ent methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the vari-ous methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metal-lurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1936

By J. P. Rider

Health surveillance efforts indicate that the development of lung disease and overexposure to respirable dust in underground coal mires continues to afflict mine worker. Results from the most recent round (1992 - 1996) of the Coal Worker's X-ray Surveillance Programs indicate that approximately 8% of the examined miners who had at least 25 years of mining experience were diagnosed with Coal Worker Pneumoconiosis (CWP) (category 1/0+). During the period between 1995-1999, mine operators and MSHA inspectors collected 9968 and 1365 dust samples respectively, from longwall designated occupation (DO) personnel. Analysis of these samples showed that 1970 (20%) of the mine operator samples and 25.8 (19%) of the MSHA samples5 exceeded the 2 mg/m3 dust standard. The continued development of CWP in coal mine workers and the magnitude of respirable dust over-exposures in longwall mining occupations illustrate the need for improved dust control technology on longwalls. Figure 1 illustrates the major longwall dust sources as determined in the early 1990's.4 This article describes the ongoing research to find ways to minimise shearer dust levels as a function of changes in dust control parameters, and research to determine the impact of high air velocities on shield dust entrainment.

By Neville G. W. Cook

The ultimate goal in rock mechanics is to make quantitative predictions of the response of rock to changes. Measured and calculated values of changes in displacements or temperatures in the rock for six different field experiments are compared using linear regression. When values of the mean compressive stresses are large compared with the values of the deviatorial stresses, linear elasticity, using values for Young's modulus from laboratory tests, provides a good predictive model. However, if the values of the mean compressive stresses are small compared with those of the deviatorial stresses the behavior and response of the rock, though systematic, is not linear. Linear heat conduction provides good predictions of changes in rock temperatures but thermal displacements are not predicted well by linear thermoelasticity.

Jan 1, 1982

P. E. McKinney,* Washington, D. C.-Observation made after examination of a number of defective gun forgings, together with a history of their manufacture, has strongly suggested that so-called "flakes" and woody or fibrous fractures are not necessarily analogous and are often caused by entirely different conditions. While some flaked bars may show fibrous areas in the fracture, it does not necessarily follow that the conditions causing these areas are the same as cause the fibrous, or so-called laminated, structures so commonly met in gun forgings subject to transverse tensile test; the fibrous structure formed in some flaky bars are merely incidental to the conditions causing the flakes. It is believed that the so-called flakes, or bright silvery spots, are mainly due to inherent physical defects in the steel, which existed at the very origin of the steel, rather than metallographic defects caused by subsequent irregularities in mechanical or thermal treatment. While great care in forging and treatment may, in a measure, tend to overcome the evil effect of the defects, with many heats of ingots, no such precautionary measures are needed to produce perfect forgings- and with such heats of steel it would be impossible, no matter how carelessly handled, to produce intentionally a forging containing the defects commonly known as flakes. It has been found possible, on several occasions, to actually predict flaky forgings from an inspection f the ingot after it had solidified, and in such cases no amount of careful forging or heat treatment would prevent the occurrence of such defects in the forging. The inspection of the physical condition of the ingot, and especially the character of the shrinkage on. the top of the ingot, has been given too little thought and study in this connection.

Jan 5, 1919

By Eder Zegarra Salazar

El presente trabajo tiene como finalidad de ejecutar un proyecto Glory Hole San Gerardo, cuyo objetivo es desarrollar un RAMP UP de 300, 1,000, 1,500, 2,000, 3,000, 4,000, 5,000 TPD de mineral, como resultado de este proyecto de ampliación será necesario construir nuevas instalaciones de apoyo y de servicios a la mina, tales como talleres, almacenes, polvorín, ore passes, campamento etc. Estas deberán ubicarse en una zona que no afecte la futura expansión del proyecto con el método de explotación a tajo abierto.

Sep 1, 2017

J. E. Stead, Middlesborough, England (communication to the author): Prof. Howe's valuable paper on cast-iron brings forward most prominently the correct explanation of the part played by combined carbon in pearlite and cementite, in determining the strength and hardness of cast-iron. On a previous occasion I haveoshown that castings made by melting a white Cleveland iron and glazed iron, one containing 1.5 and the other from 4 to 5 per cent. of silicon, and each about 3 per cent. of carbon, were stronger than those made of ordinary foundry-iron; the difference in the final castings being a differ-

Jan 1, 1902

It is a commonplace of our industry that prices of most minerals have been historically weak during the 1980s. The International Monetary Fund's index of prices of metals fell 25 per cent between 1980 and 1982, rose slightly in 1983, and has since fallen further. In December last year it was 37 per cent below its 1980 average. The few temporary exceptions to the mineral industry's malaise highlight the excess capacity, which largely explains the weakness of prices. The industry has painfully come to recognise that more satisfactory prices will not be restored until supply capability and demand move back into better balance. Mine capacity was installed in the expectation of much faster growth of demand than has occurred. For a variety of reasons mine and plant closures have been insufficient to restore equilibrium to the market-place. The industry may, therefore, have to resign itself to continued weak prices for some years more, at least by the yardstick of the 1970s. Growth rates of demand have slackened off in line with economic activity, and in response to continuing substitution and technological improvements. To the extent that the recent weakness of oil prices stimulates the industrial countries' activity, demand for non-fuel minerals may grow faster than most forecasters now predict. It is, however, much too early to say how long the weaker oil prices will persist, and even more difficult to estimate their probable effects. In typical post-war business cycles the usual response to recession was to batten down the hatches, and ride out the storm. Sooner or later, and probably sooner, demand resumed its previous trend path, and prices recovered. The market, in effect, bailed mines out of trouble; the more efficient could make attractive pre-tax profits whilst even the poor to mediocre could earn a satisfactory living. Prices rose at least as fast as general inflation, and in the early 1970s much faster. In retrospect those price rises of the early 1970s were historically abnormal but they did not appear so in the prevailing inflationary climate of the time. When the market failed in the early 1980s many of the hardest hit companies looked for scapegoats.

Jan 1, 1986

By M R. Lane, M L. Cramer, N P. Wines

Increasing attention is being focused by regulators and industry on the residual environmental liabilities associated with mining projects following site relinquishment (termed surrender in Queensland). Even sites that have been rehabilitated to a high standard and to the satisfaction of the regulator are not completely risk free and may require some degree of ongoing management. As well as ongoing monitoring and maintenance costs, considerations should include how costs associated with potential risk event occurrence can be quantified and, if considered material, how provisioning should be undertaken to minimise the risk to the state and to taxpayers. In Queensland for example, once a resource site is fully rehabilitated and meets its environmental authority conditions or rehabilitation completion criteria, the tenure and environmental authority can be surrendered. During the surrender process any ‘residual risks’ resulting from the use of the site for the resource activity must be considered, and, if requested, a payment given to the government to cover any ongoing management and risk costs. Accent Environmental, in conjunction with Lane Associates, was engaged by the Queensland Government as part of the government’s financial assurance framework reforms to develop an innovative, ‘one-size fits most’ Residual Risk Calculator for the Queensland resources industry. The calculator is an Excel-based tool that uses detailed user inputs to estimate post-surrender management requirements and liability at resource sites. If residual environmental risks associated with rehabilitated mine sites can be identified, quantified and managed through pragmatic regulatory tools and effective provisioning, site relinquishment/surrender can be achieved without compromising environmental and social outcomes or exposing the state to unreasonable financial risk. The effective management of residual risk can also help facilitate operations as well as relinquishment/surrender of sites where a ‘walkaway’ solution may not be otherwise technically feasible.

Aug 2, 2023

By AIME AIME

ON Tuesday afternoon, Feb. 17, a large and interested audience gathered in the auditorium of the Engineering Societies building to take part in the gold supply symposium that had been arranged for by the Mining Geology Committee. Waldemar Lindgren presided over the gathering and after brief introductory remarks on the international situation as regards lead, silver and gold, called on John Wellington Finch to present an oral abstract of the paper, "Sources and Trends in Gold Production," by R. J. Grant, director of the Mint, and. J. B. Knaebel. This ' paper reviewed the gold production of the world, by countries, since 1845, from the statistical viewpoint, leaving to the later speakers discussion of the statistics.

Jan 1, 1931

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By W. L. Phillips

Nickel alloys containing approximately 0.5, 2.0, and 6.0 at. pct of Os, Pd, Ru, and Rh were Prepared by vacuum melting. Tension tests were carried out at 25°, 500°, 800°, and 1000°C; stress-rupture tests were carried out at 650° and 800°C. The room- and elevated-temperature tensile strength, as well as the stress-rupture life, increased for the same atomic percent in the order palladium, rhodium, ruthenium, osmium. The ductility decreased with increasing concentration or temperature for a given concentration. The results are discussed in terms of solid-solution theory. BOTH solid-solution strengthening and weakening have been observed in alloys. The simple rules which have been suggested to explain alloy strengthening are subject to several exceptions and deviations based on atom size and valency effects. The purpose of the present investigation was to extend the knowledge of the effect of solid-solution alloying on the mechanical properties of several Ni-Pt group metal alloys at room and elevated temperatures. The platinum group metals, osmium, ruthenium, rhodium, and palladium were chosen as the solute elements because of their different valencies and atom sizes. Nickel was chosen as the base material because of the large amount of previous literature available on nickel alloys. EXPERIMENTAL PROCEDURE Grade A Carbonyl nickel powder having the following composition: C, 0.07 pct; Fe, 0.013 pct; Mn, 0.0005 pct; Si, 0.016 pct; Mg, 0.0003 pct; S, 0.003 pct, was purchased from the International Nickel Co. The platinum-group metal powders were purchased from A. D. Mackay Co. The powders were weighed, cone-blended for 4 hr, and vacuum-melted into 1-in.-diam billets, approximately 2 in. long. The ingots were homogenized for 5 hr at 1800°F before being extruded into 1/4-in. rods at 2100°F. The alloy compositions are shown in Table I. Typical impurity values were not significantly different than that of the as-received nickel. All alloys were single phase. The lattice parameter of each alloy after the heat treatment described below is also included in Table I. Each alloy was annealed at 2200°F for 1 hr and air-quenched to comparable grain sizes (ASTM G.S. No. 4-5). The rods were then machined into test samples 0.160-in. diam and 0.750-in. gage length. Tension testing was carried out in an In-stron tension-testing machine at a strain rate of 0.02 in. per in. per min. An extensometer was used to determine the room-temperature yield stress. Stress-rupture testing was carried out in an Arc Weld stress-rupture unit. All testing was performed in air. EXPERIMENTAL RESULTS A) Room-Temperature Mechanical Properties. The 0.2 pct yield stress, ultimate tensile strength, and elongation for all alloys tested at room temperature are plotted as a function of atomic percent solute element in Fig. 1. The ultimate tensile strength for the same atomic percent increases in the order palladium, rhodium, ruthenium, osmium. The yield strength at low concentrations, -0.5 at. pct, increases in the order osmium, palladium, ruthenium, rhodium. At higher concentrations, 3.0 and 10.0 pct, the yield strength increases in the same order as the tensile strength. Both yield strength and tensile strength increase rapidly ini-

Jan 1, 1964

By J. Howard Boyce

INTRODUCTION The Tsumeb Mine is situated in the northern part of South West Africa, approximately 335 air miles north-east of the port of Walvis Bay on the Atlantic Coast, and 240 air miles north of Windhoek, the capital of South west Africa. The mine came into operation in the early 1900's and has operated continuously since then except during the two world warm and the depression years of the thirties, Tsumeb Corporation purchased the property in 1947, installed a new plat, and ham built a modern tom. In addition to the concentrator which began operations in 1948, a copper smelter was started in 1962 and a lead smelter in 1963, Tonnage of ore treated in the concentrator has varied through the years, reaching a maximum of 70,000 tons per month with a current mined tonnage of approximately 50,000 tons per month. Copper concentrates, lead concentrates and zinc concentrates are produced, and for a number of years the production of a germanium enriched concentrate was an important feature of the operation, Both copper and lead concentrates are smelted in Tsumeb, while the zinc concentrates are shipped overseas. Ore change, and the installation of the smelters in Tsumeb have necessitated modifications in the concentrator operation. This paper will describe current plant practice in some detail and will touch briefly on the techniques used from 1954 to

Jan 1, 1970

By Colin Lindsay

"The Collahuasi copper mine, located at an altitude of 4300 meters above sea level in northern Chile, commenced operations late in 1998. The mine is currently the 4‘h largest copper producer in the world and comprises an open pit, a 60,000 tpd sulphide concentrator, a 15,000 tpd oxide heap leach and SWEW plant and a 200 km concentrate pipeline to a port facility.Constructing, commissioning and operating a mine at high altitude presents unique challenges in terms of the performance of both equipment and people. It is important that these be recognized and carefully considered during the feasibility study and the detailed design stages and the success of the Collahuasi project is largely due to this. The plant design incorporates a number of features aimed at mitigating the problems of altitude and the construction methodology also took into account the particular site conditions.This paper discusses the Collahuasi project team’s approach to planning for the remote location and also some of the problems experienced during construction, commissioning and operation.INTRODUCTIONThe Collahuasi mine is located in northern Chile, some 250 km to the south-east of the port of Iquique and 15 km from the Bolivian border. The mine facilities lie between 3800-4300 m above sea level on the Altiplano, the central plateau of the Andes mountains, and cover a total of approximately 95,000 hectares. Although the area is arid, it experiences an average of 150 mm of precipitation annually and weather conditions can be extreme. Temperatures during the day range between -3 to +11 º C and are generally below 0ºC at night, sometimes as low as -20°C. High energy winds are common and humidity is low. Much of the precipitation occurs during the winter as snow but there also occurs a period during the Chilean summer known as the “Invierno Boliviano’’ (or Bolivian Winter) which is characterized by severe electrical storms and rain."

Jan 1, 2001

By Y. Luo

Based on the concept of slope stability analysis, a formula for determining an important parameter required in the mathematical model for the prediction of mining subsidence in hilly terrain has been proposed. The slope geometry and soil physical and mechanical properties of the surface natural slope can all be considered in the formula. Incorporation of this new formula into an existing mathematical model provides an integrated approach in studying ground movement in hilly regions.

Jan 1, 1998

By A. B. Kinzel

A PREVIOUS study1 of the relations of impact strength to inclusions showed that the dynamic strength of steel is lowered by the presence of visible counted inclusions, but that other factors comprised in the term "body" have a marked influence. The previous work was carried out on selected steels from a single source, so that the body factor was purposely minimized, but even under these conditions it was found that inclusion counting or the use of the commercial inclusion rating is not satisfactory. The tensile-impact test, however, was indicated as a satisfactory measure of dynamic strength. It was further suggested that the tensile-impact test should be so standardized as to be suitable for use in specifications, and that the hardness factor should be worked out over a sufficient range to admit ready commercial use of the tensile-impact test. In accordance with these suggestions, and in view of the fact that the steels reported in the previous paper were selected and treated so as to have a minimum variation in body, hardness and structure, further work has been performed on a variety of steels which are not limited by these conditions. The word "body" is used here for want of a better term. It is simply a convenient expression which comprises the effect of the various unknown factors that modify the dynamic strength of the steel. Thus at our present state of knowledge, the writers have chosen to consider hardness, structure and counted inclusion content as factors not comprised in the term "body," and such factors as raw materials, process of melting, fabricating, etc. as comprised in the term "body." Numerous grades of steels made in several ways have been taken from different sources and have been heat-treated to varying hardness by normalizing and by quenching and drawing. The results, therefore, may be considered to be generally applicable to current engineering steels. A certain limitation with respect to the hardness at which steel should be

Jan 1, 1931

By Nicholas J. Grant, Italo S. Servi

Extensive data of minimum creep rates and rupture times for high purity and commercial aluminum confirm the existence of a transition range from the low temperature-type to the high temperature-type behavior. The data are analyzed in line with the suggested theories of deformation of metals. CONSIDERABLY more work has been done on the rupture and creep behavior of commercial alloys than on the less complex, high purity metals. As a result, certain fundamental behaviors are overlooked. One of the lesser known variables affecting the high temperature behavior of metals is the impurity content (or alloy content). Impurities are known to affect strongly the recrystallization temperature, electrical resistivity, and other properties of metals, but the effect on creep and other high temperature mechanical properties has been determined for very few materials. In view of these facts aluminum appears to be a fairly ideal metal, since it is available in a wide range of purity contents from 99.995+ down through the 2s (99.0 + Al) and 3s (1.2 Mn) grades in small steps. It is highly resistant to oxidation and other surface instabilities, leaving recrystallization and grain growth as virtually the only instabilities. Control of grain size is also well standardized. Limited data on the creep of aluminum have been obtained by Dushman et a1.l for high purity aluminum; by Sherby2 on 2s aluminum of variable grain size; and by Dorn and Tietz³ on cold-worked 3s aluminum. Experimental Procedure The apparatus consisted of a constant stress, creep testing unit similar to the type described by Hop-kin.' The specimens were held at temperature for 30 min before loading. The loading time was less than 2 min. Factors affecting the accuracy of the data were: 1-—the temperature gradient and control, ± 3°F; 2-the stress determinations, ± 1.5 pct; and 3—elongation measurements (1 in. gage), ? 0.001 in. Three grades of aluminum were tested: 1— high purity (99.995 pct Al), 2—2s (99.3 pct Al), and 3—3s (98.2 pct Al). The spectrographic analyses of these materials are reported in Table I. The specimens were annealed then electropolished in a perchloric-acetic mixture before testing. Data on heat treatments and grain size obtained appear in Table 11. The entire creep curve was determined for almost all of the tests. A few tests were interrupted after the beginning of the third stage of creep, and in these cases the rupture time was estimated. Experimental Results Constant stress creep-rupture testing gives a much longer, more accurately measurable second stage of creep than constant load testing. This behavior is in agreement with the results obtained by Andrade for lead (see Fig. 1). If the test is run to completion, the third stage of creep appears as soon as stress intensification occurs. In the case of specimens which fail in a ductile manner, the stress intensification begins when the sample starts "necking". This differs from the "high temperature brittle" specimens in which the stress intensification is caused by intercrystalline cracking. These specimens

Jan 1, 1952

By T. A. McAfoose

As one of the major suppliers of the chestnut Ridge energy center, Rochester and Pittsburgh Coal Company continues the search for more efficient haulage systems. This search is one that is essential in providing coal to the Keystone and Homer City power plants at the most economical cost. These two electrical generating plants located in west central Pennsylvania are part of the energy center which consists of four generating stations. Prior to the time the two stations were put on line, August, 1967 for Keystone and August, 1969 for Homer City, our company made the decision to rely on belt conveyors from the section to the surface to provide for continuous main line haulage. The proximity of these generating stations to proven reserves allow for minimal truck haulage and minemouth setups. With the addition of seven new mines, in the past ten years, revisions have been made on the original setup to interconnect the haulage of several mines to deliver the product by belt to the power plants.

Jan 1, 1979

By Otis M. Clarke

Although most bauxite mined is used to make metallic alu¬minum, more than a million tons of bauxite is used annually in the United States in the manufacture of refractories, chemicals, abrasives, and cement. Raw material requirements are becoming increasingly difficult to meet because high-grade bauxite, required for some uses, is limited. The supply of raw material for high-alumina refractories is most critical because a low-iron bauxite is needed. Although there are substantial bauxite reserves in the world, bauxite suitable for use in refractories is limited to a few districts.

Jan 1, 1977

By Lancucki C. J, Nickson N. M

X-ray diffraction and differential thermal methods were used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis was made of the mineralogy and particle size distribution of eighteen samples from beds in two pits in the Recent sediments in the Adelaide plains, of six white clays developed from the weathering of the Adelaide series of sediments, and of four Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products in the Adelaide area are manufactured from mixtures of these clays, so the mineralogy and particle size distribution was determined of eighteen clay mixtures used to make red bricks, cream bricks, facing bricks, pipes and tiles.Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.INTRODUCTIONIn this investigation an account is given of the clay mineralogy and particle size distribution of some ceramic clays from the Adelaide area. The clays are used in the manufacture of structura,l clay products and the results to 'be described are part of an overall 'plan of study covering the heavy industrial clays and shales of Australia. Previous work has been published (Cole and Carthew, 1953; Ferguson, 1954; Ferguson and Hosking, 1955; Cole and Nielsen, 1958/59).In this work no attempt has been made to examine clays from all pits engaged in supplying materials for the structural clay industry. However, in 1954 the senior author collected detailed samples from two pits working in Recent alluvial clays in the Allenby·Gardens and Beverley areas near...

Jan 1, 1963