Search Documents

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By Q Yang

This paper describes the design and construction of three 7.2 m span access ramp-tunnels to the three level underground car park of the newly redeveloped Top Ryde City Shopping Centre in northern Sydney. The tunnels were to be excavated without significant impact on the overlying Devlin Street, one of the busiest arterial roads in the Sydney metropolitan area and a major link in the Sydney road network. The interpretation of the geological conditions indicated that the tunnels would be driven in a formation of heavily jointed, extremely weathered to fresh Triassic Ashfield shale with some structural features such as dyke, fault and shear zones identified in the available boreholes logs. Both empirical and numerical methods were used to design the tunnels and to predict the ground surface settlements. The design solution, which was influenced by the relatively small scale nature of the work and the current demands on the tunnel construction market, included presupport, initial support and permanent steel fibre reinforced shotcrete (SFRS) lining. The interactions of the driven portals with cut and cover sections and the proposed deep excavation of the new shopping centre were considered at the design development stage and in the construction phase to ensure the safety of the live road. The tunnels have been successfully constructed and are now operational.

Mar 8, 2011

By Jorge Ganoza

Los procesos de carbón en pulpa (CIP), carbón en lixiviación y en columna son los más comunes para el tratamiento de soluciones de cianuro que contienen oro, aunque presenten limitaciones como la regeneración del carbón. En ese sentido, el presente texto describe las ventajas de la resina de intercambio iónico puesto que son más versátiles que el carbón activado porque el grupo funcional específico puede ser fijado en la matriz de la resina durante la síntesis. En consecuencia, el carbón activado puede requerir de altas temperaturas para la elución, así como una reactivación térmica.

Aug 1, 2013

By M. K. Mohan

Lead recovery from process solutions contributes not only to the conservation of resources but also clean environment. Zeolites are natural aluminosilicates, which finds applications as catalysts and in wastewater treatment. In the present investigation, studies were taken up on the processing of Pb from process solutions by zeolites. Effects of pH of the solution, time and type of zeolite viz. chabazite, mordenite, erionite and clinoptilolite on the removal of Pb from solutions was investigated. Rate of sorption was found to depend on the pH of the solution and about 99 pct. recovery was observed at pH 6. Optimal conditions were established for the maximum recovery of lead from process solutions. Possible sorption mechanisms were proposed. The calculated adsorption constants calculated from Langmuir and Freundlich equations showed that the adsorption of lead on chabazite was strong.

Jan 1, 1999

By S. Gupta

Froth flotation is a process commonly employed for the selective separation of phosphate from unwanted mineral. Column flotation has become widely accepted in the mineral processing industry, including phosphate industries, due to its ability to improve selectivity, lower operating cost, lower capital cost, and superior control. In this work, a hybrid model is developed that combines a physicochemical model with artificial neural networks. The physicochemical model is based on axial dispersion with first order collection rates. A new approach, in which both frankolite (the desired mineral containing phosphate) and gangue (undesired product) are modeled, enables prediction of grade of the recovered product. Thus, two basic parameters are required in this model: flotation rate constants for frankolite and gangue. Artificial neural networks are used to predict flotation rate constants. The model also takes into account the particle size distribution and predicts grade and recovery for each particle size range. The model then combines grade and recovery for each particle size range to determine the overall grade and recovery of the column. The model is validated against laboratory column data.

Jan 1, 1998

By T. A. Sullivan

The work described in this report was undertaken to evaluate and develop techniques for determining the oxygen content of titanium and titanium alloys. Early investigations of volatilization techniques involving halogenation were unsuccessful. Later efforts were concentrated on evaluating vacuum fusion and inert-gas fusion techniques. Two vacuum fusion methods and an inert-gas fusion method were found to be satisfactory in the 0.02 to 1.00 pct., oxygen range. These methods are described in detail. The coefficient of variation by any of the three methods is approximately 5 pct, While the main portion of this paper is devoted to the vacuum and inert-gas fusion methods, a resume of other suggested methods for analyzing titanium for oxygen also is given. INTRODUCTION The Federal Bureau of Nines has conducted research on titanium metal since 1938. This research included development of the Kroll process for the production of titanium (2)4, various sodium reduction processes for making titanium metal and lower valent titanium chloride-sodium chloride mixtures (17), and a fused salt electrolytic process for Me production of high-purity titanium metal and the recovery of titanium by electrorefining from off-grade materials (20).

Jan 1, 1961

By M. J. Marcinkowski, K. S. Raghavan, A. S. Sastri

A detailed transmission electron microscopy investigation was carried out in connection with a manganese Hadfield Steel. At small plastic strains, numerous individual intrinsic stacking faults are observed. With increased plastic deformation, the stacking faults thicken into twin lamellae which in turn subdivide the original austenite matrix into smaller domains. The twin boundaries act as strong barriers to subsequent dislocation motion and is in a sense equivalent to grain refinement. It is this "grain refinement" which is believed to be the cause of the very high work hardening rates in the Hadfield Steels. In many cases, especially where an hcp phase is the stable one at low temperatures, the stacking fault energy in fcc metals and alloys decreases with decreasing temperature.' Since stacking faults of the intrinsic type are precursors of both twins as well as the hexagonal close packed structure, both of these entities should become more frequent as the temperature of a fcc crystal is lowered. In the case of the twin, there is no chemical driving force for its formation and it is generally necessary to provide the required driving force by an applied stress, i.e., strain energy. In the case of the hcp structure the transformation from the fcc modification can occur spontaneously (marten-sitically) since a decrease in chemical energy does in fact occur; however, an applied stress will provide an even greater driving force toward complete transformation. Since the transformation products mentioned above occur in an inhomogeneous manner throughout the crystal and since these can act as potential barriers to further plastic deformation2 marked strengthening effects can be anticipated. Also because metal and alloy strenghening is in general proportional to the shear modulus, these effects should be greatest in steels of the austenitic type (y), i.e., the fcc types. Perhaps the two most important steels in this category are the austenitic stainless steels and the Hadfield manganese steels. Both may be quenched from elevated temperatures so as to retain the austenitic states characteristic of those temperatures. The effect of subsequent deformation at lower tem- peratures has a profound effect on the stress-strain curves of these alloys. In particular Fig. 1 shows the compressive stress-strain curves obtained with an 18-8 stainless steel which was quenched from 1850°C after annealing for 1 hr so as to produce all y. As the temperature is lowered, the work hardening rate increases markedly. Although some hcp or c mar-tensite can be generated by plastic deformation as the temperature is lowered,~ it is believed to be a transition phase4 and most of the martensite produced is of the bcc or a variety.3 It is this stress induced martensite which gives rise to the very low initial work hardening at 77°K as can be seen in the stress-strain curve in Fig. 1. Similar low initial work hardening rates have been observed in the stress induced Ni-Ti martensites.5 Fig. 2 shows that an even more rapid rate of work hardening occurs in the Hadfield steels treated in the same way as that described for the 18-8 stainless steels a; the temperature is lowered. It is this ability to work harden to such high stress levels that makes the Hadfield steels particularly suitable for armor plate and heavy construction equipment. However, unlike the case of Fig. 1, no initial low rate of work hardening is observed in any of the curves in Fig. 2. Thus the stress induced formation of any low energy martensite phase in any significant quantity must be ruled out. This observation is in accord with the X-ray findings of Otte.~ On the other hand, small quantities of the E phase have been observed by other investigators using transmission electron microscopy (TEM) above Even more significant was the fact that large numbers of deformation twins were observed in the deformed Hadfield steels,678 which were postulated to be one of the reasons for the high work hardening ability of this class of steels.8 It is the purpose in what follows to discuss a series of experimental observations pertaining to the stress induced transformation in a Hadfield steel and to formulate a dislocation mechanism which adequately accounts for the observed results. EXPERIMENTAL PROCEDURE The stainless steel used to obtain the curves shown in Fig. 1 was of the AISI Type 303 containing approximately 18.0 pct Cr and 8 pct Ni. On the other hand, the Hadfield manganese steel used to obtain the curves shown in Fig. 2 contained between 1.00 to 1.25 pct and 11.5 to 13.5 pct Mn. In all cases the samples were in the form of compression cylinders 0.220 in. in diam and 0.370 in. long. Prior to testing the samples were annealed for a hr at 1050°C and rapidly quenched into a brine solution. This treatment was sufficient to preserve the y phase for subsequent testing at lower temperatures. All samples were compressed in an Instron testing machine using a cross head speed of 0.02 in.

Jan 1, 1970

By J. R. Guard

Development of electrical power in coal mining has been an outstanding example of adaptbility. It has accommodated itself to new inventions, changing mining methods, increasing demands, increasing safety requirements and many other new conditions. With the appearance of the continuous miner in the mining machinery picture, those engineers interested in the application of electricity to mining have been thinking about what new comination of electrical apparatus will best suit this newcomer. It is the purpose of this paper to discuss the relative costs of supplying d-c versus a-c power to mining equipment with particular reference to continuous miner setups. Assume that a-c power will be delivered to the mine at some high voltage suitable for transmision to the various substation locations. Typical voltage for this purpose is 4000 volts. The problem then is to change the power to some kind of power suitable for driving the motors of mining equipment. For safety and other reasons the voltage to be delivered to the motor terminals must be under 600 volts.

Jan 6, 1950

By J Say, M Hawtin, L Carlon, P Cann

Historically, production from sublevels of the Ernest Henry Mine (EHM) started from blind uphole rises at the end of slot drives. Where previous investigations considered removing these slot drives and starting production with independent ore drives, any development savings were consumed when drives were extended to minimise ore loss. Since 2017, EHM and Orica have been investigating opportunities to optimise drill and blast practices by implementing Orica’s Wireless Electronic Blasting System (WEBS). To reduce ore drive development metres, a novel design was proposed utilising the WebGen™ 100 system to combine a rise with pre-charged widening firings. Initially these new rise and widening firings achieved results similar to previous EHM designs, achieving on average 81 per cent of design height and width. Due to poor performance of the fourth trial a significant re-design was required. Modifications included drill hole re-positioning, in-hole primer relocation and initiation delay adjustments. Since the re-design a step change in rise performance has been observed with rise and pre-charged widening shots averaging 95 per cent of design height and width. With rise and widening performance exceeding expectations, the removal of slot drives has allowed a substantial reduction in lateral development. Development savings of 165 m and 169 m from the RL1325 and RL1300 levels have been achieved. Primary draw and ore recovery has also increased due to the later addition of pre charged forward stripping rings. Level design changes have also significantly improved the mining cycle by allowing for a reduction in required ground support, improved secondary ventilation, a reduction of critical path development, simpler production scheduling and less wear and tear on machinery. Future mine level designs now incorporate key learnings and are proving beneficial to a variety of scenarios including changing orebody boundaries at depth.

Mar 15, 2021

By P. J. Bethell

Background Increasingly complex geological conditions, with the presence of high ash binders in the mining horizon were encountered at the A.C. I. Dugout Mine near Price, Utah. This led to the production of high ash coal from the Dugout Mine during 2003 and 2004. This material had poor marketability and posed operating issues for the utilities burning the coal. Ash levels increased from typical levels in the 9-12% range to between 15 and 25%. etween 15 and 25%. Reviews of the mine plan and expected geological conditions indicated that further periods of high ash production could be expected. Action Plan Detailed sampling of the mine high ash production was carried out. The majority of the coal from the Dugout Mine is trucked to the Savage Coal Terminal (SCT) at Wellington, Utah where it is stored in multiple piles by quality. Coal at the mine is segregated by a CoalScan 2600, on-line analyzer into high ash, low ash and rock chute (waste material). From these piles, the material is crushed prior to shipment to SCT. The samples obtained from the various high ash piles were subjected to detailed sizing and washability analysis. Once this information was obtained, alternative circuit configurations were evaluated to process this material into a salable product. Water supplies in the arid terrain where the plant is located are scarce. This factor played a part in the final circuit design.

Jan 1, 2008

Transport Canada (Federal Government) constructed the Halifax International Airport (HIA) near Halifax, Nova Scotia, Canada in the late-1950s. Site location criteria were primarily; direct access to the city and a raised flat topography. Unfortunately, the site chosen was located on shallow Meguma group pyritic slate bedrock. In 1982, during the construction of an airport taxiway, it became very apparent that acidic run-off from excavated bedrock at the site was having a negative impact on adjacent aquatic habitat. The ensuing 20 years involved many efforts to rectify the acidic drainage problem with mixed results. Some of the techniques which have been implemented at HIA to address the acid rock drainage (ARD) issue include: dry covers, wet covers, wetlands, electrochemical treatment, open limestone channels, limestone gravel polishing beds, agricultural limestone application, and two hydrated lime [Ca(OH)2] addition treatment plants, the first producing low density sludge and the new one that creates high-density sludge. Based on over 20 years of water quality monitoring data it is apparent that only certain acid drainage mitigation methods have been effective at HIA. In 2000 when the Halifax International Airport Authority (the Authority) took control of the operation and management of the airport, including the ARD issue, it was decided to construct a modern, highdensity sludge, hydrated lime treatment system. This new $CAN 7 million system is now in operation and is achieving compliance with water quality guidelines. Due to high operating cost, a review of methods to optimise the system is being carried out. The HIA ARD problem, though minor by comparison to most mine sites, has provided unique challenges and may provide valuable insights into this urgent environmental and financial issue.

Jan 1, 2003

By Mauritz Kotze, Jason Furtney, Ewan Sellers, Sandy Etchells, Tom Szendrei

The development of a simple model for gas flow and burden movement has driven the need to improve our understanding of burden breakage mechanisms for single hole blasts and the interaction between multiple holes in solid and jointed rock masses. Conventional analytical understandings of the burden breakout using the elastic-tensile fracture model were studied and found to provide a breakout angle that is independent of burden in contradiction to experimental data. By considering rock fracture in terms of Mohr-Coulomb plasticity using analytical expressions from the field of cavity expansion analysis an improved relationship between breakout angle and burden is derived until the point of critical breakout at which the angle of breakout suddenly changes from between 90 degree and 100 degrees to zero. This suggests that the critical burden occurs at about 0.6 times the radial fracture zone calculated from the analytical solutions.

Jan 1, 2013

By R. W. Utley, J. Carr

The tremendous growth in grinding mill size and horsepower during the 70s demanded advancements in gear cutting technology and equipment for the 80s. A new standard in gear cutting machines is now used to generate-cut large open gear sets to over 12.2 m (40 ft) in diameter at an AGMA quality level much higher than the accepted levels a short five years ago. The precision of the resulting gear set assures maximum tooth contact with the resultant longer gear set life.

Jan 1, 1987

By Ralph H. Sweetser

AT the end of 1943 the charcoal pig iron capacity of the United States was at the lowest point in over 1110 years, with only one strictly charcoal blast furnace in operation, and all others permanently out of blast except one in Tennessee d reported to he running on part charcoal and part coke. Such a decrease in production has taken place in spite of the O.P A.'s high-premium price on charcoal pig iron of +34 per ton f.o.b. furnace in Michigan. Depletion of the hardwood supply within fifty mlles or inure of the blast furnace is the reason why; the deplorable lack of reforesting is the cause.

Jan 1, 1944

1. Book reviews Dislocations and properties of real materials, edited by M.H. Loretto. London, The Institute of Metals, 1985. 392 pp. Reviewer: F.R.N. Nabarro Au &Ag heap and dump leaching practice, edited by J.B. Hiskey. AIME, 1984. 162 pp. $20 (member), $15 (student member), $30 (non-member) plus $3.50 for postage and handling. (Order from SME Books, Caller no. D, Littleton, CO 80127, U.S.A.). Reviewer: R.A. Snodgrass The cost and availability of Colombian coal, by Eric D. Jamieson, with the assistance of Kathleen Jamieson. London, lEA Coal Research (14/15 Lower Grosvenor Place, London SWl W OEX). £50 (in member countries), £100 (in non-member countries). Reviewer: W.C. Mather Extraction Metallurgy '85. London, The Institution of Mining and Metallurgy, 1985. £42. Reviewer: R.A. Snodgrass 2. Recent publications Mining annual review 1985. London, Mining Journal, Jun. 1985. 600 pp. £26.50 (surface), £39.50 (air). High heat production (HHP) granites, hydrothermal circulation and ore genesis. London, The Institution of Mining and Metallurgy, 1985. 593 pp. £27 (members), £30 (non-members). Potential mineral resources of Egypt. 144 pp. US$10. Available from Bendix Field Engineering Corporation-MPGAP, Box 1237, Grand Junction, CO 81502, U.S.A. 3. Mintek reports Report M212 South African costs of equipment for the metallurgical industry (1984). Report M213 The response of as-rolled 3CR12 steel to heat treatment. Report M214 A computer programme for use in the development of multi-element X-ray-fluorescence methods of analysis. Report M221 Commodity profiles for selected metals. Report MIO7D Upgrading of alaskite rock to feldspathic sand. (First issued Jun. 1983; reissued Nov. 1985). IMM awards Given below are details of the trust funds to which applications are invited for grants, etc., payable in 1986. Application forms, which must be returned to the Secretary before 17th March, 1986, are available on request. Applicants should note that, in general, preference will be given to members of the Institution.

Jan 1, 1986

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By T. J. Woodside

Prior to 1927 the lead blast furnace charge at El Paso consisted principally of direct-smelting carbonate ores, very low in zinc, and the resulting slag seldom carried more than 4.0 pct. With the exhaustion of the mines in Northern Mexico which supplied these ores, they were supplanted with a much smaller tonnage of sulphide concentrates containing appreciable amounts of zinc, and the zinc content of the slag rose to 10.0 pct. The Anaconda Company's slag fuming plant at East Helena, Montana, had then been in successful operation for several years, and it was immediately recognized that, while at that time the production of high zinc slag was small, if the grade held, a plant for the recovery of zinc from the accumulated slag might some day be practical. The grade not only held but became increasingly higher so that by 1946 suffcient slag had been accumulated to warrant the construction of a fuming plant regardless of future slag production from the blast furnaces, and with the removal of Government restrictions on construction at the end of the war the project was undertaken. The general design of the plant follows that at Bunker Hill, with waste heat boiler, unit coal pulverizers and even more extensive instrumentation and automatic control. The area around the lead blast furnaces is rather congested, being cut off from the nearest feasible site for the fuming plant by the copper plant, so that the most practical route for hot slag transfer is through the converter aisle. For this reason and also to make use of the existing converter cranes to serve the fuming furnace, an unused reverberatory at the north end of the converter building was dismantled and the fuming furnace and boiler located in its place. A flue at right angles to the furnace and boiler runs northward to the U-tube coolers and baghouse (Fig 1). From the bag-house a steel flue runs eastward to an existing and long unused 300 ft con- Crete stack. The coal handling system and de-leading plant lie north of the furnace and east of the cooling tubes and baghouse. The furnace is conventional, 8 X 21 X 33 ft high inside and completely water jacketed (Fig 2). There are 21

Jan 1, 1950

By Byron W. Cheever

In the Journal of the Iron and Steel Institute for 1881 (vol. ii., page 379), will be found an article upon this subject. The analyses there reported mere of samples taken from an ingot made especially rich in impurities and then cast in a sand-mould in order to give the elements a better chance to redistribute themselves, on account of the steel solidifying more slowly than when cast in an iron mould. Wishing to ascertain how much, if any, segregation takes place when the steel is cast in the ordinary way, I placed the subject in the hands of Mr. W. J. Olcott, a graduate of the Michigan University, who has carefully collected and analyzed samples taken from different parts of ingots and billets. In this undertaking he found himself somewhat embarrassed on account of being distant from steel-works, and therefore unable to supervise the selection of samples. He found, however, a competent and willing aid in the person of E. F. Wood, M.E., chemist of the Pittsburgh Bessemer Steel Company, Limited, who has spared no pains in collecting the desired samples and furnishing drawings and descriptions of the ingots from which the samples were taken. The following are the results obtained: Ingot No. 1. This ingot was about 5 feet long and 13 X 131/4 inches at the point of fracture, which was 2 feet from the bottom. The samples

Jan 1, 1885

By Jed H. Mosgrove

Ventilation is the method of producing, conducting, and distributing a constant current of fresh air through mine workings and returning the impure air to the outside atmosphere. Without ventilation no operations are possible in an underground mine. Therefore it is the most important single phase of mining, one on which everything else depends. A good ventilation system, therefore, must be correctly designed, properly conducted as the workings advance, and continually checked to make sure it is functioning correctly. Good air is essential for men to comfortably and safely perform their work. It is also essential to dilute, render harmless, and sweep the mine of any explosive fumes and the gases that are released in varying degrees by all coal seams and the rock strata in which they are contained. GENERAL The body of air that is being moved through the mine, known as the ventilating current, must have a definite way to enter and leave the mine. In other words, there must be a definite intake and return. The main consideration is to get the proper amount of good quality air to the working faces where it is needed. Inasmuch as the mine is divided into sections with interconnecting corridors, known as entries, it is necessary that there be a proper means of conducting the air to the proper points. As a simple explanation of a mine, consider a long tube and think of it in terms of a mine entry ill which the air must pass. The tube must have at least two openings before air can travel through it and this is the same for coal mine entries. The problem in ventilation is to find some means that will cause the air in the tube to flow from one end to the other. The only possible way to do this is to cause greater pressure at one end of the tube than at the other. Air at the end with the greatest pressure would then, of course, flow to the en which has the least pressure. Mine

Jan 1, 1973

By NA NA

Profile of FOSROC, manufacturers and suppliers of products for the mining industry.

Jan 11, 1996